Abstract: Masonry cavity walls are loaded by wind pressure and vertical load from upper floors. These loads results in bending moments and compression forces in the ties connecting the outer and the inner wall in a cavity wall. Large cavity walls are furthermore loaded by differential movements from the temperature gradient between the outer and the inner wall, which results in critical increase of the bending moments in the ties. Since the ties are loaded by combined compression and moment forces, the loadbearing capacity is derived from instability equilibrium equations. Most of them are iterative, since exact instability solutions are complex to derive, not to mention the extra complexity introducing dimensional instability from the temperature gradients. Using an inverse variable substitution and comparing an exact theory with an analytical instability solution a method to design tie-connectors in cavity walls was developed. The method takes into account constraint conditions limiting the free length of the wall tie, and the instability in case of pure compression which gives an optimal load bearing capacity. The model is illustrated with examples from praxis.
Abstract: Polystyrene particles of different sizes are optically
trapped with a gaussian beam from a He-Cd laser operating at 442
nm. The particles are observed to exhibit luminescence after a certain
trapping time followed by an escape from the optical trap. The
observed luminescence is explained in terms of the photodegradation
of the polystyrene backbone. It is speculated that these chemical
modifications also play a role for the escape of the particles from the
trap. Variations of the particle size and the laser power show that
these parameters have a great influence on the observed phenomena.
Abstract: The main focus of this paper is on the human induced
forces. Almost all existing force models for this type of load (defined
either in the time or frequency domain) are developed from the
assumption of perfect periodicity of the force and are based on force
measurements conducted on rigid (i.e. high frequency) surfaces. To
verify the different authors conclusions the vertical pressure
measurements invoked during the walking was performed, using
pressure gauges in various configurations. The obtained forces are
analyzed using Fourier transformation. This load is often decisive in
the design of footbridges. Design criteria and load models proposed
by widely used standards and other researchers were introduced and a
comparison was made.
Abstract: Corrugated wire mesh laminates (CWML) are a class
of engineered open cell structures that have potential for applications
in many areas including aerospace and biomedical engineering. Two
different methods of fabricating corrugated wire mesh laminates from
stainless steel, one using a high temperature Lithobraze alloy and the
other using a low temperature Eutectic solder for joining the
corrugated wire meshes are described herein. Their implementation is
demonstrated by manufacturing CWML samples of 304 and 316
stainless steel (SST). It is seen that due to the facility of employing
wire meshes of different densities and wire diameters, it is possible to
create CWML laminates with a wide range of effective densities. The
fabricated laminates are tested under uniaxial compression. The
variation of the compressive yield strength with relative density of the
CWML is compared to the theory developed by Gibson and Ashby for
open cell structures [22]. It is shown that the compressive strength of
the corrugated wire mesh laminates can be described using the same
equations by using an appropriate value for the linear coefficient in the
Gibson-Ashby model.
Abstract: Nylon 6-clay hybrid/neat nylon 6, sheath/core
bicomponent nanocomposite fibers containing 4 wt% of clay in
sheath section were melt spun at different take-up speeds. Their
orientation and crystalline structure were compared to those of neat
nylon 6 fibers. Birefringence measurements showed that the
orientation development in sheath and core parts of bicomponent
fibers was different. Crystallinity results showed that clay did not act
as a nucleating agent for bicomponent fibers. The neat nylon 6 fiber
had a smooth surface while striped pattern was appeared on the
surface of bicomponent fiber containing clay due to thermal
shrinkage of the core part.
Abstract: Compost manufacturing plants are one of units where
wastewater is produced in significantly large amounts. Wastewater
produced in these plants contains high amounts of substrate (organic
loads) and is classified as stringent waste which creates significant
pollution when discharged into the environment without treatment. A
compost production plant in the one of the Iran-s province treating
200 tons/day of waste is one of the most important environmental
pollutant operations in this zone. The main objectives of this paper
are to investigate the compost wastewater treatability in hybrid
anaerobic reactors with an upflow-downflow arrangement, to
determine the kinetic constants, and eventually to obtain an
appropriate mathematical model. After starting the hybrid anaerobic
reactor of the compost production plant, the average COD removal
rate efficiency was 95%.
Abstract: Segmentation in ultrasound images is challenging due to the interference from speckle noise and fuzziness of boundaries. In this paper, a segmentation scheme using fuzzy c-means (FCM) clustering incorporating both intensity and texture information of images is proposed to extract breast lesions in ultrasound images. Firstly, the nonlinear structure tensor, which can facilitate to refine the edges detected by intensity, is used to extract speckle texture. And then, a spatial FCM clustering is applied on the image feature space for segmentation. In the experiments with simulated and clinical ultrasound images, the spatial FCM clustering with both intensity and texture information gets more accurate results than the conventional FCM or spatial FCM without texture information.
Abstract: SAD (Sum of Absolute Difference) algorithm is
heavily used in motion estimation which is computationally highly
demanding process in motion picture encoding. To enhance the
performance of motion picture encoding on a VLIW processor, an
efficient implementation of SAD algorithm on the VLIW processor is
essential. SAD algorithm is programmed as a nested loop with a
conditional branch. In VLIW processors, loop is usually optimized by
software pipelining, but researches on optimal scheduling of software
pipelining for nested loops, especially nested loops with conditional
branches are rare. In this paper, we propose an optimal scheduling and
implementation of SAD algorithm with conditional branch on a VLIW
DSP processor. The proposed optimal scheduling first transforms the
nested loop with conditional branch into a single loop with conditional
branch with consideration of full utilization of ILP capability of the
VLIW processor and realization of earlier escape from the loop. Next,
the proposed optimal scheduling applies a modulo scheduling
technique developed for single loop. Based on this optimal scheduling
strategy, optimal implementation of SAD algorithm on TMS320C67x,
a VLIW DSP is presented. Through experiments on TMS320C6713
DSK, it is shown that H.263 encoder with the proposed SAD
implementation performs better than other H.263 encoder with other
SAD implementations, and that the code size of the optimal SAD
implementation is small enough to be appropriate for embedded
environments.
Abstract: A clustering is process to identify a homogeneous
groups of object called as cluster. Clustering is one interesting topic
on data mining. A group or class behaves similarly characteristics.
This paper discusses a robust clustering process for data images with
two reduction dimension approaches; i.e. the two dimensional
principal component analysis (2DPCA) and principal component
analysis (PCA). A standard approach to overcome this problem is
dimension reduction, which transforms a high-dimensional data into
a lower-dimensional space with limited loss of information. One of
the most common forms of dimensionality reduction is the principal
components analysis (PCA). The 2DPCA is often called a variant of
principal component (PCA), the image matrices were directly treated
as 2D matrices; they do not need to be transformed into a vector so
that the covariance matrix of image can be constructed directly using
the original image matrices. The decomposed classical covariance
matrix is very sensitive to outlying observations. The objective of
paper is to compare the performance of robust minimizing vector
variance (MVV) in the two dimensional projection PCA (2DPCA)
and the PCA for clustering on an arbitrary data image when outliers
are hiden in the data set. The simulation aspects of robustness and
the illustration of clustering images are discussed in the end of
paper
Abstract: Camera calibration plays an important role in the domain of the analysis of sports video. Considering soccer video, in most cases, the cross-points can be used for calibration at the center of the soccer field are not sufficient, so this paper introduces a new automatic camera calibration algorithm focus on solving this problem by using the properties of images of the center circle, halfway line and a touch line. After the theoretical analysis, a practicable automatic algorithm is proposed. Very little information used though, results of experiments with both synthetic data and real data show that the algorithm is applicable.
Abstract: Brain Computer Interface (BCI) has been recently
increased in research. Functional Near Infrared Spectroscope (fNIRs)
is one the latest technologies which utilize light in the near-infrared
range to determine brain activities. Because near infrared technology
allows design of safe, portable, wearable, non-invasive and wireless
qualities monitoring systems, fNIRs monitoring of brain
hemodynamics can be value in helping to understand brain tasks. In
this paper, we present results of fNIRs signal analysis indicating that
there exist distinct patterns of hemodynamic responses which
recognize brain tasks toward developing a BCI. We applied two
different mathematics tools separately, Wavelets analysis for
preprocessing as signal filters and feature extractions and Neural
networks for cognition brain tasks as a classification module. We
also discuss and compare with other methods while our proposals
perform better with an average accuracy of 99.9% for classification.
Abstract: This paper examines the use of mechanical aerator for
oxidation-ditch process. The rotor, which controls the aeration, is the
main component of the aeration process. Therefore, the objective of
this study is to find out the variations in overall oxygen transfer
coefficient (KLa) and aeration efficiency (AE) for different
configurations of aerator by varying the parameters viz. speed of
aerator, depth of immersion, blade tip angles so as to yield higher
values of KLa and AE. Six different configurations of aerator were
developed and fabricated in the laboratory and were tested for abovementioned
parameters. The curved blade rotor (CBR) emerged as a
potential aerator with blade tip angle of 47°.
The mathematical models are developed for predicting the
behaviour of CBR w.r.t kLa and power. In laboratory studies, the
optimum value of KLa and AE were observed to be 10.33 h-1 and
2.269 kg O2/ kWh.
Abstract: Building maintenance plays an important role among other activities in building operation. Building defect and damages are part of the building maintenance 'bread and butter' as their input indicated in the building inspection is very much justified, particularly as to determine the building performance. There will be no escape route or short cut from building maintenance work. This study attempts to identify a competitive performance that translates the Critical Success Factor achievements and satisfactorily meet the university-s expectation. The quality and efficiency of maintenance management operation of building depends, to some extent, on the building condition information, the expectation from the university sector and the works carried out for each maintenance activity. This paper reviews the critical success factor in building maintenance management practice for university sectors from four (4) perspectives which include (1) customer (2) internal processes (3) financial and (4) learning and growth perspective. The enhancement of these perspectives is capable to reach the maintenance management goal for a better living environment in university campus.
Abstract: Traditional wind tunnel models are meticulously machined from metal in a process that can take several months. While very precise, the manufacturing process is too slow to assess a new design's feasibility quickly. Rapid prototyping technology makes this concurrent study of air vehicle concepts via computer simulation and in the wind tunnel possible. This paper described the Affects layer thickness models product with rapid prototyping on Aerodynamic Coefficients for Constructed wind tunnel testing models. Three models were evaluated. The first model was a 0.05mm layer thickness and Horizontal plane 0.1μm (Ra) second model was a 0.125mm layer thickness and Horizontal plane 0.22μm (Ra) third model was a 0.15mm layer thickness and Horizontal plane 4.6μm (Ra). These models were fabricated from somos 18420 by a stereolithography (SLA). A wing-body-tail configuration was chosen for the actual study. Testing covered the Mach range of Mach 0.3 to Mach 0.9 at an angle-of-attack range of -2° to +12° at zero sideslip. Coefficients of normal force, axial force, pitching moment, and lift over drag are shown at each of these Mach numbers. Results from this study show that layer thickness does have an effect on the aerodynamic characteristics in general; the data differ between the three models by fewer than 5%. The layer thickness does have more effect on the aerodynamic characteristics when Mach number is decreased and had most effect on the aerodynamic characteristics of axial force and its derivative coefficients.
Abstract: The results from experimental research of deformation
by upsetting and die forging of lead specimens wit controlled impact
are presented. Laboratory setup for conducting the investigations,
which uses cold rocket engine operated with compressed air, is
described. The results show that when using controlled impact is
achieving greater plastic deformation and consumes less impact
energy than at ordinary impact deformation process.
Abstract: The simulation of extrusion process is studied widely
in order to both increase products and improve quality, with broad
application in wire coating. The annular tube-tooling extrusion was
set up by a model that is termed as Navier-Stokes equation in
addition to a rheological model of differential form based on singlemode
exponential Phan-Thien/Tanner constitutive equation in a twodimensional
cylindrical coordinate system for predicting the
contraction point of the polymer melt beyond the die. Numerical
solutions are sought through semi-implicit Taylor-Galerkin pressurecorrection
finite element scheme. The investigation was focused on
incompressible creeping flow with long relaxation time in terms of
Weissenberg numbers up to 200. The isothermal case was considered
with surface tension effect on free surface in extrudate flow and no
slip at die wall. The Stream Line Upwind Petrov-Galerkin has been
proposed to stabilize solution. The structure of mesh after die exit
was adjusted following prediction of both top and bottom free
surfaces so as to keep the location of contraction point around one
unit length which is close to experimental results. The simulation of
extrusion process is studied widely in order to both increase products
and improve quality, with broad application in wire coating. The
annular tube-tooling extrusion was set up by a model that is termed
as Navier-Stokes equation in addition to a rheological model of
differential form based on single-mode exponential Phan-
Thien/Tanner constitutive equation in a two-dimensional cylindrical
coordinate system for predicting the contraction point of the polymer
melt beyond the die. Numerical solutions are sought through semiimplicit
Taylor-Galerkin pressure-correction finite element scheme.
The investigation was focused on incompressible creeping flow with
long relaxation time in terms of Weissenberg numbers up to 200. The
isothermal case was considered with surface tension effect on free
surface in extrudate flow and no slip at die wall. The Stream Line
Upwind Petrov-Galerkin has been proposed to stabilize solution. The
structure of mesh after die exit was adjusted following prediction of
both top and bottom free surfaces so as to keep the location of
contraction point around one unit length which is close to
experimental results.
Abstract: The seemingly ambiguous title of this paper – use of the terms maturity and innovation in concord – signifies the imperative of every organisation within the competitive domain. Where organisational maturity and innovativeness were traditionally considered antonymous, the assimilation of these two seemingly contradictory notions is fundamental to the assurance of long-term organisational prosperity. Organisations are required, now more than ever, to grow and mature their innovation capability – rending consistent innovative outputs. This paper describes research conducted to consolidate the principles of innovation and identify the fundamental components that constitute organisational innovation capability. The process of developing an Innovation Capability Maturity Model is presented. A brief description is provided of the basic components of the model, followed by a description of the case studies that were conducted to evaluate the model. The paper concludes with a summary of the findings and potential future research.
Abstract: In the present work, study of the vibration of thin cylindrical shells made of a functionally gradient material (FGM) composed of stainless steel and nickel is presented. Material properties are graded in the thickness direction of the shell according to volume fraction power law distribution. The objective is to study the natural frequencies, the influence of constituent volume fractions and the effects of boundary conditions on the natural frequencies of the FG cylindrical shell. The study is carried out using third order shear deformation shell theory. The analysis is carried out using Hamilton's principle. The governing equations of motion of FG cylindrical shells are derived based on shear deformation theory. Results are presented on the frequency characteristics, influence of constituent volume fractions and the effects of free-free and clamped-clamped boundary conditions.
Abstract: This research contribution propels the idea of collaborating environment for the execution of student satellite projects in the backdrop of project management principles. The recent past has witnessed a technological shift in the aerospace industry from the big satellite projects to the small spacecrafts especially for the earth observation and communication purposes. This vibrant shift has vitalized the academia and industry to share their resources and to create a win-win paradigm of mutual success and technological development along with the human resource development in the field of aerospace. Small student satellites are the latest jargon of academia and more than 100 CUBESAT projects have been executed successfully all over the globe and many new student satellite projects are in the development phase. The small satellite project management requires the application of specific knowledge, skills, tools and techniques to achieve the defined mission requirements. The Authors have presented the detailed outline for the project management of student satellites and presented the role of industry to collaborate with the academia to get the optimized results in academic environment.
Abstract: A new fast correlation algorithm for calibrating the
wavelength of Optical Spectrum Analyzers (OSAs) was introduced
in [1]. The minima of acetylene gas spectra were measured and
correlated with saved theoretical data [2]. So it is possible to find the
correct wavelength calibration data using a noisy reference spectrum.
First tests showed good algorithmic performance for gas line spectra
with high noise. In this article extensive performance tests were made
to validate the noise resistance of this algorithm. The filter and
correlation parameters of the algorithm were optimized for improved
noise performance. With these parameters the performance of this
wavelength calibration was simulated to predict the resulting
wavelength error in real OSA systems. Long term simulations were
made to evaluate the performance of the algorithm over the lifetime
of a real OSA.