Abstract: This paper describes a low-power second-order filter
for a continuous-time chopper stabilized capacitive sensor interface,
integrated with a fully differential post-CMOS surface-micromachined
MEMS pressure sensor. The circuit uses a single-ended
folded-cascode operational amplifier and two GM-C filters connected
in cascade. The circuit is realized in a 0.18 μm CMOS process and
offers differential to single-ended conversion. The novelty of the
scheme is the cascade of two GM-C filters to achieve a second-order
filter while minimizing power dissipation. The simulated filter cutoff
frequency is 1.14 kHz at common-mode voltage 1.65 V,
operating from a 3.3 V supply while dissipating 172μW of power.
The filter achieves an operating range of 1V for an output load of
1MOhm and 10pF.
Abstract: Pressure waves and Water Hammer occur in a
pumping system when valves are closed or opened suddenly or in
the case of sudden failure of pumps. Determination of maximum
water hammer is considered one of the most important technical
and economical items of which engineers and designers of
pumping stations and conveyance pipelines should take care.
Hammer Software is a recent application used to simulate water
hammer. The present study focuses on determining significance of
each input parameter of the application relative to the maximum
amount of water hammer estimated by the software. The study
determines estimated maximum water hammer variations due to
variations of input parameters including water temperature, pipe
type, thickness and diameter, electromotor rpm and power, and
moment of inertia of electromotor and pump. In our study,
Kuhrang Pumping Station was modeled using WaterGEMS
Software. The pumping station is characterized by total discharge
of 200 liters per second, dynamic height of 194 meters and 1.5
kilometers of steel conveyance pipeline and transports water to
Cheshme Morvarid for farmland irrigation. The model was run in
steady hydraulic condition and transferred to Hammer Software.
Then, the model was run in several unsteady hydraulic conditions
and sensitivity of maximum water hammer to each input parameter
was calculated. It is shown that parameters to which maximum
water hammer is most sensitive are moment of inertia of pump and
electromotor, diameter, type and thickness of pipe and water
temperature, respectively.
Abstract: As a vital activity for companies, new product
development (NPD) is also a very risky process due to the high
uncertainty degree encountered at every development stage and the
inevitable dependence on how previous steps are successfully
accomplished. Hence, there is an apparent need to evaluate new
product initiatives systematically and make accurate decisions under
uncertainty. Another major concern is the time pressure to launch a
significant number of new products to preserve and increase the
competitive power of the company. In this work, we propose an
integrated decision-making framework based on neural networks and
fuzzy logic to make appropriate decisions and accelerate the
evaluation process. We are especially interested in the two initial
stages where new product ideas are selected (go/no go decision) and
the implementation order of the corresponding projects are
determined. We show that this two-staged intelligent approach allows
practitioners to roughly and quickly separate good and bad product
ideas by making use of previous experiences, and then, analyze a
more shortened list rigorously.
Abstract: Natural gas usually includes H2S component which is
very toxic, hazardous and corrosive to environment, human being and
process equipments, respectively. Therefore, sweetening of the gas
(separation of H2S) is inevitable. To achieve this purpose, using
packed-bed columns with liquid absorbents such as MEA or DEA is
very common. Due to some problems of usual packed columns
especially high pressure drop of gas phase, a novel kind of them
called wetted-wire column (WWC) has been invented. The column
decreases the pressure drop significantly and improves the absorption
efficiency. The packings are very thin rods (like wire) and as long as
column. The column has 100 wires with a triangular arrangement and
counter current flows of gas and liquid phases. The observation
showed that at the same conditions, the absorption performance was
quite comparable to conventional packed-bed towers and a very low
pressure drop.
Abstract: This paper details a new concept of using compressed air as a potential zero pollution power source for motorbikes. In place of an internal combustion engine, the motorbike is equipped with an air turbine transforms the energy of the compressed air into shaft work. The mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine is presented in this paper. The effect of isobaric admission and adiabatic expansion of high pressure air for different rotor diameters, casing diameters and ratio of rotor to casing diameters of the turbine have been considered and analyzed. It is concluded that the work output is found optimum for some typical values of rotor / casing diameter ratios. In this study, the maximum power works out to 3.825 kW (5.20 HP) for casing diameter of 200 mm and rotor to casing diameter ratio of 0.65 to 0.60 which is sufficient to run motorbike.
Abstract: In this paper, the dam-reservoir interaction is
analyzed using a finite element approach. The fluid is assumed to be
incompressible, irrotational and inviscid. The assumed boundary
conditions are that the interface of the dam and reservoir is vertical
and the bottom of reservoir is rigid and horizontal. The governing
equation for these boundary conditions is implemented in the
developed finite element code considering the horizontal and vertical
earthquake components. The weighted residual standard Galerkin
finite element technique with 8-node elements is used to discretize
the equation that produces a symmetric matrix equation for the damreservoir
system. A new boundary condition is proposed for
truncating surface of unbounded fluid domain to show the energy
dissipation in the reservoir, through radiation in the infinite upstream
direction. The Sommerfeld-s and perfect damping boundary
conditions are also implemented for a truncated boundary to compare
with the proposed far end boundary. The results are compared with
an analytical solution to demonstrate the accuracy of the proposed
formulation and other truncated boundary conditions in modeling the
hydrodynamic response of an infinite reservoir.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece with copper tools are being optimized
according to its individual machining characteristic i.e. material
removal rate (MRR). Lower MRR during EDM machining process
may decrease its- machining productivity. Hence, the quality
characteristic for MRR is set to higher-the-better to achieve the
optimum machining productivity. Taguchi method has been used
for the construction, layout and analysis of the experiment for each
of the machining characteristic for the MRR. The use of Taguchi
method in the experiment saves a lot of time and cost of preparing
and machining the experiment samples. Therefore, an L18
Orthogonal array which was the fundamental component in the
statistical design of experiments has been used to plan the
experiments and Analysis of Variance (ANOVA) is used to
determine the optimum machining parameters for this machining
characteristic. The control parameters selected for this
optimization experiments are polarity, pulse on duration, discharge
current, discharge voltage, machining depth, machining diameter
and dielectric liquid pressure. The result had shown that the higher
the discharge voltage, the higher will be the MRR.
Abstract: The purpose of this paper is to present a Dynamic
Time Warping technique which reduces significantly the data
processing time and memory size of multi-dimensional time series
sampled by the biometric smart pen device BiSP. The acquisition
device is a novel ballpoint pen equipped with a diversity of sensors
for monitoring the kinematics and dynamics of handwriting
movement. The DTW algorithm has been applied for time series
analysis of five different sensor channels providing pressure,
acceleration and tilt data of the pen generated during handwriting on
a paper pad. But the standard DTW has processing time and memory
space problems which limit its practical use for online handwriting
recognition. To face with this problem the DTW has been applied to
the sum of the five sensor signals after an adequate down-sampling
of the data. Preliminary results have shown that processing time and
memory size could significantly be reduced without deterioration of
performance in single character and word recognition. Further
excellent accuracy in recognition was achieved which is mainly due
to the reduced dynamic time warping RDTW technique and a novel
pen device BiSP.
Abstract: In electronegative-electropositive gas mixtures plasma, at a total pressure varying in the range of ten to hundred Torr, the appearance of a quasi-mochromatization effect of the emitted radiation was reported. This radiation could be the result of the generating mechanisms at molecular level, which is the case of the excimer radiation but also at atomic level. Thus, in the last case, in (Ne+1%Ar/Xe+H2) gas mixtures plasma in a dielectric barrier discharge, this effect, called M-effect, consists in the reduction of the discharge emission spectrum practice at one single, strong spectral line with λ = 585.3 nm. The present paper is concerned with the characteristics comparative investigation of the principal reaction mechanisms involved in the quasi-monochromatization effect existence in the case of the excimer radiation, respectively of the Meffect. Also, the paper points out the role of the metastable electronegative atoms in the appearance of the monochromatization – effect at atomic level.
Abstract: Insulation used in transformer is mostly oil pressboard insulation. Insulation failure is one of the major causes of catastrophic failure of transformers. It is established that partial discharges (PD) cause insulation degradation and premature failure of insulation. Online monitoring of PDs can reduce the risk of catastrophic failure of transformers. There are different techniques of partial discharge measurement like, electrical, optical, acoustic, opto-acoustic and ultra high frequency (UHF). Being non invasive and non interference prone, acoustic emission technique is advantageous for online PD measurement. Acoustic detection of p.d. is based on the retrieval and analysis of mechanical or pressure signals produced by partial discharges. Partial discharges are classified according to the origin of discharges. Their effects on insulation deterioration are different for different types. This paper reports experimental results and analysis for classification of partial discharges using acoustic emission signal of laboratory simulated partial discharges in oil pressboard insulation system using three different electrode systems. Acoustic emission signal produced by PD are detected by sensors mounted on the experimental tank surface, stored on an oscilloscope and fed to computer for further analysis. The measured AE signals are analyzed using discrete wavelet transform analysis and wavelet packet analysis. Energy distribution in different frequency bands of discrete wavelet decomposed signal and wavelet packet decomposed signal is calculated. These analyses show a distinct feature useful for PD classification. Wavelet packet analysis can sort out any misclassification arising out of DWT in most cases.
Abstract: Dynamics of laser radiation – metal target interaction
in water at 1064 nm by applying Mach-Zehnder interference
technique was studied. The mechanism of generating the well
developed regime of evaporation of a metal surface and a spherical
shock wave in water is proposed. Critical intensities of the NIR for
the well developed evaporation of silver and gold targets were
determined. Dynamics of shock waves was investigated for earlier
(dozens) and later (hundreds) nanoseconds of time. Transparent
expanding plasma-vapor-compressed water object was visualized and
measured. The thickness of compressed layer of water and pressures
behind the front of a shock wave for later time delays were obtained
from the optical treatment of interferograms.
Abstract: The influence of eccentric discharge of stored solids in
squat silos has been highly valued by many researchers. However,
calculation method of lateral pressure under eccentric flowing still
needs to be deeply studied. In particular, the lateral pressure
distribution on vertical wall could not be accurately recognized
mainly because of its asymmetry. In order to build mechanical model
of lateral pressure, flow channel and flow pattern of stored solids in
squat silo are studied. In this passage, based on Janssen-s theory, the
method for calculating lateral static pressure in squat silos after
eccentric discharge is proposed. Calculative formulae are deduced for
each of three possible cases. This method is also focusing on
unsymmetrical distribution characteristic of silo wall normal
pressure. Finite element model is used to analysis and compare the
results of lateral pressure and the numerical results illustrate the
practicability of the theoretical method.
Abstract: The current sheath dynamics in plasma focus facilities
is the most important factors. In this paper the current sheath velocity
at three dimensional with Sahand plasma focus facility is
investigated. For this purpose the discharge is produced in argon gas
with deposited energy lying in the range of 20-37kJ. The current
sheath is monitored using two tridimensional magnetic probes. These
probes installed near the surface of the interior electrode (anode) at
125mm from the anode axis (pinch place). The effect of gas pressure
on the current sheath velocity also is investigated.
Abstract: There are three possible effects of Special Theory of
Relativity (STR) on a thermodynamic system. Planck and Einstein
looked upon this process as isobaric; on the other hand Ott saw it as
an adiabatic process. However plenty of logical reasons show that the
process is isotherm. Our phenomenological consideration
demonstrates that the temperature is invariant with Lorenz
transformation. In that case process is isotherm, so volume and
pressure are Lorentz covariant. If the process is isotherm the Boyles
law is Lorentz invariant. Also equilibrium constant and Gibbs energy,
activation energy, enthalpy entropy and extent of the reaction became
Lorentz invariant.
Abstract: Flow through micro and mini channels requires relatively
high driving pressure due to the large fluid pressure drop
through these channels. Consequently the forces acting on the walls of
the channel due to the fluid pressure are also large. Due to these forces
there are displacement fields set up in the solid substrate containing
the channels. If the movement of the substrate is constrained at some
points, then stress fields are established in the substrate. On the other
hand, if the deformation of the channel shape is sufficiently large
then its effect on the fluid flow is important to be calculated. Such
coupled fluid-solid systems form a class of problems known as fluidstructure
interactions. In the present work a co-located finite volume
discretization procedure on unstructured meshes is described for
solving fluid-structure interaction type of problems. A linear elastic
solid is assumed for which the effect of the channel deformation
on the flow is neglected. Thus the governing equations for the
fluid and the solid are decoupled and are solved separately. The
procedure is validated by solving two benchmark problems, one from
fluid mechanics and another from solid mechanics. A fluid-structure
interaction problem of flow through a U-shaped channel embedded
in a plate is solved.
Abstract: The equilibrium chemical reactions taken place in a converter reactor of the Khorasan Petrochemical Ammonia plant was studied using the minimization of Gibbs free energy method. In the minimization of the Gibbs free energy function the Davidon– Fletcher–Powell (DFP) optimization procedure using the penalty terms in the well-defined objective function was used. It should be noted that in the DFP procedure along with the corresponding penalty terms the Hessian matrices for the composition of constituents in the Converter reactor can be excluded. This, in fact, can be considered as the main advantage of the DFP optimization procedure. Also the effect of temperature and pressure on the equilibrium composition of the constituents was investigated. The results obtained in this work were compared with the data collected from the converter reactor of the Khorasan Petrochemical Ammonia plant. It was concluded that the results obtained from the method used in this work are in good agreement with the industrial data. Notably, the algorithm developed in this work, in spite of its simplicity, takes the advantage of short computation and convergence time.
Abstract: Abrasive waterjet is a novel machining process capable of processing wide range of hard-to-machine materials. This research addresses modeling and optimization of the process parameters for this machining technique. To model the process a set of experimental data has been used to evaluate the effects of various parameter settings in cutting 6063-T6 aluminum alloy. The process variables considered here include nozzle diameter, jet traverse rate, jet pressure and abrasive flow rate. Depth of cut, as one of the most important output characteristics, has been evaluated based on different parameter settings. The Taguchi method and regression modeling are used in order to establish the relationships between input and output parameters. The adequacy of the model is evaluated using analysis of variance (ANOVA) technique. The pairwise effects of process parameters settings on process response outputs are also shown graphically. The proposed model is then embedded into a Simulated Annealing algorithm to optimize the process parameters. The optimization is carried out for any desired values of depth of cut. The objective is to determine proper levels of process parameters in order to obtain a certain level of depth of cut. Computational results demonstrate that the proposed solution procedure is quite effective in solving such multi-variable problems.
Abstract: The cycles of the steam-injection gas-turbine systems are studied. The analyses of the parametric effects and the optimal operating conditions for the steam-injection gas-turbine (STIG) system and the regenerative steam-injection gas-turbine (RSTIG) system are investigated to ensure the maximum performance. Using the analytic model, the performance parameters of the system such as thermal efficiency, fuel consumption and specific power, and also the optimal operating conditions are evaluated in terms of pressure ratio, steam injection ratio, ambient temperature and turbine inlet temperature (TIT). It is shown that the computational results are presented to have a notable enhancement of thermal efficiency and specific power.
Abstract: Hydrodynamic pressures acting on upstream of concrete dams during an earthquake are an important factor in designing and assessing the safety of these structures in Earthquake regions. Due to inherent complexities, assessing exact hydrodynamic pressure is only feasible for problems with simple geometry. In this research, the governing equation of concrete gravity dam reservoirs with effect of fluid viscosity in frequency domain is solved and then compared with that in which viscosity is assumed zero. The results show that viscosity influences the reservoir-s natural frequency. In excitation frequencies near the reservoir's natural frequencies, hydrodynamic pressure has a considerable difference in compare to the results of non-viscose fluid.
Abstract: In this study, it is investigated the stability boundary of
Functionally Graded (FG) panel under the heats and supersonic
airflows. Material properties are assumed to be temperature
dependent, and a simple power law distribution is taken. First-order
shear deformation theory (FSDT) of plate is applied to model the
panel, and the von-Karman strain- displacement relations are
adopted to consider the geometric nonlinearity due to large
deformation. Further, the first-order piston theory is used to model the
supersonic aerodynamic load acting on a panel and Rayleigh damping
coefficient is used to present the structural damping. In order to find a
critical value of the speed, linear flutter analysis of FG panels is
performed. Numerical results are compared with the previous works,
and present results for the temperature dependent material are
discussed in detail for stability boundary of the panel with various
volume fractions, and aerodynamic pressures.