Abstract: This paper present the experimental work of double
unit tunnel form building (TFB) subjected to in-plane lateral cyclic
loading. A one third scale of 3-storey double unit of TFB is tested
until its strength degradation. Then, the TFB is repaired and
retrofitted using additional shear wall, steel angle and CFRP sheet.
The crack patterns, lateral strength, stiffness, ductility and equivalent
viscous damping (EVD) were analyzed and compared before and
after repair and retrofit. The result indicates that the lateral strength
increases by 22% in pushing and 27% in pulling direction. Moreover,
the stiffness and ductility obtained before and after retrofit increase
tremendously by 87.87% and 39.66%, respectively. Meanwhile, the
energy absorption measured by equivalent viscous damping obtained
after retrofit increase by 12.34% in pulling direction. It can be
concluded that the proposed retrofit method is capable to increase the
lateral strength capacity, stiffness and energy absorption of double
unit TFB.
Abstract: The crude oil in an oil well exists in various phases
such as gas, seawater, and sand, as well as oil. Therefore, a phase
separator is needed at the front of a single-phase pump for
pressurization and transfer. On the other hand, the application of a
multiphase pump can provide such advantages as simplification of the
equipment structure and cost savings, because there is no need for a
phase separation process. Therefore, the crude oil transfer method
using a multiphase pump is being applied to recently developed oil
wells. Due to this increase in demand, technical demands for the
development of multiphase pumps are sharply increasing, but the
progress of research into related technologies is insufficient, due to the
nature of multiphase pumps that require high levels of skills. This
study was conducted to verify the reliability of pump performance
evaluation using numerical analysis, which is the basis of the
development of a multiphase pump. For this study, a model was
designed by selecting the specifications of this study. The performance
of the designed model was evaluated through numerical analysis and
experiment. The results of the performance evaluation were compared
to verify the reliability of the result using numerical analysis.
Abstract: Climate change will affect the hydrological cycle in
many different ways such as increase in evaporation and rainfalls.
There have been growing interests among researchers to identify the
nature of trends in historical rainfall data in many different parts of
the world. This paper examines the trends in annual maximum
rainfall data from 30 stations in New South Wales, Australia by using
two non-parametric tests, Mann-Kendall (MK) and Spearman’s Rho
(SR). Rainfall data were analyzed for fifteen different durations
ranging from 6 min to 3 days. It is found that the sub-hourly
durations (6, 12, 18, 24, 30 and 48 minutes) show statistically
significant positive (upward) trends whereas longer duration (subdaily
and daily) events generally show a statistically significant
negative (downward) trend. It is also found that the MK test and SR
test provide notably different results for some rainfall event durations
considered in this study. Since shorter duration sub-hourly rainfall
events show positive trends at many stations, the design rainfall data
based on stationary frequency analysis for these durations need to be
adjusted to account for the impact of climate change. These shorter
durations are more relevant to many urban development projects
based on smaller catchments having a much shorter response time.
Abstract: This paper presents the electromagnetic interference
(EMI) shielding effectiveness of rice husk and carbon nanotubes
(RHCNTs) composites in the X-band region (8.2-12.4 GHz). The
difference weight ratio of carbon nanotubes (CNTs) were mix with
the rice husk. The rectangular waveguide technique was used to
measure the complex permittivity of the RHCNTs composites
materials. The complex permittivity is represented in terms of both
the real and imaginary parts of permittivity in X-band frequency. The
conductivity of RHCNTs shows increasing when the ratio of CNTs
mixture increases. The composites materials were simulated using
Computer Simulation Technology (CST) Microwave Studio
simulation software. The shielding effectiveness of RHCNTs and
pure rice husk was compared. The highest EMI SE of 30 dB is
obtained for RHCNTs composites of 10 wt % CNTs with 10mm
thickness.
Abstract: In structures, stress concentration is a factor of fatigue
fracture. Basically, the stress concentration is a phenomenon that
should be avoided. However, it is difficult to avoid the stress
concentration. Therefore, relaxation of the stress concentration is
important. The stress concentration arises from notches and circular
holes. There is a relaxation method that a composite patch covers a
notch and a circular hole. This relaxation method is used to repair
aerial wings, but it is not systematized. Composites are more
expensive than single materials. Accordingly, we propose the
relaxation method that a single material patch covers a notch and a
circular hole, and aim to systematize this relaxation method.
We performed FEA (Finite Element Analysis) about an object by
using a three-dimensional FEA model. The object was that a patch
adheres to a plate with a circular hole. And, a uniaxial tensile load acts
on the patched plate with a circular hole. In the three-dimensional FEA
model, it is not easy to model the adhesion layer. Basically, the yield
stress of the adhesive is smaller than that of adherents. Accordingly,
the adhesion layer gets to plastic deformation earlier than the adherents
under the yield load of adherents. Therefore, we propose the
three-dimensional FEA model which is applied a nonlinear elastic
region to the adhesion layer. The nonlinear elastic region was
calculated by a bilinear approximation. We compared the analysis
results with the tensile test results to confirm whether the analysis
model has usefulness. As a result, the analysis results agreed with the
tensile test results. And, we confirmed that the analysis model has
usefulness.
As a result that the three-dimensional FEA model was used to the
analysis, it was confirmed that an out-of-plane deformation occurred
to the patched plate with a circular hole. The out-of-plane deformation
causes stress increase of the patched plate with a circular hole.
Therefore, we investigated that the out-of-plane deformation affects
relaxation of the stress concentration in the plate with a circular hole
on this relaxation method. As a result, it was confirmed that the
out-of-plane deformation inhibits relaxation of the stress concentration
on the plate with a circular hole.
Abstract: Supermarkets are the most electricity-intensive type of
commercial buildings. The unsuitable indoor environment of a
supermarket provided by abnormal HVAC operations incurs waste
energy consumption in refrigeration systems. This current study
briefly describes significantly solid backgrounds and proposes easyto-
use analysis terminology for investigating the impact of HVAC
operations on refrigeration power consumption using the field-test
data obtained from building automation system (BAS). With solid
backgrounds and prior knowledge, expected energy interactions
between HVAC and refrigeration systems are proposed through
Pearson’s correlation analysis (R value) by considering correlations
between equipment power consumption and dominantly independent
variables (driving force conditions).The R value can be conveniently
utilized to evaluate how strong relations between equipment
operations and driving force parameters are. The calculated R values
obtained from field data are compared to expected ranges of R values
computed by energy interaction methodology. The comparisons can
separate the operational conditions of equipment into faulty and
normal conditions. This analysis can simply investigate the condition
of equipment operations or building sensors because equipment could
be abnormal conditions due to routine operations or faulty
commissioning processes in field tests. With systematically solid and
easy-to-use backgrounds of interactions provided in the present
article, the procedures can be utilized as a tool to evaluate the proper
commissioning and routine operations of HVAC and refrigeration
systems to detect simple faults (e.g. sensors and driving force
environment of refrigeration systems and equipment set-point) and
optimize power consumption in supermarket buildings. Moreover,
the analysis will be used to further study the FDD research for
supermarkets in future.
Abstract: Due to the large amount of information in the World
Wide Web (WWW, web) and the lengthy and usually linearly
ordered result lists of web search engines that do not indicate
semantic relationships between their entries, the search for topically
similar and related documents can become a tedious task. Especially,
the process of formulating queries with proper terms representing
specific information needs requires much effort from the user. This
problem gets even bigger when the user's knowledge on a subject and
its technical terms is not sufficient enough to do so. This article
presents the new and interactive search application DocAnalyser that
addresses this problem by enabling users to find similar and related
web documents based on automatic query formulation and state-ofthe-
art search word extraction. Additionally, this tool can be used to
track topics across semantically connected web documents.
Abstract: In this paper, we have proposed a parallel IDS and
honeypot based approach to detect and analyze the unknown and
known attack taxonomy for improving the IDS performance and
protecting the network from intruders. The main theme of our
approach is to record and analyze the intruder activities by using both
the low and high interaction honeypots. Our architecture aims to
achieve the required goals by combing signature based IDS,
honeypots and generate the new signatures. The paper describes the
basic component, design and implementation of this approach and
also demonstrates the effectiveness of this approach to reduce the
probability of network attacks.
Abstract: Recently, there have been a lot of earthquakes in Japan.
It is necessary to promote seismic isolation devices for buildings. The
devices have been hardly diffused in attached houses, because the
devices are very expensive. We should develop a low-cost seismic
isolation device for detached houses. We suggested a new seismic
isolation device which uses a two-layer circular tube as a unit. If
hysteresis is produced in the two-layer circular tube under lateral
compression load, we think that the two-layer circular tube can have
energy absorbing capacity. It is necessary to contact the outer layer
and the inner layer to produce hysteresis. We have previously reported
how the inner layer comes in contact with the outer layer from a
perspective of analysis used mechanics of materials. We have clarified
that the inner layer comes in contact with the outer layer under a lateral
compression load. In this paper, we explored contact area between the
outer layer and the inner layer under a lateral compression load by
using FEA. We think that changing the inner layer’s thickness is
effective in increase the contact area. In order to change the inner
layer’s thickness, we changed the shape of the inner layer. As a result,
the contact area changes depending on the inner layer’s thickness.
Additionally, we experimented to check whether hysteresis occurs in
fact. As a consequence, we can reveal hysteresis in the two-layer
circular tube under the condition.
Abstract: This work presents a Computational Fluid Dynamics
(CFD) simulation of a butterfly valve used to control the flow of
combustible gas mixture in an industrial process setting.The work
uses CFD simulation to analyze the flow characteristics in the
vicinity of the valve, including the pressure distributions and
Frequency spectrum of the pressure pulsations downstream the valves
and the vortex shedding allow predicting the torque fluctuations
acting on the valve shaft and the possibility of generating mechanical
vibration and resonance.These fluctuations are due to aerodynamic
torque resulting from fluid turbulence and vortex shedding in the
valve vicinity.
The valve analyzed is located in a pipeline between two opposing
90o elbows, which exposes the valve and the surrounding structure to
the turbulence generated upstream and downstream the elbows at
either end of the pipe.CFD simulations show that the best location for
the valve from a vibration point of view is in the middle of the pipe
joining the elbows.
Abstract: Kigelia africana (Lam.) Benth. (Bignoniaceae) is a
reputed traditional remedy for various human ailments such as skin
diseases, microbial infections, melanoma, stomach troubles,
metabolic disorders, malaria and general pains. In spite of the fruit
being widely used for purposes related to its antibacterial and
antifungal properties, the chemical constituents associated with the
activity have not been fully identified. To elucidate the active
principles, we evaluated the antimicrobial activity of fruit extracts
and purified fractions against Staphylococcus aureus, Enterococcus
faecalis, Moraxella catarrhalis, Escherichia coli, Candida albicans
and Candida tropicalis. Shade-dried fruits were powdered and
extracted with hydroalcoholic (1:1) mixture by soaking at room
temperature for 72 h. The crude extract was further fractionated by
column chromatography, with successive elution using hexane,
dichloromethane, ethyl acetate, acetone and methanol. The
dichloromethane and ethyl acetate fractions were combined and
subjected to column chromatography to furnish a wax and oil from
the eluates of 20% and 40% ethyl acetate in hexane, respectively. The
GC-MS and GC×GC-MS results revealed that linoleic acid, linolenic
acid, palmitic acid, arachidic acid and stearic acid were the major
constituents in both oil and wax. The crude hydroalcoholic extract
exhibited the strongest activity with MICs of 0.125-0.5 mg/mL,
followed by the ethyl acetate (MICs = 0.125-1.0 mg/mL),
dichloromethane (MICs = 0.250-2.0 mg/mL), hexane (MICs = 0.25-
2.0 mg/mL), acetone (MICs = 0.5-2.0 mg/mL) and methanol (MICs =
1.0-2.0 mg/mL), whereas the wax (MICs = 2.0-4.0 mg/mL) and oil
(MICs = 4.0-8.0 mg/mL) showed poor activity. The study concludes
that synergistic interactions of chemical constituents could be
responsible for the antimicrobial activity of K. africana fruits, which
needs a more holistic approach to understand the mechanism of its
antimicrobial activity.
Abstract: In new energy development, wind power has boomed.
It is due to the proliferation of wind parks and their operation in
supplying the national electric grid with low cost and clean resources.
Hence, there is an increased need to establish a proactive
maintenance for wind turbine machines based on remote control and
monitoring. That is necessary with a real-time wireless connection in
offshore or inaccessible locations while the wired method has many
flaws. The objective of this strategy is to prolong wind turbine
lifetime and to increase productivity. The hardware of a remote
control and monitoring system for wind turbine parks is designed. It
takes advantage of GPRS or Wi-Max wireless module to collect data
measurements from different wind machine sensors through IP based
multi-hop communication. Computer simulations with Proteus ISIS
and OPNET software tools have been conducted to evaluate the
performance of the studied system. Study findings show that the
designed device is suitable for application in a wind park.
Abstract: Robotics provides answers to amputees. The most
expensive solutions surgically connect the prosthesis to nerve endings.
There are also several types of non-invasive technologies that recover
nerve messages passing through the muscles. After analyzing these
messages, myoelectric prostheses perform the desired movement.
The main goal is to avoid all surgeries, which can be heavy and offer
cheaper alternatives. For an amputee, we use valid muscles to recover
the electrical signal involved in a muscle movement. EMG sensors
placed on the muscle allows us to measure a potential difference,
which our program transforms into control for a robotic arm with two
degrees of freedom. We have shown the feasibility of non-invasive
prostheses with two degrees of freedom. Signal analysis and an
increase in degrees of freedom is still being improved.
Abstract: The psychological impact of peer influence on its
individual group members, can make them resist HIV/AIDS
counselling and testing. This study investigated the correlate of peer
influence and resistance to HIV/AIDS counselling and testing among
students in tertiary institutions in Kano state, Nigeria. To achieve
this, three null hypotheses were postulated and tested. Cross-
Sectional Survey Design was employed in which 1512 sample was
selected from a student population of 104,841.Simple Random
Sampling was used in the selection. A self-developed 20-item scale
called Peer Influence and Psychological Resistance Inventory
(PIPRI) was used for data collection. Pearson Product Moment
Correlation (PPMCC) via test-retest method was applied to estimate a
reliability coefficient of 0.86 for the scale. Data obtained was
analyzed using t-test and PPMCC at 0.05 level of confidence. Results
reveal 26.3% (397) of the respondents being influenced by their peer
group, while 39.8% showed resistance. Also, the t-tests and PPMCC
statistics were greater than their respective critical values. This shows
that there was a significant gender difference in peer influence and a
difference between peer influence and resistance to HIV/AIDS
counselling and testing. However, a positive relationship between
peer influence and resistance to HIV/AIDS counselling and testing
was shown. A major recommendation offered suggests the use of
reinforcement and social support for positive attitudes and
maintenance of safe behaviour among students who patronize
HIV/AIDS counselling.
Abstract: Cement-based grouts has been used successfully to
repair cracks in many concrete structures such as bridges, tunnels,
buildings and to consolidate soils or rock foundations. In the present
study the rheological characterization of cement grout with
water/binder ratio (W/B) is fixed at 0.5. The effect of the replacement
of cement by bentonite (2 to 10% wt) in presence of superplasticizer
(0.5% wt) was investigated. Several rheological tests were carried out
by using controlled-stress rheometer equipped with vane geometry in
temperature of 20°C. To highlight the influence of bentonite and
superplasticizer on the rheological behavior of grout cement, various
flow tests in a range of shear rate from 0 to 200 s-1 were observed.
Cement grout showed a non-Newtonian viscosity behavior at all
concentrations of bentonite. Three parameter model Herschel-
Bulkley was chosen for fitting of experimental data. Based on the
values of correlation coefficients of the estimated parameters, The
Herschel-Bulkley law model well described the rheological behavior
of the grouts. Test results showed that the dosage of bentonite
increases the viscosity and yield stress of the system and introduces
more thixotropy. While the addition of both bentonite and
superplasticizer with cement grout improve significantly the fluidity
and reduced the yield stress due to the action of dispersion of SP.
Abstract: In order to study the effect of drought stress on grain
yield, yield components and associated traits of durum wheat
cultivars, an experiment was done as split plot arrangement using
randomized complete block design with three replications in Ilam
province, Iran in 2009-2010 cropping season. Different levels of
irrigation (Full irrigation, drought stress at stem elongation,
Flowering and grain formation stages) were considered as a main plot
and three durum wheat cultivars (Yavaros, Seimareh and Karkheh)
were assigned as a sub plot. The results showed that drought stress
was significant on grain yield, spike.m-2, grain. Spike-1, 1000-grain
weight, biological yield, harvest index and protein content. Drought
stress at all stages caused a loss in grain yield and its components.
Full irrigation had the highest grain yield and yield components.
Drought stress at stem elongation, flowering and grain formation
stages caused a reduction in spike.m-2, grain.spike-1 and 1000-grain
weight, respectively. Protein content was significantly affected by
drought stress. The highest protein content was obtained from
drought stress at grain formation stage. Cultivars had an influence on
grain yield and yield components. Yavaros and Seimareh cultivars
had the highest and lowest grain yield, respectively. Interaction effect
between drought stress and cultivar had a significant effect on grain
and yield components. Full irrigation and Yavaros cultivar had the
highest grain yield and drought stress at grain formation stage and
Seimareh cultivar had the lowest grain yield, respectively.
Abstract: The development of the agricultural sector in Ghana
has been reliant on the use of irrigation systems to ensure food
security. However, the manual operation of these systems has not
facilitated their maximum efficiency due to human limitations.
This paper seeks to address this problem by designing and
implementing an efficient, cost effective automated system which
monitors and controls the water flow of irrigation through
communication with an authorized operator via text messages. The
automatic control component of the system is timer based with an
Atmega32 microcontroller and a real time clock from the SM5100B
cellular module. For monitoring purposes, the system sends periodic
notification of the system on the performance of duty via SMS to the
authorized person(s). Moreover, the GSM based Irrigation
Monitoring and Control System saves time and labour and reduces
cost of operating irrigation systems by saving electricity usage and
conserving water.
Field tests conducted have proven its operational efficiency and
ease of assessment of farm irrigation equipment due to its costeffectiveness
and data logging capabilities.
Abstract: Different services based on different switching
techniques in wireless networks leads to drastic changes in the
properties of network traffic. Because of these diversities in services,
network traffic is expected to undergo qualitative and quantitative
variations. Hence, assumption of traffic characteristics and the
prediction of network events become more complex for the wireless
networks. In this paper, the traffic characteristics have been studied
by collecting traces from the mobile switching centre (MSC). The
traces include initiation and termination time, originating node, home
station id, foreign station id. Traffic parameters namely, call interarrival
and holding times were estimated statistically. The results
show that call inter-arrival and distribution time in this wireless
network is heavy-tailed and follow gamma distributions. They are
asymptotically long-range dependent. It is also found that the call
holding times are best fitted with lognormal distribution. Based on
these observations, an analytical model for performance estimation is
also proposed.
Abstract: Renewable energy is derived from natural processes
that are replenished constantly. Included in the definition is
electricity and heat generated from solar, wind, ocean, hydropower,
biomass, geothermal resources, and bio-fuels and hydrogen derived
from renewable resources. Each of these sources has unique
characteristics which influence how and where they are used. This
paper presents the modeling the simulation of solar and hydro hybrid
energy sources in MATLAB/SIMULINK environment. It simulates
all quantities of Hybrid Electrical Power system (HEPS) such as AC
output current of the inverter that injected to the load/grid, load
current, grid current. It also simulates power output from PV and
Hydraulic Turbine Generator (HTG), power delivered to or from grid
and finally power factor of the inverter for PV, HTG and grid. The
proposed circuit uses instantaneous p-q (real-imaginary) power
theory.
Abstract: With advances in solid-state power electronic devices
and microprocessors, various pulse-width-modulation (PWM)
techniques have been developed for industrial applications. This
paper presents the comparison of two different PWM techniques, the
sinusoidal PWM (SPWM) technique and the space-vector PWM
(SVPWM) technique applied to two level VSI for micro grid
applications. These two methods are compared by discussing their
ease of implementation and by analyzing the output harmonic spectra
of various output voltages (line-to-neutral voltages, and line-to-line
voltages) and their total harmonic distortion (THD). The SVPWM
technique in the under-modulation region can increase the
fundamental output voltage by 15.5% over the SPWM technique.