Abstract: Distributed wireless sensor network consist on several
scattered nodes in a knowledge area. Those sensors have as its only
power supplies a pair of batteries that must let them live up to five
years without substitution. That-s why it is necessary to develop
some power aware algorithms that could save battery lifetime as
much as possible. In this is document, a review of power aware
design for sensor nodes is presented. As example of implementations,
some resources and task management, communication, topology
control and routing protocols are named.
Abstract: The research study evaluated the performance of
irrigation system by using special scientific tools like Remote
Sensing and GIS technology, so that proper measurements could be
taken for the sustainable agriculture and water management.
Different performance evaluation parameters had been calculated for
the purposed data was gathered from field investigation and different
government and private organizations. According to the calculations,
organic matter ranges from 0.19% (low value) to 0.76% (high value).
In flat irrigation system for wheat yield ranges from 3347.16 to
5260.39 kg/ha, while the total water applied to wheat crop ranges
from 252.94 to 279.19 mm and WUE ranges from 13.07 to 18.37
kg/ha/mm. For rice yield ranges from 3347.47 to 5433.07 kg/ha with
total water supplied to rice crop ranges from 764.71 to 978.15 mm
and WUE ranges from 3.49 to 5.71 kg/ha/mm. Similarly, in raised
bed system wheat yield ranges from 4569.13 to 6008.60 kg/ha, total
water supplied ranges from 158.87 to 185.09 mm and WUE ranges
from 27.20 to 33.54 kg/ha/mm while in rice crop, yield ranges from
5285.04 to 6716.69 kg/ha, total water supplied ranges from 600.72 to
755.06 mm and WUE ranges from 6.41 to 10.05 kg/ha/mm. Almost
51.3% water saving is observed in bed irrigation system as compared
to flat system. Less water supplied to beds is more affective as its
WUE value is higher than flat system where more water is supplied
in both the seasons. Similarly, RWS values show that maximum
water deficit while minimum area is getting adequate water supply.
Greater yield is recorded in bed system as plant per square meter is
more in bed system in comparison of flat system Thus, the integration
of GIS tools to regularly compute performance indices could provide
irrigation managers with the means for managing efficiently the
irrigation system.
Abstract: This paper presents a complete procedure for tool path
planning and blade machining in 5-axis manufacturing. The actual
cutting contact and cutter locations can be determined by lead and tilt
angles. The tool path generation is implemented by piecewise curved
approximation and chordal deviation detection. An application about
drive surface method promotes flexibility of tool control and stability
of machine motion. A real manufacturing process is proposed to
separate the operation into three regions with five stages and to modify
the local tool orientation with an interactive algorithm.
Abstract: To improve HSE standards, oil and gas industries are
interested in using remotely controlled and autonomous robots instead
of human workers on offshore platforms. In addition to earlier reason
this strategy would increase potential revenue, efficient usage of
work experts and even would allow operations in more remote areas.
This article is the presentation of a custom climbing robot, called
Walloid, designed for offshore platform topside automation. This 4
arms climbing robot with grippers is an ongoing project at University
of Oslo.
Abstract: In ubiqutious healthcare environment, user's health data are transfered to the remote healthcare server by the user's wearable system or mobile phone. These collected user's health data should be managed and analyzed in the healthcare server, so that care giver or user can monitor user's physiological state. In this paper, we designed and developed the intelligent Healthcare Server to manage the user's health data using CDSS and ontology. Our system can analyze user's health data semantically using CDSS and ontology, and report the result of user's physiological raw data to the user and care giver.
Abstract: With the rapid expansion of city scale and the
excessive concentration of population, achieving relative equality of
extracurricular education resources and improving spatial service
performance of relevant facilities become necessary arduous tasks. In
urban space, extracurricular education facilities should offer better
service to its targeted area and promote the equality and efficiency of
education, which is accomplished by the allocation of facilities. Based
on questionnaire and survey for local students in Hangzhou City in
2009, this study classifies extracurricular education facilities in
meg-city and defines the equalization of these facilities. Then it is
suggested to establish extracurricular education facilities system
according to the development level of city and demands of local
students, and to introduce a spatial analysis method into urban
planning through the aspects of spatial distribution, travel cost and
spatial service scope. Finally, the practice of nine sub-districts of
Hangzhou is studied.
Abstract: Efficient utilization of existing water is a pressing
need for Pakistan. Due to rising population, reduction in present
storage capacity and poor delivery efficiency of 30 to 40% from
canal. A study to evaluate an irrigation system in the cotton-wheat
zone of Pakistan, after the watercourse lining was conducted. The
study is made on the basis of cropping pattern and salinity to evaluate
the system. This study employed an index-based approach of using
Geographic information system with field data. The satellite images
of different years were use to examine the effective area. Several
combinations of the ratio of signals received in different spectral
bands were used for development of this index. Near Infrared and
Thermal IR spectral bands proved to be most effective as this
combination helped easy detection of salt affected area and cropping
pattern of the study area. Result showed that 9.97% area under
salinity in 1992, 9.17% in 2000 and it left 2.29% in year 2005.
Similarly in 1992, 45% area is under vegetation it improves to 56%
and 65% in 2000 and 2005 respectively. On the basis of these results
evaluation is done 30% performance is increase after the watercourse
improvement.
Abstract: A. niger XP isolated from Vietnam produces very low amount of acidic phytase with optimal pH at 2.5 and 5.5. The phytase production of this strain was successfully improved through gene cloning and expression. A 1.4 - kb DNA fragment containing the coding region of the phyA gene was amplified by PCR and inserted into the expression vector pPICZαA with a signal peptide α- factor, under the control of AOX1 promoter. The recombined plasmid was transformed into the host strain P. pastoris KM71H and X33 by electroporation. Both host strains could efficiently express and secret phytase. The multicopy strains were screened for over expression of phytase. All the selected multicopy strains of P. pastoris X33 were examined for phytase activity, the maximum phytase yield of 1329 IU/ml was obtained after 4 days of incubation in medium BMM. The recombinant protein with MW of 97.4 KW showed to be the only one protein secreted in the culture broth. Multicopy transformant P. pastoris X33 supposed to be potential candidate for producing the commercial preparation of phytase.
Abstract: The scientific achievements coming from molecular
biology depend greatly on the capability of computational
applications to analyze the laboratorial results. A comprehensive
analysis of an experiment requires typically the simultaneous study
of the obtained dataset with data that is available in several distinct
public databases. Nevertheless, developing a centralized access to
these distributed databases rises up a set of challenges such as: what
is the best integration strategy, how to solve nomenclature clashes,
how to solve database overlapping data and how to deal with huge
datasets. In this paper we present GeNS, a system that uses a simple and yet innovative approach to address several biological data integration issues. Compared with existing systems, the main
advantages of GeNS are related to its maintenance simplicity and to its coverage and scalability, in terms of number of supported
databases and data types. To support our claims we present the current use of GeNS in two concrete applications. GeNS currently contains more than 140 million of biological relations and it can be
publicly downloaded or remotely access through SOAP web services.
Abstract: The forest fires in Thailand are annual occurrence which is the cause of air pollutions. This study intended to estimate the emission from forest fire during 2005-2009 using MODerateresolution Imaging Spectro-radiometer (MODIS) sensor aboard the Terra and Aqua satellites, experimental data, and statistical data. The forest fire emission is estimated using equation established by Seiler and Crutzen in 1982. The spatial and temporal variation of forest fire emission is analyzed and displayed in the form of grid density map. From the satellite data analysis suggested between 2005 and 2009, the number of fire hotspots occurred 86,877 fire hotspots with a significant highest (more than 80% of fire hotspots) in the deciduous forest. The peak period of the forest fire is in January to May. The estimation on the emissions from forest fires during 2005 to 2009 indicated that the amount of CO, CO2, CH4, and N2O was about 3,133,845 tons, 47,610.337 tons, 204,905 tons, and 6,027 tons, respectively, or about 6,171,264 tons of CO2eq. They also emitted 256,132 tons of PM10. The year 2007 was found to be the year when the emissions were the largest. Annually, March is the period that has the maximum amount of forest fire emissions. The areas with high density of forest fire emission were the forests situated in the northern, the western, and the upper northeastern parts of the country.
Abstract: The project describes the modeling of various
architectures mechatronics specifically morphologies of robots in an educational environment. Each structure developed by students of
pre-school, primary and secondary was created using the concept of
reverse engineering in a constructivist environment, to later be integrated in educational software that promotes the teaching of
educational Robotics in a virtual and economic environment.
Abstract: The elimination of ranitidine (a pharmaceutical
compound) has been carried out in the presence of UV-C radiation.
After some preliminary experiments, it has been experienced the no
influence of the gas nature (air or oxygen) bubbled in photolytic
experiments. From simple photolysis experiments the quantum yield
of this compound has been determined. Two photolytic
approximation has been used, the linear source emission in parallel
planes and the point source emission in spherical planes. The
quantum yield obtained was in the proximity of 0.05 mol Einstein-1
regardless of the method used. Addition of free radical promoters
(hydrogen peroxide) increases the ranitidine removal rate while the
use of photocatalysts (TiO2) negatively affects the process.
Abstract: The purpose of this paper is to shed light on the
controversial subject of tax incentives to promote regional
development. Although extensive research has been conducted, a
review of the literature gives an inconclusive answer to whether
economic incentives are effective. One reason is the fact that for
some researchers “effective" means the significant location of new
firms in targeted areas, while for others the creation of jobs
regardless if new firms are arriving in a significant fashion. We
present this dichotomy by analyzing a tax incentive program via both
alternatives: location and job creation. The contribution of the paper
is to inform policymakers about the potential opportunities and
pitfalls when designing incentive strategies. This is particularly
relevant, given that both the US and Europe have been promoting
incentives as a tool for regional economic development.
Abstract: Aiming at the problems existing in low-carbon technology of Chinese manufacturing industries, such as irrational energy structure, lack of technological innovation, financial constraints, this paper puts forward the suggestion that the leading role of the government is combined with the roles of enterprises and market. That is, through increasing the governmental funding the adjustment of the industrial structures and enhancement of the legal supervision are supported. Technological innovation is accelerated by the enterprises, and the carbon trading will be promoted so as to trigger the low-carbon revolution in Chinese manufacturing field.
Abstract: Magnesium alloys have gained increased attention in recent years in automotive, electronics, and medical industry. This because of magnesium alloys have better properties than aluminum alloys and steels in respects of their low density and high strength to weight ratio. However, the main problems of magnesium alloy welding are the crack formation and the appearance of porosity during the solidification. This paper proposes a unique technique to weld two thin sheets of AZ31B magnesium alloy using a paste containing Ag nanoparticles. The paste containing Ag nanoparticles of 5 nm in average diameter and an organic solvent was used to coat the surface of AZ31B thin sheet. The coated sheet was heated at 100 °C for 60 s to evaporate the solvent. The dried sheet was set as a lower AZ31B sheet on the jig, and then lap fillet welding was carried out by using a pulsed Nd:YAG laser in a closed box filled with argon gas. The characteristics of the microstructure and the corrosion behavior of the joints were analyzed by opticalmicroscopy (OM), energy dispersive spectrometry (EDS), electron probe micro-analyzer (EPMA), scanning electron microscopy (SEM), and immersion corrosion test. The experimental results show that the wrought AZ31B magnesium alloy can be joined successfully using Ag nanoparticles. Ag nanoparticles insert promote grain refinement, narrower the HAZ width and wider bond width compared to weld without and insert. Corrosion rate of welded AZ31B with Ag nanoparticles reduced up to 44 % compared to base metal. The improvement of corrosion resistance of welded AZ31B with Ag nanoparticles due to finer grains and large grain boundaries area which consist of high Al content. β-phase Mg17Al12 could serve as effective barrier and suppressed further propagation of corrosion. Furthermore, Ag distribution in fusion zone provide much more finer grains and may stabilize the magnesium solid solution making it less soluble or less anodic in aqueous
Abstract: Many people regard food events as part of gastronomic tourism and important in enhancing visitors’ experiences. Realizing the importance and contribution of food events to a country’s economy, the Malaysia government is undertaking greater efforts to promote such tourism activities to international tourists. Among other food events, the Ramadan bazaar is a unique food culture event, which receives significant attention from the Malaysia Ministry of Tourism. This study reports the empirical investigation into the international tourists’ perceptions, attraction towards the Ramadan bazaar and willingness in disseminating the information. Using the Ramadan bazaar at Kampung Baru, Kuala Lumpur as the data collection setting, results revealed that the Ramadan bazaar attributes (food and beverages, events and culture) significantly influenced the international tourist attraction to such a bazaar. Their high level of experience and satisfaction positively influenced their willingness to disseminate information. The positive response among the international tourists indicates that the Ramadan bazaar as gastronomic tourism can be used in addition to other tourism products as a catalyst to generate and boost the local economy. The related authorities that are closely associated with the tourism industry therefore should not ignore this indicator but continue to take proactive action in promoting the gastronomic event as one of the major tourist attractions.
Abstract: Since the 1940s, many promising telepresence
research results have been obtained. However, telepresence
technology still has not reached industrial usage. As human
intelligence is necessary for successful execution of most manual
assembly tasks, the ability of the human is hindered in some cases,
such as the assembly of heavy parts of small/medium lots or
prototypes. In such a case of manual assembly, the help of industrial
robots is mandatory. The telepresence technology can be considered
as a solution for performing assembly tasks, where the human
intelligence and haptic sense are needed to identify and minimize the
errors during an assembly process and a robot is needed to carry
heavy parts. In this paper, preliminary steps to integrate the
telepresence technology into industrial robot systems are introduced.
The system described here combines both, the human haptic sense
and the industrial robot capability to perform a manual assembly task
remotely using a force feedback joystick. Mapping between the
joystick-s Degrees of Freedom (DOF) and the robot-s ones are
introduced. Simulation and experimental results are shown and future
work is discussed.
Abstract: Tacit knowledge has been one of the most discussed
and contradictory concepts in the field of knowledge management
since the mid 1990s. The concept is used relatively vaguely to refer
to any type of information that is difficult to articulate, which has led
to discussions about the original meaning of the concept (adopted
from Polanyi-s philosophy) and the nature of tacit knowing. It is
proposed that the subject should be approached from the perspective
of cognitive science in order to connect tacit knowledge to
empirically studied cognitive phenomena. Some of the most
important examples of tacit knowing presented by Polanyi are
analyzed in order to trace the cognitive mechanisms of tacit knowing
and to promote better understanding of the nature of tacit knowledge.
The cognitive approach to Polanyi-s theory reveals that the
tacit/explicit typology of knowledge often presented in the
knowledge management literature is not only artificial but totally
opposite approach compared to Polanyi-s thinking.
Abstract: With the development of Internet and databases application techniques, the demand that lots of databases in the Internet are permitted to remote query and access for authorized users becomes common, and the problem that how to protect the copyright of relational databases arises. This paper simply introduces the knowledge of cloud model firstly, includes cloud generators and similar cloud. And then combined with the property of the cloud, a method of protecting relational databases copyright with cloud watermark is proposed according to the idea of digital watermark and the property of relational databases. Meanwhile, the corresponding watermark algorithms such as cloud watermark embedding algorithm and detection algorithm are proposed. Then, some experiments are run and the results are analyzed to validate the correctness and feasibility of the watermark scheme. In the end, the foreground of watermarking relational database and its research direction are prospected.
Abstract: Wireless Sensor Networks (WSNs) are used to monitor/observe vast inaccessible regions through deployment of large number of sensor nodes in the sensing area. For majority of WSN applications, the collected data needs to be combined with geographic information of its origin to make it useful for the user; information received from remote Sensor Nodes (SNs) that are several hops away from base station/sink is meaningless without knowledge of its source. In addition to this, location information of SNs can also be used to propose/develop new network protocols for WSNs to improve their energy efficiency and lifetime. In this paper, range free localization protocols for WSNs have been proposed. The proposed protocols are based on weighted centroid localization technique, where the edge weights of SNs are decided by utilizing fuzzy logic inference for received signal strength and link quality between the nodes. The fuzzification is carried out using (i) Mamdani, (ii) Sugeno, and (iii) Combined Mamdani Sugeno fuzzy logic inference. Simulation results demonstrate that proposed protocols provide better accuracy in node localization compared to conventional centroid based localization protocols despite presence of unintentional radio frequency interference from radio frequency (RF) sources operating in same frequency band.