Abstract: This work deals with problems of tool axis inclination angles in ball-end milling. Tool axis inclination angle contributes to improvement of functional surface properties (surface integrity - surface roughness, residual stress, micro hardness, etc.), decreasing cutting forces and improving production. By milling with ball-end milling tool, using standard way of cutting, when work piece and cutting tool contain right angle, we have zero cutting speed on edge. At this point cutting tool only pushes material into the work piece. Here we can observe the following undesirable effects - chip contraction, increasing of cutting temperature, increasing vibrations or creation of built-up edge. These effects have negative results – low quality of surface and decreasing of tool life (in the worse case even it is pinching out). These effects can be eliminated with the tilt of cutting tool or tilt of work piece.
Abstract: Thermally insulating ceramic coatings also known as
thermal barrier coatings (TBCs) have been essential technologies to
improve the performance and efficiency of advanced gas turbines in
service at extremely high temperatures. The damage mechanisms of
air-plasma sprayed YSZ thermal barrier coatings (TBC) with various
microstructures were studied by microscopic techniques after thermal
cycling. The typical degradation of plasma TBCs that occurs during
cyclic furnace testing of an YSZ and alumina coating on a Titanium
alloy are analyzed. During the present investigation the effects of
topcoat thickness, bond coat oxidation, thermal cycle lengths and test
temperature are investigated using thermal cycling. These results
were correlated with stresses measured by a spectroscopic technique
in order to understand specific damage mechanism. The failure
mechanism of former bond coats was found to involve fracture
initiation at the thermally grown oxide (TGO) interface and at the
TGO bond coat interface. The failure mechanism of the YZ was
found to involve combination of fracture along the interface between
TGO and bond coat.
Abstract: In recent years in Kazakhstan, as well as in all countries, we have been talking not only about the professional stress, but also professional Burnout Syndrome of employees. Burnout is essentially a response to chronic emotional stress – manifests itself in the form of chronic fatigue, despondency, unmotivated aggression, anger, and others. This condition is due to mental fatigue among teachers as a sort of payment for overstrain when professional commitments include the impact of “heat your soul", emotional investment. The emergence of professional Burnout among teachers is due to the system of interrelated and mutually reinforcing factors relating to the various levels of the personality: individually-psychological level is psychodynamic special subject characteristics of valuemotivational sphere and formation of skills and habits of selfregulation; the socio-psychological level includes especially the Organization and interpersonal interaction of a teacher. Signs of the Burnout were observed in 15 testees, and virtually a symptom could be observed in every teacher. As a result of the diagnosis 48% of teachers had the signs of stress (phase syndrome), resulting in a sense of anxiety, mood, heightened emotional susceptibility. The following results have also been got:-the fall of General energy potential – 14 pers. -Psychosomatic and psycho vegetative syndrome – 26 pers. -emotional deficit-34 pers. -emotional Burnout Syndrome-6 pers. The problem of professional Burnout of teachers in the current conditions should become not only meaningful, but particularly relevant. The quality of education of the younger generation depends on professional development; teachers- training level, and how “healthy" teachers are. That is why the systematic maintenance of pedagogic-professional development for teachers (including disclosure of professional Burnout Syndrome factors) takes on a special meaning.
Abstract: The aim of this paper is to introduce a parametric
distribution model in fatigue life reliability analysis dealing with
variation in material properties. Service loads in terms of responsetime
history signal of Belgian pave were replicated on a multi-axial
spindle coupled road simulator and stress-life method was used to
estimate the fatigue life of automotive stub axle. A PSN curve was
obtained by monotonic tension test and two-parameter Weibull
distribution function was used to acquire the mean life of the
component. A Pearson system was developed to evaluate the fatigue
life reliability by considering stress range intercept and slope of the
PSN curve as random variables. Considering normal distribution of
fatigue strength, it is found that the fatigue life of the stub axle to
have the highest reliability between 10000 – 15000 cycles. Taking
into account the variation of material properties associated with the
size effect, machining and manufacturing conditions, the method
described in this study can be effectively applied in determination of
probability of failure of mass-produced parts.
Abstract: In this paper, the potential use of an exponential
hidden Markov model to model a hidden pavement deterioration
process, i.e. one that is not directly measurable, is investigated. It is
assumed that the evolution of the physical condition, which is the
hidden process, and the evolution of the values of pavement distress
indicators, can be adequately described using discrete condition states
and modeled as a Markov processes. It is also assumed that condition
data can be collected by visual inspections over time and represented
continuously using an exponential distribution. The advantage of
using such a model in decision making process is illustrated through
an empirical study using real world data.
Abstract: Iran is one of the greatest producers of date in the
world. However due to lack of information about its viscoelastic
properties, much of the production downgraded during harvesting
and postharvesting processes. In this study the effect of temperature
and moisture content of product were investigated on stress
relaxation characteristics. Therefore, the freshly harvested date
(kabkab) at tamar stage were put in controlled environment chamber
to obtain different temperature levels (25, 35, 45, and 55 0C) and
moisture contents (8.5, 8.7, 9.2, 15.3, 20, 32.2 %d.b.). A texture
analyzer TAXT2 (Stable Microsystems, UK) was used to apply
uniaxial compression tests. A chamber capable to control temperature
was designed and fabricated around the plunger of texture analyzer to
control the temperature during the experiment. As a new approach a
CCD camera (A4tech, 30 fps) was mounted on a cylindrical glass
probe to scan and record contact area between date and disk.
Afterwards, pictures were analyzed using image processing toolbox
of Matlab software. Individual date fruit was uniaxially compressed
at speed of 1 mm/s. The constant strain of 30% of thickness of date
was applied to the horizontally oriented fruit. To select a suitable
model for describing stress relaxation of date, experimental data were
fitted with three famous stress relaxation models including the
generalized Maxwell, Nussinovitch, and Pelege. The constant in
mentioned model were determined and correlated with temperature
and moisture content of product using non-linear regression analysis.
It was found that Generalized Maxwell and Nussinovitch models
appropriately describe viscoelastic characteristics of date fruits as
compared to Peleg mode.
Abstract: In the present paper, the three-dimensional
temperature field of tool is determined during the machining and
compared with experimental work on C45 workpiece using carbide
cutting tool inserts. During the metal cutting operations, high
temperature is generated in the tool cutting edge which influence on
the rate of tool wear. Temperature is most important characteristic of
machining processes; since many parameters such as cutting speed,
surface quality and cutting forces depend on the temperature and high
temperatures can cause high mechanical stresses which lead to early
tool wear and reduce tool life. Therefore, considerable attention is
paid to determine tool temperatures. The experiments are carried out
for dry and orthogonal machining condition. The results show that
the increase of tool temperature depends on depth of cut and
especially cutting speed in high range of cutting conditions.
Abstract: Fundamental motivation of this paper is how gaze estimation can be utilized effectively regarding an application to games. In games, precise estimation is not always important in aiming targets but an ability to move a cursor to an aiming target accurately is also significant. Incidentally, from a game producing point of view, a separate expression of a head movement and gaze movement sometimes becomes advantageous to expressing sense of presence. A case that panning a background image associated with a head movement and moving a cursor according to gaze movement can be a representative example. On the other hand, widely used technique of POG estimation is based on a relative position between a center of corneal reflection of infrared light sources and a center of pupil. However, a calculation of a center of pupil requires relatively complicated image processing, and therefore, a calculation delay is a concern, since to minimize a delay of inputting data is one of the most significant requirements in games. In this paper, a method to estimate a head movement by only using corneal reflections of two infrared light sources in different locations is proposed. Furthermore, a method to control a cursor using gaze movement as well as a head movement is proposed. By using game-like-applications, proposed methods are evaluated and, as a result, a similar performance to conventional methods is confirmed and an aiming control with lower computation power and stressless intuitive operation is obtained.
Abstract: It is well known that the abrasive particles in the
abrasive water suspension has significant effect on the erosion
characteristics of the inside surface of the nozzle. Abrasive particles
moving with the flow cause severe skin friction effect, there by
altering the nozzle diameter due to wear which in turn reflects on the
life of the nozzle for effective machining. Various commercial
abrasives are available for abrasive water jet machining. The erosion
characteristic of each abrasive is different. In consideration of this
aspect, in the present work, the effect of abrasive materials namely
garnet, aluminum oxide and silicon carbide on skin friction
coefficient due to wall shear stress and jet kinetic energy has been
analyzed. It is found that the abrasive material of lower density
produces a relatively higher skin friction effect and higher jet exit
kinetic energy.
Abstract: Optical Coherence Tomography (OCT) combined
with the Confocal Microscopy, as a noninvasive method, permits the
determinations of materials defects in the ceramic layers depth. For
this study 256 anterior and posterior metal and integral ceramic fixed
partial dentures were used, made with Empress (Ivoclar), Wollceram
and CAD/CAM (Wieland) technology. For each investigate area 350
slices were obtain and a 3D reconstruction was perform from each
stuck. The Optical Coherent Tomography, as a noninvasive method,
can be used as a control technique in integral ceramic technology,
before placing those fixed partial dentures in the oral cavity. The
purpose of this study is to evaluate the capability of En face Optical
Coherence Tomography (OCT) combined with a fluorescent method
in detection and analysis of possible material defects in metalceramic
and integral ceramic fixed partial dentures. As a conclusion,
it is important to have a non invasive method to investigate fixed
partial prostheses before their insertion in the oral cavity in order to
satisfy the high stress requirements and the esthetic function.
Abstract: This study was conducted to determine effect of water stress on chlorophyll content and chlorophyll fluorescence parameter in young `Dezful- olive trees. Three irrigation regimes (40% ETcrop, 65% ETcrop and 100% ETcrop) were used. After irrigation treatments were applied, some of biochemical parameters including chlorophyll a, b, total chlorophyll, chlorophyll fluorescence and also chlorophyll content index (C.C.I) were measured. Results of Analysis of variance showed that irrigation treatments had significant effect on chlorophylla, total chlorophyll (chl a+b), C.C.I and Fv/Fm ratio. The amount of decreased chlorophyll a and total chlorophyll in plants were received 40% ETcrop were 51.55% and 46.86%, respectively, compared with 100% ETcrop.
Abstract: This paper focuses on operational risk measurement
techniques and on economic capital estimation methods. A data
sample of operational losses provided by an anonymous Central
European bank is analyzed using several approaches. Loss
Distribution Approach and scenario analysis method are considered.
Custom plausible loss events defined in a particular scenario are
merged with the original data sample and their impact on capital
estimates and on the financial institution is evaluated. Two main
questions are assessed – What is the most appropriate statistical
method to measure and model operational loss data distribution? and
What is the impact of hypothetical plausible events on the financial
institution? The g&h distribution was evaluated to be the most
suitable one for operational risk modeling. The method based on the
combination of historical loss events modeling and scenario analysis
provides reasonable capital estimates and allows for the measurement
of the impact of extreme events on banking operations.
Abstract: The equations governing the flow of an electrically conducting, incompressible viscous fluid over an infinite flat plate in the presence of a magnetic field are investigated using the homotopy perturbation method (HPM) with Padé approximants (PA) and 4th order Runge–Kutta method (4RKM). Approximate analytical and numerical solutions for the velocity field and heat transfer are obtained and compared with each other, showing excellent agreement. The effects of the magnetic parameter and Prandtl number on velocity field, shear stress, temperature and heat transfer are discussed as well.
Abstract: When the characteristic length of an elastic solid is
down to the nanometer level, its deformation behavior becomes size
dependent. Surface energy /surface stress have recently been applied
to explain such dependency. In this paper, the effect of
strain-independent surface stress on the deformation of an isotropic
elastic solid containing a nanosized elliptical hole is studied by the
finite element method. Two loading cases are considered, in the first
case, hoop stress along the rim of the elliptical hole induced by pure
surface stress is studied, in the second case, hoop stress around the
elliptical opening under combined remote tension and surface stress is
investigated. It has been shown that positive surface stress induces
compressive hoop stress along the hole, and negative surface stress has
opposite effect, maximum hoop stress occurs near the major semi-axes
of the ellipse. Under combined loading of remote tension and surface
stress, stress concentration around the hole can be either intensified or
weakened depending on the sign of the surface stress.
Abstract: The paper discuses the effect of initial stresses on the reflection coefficients of plane waves in a dissipative medium. Basic governing equations are formulated in context of Biot's incremental deformation theory. These governing equations are solved analytically to obtain the dimensional phase velocities of plane waves propagating in plane of symmetry. Closed-form expressions for the reflection coefficients of P and SV waves- incident at the free surface of an initially stressed dissipative medium are obtained. Numerical computations, using these expressions, are carried out for a particular model. Computations made with the results predicted in presence and absence of the initial stresses and the results have been shown graphically. The study shows that the presence of compressive initial stresses increases the velocity of longitudinal wave (P-wave) but diminishes that of transverse wave (SV-wave). Also the numerical results presented indicate that initial stresses and dissipation might affect the reflection coefficients significantly.
Abstract: Tehran, one of the heavily-populated capitals, is
severely suffering from increasing air pollution. To show a
documented trend of such pollutants during last years, plane tree
species (Platanus orientalis) were suited to be studied as indicators,
for the species have been planted throughout the city many years
ago. Two areas (Saadatabad and Narmak districts) allotting different
contents of crowed and highly-traffic routs but the same ecological
characteristics were selected. Twelve sample individuals were cored
twice perpendicularly in each area. Tree-rings of each core were
measured by a binocular microscope and separated annually for the
last 25 years. Two heavy metals including Cd and Pb accompanied
by a mineral element (Ca) were analyzed using Hatch method. Treerings
analysis of the two areas showed different groups in term of
physiologically ability as the growths were plunged during the last
10 years in Saadatabad district and showed a slight decrease in the
same period for another studying area. In direct contrast to
decreasing growth trend in Saadatabad, all three mentioned elements
increased sharply during last 25 years in the same area. When it came
to Narmak district, the trend was completely different with
Saadatabad. There were some fluctuations in absorbing trace
elements like tree-rings widths were, yet calcium showed an upward
trend all the last 25 years. The results of the study proved the
possibility of using tree species of each region to monitor its air
pollution trends of the past, hence to depict a pollution assessment of
a populated city for last years and then to make appropriate decisions
for the future as it is well-known what the trend is. On the other
hand, risen values of calcium (as the stress-indicator element)
accompanied by increased trace elements suggests non-sustainable
state of the trees.
Abstract: Lateral expansion is a factor defining the level of
confinement in reinforced concrete columns. Therefore, predicting
the lateral strain relationship with axial strain becomes an important
issue. Measuring lateral strains in experiments is difficult and only
few report experimental lateral strains. Among the existing analytical
formulations, two recent models are compared with available test
results in this paper with shortcomings highlighted. A new analytical
model is proposed here for lateral strain axial strain relationship and
is based on the supposition that the concrete behaves linear elastic in
the early stages of loading and then nonlinear hardening up to the
peak stress and then volumetric expansion. The proposal for the
lateral strain axial strain relationship after the peak stress is mainly
based on the hypothesis that the plastic lateral strain varies linearly
with the plastic axial strain and it is shown that this is related to the
lateral confinement level.
Abstract: In this paper, the application of thermal spray
coatings in high speed shafts by a revolution up to 23000 RPM
has been studied. Gas compressor shafts are worn in contact
zone with journal therefore will be undersized. Wear
mechanisms of compressor shaft were identified. The
predominant wear mechanism is abrasion wear. The worn
surface was coated by hard WC-Co cermets using high
velocity oxy fuel (HVOF) after preparation. The shafts were in
satisfactory service in 8000h period. The metallurgical and
Tribological studies has been made on the worn and coated
shaft using optical microscopy, scanning electron microscopy
(SEM) and X-ray diffraction.
Abstract: Whit the increasing of traffic, noise emanated from
motor vehicles increases as well, which subsequently causes adding
to the stress of modern city. Thus, it is needed to look for most
critical areas in terms of environmental and social impact of noise.
There are several critical situations for noise emanated from motor
vehicles such as stop and go situation which usually occurs near
junctions or at-grade intersections. This study was conducted in two
locations, most common types of intersections, crossroads and Tjunctions.
The highest average noise levels are recorded during Go
phase for T-junction, 64.4 dB, and Drive phase for crossroad, 64 dB.
It implies that the existence of intersection caused the noise level to
increase. The vehicles starting to move produce more sound than
when they travel at a constant speed along the intersection. It is
suggested that special considerations and priority of allocating funds
should be given to these critical spots.
Abstract: This paper looks at transgender identities and the law in the context of marriage. It particularly focuses on the role of language and definition in classifying transgendered individuals into a legal category. Two lines of cases in transgender jurisprudence are examined. The former cases decided the definition of 'man' and 'woman' on the basis of biological criteria while the latter cases held that biological factors should not be the sole criterion for defining a man or a woman. Three categories were found to classify transgender people, namely male, female and "monstrous". Since transgender people challenge the core gender distinction that the law stresses, they are often regarded as problematic and monstrous which caused them to be subjected to severe legal consequences. This paper discusses these issues by analyzing and comparing different cases in transgender jurisprudence as well as examining how these issues play out in contemporary Hong Kong.