Abstract: Prickly pear fruit (Opuntia ficus indica L. Miller) belongs to the Cactaceae family. This species is very sensitive to low storage temperatures (< 5°C) which cause damages. The fruits can be peeled, suitably packaged and successfully commercialized as a ready-to-eat product. The main limit to the extension of the shelf life is the production of off-flavors due to different factors, the growth of microorganisms and the action of endogenous enzymes. Lipoxygenase (LOX) and Pectinesterase (PE) are involved in fruit degradation. In particular, LOX pathway is directly responsible for lipid oxidation, and the subsequent production of off-flavours, while PE causes the softening of fruit during maturation. They act on the texture and shelf-life of post-harvest, packaged fruits, as a function of the the grown of microorganisms and packaging technologies used. The aim of this work is to compare the effect of different packaging technologies on the shelf life extension of ready-to-eat prickly pear fruits with regards for the enzymes activities.
Abstract: Dual motor drives fed by single inverter is
purposely designed to reduced size and cost with respect to
single motor drives fed by single inverter. Previous researches
on dual motor drives only focus on the modulation and the
averaging techniques. Only a few of them, study the
performance of the drives based on different speed controller
other than Proportional and Integrator (PI) controller. This
paper presents a detailed comparative study on fuzzy rule-base
in Fuzzy Logic speed Controller (FLC) for Dual Permanent
Magnet Synchronous Motor (PMSM) drives. Two fuzzy speed
controllers which are standard and simplified fuzzy speed
controllers are designed and the results are compared and
evaluated. The standard fuzzy controller consists of 49 rules
while the proposed controller consists of 9 rules determined by
selecting the most dominant rules only. Both designs are
compared for wide range of speed and the robustness of both
controllers over load disturbance changes is tested to
demonstrate the effectiveness of the simplified/reduced rulebase.
Abstract: In [4], Kipnis and Shamir have cryptanalised
a version of HFE of degree 2. In this paper, we describe the
generalization of this attack of HFE of degree more than 2.
We are based on Fourier Transformation to acheive partially
this attack.
Abstract: In the present work, we have developed a symmetric electrochemical capacitor based on the nanostructured iron oxide (Fe3O4)-activated carbon (AC) nanocomposite materials. The physical properties of the nanocomposites were characterized by Scanning Electron Microscopy (SEM) and Brunauer-Emmett-Teller (BET) analysis. The electrochemical performances of the composite electrode in 1.0 M Na2SO3 and 1.0 M Na2SO4 aqueous solutions were evaluated using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The composite electrode with 4 wt% of iron oxide nanomaterials exhibits the highest capacitance of 86 F/g. The experimental results clearly indicate that the incorporation of iron oxide nanomaterials at low concentration to the composite can improve the capacitive performance, mainly attributed to the contribution of the pseudocapacitance charge storage mechanism and the enhancement on the effective surface area of the electrode. Nevertheless, there is an optimum threshold on the amount of iron oxide that needs to be incorporated into the composite system. When this optimum threshold is exceeded, the capacitive performance of the electrode starts to deteriorate, as a result of the undesired particle aggregation, which is clearly indicated in the SEM analysis. The electrochemical performance of the composite electrode is found to be superior when Na2SO3 is used as the electrolyte, if compared to the Na2SO4 solution. It is believed that Fe3O4 nanoparticles can provide favourable surface adsorption sites for sulphite (SO3 2-) anions which act as catalysts for subsequent redox and intercalation reactions.
Abstract: UML is a collection of notations for capturing a software system specification. These notations have a specific syntax defined by the Object Management Group (OMG), but many of their constructs only present informal semantics. They are primarily graphical, with textual annotation. The inadequacies of standard UML as a vehicle for complete specification and implementation of real-time embedded systems has led to a variety of competing and complementary proposals. The Real-time UML profile (UML-RT), developed and standardized by OMG, defines a unified framework to express the time, scheduling and performance aspects of a system. We present in this paper a framework approach aimed at deriving a complete specification of a real-time system. Therefore, we combine two methods, a semiformal one, UML-RT, which allows the visual modeling of a realtime system and a formal one, CSP+T, which is a design language including the specification of real-time requirements. As to show the applicability of the approach, a correct design of a real-time system with hard real time constraints by applying a set of mapping rules is obtained.
Abstract: The scope of this paper is to describe a real electrical
installation of renewable energy using photovoltaic cells. The
displayed power grid connected network was established in 2007 at
area of Northern Greece. The photovoltaic park is composed of 6120
photovoltaic cells able to deliver a total power of 1.101.600 Wp. For
the transformation of DC voltage to AC voltage have been used 25
stand alone three phases inverters and for the connection at the
medium voltage network of Greek Power Authority have been
installed two oil immersed transformer of 630 kVA each one. Due to
the wide space area of installation a specific external lightning
protection system has been designed. Additionally, due to the
sensitive electronics of the control and protection systems of park,
surge protection, equipotent bonding and shielding were also of
major importance.
Abstract: Bacillus subtilis strain LB5 produced lipopeptide
antibiotic iturin A-2 in liquid medium. Crude extract
from cell-free supernatant of B. subtilis cultivated broth extracted
with n-butanol showed antifungal activity to conidial germination of
Colletotrichum gloeosporioides. The germination of conidia was
completely inhibited by crude extract. The ultrastructure of conidia
after treated with crude extract was found an accumulation of vesiclelike
material between cell wall and plasma membrane while this
accumulation was not observed in untreated and germinated conidia.
Besides, the cell wall was not affected by crude extract.
Abstract: Many recent electrophysiological studies have
revealed the importance of investigating meditation state in order to
achieve an increased understanding of autonomous control of
cardiovascular functions. In this paper, we characterize heart rate
variability (HRV) time series acquired during meditation using
nonlinear dynamical parameters. We have computed minimum
embedding dimension (MED), correlation dimension (CD), largest
Lyapunov exponent (LLE), and nonlinearity scores (NLS) from HRV
time series of eight Chi and four Kundalini meditation practitioners.
The pre-meditation state has been used as a baseline (control) state to
compare the estimated parameters. The chaotic nature of HRV during
both pre-meditation and meditation is confirmed by MED. The
meditation state showed a significant decrease in the value of CD and
increase in the value of LLE of HRV, in comparison with premeditation
state, indicating a less complex and less predictable nature
of HRV. In addition, it was shown that the HRV of meditation state
is having highest NLS than pre-meditation state. The study indicated
highly nonlinear dynamic nature of cardiac states as revealed by
HRV during meditation state, rather considering it as a quiescent
state.
Abstract: As many scientific applications require large data processing, the importance of parallel I/O has been increasingly recognized. Collective I/O is one of the considerable features of parallel I/O and enables application programmers to easily handle their large data volume. In this paper we measured and analyzed the performance of original collective I/O and the subgroup method, the way of using collective I/O of MPI effectively. From the experimental results, we found that the subgroup method showed good performance with small data size.
Abstract: The deterministic quantum transfer-matrix (QTM)
technique and its mathematical background are presented. This
important tool in computational physics can be applied to a class of
the real physical low-dimensional magnetic systems described by the
Heisenberg hamiltonian which includes the macroscopic molecularbased
spin chains, small size magnetic clusters embedded in some
supramolecules and other interesting compounds. Using QTM, the
spin degrees of freedom are accurately taken into account, yielding
the thermodynamical functions at finite temperatures.
In order to test the application for the susceptibility calculations to
run in the parallel environment, the speed-up and efficiency of
parallelization are analyzed on our platform SGI Origin 3800 with
p = 128 processor units. Using Message Parallel Interface (MPI)
system libraries we find the efficiency of the code of 94% for
p = 128 that makes our application highly scalable.
Abstract: The performance of mortar subjected to high
temperature and cooled in normal ambient temperature was examined
in the laboratory to comply with the situation of burning & cooling of
a structure. Four series of cubical (5 X 5 X 5 cm) mortar specimens
were made from OPC, and partial replacement (10, 15, 20, 25 &
30%) of OPC by Rice Husk Ash (RHA) produced in the uncontrolled
environment. These specimens were heated in electric furnace to 200,
300, 400, 500 and 7000C. The specimens were kept in normal room
temperature for cooling. They were then tested for mechanical
properties and the results shows that particular 20% RHA mixed
mortar shows better fire performance.
Abstract: This paper proposes a Fuzzy Sliding Mode Control (FSMC) as a control strategy for Buck-Boost DC-DC converter. The proposed fuzzy controller specifies changes in the control signal based on the knowledge of the surface and the surface change to satisfy the sliding mode stability and attraction conditions. The performances of the proposed fuzzy sliding controller are compared to those obtained by a classical sliding mode controller. The satisfactory simulation results show the efficiency of the proposed control law which reduces the chattering phenomenon. Moreover, the obtained results prove the robustness of the proposed control law against variation of the load resistance and the input voltage of the studied converter.
Abstract: Knowledge is indispensable but voluminous knowledge becomes a bottleneck for efficient processing. A great challenge for data mining activity is the generation of large number of potential rules as a result of mining process. In fact sometimes result size is comparable to the original data. Traditional data mining pruning activities such as support do not sufficiently reduce the huge rule space. Moreover, many practical applications are characterized by continual change of data and knowledge, thereby making knowledge voluminous with each change. The most predominant representation of the discovered knowledge is the standard Production Rules (PRs) in the form If P Then D. Michalski & Winston proposed Censored Production Rules (CPRs), as an extension of production rules, that exhibit variable precision and supports an efficient mechanism for handling exceptions. A CPR is an augmented production rule of the form: If P Then D Unless C, where C (Censor) is an exception to the rule. Such rules are employed in situations in which the conditional statement 'If P Then D' holds frequently and the assertion C holds rarely. By using a rule of this type we are free to ignore the exception conditions, when the resources needed to establish its presence, are tight or there is simply no information available as to whether it holds or not. Thus the 'If P Then D' part of the CPR expresses important information while the Unless C part acts only as a switch changes the polarity of D to ~D. In this paper a scheme based on Dempster-Shafer Theory (DST) interpretation of a CPR is suggested for discovering CPRs from the discovered flat PRs. The discovery of CPRs from flat rules would result in considerable reduction of the already discovered rules. The proposed scheme incrementally incorporates new knowledge and also reduces the size of knowledge base considerably with each episode. Examples are given to demonstrate the behaviour of the proposed scheme. The suggested cumulative learning scheme would be useful in mining data streams.
Abstract: The uniform Roe C*-algebra (also called uniform translation)C^*- algebra provides a link between coarse geometry and C^*- algebra theory. The uniform Roe algebra has a great importance in geometry, topology and analysis. We consider some of the elementary concepts associated with coarse spaces.
Abstract: Evolutionary robotics is concerned with the design of
intelligent systems with life-like properties by means of simulated
evolution. Approaches in evolutionary robotics can be categorized
according to the control structures that represent the behavior and the
parameters of the controller that undergo adaptation. The basic idea
is to automatically synthesize behaviors that enable the robot to
perform useful tasks in complex environments. The evolutionary
algorithm searches through the space of parameterized controllers
that map sensory perceptions to control actions, thus realizing a
specific robotic behavior. Further, the evolutionary algorithm
maintains and improves a population of candidate behaviors by
means of selection, recombination and mutation. A fitness function
evaluates the performance of the resulting behavior according to the
robot-s task or mission. In this paper, the focus is in the use of
genetic algorithms to solve a multi-objective optimization problem
representing robot behaviors; in particular, the A-Compander Law is
employed in selecting the weight of each objective during the
optimization process. Results using an adaptive fitness function show
that this approach can efficiently react to complex tasks under
variable environments.
Abstract: State Dependent Riccati Equation (SDRE) approach is
a modification of the well studied LQR method. It has the capability of being applied to control nonlinear systems. In this paper the technique
has been applied to control the single inverted pendulum (SIP) which represents a rich class of nonlinear underactuated systems. SIP
modeling is based on Euler-Lagrange equations. A procedure is developed
for judicious selection of weighting parameters and constraint handling. The controller designed by SDRE technique here gives better results than existing controllers designed by energy based techniques.
Abstract: The environmental factors such as temperature and
relative humidity are very contribute to the effect of comfort, health,
performance and worker productivity. To ensure an ergonomics work
environment, it is possible to require a specific attention especially in
industries. The aim of this study is to show the effect of temperature
and relative humidity on worker productivity in automotive industry
by taking a workstation in an automotive plant as the location to
conduct the study. From the analysis of the data, there were
relationship between temperature and relative humidity on worker
productivity. Mathematical equation to represent the relationship
between temperatures and relative humidity on the production rate is
modelled. From the equation model, the production rate for the
workstation can be predicted base on the value of temperature and
relative humidity.
Abstract: The interrelationship between international stock
markets has been a key study area among the financial market
researchers for international portfolio management and risk
measurement. The characteristics of security returns and their
dynamics play a vital role in the financial market theory. This study
is an attempt to find out the dynamic linkages among the equity
market of USA and emerging markets of Pakistan and India using
daily data covering the period of January 2003–December 2009. The
study utilizes Johansen (Journal of Economic Dynamics and Control,
12, 1988) and Johansen and Juselius (Oxford Bulletin of Economics
and Statistics, 52, 1990) cointegration procedure for long run
relationship and Granger-causality tests based on Toda and
Yamamoto (Journal of Econometrics, 66, 1995) methodology.
No cointegration was found among stock markets of USA, Pakistan
and India, while Granger-causality test showed the evidence of
unidirectional causality running from New York stock exchange to
Bombay and Karachi stock exchanges.
Abstract: The paper presents the applications of artificial
intelligence technique called adaptive tabu search to design the
controller of a buck converter. The averaging model derived from the
DQ and generalized state-space averaging methods is applied to
simulate the system during a searching process. The simulations
using such averaging model require the faster computational time
compared with that of the full topology model from the software
packages. The reported model is suitable for the work in the paper in
which the repeating calculation is needed for searching the best
solution. The results will show that the proposed design technique
can provide the better output waveforms compared with those
designed from the classical method.
Abstract: The adoption of building information modeling (BIM)
is increasing in the construction industry. However, quantity
surveyors are slow in adoption compared to other professions due to
lack of awareness of the BIM’s potential in their profession. It is still
unclear on how BIM application can enhance quantity surveyors’
work performance and project performance. The aim of this research
is to identify the capabilities of BIM in quantity surveying practices
and examine the relationship between BIM capabilities and project
performance. Questionnaire survey and interviews were adopted for
data collection. Literature reviews identified there are eleven BIM
capabilities in quantity surveying practice. Questionnaire results
showed that there are several BIM capabilities significantly
correlated with project performance in time, cost and quality aspects
and the results were validated through interviews. These findings
show that BIM has the capabilities to enhance quantity surveyors’
performances and subsequently improved project performance.