Abstract: The relationship between different types of Molybdenum disulfide greases under extreme pressure loading and different speed situations have been studied using Design of Experiment (DOE) under 1200rpm steady state rotational speed and cyclic frequencies between 2400 and 1200rpm using a Plint machine software to set up the different rotational speed situations.
Research described here is aimed at providing good friction and wear performance while optimizing cyclic frequencies and MoS2 concentration due to the recent concern about grease behavior in extreme pressure applications. Extreme load of 785 Newton was used in conjunction with different cyclic frequencies (2400rpm -3.75min, 1200rpm -7.5min, 2400rpm -3.75min, 1200rpm -7.5min), to examine lithium based grease with and without MoS2 for equal number of revolutions, and a total run of 36000 revolutions; then compared to 1200rpm steady speed for the same total number of revolutions. 4 Ball wear tester was utilized to run large number of experiments randomly selected by the DOE software. The grease was combined with fine grade MoS2 or technical grade then heated to 750C and the wear scar width was collected at the end of each test. DOE model validation results verify that the data were very significant and can be applied to a wide range of extreme pressure applications. Based on simulation results and Scanning Electron images (SEM), it has been found that wear was largely dependent on the cyclic frequency condition. It is believed that technical grade MoS2 greases under faster cyclic speeds perform better and provides antiwear film that can resist extreme pressure loadings. Figures showed reduced wear scars width and improved frictional values.
Abstract: The work describes the use of a synthetic transmit
aperture (STA) with a single element transmitting and all elements
receiving in medical ultrasound imaging. STA technique is a novel
approach to today-s commercial systems, where an image is acquired
sequentially one image line at a time that puts a strict limit on the
frame rate and the amount of data needed for high image quality. The
STA imaging allows to acquire data simultaneously from all
directions over a number of emissions, and the full image can be
reconstructed.
In experiments a 32-element linear transducer array with 0.48 mm
inter-element spacing was used. Single element transmission aperture
was used to generate a spherical wave covering the full image region.
The 2D ultrasound images of wire phantom are presented obtained
using the STA and commercial ultrasound scanner Antares to
demonstrate the benefits of the SA imaging.
Abstract: Classification of Persian printed numeral characters
has been considered and a proposed system has been introduced. In
representation stage, for the first time in Persian optical character
recognition, extended moment invariants has been utilized as
characters image descriptor. In classification stage, four different
classifiers namely minimum mean distance, nearest neighbor rule,
multi layer perceptron, and fuzzy min-max neural network has been
used, which first and second are traditional nonparametric statistical
classifier. Third is a well-known neural network and forth is a kind of
fuzzy neural network that is based on utilizing hyperbox fuzzy sets.
Set of different experiments has been done and variety of results has
been presented. The results showed that extended moment invariants
are qualified as features to classify Persian printed numeral
characters.
Abstract: Camera calibration is an important step in 3D
reconstruction. Camera calibration may be classified into two major types: traditional calibration and self-calibration. However, a calibration method in using a checkerboard is intermediate between traditional calibration and self-calibration. A self
is proposed based on a square in this paper. Only a square in the planar
template, the camera self-calibration can be completed through the single view. The proposed algorithm is that the virtual circle and straight line are established by a square on planar template, and
circular points, vanishing points in straight lines and the relation
between them are be used, in order to obtain the image of the absolute
conic (IAC) and establish the camera intrinsic parameters. To make
the calibration template is simpler, as compared with the Zhang Zhengyou-s method. Through real experiments and experiments, the experimental results show that this algorithm is
feasible and available, and has a certain precision and robustness.
Abstract: The amount and heterogeneity of data in biomedical research, notably in interdisciplinary research, requires new methods for the collection, presentation and analysis of information. Important data from laboratory experiments as well as patient trials are available but come out of distributed resources. The Charite Medical School in Berlin has established together with the German Research Foundation (DFG) a new information service center for kidney diseases and transplantation (Open European Nephrology Science Centre - OpEN.SC). The system is based on a service-oriented architecture (SOA) with main and auxiliary modules arranged in four layers. To improve the reuse and efficient arrangement of the services the functionalities are described as business processes using the standardised Business Process Execution Language (BPEL).
Abstract: Analysis and visualization of microarraydata is veryassistantfor biologists and clinicians in the field of diagnosis and treatment of patients. It allows Clinicians to better understand the structure of microarray and facilitates understanding gene expression in cells. However, microarray dataset is a complex data set and has thousands of features and a very small number of observations. This very high dimensional data set often contains some noise, non-useful information and a small number of relevant features for disease or genotype. This paper proposes a non-linear dimensionality reduction algorithm Local Principal Component (LPC) which aims to maps high dimensional data to a lower dimensional space. The reduced data represents the most important variables underlying the original data. Experimental results and comparisons are presented to show the quality of the proposed algorithm. Moreover, experiments also show how this algorithm reduces high dimensional data whilst preserving the neighbourhoods of the points in the low dimensional space as in the high dimensional space.
Abstract: There has been a growing interest in implementing humanoid avatars in networked virtual environment. However, most existing avatar communication systems do not take avatars- social backgrounds into consideration. This paper proposes a novel humanoid avatar animation system to represent personalities and facial emotions of avatars based on culture, profession, mood, age, taste, and so forth. We extract semantic keywords from the input text through natural language processing, and then the animations of personalized avatars are retrieved and displayed according to the order of the keywords. Our primary work is focused on giving avatars runtime instruction from multiple natural languages. Experiments with Chinese, Japanese and English input based on the prototype show that interactive avatar animations can be displayed in real time and be made available online. This system provides a more natural and interesting means of human communication, and therefore is expected to be used for cross-cultural communication, multiuser online games, and other entertainment applications.
Abstract: Lateral expansion is a factor defining the level of
confinement in reinforced concrete columns. Therefore, predicting
the lateral strain relationship with axial strain becomes an important
issue. Measuring lateral strains in experiments is difficult and only
few report experimental lateral strains. Among the existing analytical
formulations, two recent models are compared with available test
results in this paper with shortcomings highlighted. A new analytical
model is proposed here for lateral strain axial strain relationship and
is based on the supposition that the concrete behaves linear elastic in
the early stages of loading and then nonlinear hardening up to the
peak stress and then volumetric expansion. The proposal for the
lateral strain axial strain relationship after the peak stress is mainly
based on the hypothesis that the plastic lateral strain varies linearly
with the plastic axial strain and it is shown that this is related to the
lateral confinement level.
Abstract: Stable bacterial polymorphism on a single limiting resource may appear if between the evolved strains metabolic interactions take place that allow the exchange of essential nutrients [8]. Towards an attempt to predict the possible outcome of longrunning evolution experiments, a network based on the metabolic capabilities of homogeneous populations of every single gene knockout strain (nodes) of the bacterium E. coli is reconstructed. Potential metabolic interactions (edges) are allowed only between strains of different metabolic capabilities. Bacterial communities are determined by finding cliques in this network. Growth of the emerged hypothetical bacterial communities is simulated by extending the metabolic flux balance analysis model of Varma et al [2] to embody heterogeneous cell population growth in a mutual environment. Results from aerobic growth on 10 different carbon sources are presented. The upper bounds of the diversity that can emerge from single-cloned populations of E. coli such as the number of strains that appears to metabolically differ from most strains (highly connected nodes), the maximum clique size as well as the number of all the possible communities are determined. Certain single gene deletions are identified to consistently participate in our hypothetical bacterial communities under most environmental conditions implying a pattern of growth-condition- invariant strains with similar metabolic effects. Moreover, evaluation of all the hypothetical bacterial communities under growth on pyruvate reveals heterogeneous populations that can exhibit superior growth performance when compared to the performance of the homogeneous wild-type population.
Abstract: This paper proposes a method which reduces power consumption in single-error correcting, double error-detecting checker circuits that perform memory error correction code. Power is minimized with little or no impact on area and delay, using the degrees of freedom in selecting the parity check matrix of the error correcting codes. The genetic algorithm is employed to solve the non linear power optimization problem. The method is applied to two commonly used SEC-DED codes: standard Hamming and odd column weight Hsiao codes. Experiments were performed to show the performance of the proposed method.
Abstract: An electrical apparatus for measuring moisture
content was developed by our laboratory and uses dependence of
electrical properties on water content in studied material. Error
analysis of the apparatus was run by measuring different volumes of
water in a simplified specimen, i.e. hollow plexiglass block, in order
to avoid as many side-effects as possible. Obtained data were
processed using both basic and advanced statistics and results were
compared with each other. The influence of water content on
accuracy of measured data was studied as well as the influence of
variation of apparatus' proper arrangement or factual methodics of its
usage. The overall coefficient of variation was 4%. There was no
trend found in results of error dependence on water content.
Comparison with current surveys led to a conclusion, that the studied
apparatus can be used for indirect measurement of water content in
porous materials, with expectable error and under known conditions.
Factual experiments with porous materials are not involved, but are
currently under investigation.
Abstract: Frequency domain independent component analysis has
a scaling indeterminacy and a permutation problem. The scaling
indeterminacy can be solved by use of a decomposed spectrum. For
the permutation problem, we have proposed the rules in terms of gain
ratio and phase difference derived from the decomposed spectra and
the source-s coarse directions.
The present paper experimentally clarifies that the gain ratio and
the phase difference work effectively in a real environment but their
performance depends on frequency bands, a microphone-space and
a source-microphone distance. From these facts it is seen that it is
difficult to attain a perfect solution for the permutation problem in a
real environment only by either the gain ratio or the phase difference.
For the perfect solution, this paper gives a solution to the problems
in a real environment. The proposed method is simple, the amount of
calculation is small. And the method has high correction performance
without depending on the frequency bands and distances from source
signals to microphones. Furthermore, it can be applied under the real
environment. From several experiments in a real room, it clarifies
that the proposed method has been verified.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece with copper tools are being optimized
according to its individual machining characteristic i.e. material
removal rate (MRR). Lower MRR during EDM machining process
may decrease its- machining productivity. Hence, the quality
characteristic for MRR is set to higher-the-better to achieve the
optimum machining productivity. Taguchi method has been used
for the construction, layout and analysis of the experiment for each
of the machining characteristic for the MRR. The use of Taguchi
method in the experiment saves a lot of time and cost of preparing
and machining the experiment samples. Therefore, an L18
Orthogonal array which was the fundamental component in the
statistical design of experiments has been used to plan the
experiments and Analysis of Variance (ANOVA) is used to
determine the optimum machining parameters for this machining
characteristic. The control parameters selected for this
optimization experiments are polarity, pulse on duration, discharge
current, discharge voltage, machining depth, machining diameter
and dielectric liquid pressure. The result had shown that the higher
the discharge voltage, the higher will be the MRR.
Abstract: In this paper we proposed two new confidence intervals for the normal population mean with known coefficient of variation. This situation occurs normally in environment and agriculture experiments where the scientist knows the coefficient of variation of their experiments. We propose two new confidence intervals for this problem based on the recent work of Searls [5] and the new method proposed in this paper for the first time. We derive analytic expressions for the coverage probability and the expected length of each confidence interval. Monte Carlo simulation will be used to assess the performance of these intervals based on their expected lengths.
Abstract: In this work, the results of mixing study by a jet mixer in a tank have been investigated in the laboratory scale. The tank dimensions are H/D=1 and the jet entrance have been considered in
the center of upper surface of tank. RNG-k-ε model is used as the
turbulent model for the prediction of the pattern of turbulent flow
inside the tank. For this purpose, a tank with volume of 110 liter is
simulated and it has been divided into 410,000 tetrahedral control
cells for performing the calculations. The grids at the vicinity of the
nozzle and suction pare are finer to get more accurate results. The
experimental results showed that in a vertical jet, the lowest mixing
time takes place at 35 degree. In addition, mixing time decreased by
increasing the Reynolds number. Furthermore, the CFD simulation
predicted the items as well a flow patterns precisely that validates the
experiments.
Abstract: A numerical study on the influence of forward-facing
cavity length upon forward-facing cavity and opposing jet combined
thermal protection system (TPS) cooling efficiency under hypersonic
flow is conducted, by means of which the flow field parameters, heat
flux distribution along the outer body surface are obtained. The
numerical simulation results are validated by experiments and the
cooling effect of the combined TPS with different cavity length is
analyzed. The numerical results show that the combined configuration
dose well in cooling the nose of the hypersonic vehicle. The deeper the
cavity is, the weaker the heat flux is. The recirculation region plays a
key role for the reduction of the aerodynamic heating.
Abstract: The induction hardening machines are utilized in
the industries which modify machine parts and tools needed to
achieve high ware resistance. This paper describes the model of
induction heating process design of inverter circuit and the results
of induction surface hardening of heating coil. In the design of
heating coil, the shape and the turn numbers of the coil are very
important design factors because they decide the overall operating
performance of induction heater including resonant frequency, Q
factor, efficiency and power factor. The performance will be tested
by experiments in some cases high frequency induction hardening
machine.
Abstract: In this study, a new criterion for determining the number of classes an image should be segmented is proposed. This criterion is based on discriminant analysis for measuring the separability among the segmented classes of pixels. Based on the new discriminant criterion, two algorithms for recursively segmenting the image into determined number of classes are proposed. The proposed methods can automatically and correctly segment objects with various illuminations into separated images for further processing. Experiments on the extraction of text strings from complex document images demonstrate the effectiveness of the proposed methods.1
Abstract: Automatic currency note recognition invariably
depends on the currency note characteristics of a particular country
and the extraction of features directly affects the recognition ability.
Sri Lanka has not been involved in any kind of research or
implementation of this kind. The proposed system “SLCRec" comes
up with a solution focusing on minimizing false rejection of notes.
Sri Lankan currency notes undergo severe changes in image quality
in usage. Hence a special linear transformation function is adapted to
wipe out noise patterns from backgrounds without affecting the
notes- characteristic images and re-appear images of interest. The
transformation maps the original gray scale range into a smaller
range of 0 to 125. Applying Edge detection after the transformation
provided better robustness for noise and fair representation of edges
for new and old damaged notes. A three layer back propagation
neural network is presented with the number of edges detected in row
order of the notes and classification is accepted in four classes of
interest which are 100, 500, 1000 and 2000 rupee notes. The
experiments showed good classification results and proved that the
proposed methodology has the capability of separating classes
properly in varying image conditions.
Abstract: A simple model for studying convectional lifting
processes in the tropics is described in this paper with some tests of
the model in dry air. The model consists of the density equation, the
wind equation, the vertical velocity equation, and the temperature
equation. The model domain is two-dimensional with length 100 km
and height 17.5 km. Plan for experiments to investigate the effects of
the heating surface, the deep convection approximation and the
treatment of velocities at the boundaries are discussed. Equations for
the simplified treatment of moisture in the atmosphere in future
numerical experiments are also given.