Abstract: In Orthogonal Frequency Division Multiplexing (OFDM) systems, the peak to average power ratio (PAR) is much high. The clipping signal scheme is a useful method to reduce PAR. Clipping the OFDM signal, however, increases the overall noise level by introducing clipping noise. It is necessary to recover the figure of the original signal at receiver in order to reduce the clipping noise. Considering the continuity of the signal and the figure of the peak, we obtain a certain conic function curve to replace the clipped signal module within the clipping time. The results of simulation show that the proposed scheme can reduce the systems? BER (bit-error rate) 10 times when signal-to-interference-and noise-ratio (SINR) equals to 12dB. And the BER performance of the proposed scheme is superior to that of kim's scheme, too.
Abstract: In the gas refineries of Iran-s South Pars Gas
Complex, Sulfrex demercaptanization process is used to remove
volatile and corrosive mercaptans from liquefied petroleum gases by
caustic solution. This process consists of two steps. Removing low
molecular weight mercaptans and regeneration exhaust caustic. Some
parameters such as LPG feed temperature, caustic concentration and
feed-s mercaptan in extraction step and sodium mercaptide content in
caustic, catalyst concentration, caustic temperature, air injection rate
in regeneration step are effective factors. In this paper was focused on
temperature factor that play key role in mercaptans extraction and
caustic regeneration. The experimental results demonstrated by
optimization of temperature, sodium mercaptide content in caustic
because of good oxidation minimized and sulfur impurities in
product reduced.
Abstract: An experiment was conducted in October 2008 due the ability replacement plant associate biofertilizers by chemical fertilizers and the qualifying rate of chemical N fertilizers at the moment of using this biofertilizers and the interaction of this biofertilizer on each other. This field experiment has been done in Persepolis (Throne of Jamshid) and arrange by using factorial with the basis of randomized complete block design, in three replication Azespirilium SP bacteria has been admixed with consistence 108 cfu/g and inoculated with seeds of wheat, The streptomyces SP has been used in amount of 550 gr/ha and concatenated on clay and for the qualifying range of chemical fertilizer 4 level of N chemical fertilizer from the source of urea (N0=0, N1=60, N2=120, N3=180) has been used in this experiment. The results indicated there were Significant differences between levels of Nitrogen fertilizer in the entire characteristic which has been measured in this experiment. The admixed Azespirilium SP showed significant differences between their levels in the characteristics such as No. of fertile ear, No. of grain per ear, grain yield, grain protein percentage, leaf area index and the agronomic fertilizer use efficiency. Due the interaction streptomyses with Azespirilium SP bacteria this actinomycet didn-t show any statistically significant differences between it levels.
Abstract: Dynamic shear test on simulated phantom can be used
to validate magnetic resonance elastography (MRE) measurements.
Phantom gel has been usually utilized for the cell culture of cartilage
and soft tissue and also been used for mechanical property
characterization using imaging systems. The viscoelastic property of
the phantom would be important for dynamic experiments and
analyses. In this study, An axisymmetric FE model is presented for
determining the dynamic shear behaviour of brain simulated phantom
using ABAQUS. The main objective of this study was to investigate
the effect of excitation frequencies and boundary conditions on shear
modulus and shear viscosity in viscoelastic media.
Abstract: In the Northern hemisphere, sheep reproduction is
seasonal (September-November). Among several natural factors
influencing the reproduction status of rams, we studied the daylight
length and temperature. Rams from different breeds were studied:
Merinos de Palas (half-precocious), Karakul de Botosani (halfbelated)
and Turcana (belated breed, low reproductive plasticity). In
Merinos de Palas, ejaculate volume during sexual repose is 51.3%
from normal quantity. When autumn climate was experimentally
induced, ejaculate volume reached 98.45% (Merinos), 94.97%
(Karakul) and 97.59% (Turcana). Semen density increased from
1.031-1.033 till 1.035 after exposition to artificial light and
temperature conditions. Spermatozoids mobility and sperm pH
improved, passing over 82% and 6.75, values identical to those in the
natural reproduction season. Behaviour analysis after
photoperiodicity indicated that over 83.3% Merinos and Karakul
males and all Turcana rams exteriorised normal and intense sexual
reflexes. Certain effort and reduced expenses brought rams in good
condition, producing higher quantity and quality sperm.
Abstract: In the present paper the results of a numerical study are presented, numerical models were developed to simulate the behaviour of vertical massive dikes. The proposed models were developed according to the geometry, boundary conditions, loading conditions and initial conditions of a physical model taken as reference. The results obtained were compared to the experimental data. As far as the overall behaviour, the displacements and the failure mechanisms of the dikes is concerned, the numerical results were in good agreement with the experimental results, which clearly indicates a good quality of numerical modelling. The validated numerical models were used in a parametric study were the displacements and failure mechanisms were fully investigated. Out of the results obtained, some conclusions and recommendations related to the design of massive dikes are proposed.
Abstract: Adopting Zakowski-s upper approximation operator
C and lower approximation operator C, this paper investigates
granularity-wise separations in covering approximation spaces. Some
characterizations of granularity-wise separations are obtained by
means of Pawlak rough sets and some relations among granularitywise
separations are established, which makes it possible to research
covering approximation spaces by logical methods and mathematical
methods in computer science. Results of this paper give further
applications of Pawlak rough set theory in pattern recognition and
artificial intelligence.
Abstract: Mobile robots are used in a large field of scenarios,
like exploring contaminated areas, repairing oil rigs under water,
finding survivors in collapsed buildings, etc. Currently, there is no
unified intuitive user interface (UI) to control such complex mobile
robots. As a consequence, some scenarios are done without the
exploitation of experience and intuition of human teleoperators.
A novel framework has been developed to embed a flexible and
modular UI into a complete 3-D virtual reality simulation system.
This new approach wants to access maximum benefits of human
operators. Sensor information received from the robot is prepared for
an intuitive visualization. Virtual reality metaphors support the
operator in his decisions. These metaphors are integrated into a real
time stereo video stream. This approach is not restricted to any
specific type of mobile robot and allows for the operation of different
robot types with a consistent concept and user interface.
Abstract: Swedish truck industry is investigating the possibility
for implementing the use of Compacted Graphite Iron (CGI) in their
heavy duty diesel engines. Compared to the alloyed gray iron used
today, CGI has superior mechanical properties but not as good
machinability. Another issue that needs to be addressed when
implementing CGI is the inhomogeneous microstructure when the
cast component has different section thicknesses, as in cylinder
blocks. Thinner sections results in finer pearlite, in the material, with
higher strength. Therefore an investigation on its influence on
machinability was needed. This paper focuses on the effect that
interlamellar distance in pearlite has on CGI machinability and
material physical properties. The effect of pearlite content and
nodularity is also examined. The results showed that interlamellar
distance in pearlite did not have as large effect on the material
physical properties or machinability as pearlite content. The paper
also shows the difficulties of obtaining a homogeneous
microstructure in inhomogeneous workpieces.
Abstract: Investigations of the unimolecular decomposition of
vinyl ethyl ether (VEE), vinyl propyl ether (VPE) and vinyl butyl
ether (VBE) have shown that activation of the molecule of a ether
results in formation of a cyclic construction - the transition state (TS),
which may lead to the displacement of the thermodynamic
equilibrium towards the reaction products. The TS is obtained by
applying energy minimization relative to the ground state of an ether
under the program MM2 when taking into account the hydrogen bond
formation between a hydrogen atom of alkyl residue and the extreme
atom of carbon of the vinyl group. The dissociation of TS up to the
products is studied by energy minimization procedure using the
mathematical program Gaussian. The obtained calculation data for
VEE testify that the decomposition of this ether may be conditioned
by hydrogen bond formation for two possible versions: when α- or β-
hydrogen atoms of the ethyl group are bound to carbon atom of the
vinyl group. Applying the same calculation methods to other ethers
(VPE and VBE) it is shown that only in the case of hydrogen bonding
between α-hydrogen atom of the alkyl residue and the extreme atom
of carbon of the vinyl group (αH---C) results in decay of theses
ethers.
Abstract: Air conditioning is mainly to be used as human
comfort medium. It has been use more often in country in which the
daily temperatures are high. In scientific, air conditioning is defined
as a process of controlling the moisture, cooling, heating and cleaning
air. Without proper estimation of cooling load, big amount of waste
energy been used because of unsuitable of air conditioning system are
not considering to overcoming heat gains from surrounding. This is
due to the size of the room is too big and the air conditioning has to
use more energy to cool the room and the air conditioning is too
small for the room. The studies are basically to develop a program to
calculate cooling load. Through this study it is easy to calculate
cooling load estimation. Furthermore it-s help to compare the cooling
load estimation by hourly and yearly. Base on the last study that been
done, the developed software are not user-friendly. For individual
without proper knowledge of calculating cooling load estimation
might be problem. Easy excess and user-friendly should be the main
objective to design something. This program will allow cooling load
able be estimate by any users rather than estimation by using rule of
thumb. Several of limitation of case study is judged to sure it-s
meeting to Malaysia building specification. Finally validation is done
by comparison manual calculation and by developed program.
Abstract: The storage of thermal energy as a latent heat of phase
change material (PCM) has created considerable interest among
researchers in recent times. Here, an attempt is made to carry out
numerical investigations to analyze the performance of latent heat
storage units (LHSU) employing phase change material. The
mathematical model developed is based on an enthalpy formulation.
Freezing time of PCM packed in three different shaped containers
viz. rectangular, cylindrical and cylindrical shell is compared. The
model is validated with the results available in the literature. Results
show that for the same mass of PCM and surface area of heat
transfer, cylindrical shell container takes the least time for freezing
the PCM and this geometric effect is more pronounced with an
increase in the thickness of the shell than that of length of the shell.
Abstract: The pulp and paper mill effluent is one of the high
polluting effluent amongst the effluents obtained from polluting
industries. All the available methods for treatment of pulp and paper
mill effluent have certain drawbacks. The coagulation is one of the
cheapest process for treatment of various organic effluents. Thus, the
removal of chemical oxygen demand (COD) and colour of paper mill
effluent is studied using coagulation process. The batch coagulation
process was performed using various coagulants like: aluminium
chloride, poly aluminium chloride and copper sulphate. The initial
pH of the effluent (Coagulation pH) has tremendous effect on COD
and colour removal. Poly aluminium chloride (PAC) as coagulant
reduced COD to 84 % and 92 % of colour was removed at an
optimum pH 5 and coagulant dose of 8 ml l-1. With aluminium
chloride at an optimum pH = 4 and coagulant dose of 5 g l-1, 74 %
COD and 86 % colour removal were observed. The results using
copper sulphate as coagulant (a less commercial coagulant) were
encouraging. At an optimum pH 6 and mass loading of 5 g l-1, 76 %
COD reduction and 78 % colour reduction were obtained. It was also
observed that after addition of coagulant, the pH of the effluent
decreases. The decrease in pH was highest for AlCl3, which was
followed by PAC and CuSO4. Significant amount of COD reductions
was obtained by coagulation process. Since the coagulation process
is the first stage for treatment of effluent and some of the coagulant
cations usually remain in the treated effluents. Thus, cation like
copper may be one of the good catalyst for second stage of treatment
process like wet oxidation. The copper has been found to be good
oxidation catalyst then iron and aluminum.
Abstract: The fundamental aim of extended expansion concept is
to achieve higher work done which in turn leads to higher thermal
efficiency. This concept is compatible with the application of
turbocharger and LHR engine. The Low Heat Rejection engine was
developed by coating the piston crown, cylinder head inside with
valves and cylinder liner with partially stabilized zirconia coating of
0.5 mm thickness. Extended expansion in diesel engines is termed as
Miller cycle in which the expansion ratio is increased by reducing the
compression ratio by modifying the inlet cam for late inlet valve
closing. The specific fuel consumption reduces to an appreciable level
and the thermal efficiency of the extended expansion turbocharged
LHR engine is improved.
In this work, a thermodynamic model was formulated and
developed to simulate the LHR based extended expansion
turbocharged direct injection diesel engine. It includes a gas flow
model, a heat transfer model, and a two zone combustion model. Gas
exchange model is modified by incorporating the Miller cycle, by
delaying inlet valve closing timing which had resulted in considerable
improvement in thermal efficiency of turbocharged LHR engines. The
heat transfer model, calculates the convective and radiative heat
transfer between the gas and wall by taking into account of the
combustion chamber surface temperature swings. Using the two-zone
combustion model, the combustion parameters and the chemical
equilibrium compositions were determined. The chemical equilibrium
compositions were used to calculate the Nitric oxide formation rate by
assuming a modified Zeldovich mechanism. The accuracy of this
model is scrutinized against actual test results from the engine. The
factors which affect thermal efficiency and exhaust emissions were
deduced and their influences were discussed. In the final analysis it is
seen that there is an excellent agreement in all of these evaluations.
Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetical and thermal stresses remain major failures for
insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: This research proposed a new design of helmet-shaped
array transcranial magnetic stimulation coil system. It was constructed
using several sagittal directional wires and several coronal directional
wires. By varying the current direction and strength on each wire, this
array coil system could be constructed into the circular coil and
figure-eight coil of different size. Also, this proposed coil system can
flexibly not only change the stimulation location, range, type and
strength, but also change the shape and the channel number of coil
dynamically.
Abstract: In the article there have been revealed the properties
of designing the research teaching the military masters and in the context it has been offered the program of mastering by the masters
military men the methodology of research work, in the course of practical teaching activity there has been considered the developed
and approbated model of organization of the process of mastering by the masters the methodology of research work. As a whole, the research direction of master preparation leaves its
sign to the content of education, forms of organization of educational
process, scientific work of masters. In this connection the offered in
the article properties of organization of research teaching and a model
of organization of mastering by the masters military men the methodology of research work can be taken into account when
designing the content of master preparation.
Abstract: The selection for plantation of a particular type of
mustard plant depending on its productivity (pod yield) at the stage
of maturity. The growth of mustard plant dependent on some
parameters of that plant, these are shoot length, number of leaves,
number of roots and roots length etc. As the plant is growing, some
leaves may be fall down and some new leaves may come, so it can
not gives the idea to develop the relationship with the seeds weight at
mature stage of that plant. It is not possible to find the number of
roots and root length of mustard plant at growing stage that will be
harmful of this plant as roots goes deeper to deeper inside the land.
Only the value of shoot length which increases in course of time can
be measured at different time instances. Weather parameters are
maximum and minimum humidity, rain fall, maximum and minimum
temperature may effect the growth of the plant. The parameters of
pollution, water, soil, distance and crop management may be
dominant factors of growth of plant and its productivity. Considering
all parameters, the growth of the plant is very uncertain, fuzzy
environment can be considered for the prediction of shoot length at
maturity of the plant. Fuzzification plays a greater role for
fuzzification of data, which is based on certain membership
functions. Here an effort has been made to fuzzify the original data
based on gaussian function, triangular function, s-function,
Trapezoidal and L –function. After that all fuzzified data are
defuzzified to get normal form. Finally the error analysis
(calculation of forecasting error and average error) indicates the
membership function appropriate for fuzzification of data and use to
predict the shoot length at maturity. The result is also verified using
residual (Absolute Residual, Maximum of Absolute Residual, Mean
Absolute Residual, Mean of Mean Absolute Residual, Median of
Absolute Residual and Standard Deviation) analysis.
Abstract: Steganography meaning covered writing. Steganography includes the concealment of information within computer files [1]. In other words, it is the Secret communication by hiding the existence of message. In this paper, we will refer to cover image, to indicate the images that do not yet contain a secret message, while we will refer to stego images, to indicate an image with an embedded secret message. Moreover, we will refer to the secret message as stego-message or hidden message. In this paper, we proposed a technique called RGB intensity based steganography model as RGB model is the technique used in this field to hide the data. The methods used here are based on the manipulation of the least significant bits of pixel values [3][4] or the rearrangement of colors to create least significant bit or parity bit patterns, which correspond to the message being hidden. The proposed technique attempts to overcome the problem of the sequential fashion and the use of stego-key to select the pixels.
Abstract: In this paper, a class of impulsive BAM fuzzy cellular neural networks with distributed delays and reaction-diffusion terms is formulated and investigated. By employing the delay differential inequality and inequality technique developed by Xu et al., some sufficient conditions ensuring the existence, uniqueness and global exponential stability of equilibrium point for impulsive BAM fuzzy cellular neural networks with distributed delays and reaction-diffusion terms are obtained. In particular, the estimate of the exponential convergence rate is also provided, which depends on system parameters, diffusion effect and impulsive disturbed intention. It is believed that these results are significant and useful for the design and applications of BAM fuzzy cellular neural networks. An example is given to show the effectiveness of the results obtained here.