Abstract: Studies regarding the determination of population
trend of Lipaphis erysimi (kalt.) and its associated natural enemies in
different Brassica lines along with the effect of gamma radiation on
their population were conducted at Agricultural Research Farm,
Malakandher, Khyber Pakhtunkhwa Agricultural University
Peshawar during spring 2006. Three different Brassica lines F6B3,
F6B6 and F6B7 were used, which were replicated four times in
Randomized Complete Block Design. The data revealed that aphid
infestation invariably stated in all three varieties during last week of
February 2006 (1st observation). The peak population of 4.39 aphids
leaf-1 was s recorded during 2nd week of March and lowest population
of 1.02 aphids leaf-1 was recorded during 5th week of March. The
species of lady bird beetle (Coccinella septempunctata) and Syrphid
fly (Syrphus balteatus) first appeared on 24th February with a mean
number of 0.40 lady bird beetle leaf-1 and 0.87 Syrphid fly leaf-1,
respectively. At the time when aphid population started to increase
the peak population of C. septempunctata (0.70 lady bird beetle leaf-
1) and S. balteatus (1.04 syrphid fly leaf-1) was recorded on the 2nd
week of March. Chrysoperla carnea appeared in the 1st week of
March and their peak population was recorded during the 3rd week of
March with mean population of 1.46 C. carnea leaf-1. Among all the
Brassica lines, F6B7 showed comparatively more resistance as
compared to F6B3 F6B6. F6B3 showed least resistance against L.
erysimi, which was found to be the most susceptible cultivar. F6B7
was also found superior in terms of natural enemies. Maximum
number of all natural enemies was recorded on this variety followed
by F6B6. Lowest number of natural enemies was recorded in F6B3.
No significant effect was recorded for the effect of gamma radiation
on the population of aphids, natural enemies and on the varieties.
Abstract: Timing driven physical design, synthesis, and
optimization tools need efficient closed-form delay models for
estimating the delay associated with each net in an integrated circuit
(IC) design. The total number of nets in a modern IC design has
increased dramatically and exceeded millions. Therefore efficient
modeling of interconnection is needed for high speed IC-s. This
paper presents closed–form expressions for RC and RLC
interconnection trees in current mode signaling, which can be
implemented in VLSI design tool. These analytical model
expressions can be used for accurate calculation of delay after the
design clock tree has been laid out and the design is fully routed.
Evaluation of these analytical models is several orders of magnitude
faster than simulation using SPICE.
Abstract: Resistance spot welding process comprises of electric,
thermal and mechanical phenomenon, which makes this process
complex and highly non-linear and thus, it becomes difficult to model
it. In order to obtain good weld nugget during spot welding, hit and
trial welds are usually done which is very costly. Therefore the
numerical simulation research has been conducted to understand the
whole process. In this paper three different cases were analyzed by
varying the tip contact area and it was observed that, with the
variation of tip contact area the nugget formation at the faying
surface is affected. The tip contact area of the welding electrode
becomes large with long welding cycles. Therefore in order to
maintain consistency of nugget formation during the welding process,
the current compensation in control feedback is required. If the
contact area of the welding electrode tip is reduced, a large amount of
current flows through the faying surface, as a result of which
sputtering occurs.
Abstract: In high powered dense wavelength division
multiplexed (WDM) systems with low chromatic dispersion,
four-wave mixing (FWM) can prove to be a major source of noise.
The MultiCanonical Monte Carlo Method (MCMC) and the Split
Step Fourier Method (SSFM) are combined to accurately evaluate the
probability density function of the decision variable of a receiver,
limited by FWM. The combination of the two methods leads to more
accurate results, and offers the possibility of adding other optical
noises such as the Amplified Spontaneous Emission (ASE) noise.
Abstract: The aged are faced with increasing risk for falls. The
aged have the easily fragile bones than others. When falls have
occurred, it is important to detect this emergency state because such
events often lead to more serious illness or even death. A
implementation of PDA system, for detection of emergency situation,
was developed using 3-axis accelerometer in this paper as follows.
The signals were acquired from the 3-axis accelerometer, and then
transmitted to the PDA through Bluetooth module. This system can
classify the human activity, and also detect the emergency state like
falls. When the fall occurs, the system generates the alarm on the
PDA. If a subject does not respond to the alarm, the system determines
whether the current situation is an emergency state or not, and then
sends some information to the emergency center in the case of urgent
situation. Three different studies were conducted on 12 experimental
subjects, with results indicating a good accuracy. The first study was
performed to detect the posture change of human daily activity. The
second study was performed to detect the correct direction of fall. The
third study was conducted to check the classification of the daily
physical activity. Each test was lasted at least 1 min. in third study.
The output of acceleration signal was compared and evaluated by
changing a various posture after attaching a 3-axis accelerometer
module on the chest. The newly developed system has some important
features such as portability, convenience and low cost. One of the
main advantages of this system is that it is available at home
healthcare environment. Another important feature lies in low cost to
manufacture device. The implemented system can detect the fall
accurately, so will be widely used in emergency situation.
Abstract: The crystallization kinetics and phase transformation
of SiO2.Al2O3.0,56P2O5.1,8CaO.0,56CaF2 glass have been
investigated using differential thermal analysis (DTA), x-ray
diffraction (XRD), and scanning electron microscopy (SEM). Glass
samples were obtained by melting the glass mixture at 14500С/120
min. in platinum crucibles. The mixture were prepared from
chemically pure reagents: SiO2, Al(OH)3, H3PO4, CaCO3 and CaF2.
The non-isothermal kinetics of crystallization was studied by
applying the DTA measurements carried out at various heating rates.
The activation energies of crystallization and viscous flow were
measured as 348,4 kJ.mol–1 and 479,7 kJ.mol–1 respectively. Value of
Avrami parameter n ≈ 3 correspond to a three dimensional of crystal
growth mechanism. The major crystalline phase determined by XRD
analysis was fluorapatite (Ca(PO4)3F) and as the minor phases –
fluormargarite (CaAl2(Al2SiO2)10F2) and vitlokite (Ca9P6O24). The
resulting glass-ceramic has a homogeneous microstructure, composed
of prismatic crystals, evenly distributed in glass phase.
Abstract: The concentrations of As, Hg, Co, Cr and Cd were
tested for each soil sample, and their spatial patterns were analyzed
by the semivariogram approach of geostatistics and geographical
information system technology. Multivariate statistic approaches
(principal component analysis and cluster analysis) were used to
identify heavy metal sources and their spatial pattern. Principal
component analysis coupled with correlation between heavy metals
showed that primary inputs of As, Hg and Cd were due to
anthropogenic while, Co, and Cr were associated with pedogenic
factors. Ordinary kriging was carried out to map the spatial patters of
heavy metals. The high pollution sources evaluated was related with
usage of urban and industrial wastewater. The results of this study
helpful for risk assessment of environmental pollution for decision
making for industrial adjustment and remedy soil pollution.
Abstract: The purpose of this study is to derive parameters
estimating for the Lyman–Kutcher–Burman (LKB) normal tissue
complication probability (NTCP) model using analysis of scintigraphy
assessments and quality of life (QoL) measurement questionnaires for
the parotid gland (xerostomia). In total, 31 patients with
head-and-neck (HN) cancer were enrolled. Salivary excretion factor
(SEF) and EORTC QLQ-H&N35 questionnaires datasets are used for
the NTCP modeling to describe the incidence of grade 4 xerostomia.
Assuming that n= 1, NTCP fitted parameters are given as TD50= 43.6
Gy, m= 0.18 in SEF analysis, and as TD50= 44.1 Gy, m= 0.11 in QoL
measurements, respectively. SEF and QoL datasets can validate the
Quantitative Analyses of Normal Tissue Effects in the Clinic
(QUANTEC) guidelines well, resulting in NPV-s of 100% for the both
datasets and suggests that the QUANTEC 25/20Gy gland-spared
guidelines are suitable for clinical used for the HN cohort to
effectively avoid xerostomia.
Abstract: Bicycle configuration is not as large as those of motorcycles or automobiles, while it indeed composes a complicated dynamic system. People-s requirements on comfortability, controllability and safety grow higher as the research and development technologies improve. The shock absorber affects the vehicle suspension performances enormously. The absorber takes the vibration energy and releases it at a suitable time, keeping the wheel under a proper contact condition with road surface, maintaining the vehicle chassis stability. Suspension design for mountain bicycles is more difficult than that of city bikes since it encounters dynamic variations on road and loading conditions. Riders need a stiff damper as they exert to tread on the pedals when climbing, while a soft damper when they descend downhill. Various switchable shock absorbers are proposed in markets, however riders have to manually switch them among soft, hard and lock positions. This study proposes a novel design of the bicycle shock absorber, which provides automatic smooth tuning of the damping coefficient, from a predetermined lower bound to theoretically unlimited. An automatic quick releasing valve is involved in this design so that it can release the peak pressure when the suspension fork runs into a square-wave type obstacle and prevent the chassis from damage, avoiding the rider skeleton from injury. This design achieves the automatic tuning process by innovative plunger valve and fluidic passage arrangements without any electronic devices. Theoretical modelling of the damper and spring are established in this study. Design parameters of the valves and fluidic passages are determined. Relations between design parameters and shock absorber performances are discussed in this paper. The analytical results give directions to the shock absorber manufacture.
Abstract: Natural gas flow contains undesirable solid particles,
liquid condensation, and/or oil droplets and requires reliable
removing equipment to perform filtration. Recent natural gas
processing applications are demanded compactness and reliability of
process equipment. Since conventional means are sophisticated in
design, poor in efficiency, and continue lacking robust, a supersonic
nozzle has been introduced as an alternative means to meet such
demands.
A 3-D Convergent-Divergent Nozzle is simulated using
commercial Code for pressure ratio (NPR) varies from 1.2 to 2. Six
different shapes of nozzle are numerically examined to illustrate the
position of shock-wave as such spot could be considered as a
benchmark of particle separation. Rectangle, triangle, circular,
elliptical, pentagon, and hexagon nozzles are simulated using Fluent
Code with all have same cross-sectional area.
The simple one-dimensional inviscid theory does not describe the
actual features of fluid flow precisely as it ignores the impact of
nozzle configuration on the flow properties. CFD Simulation results,
however, show that nozzle geometry influences the flow structures
including location of shock wave.
The CFD analysis predicts shock appearance when p01/pa>1.2 for
almost all geometry and locates at the lower area ratio (Ae/At).
Simulation results showed that shock wave in Elliptical nozzle has
the farthest distance from the throat among the others at relatively
small NPR. As NPR increases, hexagon would be the farthest. The
numerical result is compared with available experimental data and
has shown good agreement in terms of shock location and flow
structure.
Abstract: Analysis of reciprocating equipment piston rod leads
to nonlinear elastic-plastic deformation analysis of rod with initial
imperfection under axial dynamic load. In this paper a new and
effective model and analytical formulations are presented to evaluate
dynamic deformation and elastic-plastic stresses of reciprocating
machine piston rod. This new method has capability to account for
geometric nonlinearity, elastic-plastic deformation and dynamic
effects. Proposed method can be used for evaluation of piston rod
performance for various reciprocating machines under different
operation situations. Rod load curves and maximum allowable rod
load are calculated with presented method for a refinery type
reciprocating compressor. Useful recommendations and guidelines
for rod load, rod load reversal and rod drop monitoring are also
addressed.
Abstract: This paper deals with rheological behavior of tomato
paste from the view point of time independent properties inclusive of
processing variables such as sample temperature which influence on
rheological properties as well as breaking temperature and
concentration which beside the rheological properties, influence on
the quality of final product. With this aim 10 tomato paste samples at
various concentrations (17-25%) and breaking temperatures (65-
85 C o ) have been produced. The experimental results showed tomato
paste behaves as a non-Newtonian semi-fluid which follows power
law model that consistency coefficient (K) is supposed function of
breaking temperature, concentration and sample temperature with
consideration to superimpose function.
Abstract: In order to implement flexibility as well as survivable
capacities over passive optical network (PON), a new automatic
random fault-recovery mechanism with array-waveguide-grating
based (AWG-based) optical switch (OSW) is presented. Firstly,
wavelength-division-multiplexing and optical code-division
multiple-access (WDM/OCDMA) scheme are configured to meet the
various geographical locations requirement between optical network
unit (ONU) and optical line terminal (OLT). The AWG-base optical
switch is designed and viewed as central star-mesh topology to
prohibit/decrease the duplicated redundant elements such as fiber and
transceiver as well. Hence, by simple monitoring and routing switch
algorithm, random fault-recovery capacity is achieved over
bi-directional (up/downstream) WDM/OCDMA scheme. When error
of distribution fiber (DF) takes place or bit-error-rate (BER) is higher
than 10-9 requirement, the primary/slave AWG-based OSW are
adjusted and controlled dynamically to restore the affected ONU
groups via the other working DFs immediately.
Abstract: The work reported in this paper is motivated by the fact that there is a need to apply autonomic computing concepts to parallel computing systems. Advancing on prior work based on intelligent cores [36], a swarm-array computing approach, this paper focuses on 'Intelligent agents' another swarm-array computing approach in which the task to be executed on a parallel computing core is considered as a swarm of autonomous agents. A task is carried to a computing core by carrier agents and is seamlessly transferred between cores in the event of a predicted failure, thereby achieving self-ware objectives of autonomic computing. The feasibility of the proposed swarm-array computing approach is validated on a multi-agent simulator.
Abstract: In the present study, a steady-state simulation model
has been developed to evaluate the system performance of a
transcritical carbon dioxide heat pump system for simultaneous water
cooling and heating. Both the evaporator (including both two-phase
and superheated zone) and gas cooler models consider the highly
variable heat transfer characteristics of CO2 and pressure drop. The
numerical simulation model of transcritical CO2 heat pump has been
validated by test data obtained from experiments on the heat pump
prototype. Comparison between the test results and the model
prediction for system COP variation with compressor discharge
pressure shows a modest agreement with a maximum deviation of
15% and the trends are fairly similar. Comparison for other operating
parameters also shows fairly similar deviation between the test
results and the model prediction. Finally, the simulation results are
presented to study the effects of operating parameters such as,
temperature of heat exchanger fluid at the inlet, discharge pressure,
compressor speed on system performance of CO2 heat pump, suitable
in a dairy plant where simultaneous cooling at 4oC and heating at
73oC are required. Results show that good heat transfer properties of
CO2 for both two-phase and supercritical region and efficient
compression process contribute a lot for high system COPs.
Abstract: Reliable information about tool temperature
distribution is of central importance in metal cutting. In this study,
tool-chip interface temperature was determined in cutting of ST37
steel workpiece by applying HSS as the cutting tool in dry turning.
Two different approaches were implemented for temperature
measuring: an embedded thermocouple (RTD) in to the cutting tool
and infrared (IR) camera. Comparisons are made between
experimental data and results of MSC.SuperForm and FLUENT
software.
An investigation of heat generation in cutting tool was performed
by varying cutting parameters at the stable cutting tool geometry and
results were saved in a computer; then the diagrams of tool
temperature vs. various cutting parameters were obtained. The
experimental results reveal that the main factors of the increasing
cutting temperature are cutting speed (V ), feed rate ( S ) and depth
of cut ( h ), respectively. It was also determined that simultaneously
change in cutting speed and feed rate has the maximum effect on
increasing cutting temperature.
Abstract: The company-s ability to draw on a range of external
sources to meet their needs for innovation, has been termed 'open
innovation' (OI). Very few empirical analyses have been conducted
on Small and Medium Enterprises (SMEs) to the extent that they
describe and understand the characteristics and implications of this
new paradigm.
The study's objective is to identify and characterize different
modes of OI, (considering innovation process phases and the variety
and breadth of the collaboration), determinants, barriers and
motivations in SMEs. Therefore a survey was carried out among
Italian manufacturing firms and a database of 105 companies was
obtained. With regard to data elaboration, a factorial and cluster
analysis has been conducted and three different OI modes have
emerged: selective low open, unselective open upstream, and mid-
partners integrated open. The different behaviours of the three
clusters in terms of determinants factors, performance, firm-s
technology intensity, barriers and motivations have been analyzed
and discussed.
Abstract: Nowadays use of a new structural bracing system
called 'Knee Bracing System' have taken the specialists attention too
much. On the other hand nonlinear static analysis procedures in
estimate structures performance in earthquake time have taken
attention too much. One of these procedure is modal pushover
analysis (MPA) procedure. The accuracy of MPA procedure for
simple steel moment resisting frame has been verified and considered
in Chintanapakdee and Chopra-s article in 2003. Since the accuracy
of MPA procedure has not verified for semi-rigid steel frames with
knee bracing, we are going to get through with this matter in this
study. For this purpose, the selected structures are four frames with
different heights, 5 to 20 stories, will be designed according to AISC
criteria. Then MPA procedure is used for the same frames with
different rigidity percentiles of connections. The results of seismic
responses are compared with dynamic nonlinear response history
analysis as exact procedure and accuracy of MPA procedure is
evaluated. It seems that MPA procedure accuracy will come down by
reduction of the rigidity percentiles of semi-rigid connections.
Abstract: This research work takes a different approach in
the discussion of urban form impacts on transport planning and
auto dependency. Concentrated density represented by effective
density explains auto dependency better than the conventional
density and it is proved to be a realistic density representative for
the urban transportation analysis. Model analysis reveals that
effective density is influenced by the shopping accessibility
index as well as job density factor. It is also combined with the
job access variable to classify four levels of Transport Activity
Centers (TACs) in Okinawa, Japan. Trip attraction capacity and
levels of the newly classified TACs was found agreeable with the
amount of daily trips attracted to each center. The trip attraction
data set was drawn from a 2007 Okinawa personal trip survey.
This research suggests a planning methodology which guides
logical transport supply routes and concentrated local
development schemes.
Abstract: Some physical properties of musk lime (Citrus
microcarpa) were determined in this study. The average moisture
content (wet basis) of the fruit was found to be 85.10 (±0.72) %. The
mean of length, width and thickness of the fruit was 26.36 (±0.97),
26.40 (±1.04) and 25.26 (±0.94) mm respectively. The average value
for geometric mean diameter, sphericity, aspect ratio, mass, surface
area, volume, true density, bulk density and porosity was 26.00
(±0.82) mm, 98.67 (±2.04) %, 100.23 (±3.28) %, 10.007 (±0.878) g,
2125.07 (±133.93) mm2, 8800.00 (±731.82) mm3, 1002.87 (±39.16)
kgm-3, 501.70 (±22.58) kgm-3 and 49.89 (±3.15) % respectively.
The coefficient of static friction on four types of structural surface
was found to be varying from 0.238 (±0.025) for glass to 0.247
(±0.024) for steel surface.