Abstract: The seeds of cotton (Gossypium hirsutum) fall among the lesser known oil seeds. Cottonseeds are not normally consumed in their natural state due to their gossypol content, an antinutrient. The effect of processing on the sensory characteristics and chemical composition of cottonseed and its extract was studied by subjecting the cottonseed extract to heat treatment (boiling) and the cottonseed to fermentation. The cottonseed extract was boiled using the open pot and the pressure pot for 30 minutes respectively. The fermentation of the cottonseed was carried out for 6 days with samples withdrawn at intervals of 2 days. The extract and fermented samples were subjected to chemical analysis and sensory evaluated for colour, aroma, taste, mouth feel, appearance and overallacceptability. The open pot sample was more preferred. Fermentation for 6 days resulted into a significant reduction in gossypol level of the cottonseed; however, sample fermented for 2 days was most preferred.
Abstract: In this paper, a two-dimensional (2D) numerical
model for the tidal currents simulation in Persian Gulf is presented.
The model is based on the depth averaged equations of shallow water
which consider hydrostatic pressure distribution. The continuity
equation and two momentum equations including the effects of bed
friction, the Coriolis effects and wind stress have been solved. To
integrate the 2D equations, the Alternative Direction Implicit (ADI)
technique has been used. The base of equations discritization was
finite volume method applied on rectangular mesh. To evaluate the
model validation, a dam break case study including analytical
solution is selected and the comparison is done. After that, the
capability of the model in simulation of tidal current in a real field is
represented by modeling the current behavior in Persian Gulf. The
tidal fluctuations in Hormuz Strait have caused the tidal currents in
the area of study. Therefore, the water surface oscillations data at
Hengam Island on Hormoz Strait are used as the model input data.
The check point of the model is measured water surface elevations at
Assaluye port. The comparison between the results and the
acceptable agreement of them showed the model ability for modeling
marine hydrodynamic.
Abstract: Based on the thermodynamic theory, the dependence of
sublimation energy of metal on temperature and pressure is discussed,
and the results indicate that the sublimation energy decreases linearly
with the increase of temperature and pressure. Combined with this
result, the blow-off impulse of aluminum induced by pulsed X-ray is
simulated by smoothed particle hydrodynamics (SPH) method. The
numerical results show that, while the change of sublimation energy
with temperature and pressure is considered, the blow-off impulse of
aluminum is larger than the case that the sublimation energy is
assumed to be a constant.
Abstract: During the last few years, several sheet hydroforming
processes have been introduced. Despite the advantages of these
methods, they have some limitations. Of the processes, the two main
ones are the standard hydroforming and hydromechanical deep
drawing. A new sheet hydroforming die set was proposed that has the
advantages of both processes and eliminates their limitations. In this
method, a polyurethane plate was used as a part of the die-set to
control the blank holder force. This paper outlines the Taguchi
optimization methodology, which is applied to optimize the effective
parameters in forming cylindrical cups by the new die set of sheet
hydroforming process. The process parameters evaluated in this
research are polyurethane hardness, polyurethane thickness, forming
pressure path and polyurethane hole diameter. The design of
experiments based upon L9 orthogonal arrays by Taguchi was used
and analysis of variance (ANOVA) was employed to analyze the
effect of these parameters on the forming pressure. The analysis of
the results showed that the optimal combination for low forming
pressure is harder polyurethane, bigger diameter of polyurethane hole
and thinner polyurethane. Finally, the confirmation test was derived
based on the optimal combination of parameters and it was shown
that the Taguchi method is suitable to examine the optimization
process.
Abstract: Hydrogen sulfide (H2S) is a very toxic gas that is produced in very large quantities in the oil and gas industry. It cannot be flared to the atmosphere and Claus process based gas plants are used to recover the sulfur and convert the hydrogen to water. In this paper, we present optical characterization of an atmospheric pressure microwave plasma torch for H2S dissociation into hydrogen and sulfur. The torch is operated at 2.45 GHz with power up to 2 kW. Three different gases can simultaneously be injected in the plasma torch. Visual imaging and optical emission spectroscopy are used to characterize the plasma for varying gas flow rates and microwave power. The plasma length, emission spectra and temperature are presented. The obtained experimental results validate our earlier published simulation results of plasma torch.
Abstract: The stability characteristics of water lubricated journal bearings having three axial grooves are obtained theoretically. In this lubricant (water) is fed under pressure from one end of the bearing, through the 3-axial grooves (groove angles may vary). These bearings can use the process fluid as the lubricant, as in the case of feed water pumps. The Reynolds equation is solved numerically by the finite difference method satisfying the boundary conditions. The stiffness and damping coefficient for various bearing number and eccentricity ratios, assuming linear pressure drop along the groove, shows that smaller groove angles better results.
Abstract: Studies on gas solid mass transfer using Supercritical fluid CO2 (SC-CO2) in a packed bed of palm kernels was investigated at operating conditions of temperature 50 °C and 70 °C and pressures ranges from 27.6 MPa, 34.5 MPa, 41.4 MPa and 48.3 MPa. The development of mass transfer models requires knowledge of three properties: the diffusion coefficient of the solute, the viscosity and density of the Supercritical fluids (SCF). Matematical model with respect to the dimensionless number of Sherwood (Sh), Schmidt (Sc) and Reynolds (Re) was developed. It was found that the model developed was found to be in good agreement with the experimental data within the system studied.
Abstract: Citizens are increasingly are provided with choice and
customization in public services and this has now also become a key
feature of higher education in terms of policy roll-outs on personal
development planning (PDP) and more generally as part of the
employability agenda. The goal here is to transform people, in this
case graduates, into active, responsible citizen-workers. A key part of
this rhetoric and logic is the inculcation of graduate attributes within
students. However, there has also been a concern with the issue of
student lack of engagement and perseverance with their studies. This
paper sets out to explore some of these conceptions that link graduate
attributes with citizenship as well as the notion of how identity is
forged through the higher education process. Examples are drawn
from a quality enhancement project that is being operated within the
context of the Scottish higher education system. This is further
framed within the wider context of competing and conflicting
demands on higher education, exacerbated by the current worldwide
economic climate. There are now pressures on students to develop
their employability skills as well as their capacity to engage with
global issues such as behavioural change in the light of
environmental concerns. It is argued that these pressures, in effect,
lead to a form of personalization that is concerned with how
graduates develop their sense of identity as something that is
engineered and re-engineered to meet these demands.
Abstract: At the end of the 20th century it was actual the
development of transport corridors and the improvement of their
technical parameters. With this purpose, many countries and Georgia
among them manufacture to construct new highways, railways and
also reconstruction-modernization of the existing transport
infrastructure. It is necessary to explore the artificial structures
(bridges and tunnels) on the existing tracks as they are very old.
Conference report includes the peculiarities of reconstruction of
tunnels, because we think that this theme is important for the
modernization of the existing road infrastructure. We must remark
that the methods of determining mining pressure of tunnel
reconstructions are worked out according to the jobs of new tunnels
but it is necessary to foresee additional mining pressure which will be
formed during their reconstruction. In this report there are given the
methods of figuring the additional mining pressure while
reconstruction of tunnels, there was worked out the computer
program, it is determined that during reconstruction of tunnels the
additional mining pressure is 1/3rd of main mining pressure.
Abstract: Bubble generation was observed using a high-speed
camera in subcooled flow boiling at low void fraction. Constant heat
flux was applied on one side of an upward rectangular channel to
make heated test channel. Water as a working fluid from high
subcooling to near saturation temperature was injected step by step to
investigate bubble behavior during void development. Experiments
were performed in two different pressures condition close to 2bar and
4bar. It was observed that in high subcooling when boiling was
commenced, bubble after nucleation departed its origin and slid
beside heated surface. In an observation window mean release
frequency of bubble fb,mean, nucleation site Ns and mean bubble
volume Vb,mean in each step of experiments were measured to
investigate wall vaporization rate. It was found that in proximity of
PNVG vaporization rate was increased significantly in compare with
condensation rate which remained in low value.
Abstract: Numerical analysis of flow characteristics and
separation efficiency in a high-efficiency cyclone has been performed.
Several models based on the experimental observation for a design
purpose were proposed. However, the model is only estimated the
cyclone's performance under the limited environments; it is difficult to
obtain a general model for all types of cyclones. The purpose of this
study is to find out the flow characteristics and separation efficiency
numerically. The Reynolds stress model (RSM) was employed instead
of a standard k-ε or a k-ω model which was suitable for isotropic
turbulence and it could predict the pressure drop and the Rankine
vortex very well. For small particles, there were three significant
components (entrance of vortex finder, cone, and dust collector) for
the particle separation. In the present work, the particle re-entraining
phenomenon from the dust collector to the cyclone body was observed
after considerable time. This re-entrainment degraded the separation
efficiency and was one of the significant factors for the separation
efficiency of the cyclone.
Abstract: Worldwide conventional resources of fossil fuel are depleting very fast due to large scale increase in use of transport vehicles every year, therefore consumption rate of oil in transport sector alone has gone very high. In view of this, the major thrust has now been laid upon the search of alternative energy source and also for cost effective energy conversion system. The air converted into compressed form by non conventional or conventional methods can be utilized as potential working fluid for producing shaft work in the air turbine and thus offering the capability of being a zero pollution energy source. This paper deals with the mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine. Effect of expansion action and steady flow work in the air turbine at high admission air pressure of 6 bar, for varying injection to vane angles ratios 0.2-1.6, at the interval of 0.2 and at different vane angles such as 30o, 45o, 51.4o, 60o, 72o, 90o, and 120o for 12, 8, 7, 6, 5, 4 and 3 vanes respectively at speed of rotation 2500 rpm, has been quantified and analyzed here. Study shows that the expansion power has major contribution to total power, whereas the contribution of flow work output has been found varying only up to 19.4%. It is also concluded that for variation of injection to vane angle ratios from 0.2 to 1.2, the optimal power output is seen at vane angle 90o (4 vanes) and for 1.4 to 1.6 ratios, the optimal total power is observed at vane angle 72o (5 vanes). Thus in the vaned type novel air turbine the optimum shaft power output is developed when rotor contains 4-5 vanes for almost all situations of injection to vane angle ratios from 0.2 to 1.6.
Abstract: This paper presents a computational study of the separated flow in a planer asymmetric diffuser. The steady RANS equations for turbulent incompressible fluid flow and six turbulence closures are used in the present study. The commercial software code, FLUENT 6.3.26, was used for solving the set of governing equations using various turbulence models. Five of the used turbulence models are available directly in the code while the v2-f turbulence model was implemented via User Defined Scalars (UDS) and User Defined Functions (UDF). A series of computational analysis is performed to assess the performance of turbulence models at different grid density. The results show that the standard k-ω, SST k-ω and v2-f models clearly performed better than other models when an adverse pressure gradient was present. The RSM model shows an acceptable agreement with the velocity and turbulent kinetic energy profiles but it failed to predict the location of separation and attachment points. The standard k-ε and the low-Re k- ε delivered very poor results.
Abstract: The scroll pump belongs to the category of positive
displacement pump can be used for continuous pumping of gases at
low pressure apart from general vacuum application. The shape of
volume occupied by the gas moves and deforms continuously as the
spiral orbits. To capture flow features in such domain where mesh
deformation varies with time in a complicated manner, mesh less
solver was found to be very useful. Least Squares Kinetic Upwind
Method (LSKUM) is a kinetic theory based mesh free Euler solver
working on arbitrary distribution of points. Here upwind is enforced
in molecular level based on kinetic flux vector splitting scheme
(KFVS). In the present study we extended the LSKUM to moving
node viscous flow application. This new code LSKUM-NS-MN for
moving node viscous flow is validated for standard airfoil pitching
test case. Simulation performed for flow through scroll pump using
LSKUM-NS-MN code agrees well with the experimental pumping
speed data.
Abstract: In this work, axisymetric CFD simulation of fixed bed
GTL reactor has been conducted, using computational fluid dynamics
(CFD). In fixed bed CFD modeling, when N (tube-to-particle
diameter ratio) has a large value, it is common to consider the packed
bed as a porous media. Synthesis gas (a mixture of predominantly
carbon monoxide and hydrogen) was fed to the reactor. The reactor
length was 20 cm, divided to three sections. The porous zone was in
the middle section of the reactor. The model equations were solved
employing finite volume method. The effects of particle diameter,
bed voidage, fluid velocity and bed length on pressure drop have
been investigated. Simulation results showed these parameters could
have remarkable impacts on the reactor pressure drop.
Abstract: This paper presents the new results of energy plant –
rye and triticale at yellow ripeness and ripe, pre-treatment in high
pressure steam reactor and monosaccharide extraction. There were
investigated the influence of steam pressure (20 to 22 bar), retention
duration (180 to 240 s) and catalytic sulphuric acid concentration
strength (0 to 0.5 %) on the pre-treatment process, contents of
monosaccharides (glucose, arabinose, xylose, mannose) and
undesirable by-compounds (furfural and HMF) in the reactor. The
study has determined that the largest amount of monosaccharides
(37.2 % of glucose, 2.7 % of arabinose, 8.4 % of xylose, and 1.3 %
of mannose) was received in the rye at ripe, the samples of which
were mixed with 0.5 % concentration of catalytic sulphuric acid, and
hydrolysed in the reactor, where the pressure was 20 bar, whereas the
reaction time – 240 s.
Abstract: We consider here the subsonic impinging jet
representing the flow field of a vertical take-off aircraft or the initial
stage of rocket launching. Implicit Large-Eddy Simulation (ILES) is
used to calculate the time-dependent flow field and the radiate sound
pressure associated with jet impinging. With proper boundary
treatments and high-order numerical scheme, the near field sound
pressure is successfully obtained. Results are presented for both a
rectangular as well a circular jet.
Abstract: The purpose of this study is to derive optimal shapes of
a body located in viscous flows by the finite element method using the
acoustic velocity and the four-step explicit scheme. The formulation
is based on an optimal control theory in which a performance function
of the fluid force is introduced. The performance function should be
minimized satisfying the state equation. This problem can be transformed
into the minimization problem without constraint conditions
by using the adjoint equation with adjoint variables corresponding to
the state equation. The performance function is defined by the drag
and lift forces acting on the body. The weighted gradient method
is applied as a minimization technique, the Galerkin finite element
method is used as a spatial discretization and the four-step explicit
scheme is used as a temporal discretization to solve the state equation
and the adjoint equation. As the interpolation, the orthogonal basis
bubble function for velocity and the linear function for pressure
are employed. In case that the orthogonal basis bubble function is
used, the mass matrix can be diagonalized without any artificial
centralization. The shape optimization is performed by the presented
method.
Abstract: This paper presents a study on the thermodynamics
and transport properties of hot potassium carbonate aqueous system
(HPC) using electrolyte non-random two liquid, (ELECNRTL)
model. The operation conditions are varied to determine the system
liquid phase stability range at the standard and critical conditions. A
case study involving 30 wt% K2CO3, H2O standard system at
pressure of 1 bar and temperature range from 280.15 to 366.15 K has
been studied. The estimated solubility index, viscosity, water
activity, and density which obtained from the simulation showed a
good agreement with the experimental work. Furthermore, the
saturation temperature of the solution has been estimated.
Abstract: In the upstream we place a piece of ring and rotate
it with 83Hz, 166Hz, 333Hz,and 666H to find the effect of the
periodic distortion.In the experiment this type of the perturbation
will not allow since the mechanical failure of any parts of the
equipment in the upstream will destroy the blade system. This type of
study will be only possible by CFD. We use two pumps NS32
(ENSAM) and three blades pump (Tamagawa Univ). The benchmark
computations were performed without perturbation parts, and confirm
the computational results well agreement in head-flow rate. We
obtained the pressure fluctuation growth rate that is representing the
global instability of the turbo-system. The fluctuating torque
components were 0.01Nm(5000rpm), 0.1Nm(10000rmp),
0.04Nm(20000rmp), 0.15Nm( 40000rmp) respectively. Only for
10000rpm(166Hz) the output toque was random, and it implies that it
creates unsteady flow by separations on the blades, and will reduce the
pressure loss significantly