Abstract: This study examined the effects of eight weeks of
whole-body vibration training (WBVT) on vertical and decuple jump
performance in handball athletes. Sixteen collegiate Level I handball
athletes volunteered for this study. They were divided equally as
control group and experimental group (EG). During the period of the
study, all athletes underwent the same handball specific training, but
the EG received additional WBVT (amplitude: 2 mm, frequency: 20 -
40 Hz) three time per week for eight consecutive weeks. The vertical
jump performance was evaluated according to the maximum height of
squat jump (SJ) and countermovement jump (CMJ). Single factor
ANCOVA was used to examine the differences in each parameter
between the groups after training with the pretest values as a covariate.
The statistic significance was set at p < .05. After 8 weeks WBVT, the
EG had significantly improved the maximal height of SJ (40.92 ± 2.96
cm vs. 48.40 ± 4.70 cm, F = 5.14, p < .05) and the maximal height
CMJ (47.25 ± 7.48 cm vs. 52.20 ± 6.25 cm, F = 5.31, p < .05). 8 weeks
of additional WBVT could improve the vertical and decuple jump
performance in handball athletes. Enhanced motor unit
synchronization and firing rates, facilitated muscular contraction
stretch-shortening cycle, and improved lower extremity
neuromuscular coordination could account for these enhancements.
Abstract: A novel circuit for generating a signal embedded with
features about data from three sensors is presented. This suggested
circuit is making use of a resistance-to-time converter employing a
bridge amplifier, an integrator and a comparator. The second resistive
sensor (Rz) is transformed into duty cycle. Another bridge with
varying resistor, (Ry) in the feedback of an OP AMP is added in
series to change the amplitude of the resulting signal in a proportional
relationship while keeping the same frequency and duty cycle
representing proportional changes in resistors Rx and Rz already
mentioned. The resultant output signal carries three types of
information embedded as variations of its frequency, duty cycle and
amplitude.
Abstract: In this paper we discuss the problems of the long-term management policy of Lake Peipsi and the roles of natural and anthropogenic factors in the ecological state of the lake. The reduction of the pollution during the last 15 years could not give significant changes of the chemical composition of the water, what implicates the essential role that natural factors have on the ecological state of lake. One of the most important factors having impact on the hydrochemical cycles and ecological state is the hydrological regime which is clearly expressed in L. Peipsi. The absence on clear interrelations of climate cycles and nutrients suggest that complex abiotic and biotic interactions, which take place in the lake ecosystem, plays a significant role in the matter circulation mechanism within lake.
Abstract: Modeling of a manufacturing system enables one to
identify the effects of key design parameters on the system performance and as a result to make correct decision. This paper
proposes a manufacturing system modeling approach using a spreadsheet model based on queuing network theory, in which a
static capacity planning model and stochastic queuing model are integrated. The model was used to improve the existing system utilization in relation to product design. The model incorporates few
parameters such as utilization, cycle time, throughput, and batch size.
The study also showed that the validity of developed model is good enough to apply and the maximum value of relative error is 10%, far
below the limit value 32%. Therefore, the model developed in this
study is a valuable alternative model in evaluating a manufacturing system
Abstract: We succeeded to produce a high performance and flexible graphene/Manganese dioxide (G/MnO2) electrode coated on flexible polyethylene terephthalate (PET) substrate. The graphene film is initially synthesized by drop-casting the graphene oxide (GO) solution on the PET substrate, followed by simultaneous reduction and patterning of the dried film using carbon dioxide (CO2) laser beam with power of 1.8 W. Potentiostatic Anodic Deposition method was used to deposit thin film of MnO2 with different loading mass 10 – 50 and 100 μg.cm-2 on the pre-prepared graphene film. The electrodes were fully characterized in terms of structure, morphology, and electrochemical performance. A maximum specific capacitance of 973 F.g-1 was attributed when depositing 50μg.cm-2 MnO2 on the laser reduced graphene oxide rGO (or G/50MnO2) and over 92% of its initial capacitance was retained after 1000 cycles. The good electrochemical performance and long-term cycling stability make our proposed approach a promising candidate in the supercapacitor applications.
Abstract: The relationship between tropical cyclogenesis and solar activity is addressed in this paper, analyzing the relationship between important parameters in the evolution of tropical cyclones as the CAPE, wind shear and relative vorticity, and the Dst geomagnetic index as a parameter of solar activity. The apparent relationship between all this phenomena has a different response depending on the phase of the solar cycles.
Abstract: This article is an extension and a practical application
approach of Wheeler-s NEBIC theory (Net Enabled Business
Innovation Cycle). NEBIC theory is a new approach in IS research
and can be used for dynamic environment related to new technology.
Firms can follow the market changes rapidly with support of the IT
resources. Flexible firms adapt their market strategies, and respond
more quickly to customers changing behaviors. When every leading
firm in an industry has access to the same IT resources, the way that
these IT resources are managed will determine the competitive
advantages or disadvantages of firm. From Dynamic Capabilities
Perspective and from newly introduced NEBIC theory by Wheeler,
we know that only IT resources cannot deliver customer value but
good configuration of those resources can guarantee customer value
by choosing the right emerging technology, grasping the right
economic opportunities through business innovation and growth. We
found evidences in literature that SOA (Service Oriented
Architecture) is a promising emerging technology which can deliver
the desired economic opportunity through modularity, flexibility and
loose-coupling. SOA can also help firms to connect in network which
can open a new window of opportunity to collaborate in innovation
and right kind of outsourcing. There are many articles and research
reports indicates that failure rate in outsourcing is very high but at the
same time research indicates that successful outsourcing projects
adds tangible and intangible benefits to the service consumer.
Business executives and policy makers in the west should not afraid
of outsourcing but they should choose the right strategy through the
use of emerging technology to significantly reduce the failure rate in
outsourcing.
Abstract: This study describes a capillary-based device
integrated with the heating and cooling modules for polymerase chain
reaction (PCR). The device consists of the reaction
polytetrafluoroethylene (PTFE) capillary, the aluminum blocks, and is
equipped with two cartridge heaters, a thermoelectric (TE) cooler, a
fan, and some thermocouples for temperature control. The cartridge
heaters are placed into the heating blocks and maintained at two
different temperatures to achieve the denaturation and the extension
step. Some thermocouples inserted into the capillary are used to obtain
the transient temperature profiles of the reaction sample during
thermal cycles. A 483-bp DNA template is amplified successfully in
the designed system and the traditional thermal cycler. This work
should be interesting to persons involved in the high-temperature
based reactions and genomics or cell analysis.
Abstract: Design of Converter transformer insulation is a major
challenge. The insulation of these transformers is stressed by both
AC and DC voltages. Particle contamination is one of the major
problems in insulation structures, as they generate partial discharges
leading it to major failure of insulation. Similarly corona discharges
occur in transformer insulation. This partial discharge due to particle
movement / corona formation in insulation structure under different
voltage wave shapes, are different. In the present study, UHF
technique is adopted to understand the discharge activity and could
be realized that the characteristics of UHF signal generated under
low and high fields are different. In the case of corona generated
signal, the frequency content of the UHF sensor output lies in the
range 0.3-1.2 GHz and is not much varied except for its increase in
magnitude of discharge with the increase in applied voltage. It is
realized that the current signal injected due to partial
discharges/corona is about 4ns duration measured for first one half
cycle. Wavelet technique is adopted in the present study. It allows
one to identify the frequency content present in the signal at different
instant of time. The STD-MRA analysis helps one to identify the
frequency band in which the energy content of the UHF signal is
maximum.
Abstract: Solid oxide fuel cells have been considered in the last years as one of the most promising technologies for very highefficiency electric energy generation from hydrogen or other hydrocarbons, both with simple fuel cell plants and with integrated gas turbine-fuel cell systems. In the present study, a detailed thermodynamic analysis has been carried out. Mass and exergy balances are performed not only for the whole plant but also for each component in order to evaluate the thermal efficiency of combined cycle. Moreover, different sources of irreversibilities within the SOFC stack have been discussed and a parametric study conducted to evaluate the effect of temperature as well as pressure on SOFC irreversibilities and its performance. In this investigation methane and hydrogen have been used for fueling the SOFC stack and combustion chamber.
Abstract: The Taiwan government has invested approximately
21 billion NT dollars in the construction of bicycle paths since
bicycling has gained huge popularity as a healthy leisure and
recreational activity. This study focuses on the behavior of
recreational bicyclists in Danshuei and Bali, northern Taiwan. Data
were collected from a field investigation carried out along the
Danshuei bicycle path and Bali left-bank bicycle path. A total of 578
questionnaires were gathered for data analysis. Descriptive statistics
and Chi-Square tests were used to assess bicyclists- behaviors. The
frequency shows that, in these areas, Danshuei and Bali, most
bicyclists rented bicycles, rode the bicycle path in the afternoon for
about 2 hours. The used the bicycle path one time per week. For most,
it was the first time to ride these bicycle paths. There were significant
differences in distribution of bicycle ownership, time of day, duration
of ride, ride frequency, and whether riding occurred on weekdays or
weekends. Results indicated that most bicyclists in Danshuei and Bali
were infrequent users.
Abstract: IEEE 802.15.4a impulse radio-time hopping ultra wide
band (IR-TH UWB) physical layer, due to small duty cycle and very
short pulse widths is robust against multipath propagation. However,
scattering and reflections with the large number of obstacles in indoor
channel environments, give rise to dense multipath fading. It imposes
serious problem to optimum Rake receiver architectures, for which
very large number of fingers are needed. Presence of strong noise
also affects the reception of fine pulses having extremely low power
spectral density. A robust SRake receiver for IEEE 802.15.4a IRTH
UWB in dense multipath and additive white Gaussian noise
(AWGN) is proposed to efficiently recover the weak signals with
much reduced complexity. It adaptively increases the signal to noise
(SNR) by decreasing noise through a recursive least square (RLS)
algorithm. For simulation, dense multipath environment of IEEE
802.15.4a industrial non line of sight (NLOS) is employed. The power
delay profile (PDF) and the cumulative distribution function (CDF)
for the respective channel environment are found. Moreover, the error
performance of the proposed architecture is evaluated in comparison
with conventional SRake and AWGN correlation receivers. The
simulation results indicate a substantial performance improvement
with very less number of Rake fingers.
Abstract: Let G be a Hamiltonian graph. A factor F of G is called
a Hamiltonian factor if F contains a Hamiltonian cycle. In this paper,
two sufficient conditions are given, which are two neighborhood
conditions for a Hamiltonian graph G to have a Hamiltonian factor.
Abstract: Recordings from recent earthquakes have provided evidence that ground motions in the near field of a rupturing fault differ from ordinary ground motions, as they can contain a large energy, or “directivity" pulse. This pulse can cause considerable damage during an earthquake, especially to structures with natural periods close to those of the pulse. Failures of modern engineered structures observed within the near-fault region in recent earthquakes have revealed the vulnerability of existing RC buildings against pulse-type ground motions. This may be due to the fact that these modern structures had been designed primarily using the design spectra of available standards, which have been developed using stochastic processes with relatively long duration that characterizes more distant ground motions. Many recently designed and constructed buildings may therefore require strengthening in order to perform well when subjected to near-fault ground motions. Fiber Reinforced Polymers are considered to be a viable alternative, due to their relatively easy and quick installation, low life cycle costs and zero maintenance requirements. The objective of this paper is to investigate the adequacy of Artificial Neural Networks (ANN) to determine the three dimensional dynamic response of FRP strengthened RC buildings under the near-fault ground motions. For this purpose, one ANN model is proposed to estimate the base shear force, base bending moments and roof displacement of buildings in two directions. A training set of 168 and a validation set of 21 buildings are produced from FEA analysis results of the dynamic response of RC buildings under the near-fault earthquakes. It is demonstrated that the neural network based approach is highly successful in determining the response.
Abstract: Decision Support System (DSS) are interactive
software systems that are built to assist the management of an
organization in the decision making process when faced with nonroutine
problems in a specific application domain. Non-functional
requirements (NFRs) for a DSS deal with the desirable qualities and
restrictions that the DSS functionalities must satisfy. Unlike the
functional requirements, which are tangible functionalities provided
by the DSS, NFRs are often hidden and transparent to DSS users but
affect the quality of the provided functionalities. NFRs are often
overlooked or added later to the system in an ad hoc manner, leading
to a poor overall quality of the system. In this paper, we discuss the
development of NFRs as part of the requirements engineering phase
of the system development life cycle of DSSs. To help eliciting
NFRs, we provide a comprehensive taxonomy of NFRs for DSSs.
Abstract: Microwave energy can be used for drying purpose. It is unique process. It is distinctly different from conventional drying process. It is advantageous over conventional drying / heating processes. When microwave energy is used for drying purpose, the process can be accelerated with a better control to achieve uniform heating, more conversion efficiency, selective drying and ultimately improved product quality of the output. Also, less floor space and compact system are the added advantages. Existing low power microwave drying system is to be modified with suitable applicator. Appropriate sensors are to be used to measure parameters like moisture, temperature, weight of sample. Suitable high tech controller is to be used to control microwave power continuously from minimum to maximum. Phase - controller, cycle - controller and PWM - controller are some of the advanced power control techniques. It has been proposed to work on turmeric using high-tech phase controller to control the microwave power conveniently. The drying of turmeric with microwave energy employing phase controller gives better results as formulated in this paper and hence new approach of processing turmeric will open future doors of profit making to allied industries and the farmers.
Abstract: Grazing and pastoral overloading through human factors result in significant land desertification. Failure to take into account the phenomenon of desertification as a serious problem can lead to an environmental disaster because of the damages caused by land encroachment. Therefore, soil on residential and urban areas is affected because of the deterioration of vegetation. Overgrazing or grazing in open and irregular lands is practiced in these areas almost throughout the year, especially during the growth cycle of edible plants, thereby leading to their disappearance. In addition, the large number of livestock in these areas exceeds the capacity of these pastures because of pastoral land overloading, which results in deterioration and desertification in the region. In addition, rare plants, the extinction of some edible plants in the region, and the emergence of plants unsuitable for grazing, must be taken into consideration, as along with the emergence of dust and sand storms during the dry seasons (summer to autumn) due to the degradation of vegetation. These results show that strategic plans and regulations that protect the environment from desertification must be developed. Therefore, increased pastoral load is a key human factor in the deterioration of vegetation cover, leading to land desertification in this region.
Abstract: As the resources for naturally occurring aggregates
diminished at an ever increasing rate, researchers are keen to utilize
recycled materials in road construction in harmony with sustainable
development. Steel slag, a waste product from the steel making
industry, is one of the recycled materials reported to exhibit great
potential to replace naturally occurring aggregates in asphalt
mixtures. This paper presents the resilient modulus properties of
steel slag asphalt mixtures subjected to short term oven ageing
(STOA). The resilient modulus test was carried out to evaluate the
stiffness of asphalt mixtures at 10ºC, 25ºC and 40ºC. Previous
studies showed that stiffness changes in asphalt mixture played an
important role in inflicting pavement distress particularly cracking
and rutting that are common at low and high temperatures
respectively. Temperature was found to significantly influence the
resilient modulus of asphalt mixes. The resilient modulus of the
asphalt specimens tested decreased by more than 90% when the test
temperature increased from 10°C to 40°C.
Abstract: A unique combination of adsorption and
electrochemical regeneration with a proprietary adsorbent material
called Nyex 100 was introduced at the University of Manchester for
waste water treatment applications. Nyex 100 is based on graphite
intercalation compound. It is non porous and electrically conducing
adsorbent material. This material exhibited very small BET surface
area i.e. 2.75 m2g-1, in consequence, small adsorptive capacities for
the adsorption of various organic pollutants were obtained. This work
aims to develop composite adsorbent material essentially capable of
electrochemical regeneration coupled with improved adsorption
characteristics. An organic dye, acid violet 17 was used as standard
organic pollutant. The developed composite material was
successfully electrochemically regenerated using a DC current of 1 A
for 60 minutes. Regeneration efficiency was maintained at around
100% for five adsorption-regeneration cycles.
Abstract: Manganese steel (Hadfield) is one of the important
alloys in industry due to its special properties. High work hardening
ability with appropriate toughness and ductility are the properties that
caused this alloy to be used in wear resistance parts and in high
strength condition. Heat treatment is the main process through which
the desired mechanical properties and microstructures are obtained in
Hadfield steel. In this study various heat treatment cycles, differing in
austenising temperature, time and quenching solution are applied. For
this purpose, the same samples of manganese steel was heat treated in
9 different cycles, and then the mechanical properties and
microstructures were investigated. Based on the results of the study,
the optimum heat treatment cycle was obtained.