Abstract: Aggressive scaling of MOS devices requires use of ultra-thin gate oxides to maintain a reasonable short channel effect and to take the advantage of higher density, high speed, lower cost etc. Such thin oxides give rise to high electric fields, resulting in considerable gate tunneling current through gate oxide in nano regime. Consequently, accurate analysis of gate tunneling current is very important especially in context of low power application. In this paper, a simple and efficient analytical model has been developed for channel and source/drain overlap region gate tunneling current through ultra thin gate oxide n-channel MOSFET with inevitable deep submicron effect (DSME).The results obtained have been verified with simulated and reported experimental results for the purpose of validation. It is shown that the calculated tunnel current is well fitted to the measured one over the entire oxide thickness range. The proposed model is suitable enough to be used in circuit simulator due to its simplicity. It is observed that neglecting deep sub-micron effect may lead to large error in the calculated gate tunneling current. It is found that temperature has almost negligible effect on gate tunneling current. It is also reported that gate tunneling current reduces with the increase of gate oxide thickness. The impact of source/drain overlap length is also assessed on gate tunneling current.
Abstract: We propose a new approach on how to obtain the approximate solutions of Hamilton-Jacobi (HJ) equations. The process of the approximation consists of two steps. The first step is to transform the HJ equations into the virtual time based HJ equations (VT-HJ) by introducing a new idea of ‘virtual-time’. The second step is to construct the approximate solutions of the HJ equations through a computationally iterative procedure based on the VT-HJ equations. It should be noted that the approximate feedback solutions evolve by themselves as the virtual-time goes by. Finally, we demonstrate the effectiveness of our approximation approach by means of simulations with linear and nonlinear control problems.
Abstract: The problem of lot sizing, sequencing and scheduling
multiple products in flow line production systems has been studied
by several authors. Almost all of the researches in this area assumed
that setup times and costs are sequence –independent even though
sequence dependent setups are common in practice. In this paper we
present a new mixed integer non linear program (MINLP) and a
heuristic method to solve the problem in sequence dependent case.
Furthermore, a genetic algorithm has been developed which applies
this constructive heuristic to generate initial population. These two
proposed solution methods are compared on randomly generated
problems. Computational results show a clear superiority of our
proposed GA for majority of the test problems.
Abstract: Bus Rapid Transit (BRT) has emerged as a cost-effective transport system for urban mobility. However its ability to stimulate land development remains largely unexplored. The study makes use of qualitative (interview method) and quantitative analysis (questionnaire survey and longitudinal analysis of property data) to investigate land development impact resulting from BRT in Beijing, China. The empirical analysis suggests that BRT has a positive impact on the residential and commercial property attractiveness along the busway corridor. The statistical analysis suggests that accessibility advantage conferred by BRT is capitalized into higher property price. The average price of apartments adjacent to a BRT station has gained a relatively faster increase than those not served by the BRT system. The capitalization effect mostly occurs after the full operation of BRT, and is more evident over time and particularly observed in areas which previously lack alternative mobility opportunity.
Abstract: So much energy is used in high rise buildings to fulfill
the basic needs of users such as lighting and thermal comfort.
Malaysia has hot and humid climate, buildings especially high rise
buildings receive unnecessary solar radiation that cause more solar
heat gain. Energy use specially electricity consumption in high rise
buildings has increased. There have been growing concerns about
energy consumption and its effect on environment. Building, energy
and the environment are important issues that the designers should
consider to them. Self protected form is one of possible ways against
the impact of solar radiation in high rise buildings. The Energy
performance of building envelopes was investigated in term of the
Overall Thermal Transfer Value (OTTV ).In this paper, the amount
of OTTV reduction was calculated through OTTV Equations to
clear the effectiveness of self shading strategy on minimizing energy
consumption for cooling interior spaces in high rise buildings which
has considerable envelope areas against solar radiation. Also increasing
the optimum window area was investigated using self-shading
strategy in designing high rise buildings. As result, the significant
reduction in OTTV was shown based on WWR.In addition slight
increase was demonstrated in WWR that can influence on visible
comfort interior spaces.
Abstract: Today-s healthcare industries had become more
patient-centric than profession-centric, from which the issues of quality of healthcare and the patient safety are the major concerns in the modern healthcare facilities. An unplanned extubation (UE) may
be detrimental to the patient-s life, and thus is one of the major indexes
of patient safety and healthcare quality. A high UE rate not only
defeated the healthcare quality as well as the patient safety policy but
also the nurses- morality, and job satisfaction. The UE problem in a psychiatric hospital is unique and may be a tough challenge for the
healthcare professionals for the patients were mostly lacking communication capabilities. We reported with this essay a particular
project that was organized to reduce the UE rate from the current 2.3%
to a lower and satisfactory level in the long-term care units of a psychiatric hospital. The project was conducted between March 1st,
2011 and August 31st, 2011. Based on the error information gathered
from varied units of the hospital, the team analyzed the root causes
with possible solutions proposed to the meetings. Four solutions were
then concluded with consensus and launched to the units in question.
The UE rate was now reduced to a level of 0.17%. Experience from
this project, the procedure and the tools adopted would be good reference to other hospitals.
Abstract: An effort has been taken to simulate the combustion
and performance characteristics of biodiesel fuel in direct injection
(D.I) low heat rejection (LHR) diesel engine. Comprehensive
analyses on combustion characteristics such as cylinder pressure,
peak cylinder pressure, heat release and performance characteristics
such as specific fuel consumption and brake thermal efficiency are
carried out. Compression ignition (C.I) engine cycle simulation was
developed and modified in to LHR engine for both diesel and
biodiesel fuel. On the basis of first law of thermodynamics the
properties at each degree crank angle was calculated. Preparation and
reaction rate model was used to calculate the instantaneous heat
release rate. A gas-wall heat transfer calculations are based on the
ANNAND-s combined heat transfer model with instantaneous wall
temperature to analyze the effect of coating on heat transfer. The
simulated results are validated by conducting the experiments on the
test engine under identical operating condition on a turbocharged D.I
diesel engine. In this analysis 20% of biodiesel (derived from
Jatropha oil) blended with diesel and used in both conventional and
LHR engine. The simulated combustion and performance
characteristics results are found satisfactory with the experimental
value.
Abstract: A numerical study of flow in a horizontally channel
partially filled with a porous screen with non-uniform inlet has been
performed by lattice Boltzmann method (LBM). The flow in porous
layer has been simulated by the Brinkman-Forchheimer model.
Numerical solutions have been obtained for variable porosity models
and the effects of Darcy number and porosity have been studied in
detail. It is found that the flow stabilization is reliant on the Darcy
number. Also the results show that the stabilization of flow field and
heat transfer is depended to Darcy number. Distribution of stream
field becomes more stable by decreasing Darcy number. Results
illustrate that the effect of variable porosity is significant just in the
region of the solid boundary. In addition, difference between constant
and variable porosity models is decreased by decreasing the Darcy
number.
Abstract: Numerical parametric study is conducted to study the effects of ampoule rotation on the flows and the dopant segregation in vertical bridgman (vb) crystal growth. Calculations were performed in unsteady state. The extended darcy model, which includes the time derivative and coriolis terms, has been employed in the momentum equation. It’s found that the convection, and dopant segregation can be affected significantly by ampoule rotation, and the effect is similar to that by an axial magnetic field. Ampoule rotation decreases the intensity of convection and stretches the flow cell axially. When the convection is weak, the flow can be suppressed almost completely by moderate ampoule rotation and the dopant segregation becomes diffusion-controlled. For stronger convection, the elongated flow cell by ampoule rotation may bring dopant mixing into the bulk melt reducing axial segregation at the early stage of the growth. However, if the cellular flow cannot be suppressed completely, ampoule rotation may induce larger radial segregation due to poor mixing.
Abstract: The Helmholtz equation often arises in the study of physical problems involving partial differential equation. Many researchers have proposed numerous methods to find the analytic or approximate solutions for the proposed problems. In this work, the exact analytical solutions of the Helmholtz equation in spherical polar coordinates are presented using the Nikiforov-Uvarov (NU) method. It is found that the solution of the angular eigenfunction can be expressed by the associated-Legendre polynomial and radial eigenfunctions are obtained in terms of the Laguerre polynomials. The special case for k=0, which corresponds to the Laplace equation is also presented.
Abstract: This paper To get the angle value with a MEMS rate
gyroscope in some specific field, the usual method is to make an
integral operation to the rate output, which will lead the error
cumulating effect. So the rate gyro is not suitable. MEMS rate
integrating gyroscope (MRIG) will solve this problem. A DSP system
has been developed to implement the control arithmetic. The system
can measure the angle of rotation directly by the control loops that
make the sensor work in whole-angle mode. Modeling the system with
MATLAB, desirable results of angle outputs are got, which prove the
feasibility of the control arithmetic.
Abstract: In this paper as showed a non-invasive 3D eye tracker
for optometry clinical applications. Measurements of biomechanical
variables in clinical practice have many font of errors associated with
traditional procedments such cover test (CT), near point of
accommodation (NPC), eye ductions (ED), eye vergences (EG) and,
eye versions (ES). Ocular motility should always be tested but all
evaluations have a subjective interpretations by practitioners, the
results is based in clinical experiences, repeatability and accuracy
don-t exist. Optometric-lab is a tool with 3 (tree) analogical video
cameras triggered and synchronized in one acquisition board AD.
The variables globe rotation angle and velocity can be quantified.
Data record frequency was performed with 27Hz, camera calibration
was performed in a know volume and image radial distortion
adjustments.
Abstract: Electro-hydraulic power steering (EHPS) system for
the fuel rate reduction and steering feel improvement is comprised of
ECU including the logic which controls the steering system and BL
DC motor and produces the best suited cornering force, BLDC motor,
high pressure pump integrated module and basic oil-hydraulic circuit
of the commercial HPS system.
Electro-hydraulic system can be studied in two ways such as
experimental and computer simulation. To get accurate results in
experimental study of EHPS system, the real boundary management is
necessary which is difficult task. And the accuracy of the experimental
results depends on the preparation of the experimental setup and
accuracy of the data collection. The computer simulation gives
accurate and reliable results if the simulation is carried out considering
proper boundary conditions. So, in this paper, each component of
EHPS was modeled, and the model-based analysis and control logic
was designed by using AMESim
Abstract: Alkali Activated Slag Concrete (AASC) mixes are manufactured by activating ground granulated blast furnace slag (GGBFS) using sodium hydroxide and sodium silicate solutions. The aim of the present experimental research was to investigate the effect of increasing the dosages of sodium oxide (Na2O, in the range of 4 to 8%) and the activator modulus (Ms) (i.e. the SiO2/Na2O ratio, in the range of 0.5 to 1.5) of the alkaline solutions, on the workability and strength characteristics of self-cured (air-cured) alkali activated Indian slag concrete mixes. Further the split tensile and flexure strengths for optimal mixes were studied for each dosage of Na2O.It is observed that increase in Na2O concentration increases the compressive, split-tensile and flexural strengths, both at the early and later-ages, while increase in Ms, decreases the workability of the mixes. An optimal Ms of 1.25 is found at various Na2O dosages. No significant differences in the strength performances were observed between AASCs manufactured with alkali solutions prepared using either of potable and de-ionized water.
Abstract: Parametric models have been quite popular for
studying human growth, particularly in relation to biological
parameters such as peak size velocity and age at peak size velocity.
Longitudinal data are generally considered to be vital for fittinga
parametric model to individual-specific data, and for studying the
distribution of these biological parameters in a human population.
However, cross-sectional data are easier to obtain than longitudinal
data. In this paper, we present a method of combining longitudinal
and cross-sectional data for the purpose of estimating the distribution
of the biological parameters. We demonstrate, through simulations in
the special case ofthePreece Baines model, how estimates based on
longitudinal data can be improved upon by harnessing the
information contained in cross-sectional data.We study the extent of
improvement for different mixes of the two types of data, and finally
illustrate the use of the method through data collected by the Indian
Statistical Institute.
Abstract: Industrial robots play a vital role in automation
however only little effort are taken for the application of robots in
machining work such as Grinding, Cutting, Milling, Drilling,
Polishing etc. Robot parallel manipulators have high stiffness,
rigidity and accuracy, which cannot be provided by conventional
serial robot manipulators. The aim of this paper is to perform the
modeling and the workspace analysis of a 3 DOF Parallel
Manipulator (3 DOF PM). The 3 DOF PM was modeled and
simulated using 'ADAMS'. The concept involved is based on the
transformation of motion from a screw joint to a spherical joint
through a connecting link. This paper work has been planned to
model the Parallel Manipulator (PM) using screw joints for very
accurate positioning. A workspace analysis has been done for the
determination of work volume of the 3 DOF PM. The position of the
spherical joints connected to the moving platform and the
circumferential points of the moving platform were considered for
finding the workspace. After the simulation, the position of the joints
of the moving platform was noted with respect to simulation time and
these points were given as input to the 'MATLAB' for getting the
work envelope. Then 'AUTOCAD' is used for determining the work
volume. The obtained values were compared with analytical
approach by using Pappus-Guldinus Theorem. The analysis had been
dealt by considering the parameters, link length and radius of the
moving platform. From the results it is found that the radius of
moving platform is directly proportional to the work volume for a
constant link length and the link length is also directly proportional
to the work volume, at a constant radius of the moving platform.
Abstract: Optimum communication and performance in
Wireless Sensor Networks, constitute multi-facet challenges due to
the specific networking characteristics as well as the scarce resource
availability. Furthermore, it is becoming increasingly apparent that
isolated layer based approaches often do not meet the demands posed
by WSNs applications due to omission of critical inter-layer
interactions and dependencies. As a counterpart, cross-layer is
receiving high interest aiming to exploit these interactions and
increase network performance. However, in order to clearly identify
existing dependencies, comprehensive performance studies are
required evaluating the effect of different critical network parameters
on system level performance and behavior.This paper-s main
objective is to address the need for multi-parametric performance
evaluations considering critical network parameters using a well
known network simulator, offering useful and practical conclusions
and guidelines. The results reveal strong dependencies among
considered parameters which can be utilized by and drive future
research efforts, towards designing and implementing highly efficient
protocols and architectures.
Abstract: This paper proposes a low-voltage and low-power
fully integrated digitally tuned continuous-time channel selection
filter for WiMAX applications. A 5th-order elliptic low-pass filter is
realized in a Gm-C topology. The bandwidth of the fully differential
filter is reconfigurable from 2.5MHz to 20MHz (8x) for different
requirements in WiMAX applications. The filter is simulated in a
standard 90nm CMOS process. Simulation results show the THD
(@Vout =100mVpp) is less than -66dB. The in-band ripple of the
filter is about 0.15dB. The filter consumes 1.5mW from a supply
voltage of 0.9V.
Abstract: Occurrences of spurious crests on the troughs of large,
relatively steep second-order Stokes waves are anomalous and not an
inherent characteristic of real waves. Here, the effects of such
occurrences on the statistics described by the standard second-order
stochastic model are examined theoretically and by way of
simulations. Theoretical results and simulations indicate that when
spurious occurrences are sufficiently large, the standard model leads
to physically unrealistic surface features and inaccuracies in the
statistics of various surface features, in particular, the troughs and
thus zero-crossing heights of large waves. Whereas inaccuracies can
be fairly noticeable for long-crested waves in both deep and
shallower depths, they tend to become relatively insignificant in
directional waves.
Abstract: In the context of large volume Big Divisor (nearly)
SLagy D3/D7 μ-Split SUSY [1], after an explicit identification
of first generation of SM leptons and quarks with fermionic superpartners
of four Wilson line moduli, we discuss the identification of
gravitino as a potential dark matter candidate by explicitly calculating
the decay life times of gravitino (LSP) to be greater than age of
universe and lifetimes of decays of the co-NLSPs (the first generation
squark/slepton and a neutralino) to the LSP (the gravitino) to be
very small to respect BBN constraints. Interested in non-thermal
production mechanism of gravitino, we evaluate the relic abundance
of gravitino LSP in terms of that of the co-NLSP-s by evaluating
their (co-)annihilation cross sections and hence show that the former
satisfies the requirement for a potential Dark Matter candidate. We
also show that it is possible to obtain a 125 GeV light Higgs in our
setup.