Abstract: Harmonic pollution and low power factor in power
systems caused by power converters have been of great concern. To
overcome these problems several converter topologies using
advanced semiconductor devices and control schemes have been
proposed. This investigation is to identify a low cost, small size,
efficient and reliable ac to dc converter to meet the input performance
index of UPS. The performance of single phase and three phase ac to
dc converter along with various control techniques are studied and
compared. The half bridge converter topology with linear current
control is identified as most suitable. It is simple, energy efficient
because of single switch power loss and transformer-less operation of
UPS. The results are validated practically using a prototype built
using IGBT and analog controller. The performance for both single
and three-phase system is verified. Digital implementation of closed
loop control achieves higher reliability. Its cost largely depends on
chosen bit precision. The minimal bit precision for optimum
converter performance is identified as 16-bit with fixed-point
operation. From the investigation and practical implementation it is
concluded that half bridge ac – dc converter along with digital linear
controller meets the performance index of UPS for single and three
phase systems.
Abstract: Pre-germinated parboiled brown rice or Khao hang (in Thai) is paddy which undergoing the processes of soaking, steaming, drying and dehusking to obtain the edible form for consumption. The objectives of this research were to study the kinetic of pre-germinated parboiled brown rice drying using fluidization technique and to study the properties of pre-germinated parboiled brown rice after drying. The dryings were performed at the different temperatures of 110, 120 and 130 oC at the bed depth of 2 cm with the air velocity of 1.98 m/s. The results found that the higher drying temperature led to the faster moisture reduction. After drying until the moisture content of pre-germinated parboiled brown rice was lower than 14%wet basis, samples were taken to determine various qualities such as percentage of head rice and L* a* b* color values. The shade drying was used as a control. The results found that the higher drying temperature resulted in the decrease of head rice percentage. For the color assessment, the trend of L* and a* values was increased with the drying temperature, while the b* value was not significantly difference (p › 0.05) by drying temperatures. However, the b value of drying by fluidized bed dryer was higher than the control.
Abstract: In Geographic Information System, one of the sources
of obtaining needed geographic data is digitizing analog maps and
evaluation of aerial and satellite photos. In this study, a method will
be discussed which can be used to extract vectorial features and
creating vectorized drawing files for aerial photos. At the same time
a software developed for these purpose. Converting from raster to
vector is also known as vectorization and it is the most important step
when creating vectorized drawing files. In the developed algorithm,
first of all preprocessing on the aerial photo is done. These are;
converting to grayscale if necessary, reducing noise, applying some
filters and determining the edge of the objects etc. After these steps,
every pixel which constitutes the photo are followed from upper left
to right bottom by examining its neighborhood relationship and one
pixel wide lines or polylines obtained. The obtained lines have to be
erased for preventing confusion while continuing vectorization
because if not erased they can be perceived as new line, but if erased
it can cause discontinuity in vector drawing so the image converted
from 2 bit to 8 bit and the detected pixels are expressed as a different
bit. In conclusion, the aerial photo can be converted to vector form
which includes lines and polylines and can be opened in any CAD
application.
Abstract: Fault-proneness of a software module is the
probability that the module contains faults. A correlation exists
between the fault-proneness of the software and the measurable
attributes of the code (i.e. the static metrics) and of the testing (i.e.
the dynamic metrics). Early detection of fault-prone software
components enables verification experts to concentrate their time and
resources on the problem areas of the software system under
development. This paper introduces Genetic Algorithm based
software fault prediction models with Object-Oriented metrics. The
contribution of this paper is that it has used Metric values of JEdit
open source software for generation of the rules for the classification
of software modules in the categories of Faulty and non faulty
modules and thereafter empirically validation is performed. The
results shows that Genetic algorithm approach can be used for
finding the fault proneness in object oriented software components.
Abstract: In this paper, we demonstrate the adaptive
least-mean-square (LMS) filter modeling using SystemC. SystemC is
a modeling language that allows designer to model both hardware and
software component and makes it possible to design from high level
system of abstraction to low level system of abstraction. We produced
five adaptive least-mean-square filter models that are classed as five
abstraction levels using SystemC proceeding from the abstract model
to the more concrete model.
Abstract: A better understanding of cloud forest characteristic in a tropical montane cloud forest at Khao Nan, Nakhon Si Thammarat on climatic, vegetation, soil and hydrology were studied during 18-21 April 2007. The results showed that as air temperature at Sanyen cloud forest increased, the percent relative humidity decreased. The amount of solar radiation at Sanyen cloud forest had a positive association with the amount of solar radiation at Parah forest. The amount of solar radiation at Sanyen cloud forest was very low with a range of 0-19 W/m2. On the other hand, the amount of solar radiation at Parah forest was high with a range of 0-1000 W/m2. There was no difference between leaf width, leaf length, leaf thickness and leaf area with increasing in elevations. As the elevations increased, bush height and tree height decreased. There was no association between bush width and bush ratio with elevation. As the elevations increased, the percent epiphyte cover and the percent soil moisture increased but water temperature, conductivity, and dissolved oxygen decreased. The percent soil moistures and organic contents were higher at elevations above 900 m than elevations below.
Abstract: With the advance of multimedia and diagnostic
images technologies, the number of radiographic images is increasing
constantly. The medical field demands sophisticated systems for
search and retrieval of the produced multimedia document. This
paper presents an ongoing research that focuses on the semantic
content of radiographic image documents to facilitate semantic-based
radiographic image indexing and a retrieval system. The proposed
model would divide a radiographic image document, based on its
semantic content, and would be converted into a logical structure or
a semantic structure. The logical structure represents the overall
organization of information. The semantic structure, which is bound
to logical structure, is composed of semantic objects with
interrelationships in the various spaces in the radiographic image.
Abstract: An effort has been taken to simulate the combustion
and performance characteristics of biodiesel fuel in direct injection
(D.I) low heat rejection (LHR) diesel engine. Comprehensive
analyses on combustion characteristics such as cylinder pressure,
peak cylinder pressure, heat release and performance characteristics
such as specific fuel consumption and brake thermal efficiency are
carried out. Compression ignition (C.I) engine cycle simulation was
developed and modified in to LHR engine for both diesel and
biodiesel fuel. On the basis of first law of thermodynamics the
properties at each degree crank angle was calculated. Preparation and
reaction rate model was used to calculate the instantaneous heat
release rate. A gas-wall heat transfer calculations are based on the
ANNAND-s combined heat transfer model with instantaneous wall
temperature to analyze the effect of coating on heat transfer. The
simulated results are validated by conducting the experiments on the
test engine under identical operating condition on a turbocharged D.I
diesel engine. In this analysis 20% of biodiesel (derived from
Jatropha oil) blended with diesel and used in both conventional and
LHR engine. The simulated combustion and performance
characteristics results are found satisfactory with the experimental
value.
Abstract: One of the most important parameters to develop and
manage urban areas is appropriate selection of land surface to
develop green spaces in these areas. In this study, in order to identify
the most appropriate sites and areas cultivated for ornamental species
in Jiroft, Landsat Enhanced Thematic Mapper Plus (ETM+) images
due to extract the most important effective climatic and adaphic
parameters for growth ornamental species were used. After geometric
and atmospheric corrections applied, to enhance accuracy of multi
spectral (XS) bands, the fusion of Landsat XS bands by IRS-1D
panchromatic band (PAN) was performed. After field sampling to
evaluate the correlation between different factors in surface soil
sampling location and different bands digital number (DN) of ETM+
sensor on the same points, correlation tables formed using the best
computational model and the map of physical and chemical
parameters of soil was produced. Then the accuracy of them was
investigated by using kappa coefficient. Finally, according to
produced maps, the best areas for cultivation of recommended
species were introduced.
Abstract: This study investigated morphology of the Spanner Barb (Puntius lateristriga Valenciennes, 1842) and water quality at Thepchana waterfall. This study was conducted at Thepchana Waterfall, Khao Nan National Park from March to May 2007. There were 40 Spanner Barb collected with 20 males and 20 females. Males had an average of 5.57 cm in standard length, 6.62 cm in total length and 5.18 g in total body weight. Females had an average of 7.25 cm in standard length, 8.24 cm in total length and 10.96 g in total body weight. The length (L) – weight (W) relationships for combining sexes, males and females were LogW = -2.137 + 3.355logL, log W = -0.068 + 3.297logL, and log W = -2.068 + 3.297logL, respectively. The Spanner Barb were smaller size fish with a compressed form; terminal mouth; villiform teeth; ctenoid scale; concave tail; general body color yellowish olive, with slight reddish tint to fins; vertical band beginning below dorsal and horizontal stripe from base of tail almost to vertical band. They also had a vertical band midway between the eye and first vertical band. There was a black spot above anal fin. The bladder looked like J-shape. Inside of the bladder was found small insects and insect lava. The body length and the bowels length was 1:1 ratio. The water temperature ranged from 25.00 – 27.00 °C which was appropriate for their habitat characteristics. Acid - alkalinity ranged from 6.65 – 6.90 mg/l. Dissolved oxygen ranged from 4.55 – 4.70 mg/l. Water hardness ranged from 31.00 – 48.00 mg/l. The amount of ammonia was about 0.25 mg/l.
Abstract: This paper To get the angle value with a MEMS rate
gyroscope in some specific field, the usual method is to make an
integral operation to the rate output, which will lead the error
cumulating effect. So the rate gyro is not suitable. MEMS rate
integrating gyroscope (MRIG) will solve this problem. A DSP system
has been developed to implement the control arithmetic. The system
can measure the angle of rotation directly by the control loops that
make the sensor work in whole-angle mode. Modeling the system with
MATLAB, desirable results of angle outputs are got, which prove the
feasibility of the control arithmetic.
Abstract: This paper investigates the problem of tracking spa¬tiotemporal changes of a satellite image through the use of Knowledge Discovery in Database (KDD). The purpose of this study is to help a given user effectively discover interesting knowledge and then build prediction and decision models. Unfortunately, the KDD process for spatiotemporal data is always marked by several types of imperfections. In our paper, we take these imperfections into consideration in order to provide more accurate decisions. To achieve this objective, different KDD methods are used to discover knowledge in satellite image databases. Each method presents a different point of view of spatiotemporal evolution of a query model (which represents an extracted object from a satellite image). In order to combine these methods, we use the evidence fusion theory which considerably improves the spatiotemporal knowledge discovery process and increases our belief in the spatiotemporal model change. Experimental results of satellite images representing the region of Auckland in New Zealand depict the improvement in the overall change detection as compared to using classical methods.
Abstract: Electro-hydraulic power steering (EHPS) system for
the fuel rate reduction and steering feel improvement is comprised of
ECU including the logic which controls the steering system and BL
DC motor and produces the best suited cornering force, BLDC motor,
high pressure pump integrated module and basic oil-hydraulic circuit
of the commercial HPS system.
Electro-hydraulic system can be studied in two ways such as
experimental and computer simulation. To get accurate results in
experimental study of EHPS system, the real boundary management is
necessary which is difficult task. And the accuracy of the experimental
results depends on the preparation of the experimental setup and
accuracy of the data collection. The computer simulation gives
accurate and reliable results if the simulation is carried out considering
proper boundary conditions. So, in this paper, each component of
EHPS was modeled, and the model-based analysis and control logic
was designed by using AMESim
Abstract: In this study, ZnO nano rods and ZnO ultrafine particles were synthesized by Gel-casting method. The synthesized ZnO powder has a hexagonal zincite structure. The ZnO aggregates with rod-like morphology are typically 1.4 μm in length and 120 nm in diameter, which consist of many small nanocrystals with diameters of 10 nm. Longer wires connected by many hexahedral ZnO nanocrystals were obtained after calcinations at the temperature over 600° C.The crystalline structures and morphologies of the powder have been characterized by X-ray diffraction(XRD) and Scaning electron microscopy (SEM).The result shows that the different preparation conditions such as concentration H2O, calcinations time and calcinations temperature have a lot of influences upon the properties of nano ZnO powders, an increase in the temperature of the calcinations results in an increase of the grain size and also the increase of the calcinations time in high temperature makes the size of the grains bigger. The existences of extra watter prevent nano grains from improving like rod morphology. We have obtained the smallest grain size of ZnO powder by controlling the process conditions. Finally In a suitable condition, a novel nanostructure, namely bi-rod-like ZnO nano rods was found which is different from known ZnO nanostructures.
Abstract: We study the semiconvergence of Gauss-Seidel iterative
methods for the least squares solution of minimal norm of rank
deficient linear systems of equations. Necessary and sufficient conditions
for the semiconvergence of the Gauss-Seidel iterative method
are given. We also show that if the linear system of equations is
consistent, then the proposed methods with a zero vector as an initial
guess converge in one iteration. Some numerical results are given to
illustrate the theoretical results.
Abstract: Green Roofs offers numerous advantages, including lowering ambient temperature, which is of increasing interest due to global warming concerns. However, there are technical problems pertaining to waterproofing to be resolved. Currently, the only recognized green roof waterproofing test is the German standard FLL. This paper examines the potential of replicating the test in tropical climate and reducing the test duration by using pre-grown plants. A three year old sample and a new setup were used for this experimental study. The new setup was prepared with close reference to the FLL standards and was compared against the three year old sample. Results showed that the waterproofing membrane was damaged by plant roots in both setups. Joints integrity was also challenged.
Abstract: Optimum communication and performance in
Wireless Sensor Networks, constitute multi-facet challenges due to
the specific networking characteristics as well as the scarce resource
availability. Furthermore, it is becoming increasingly apparent that
isolated layer based approaches often do not meet the demands posed
by WSNs applications due to omission of critical inter-layer
interactions and dependencies. As a counterpart, cross-layer is
receiving high interest aiming to exploit these interactions and
increase network performance. However, in order to clearly identify
existing dependencies, comprehensive performance studies are
required evaluating the effect of different critical network parameters
on system level performance and behavior.This paper-s main
objective is to address the need for multi-parametric performance
evaluations considering critical network parameters using a well
known network simulator, offering useful and practical conclusions
and guidelines. The results reveal strong dependencies among
considered parameters which can be utilized by and drive future
research efforts, towards designing and implementing highly efficient
protocols and architectures.
Abstract: This paper presents an interactive modeling system of
polyhedra using the isomorphic graphs. Especially, Conway
polyhedron notation is implemented. The notation can be observed as
interactive animation.
Abstract: For decades, the defense business has been plagued by
not having a reliable, deterministic method to know when the Kalman
filter solution for passive ranging application is reliable for use by the
fighter pilot. This has made it hard to accurately assess when the
ranging solution can be used for situation awareness and weapons
use. To date, we have used ad hoc rules-of-thumb to assess when we
think the estimate of the Kalman filter standard deviation on range is
reliable. A reliable algorithm has been developed at BAE Systems
Electronics & Integrated Solutions that monitors the Kalman gain
matrix elements – and a patent is pending. The “settling" of the gain
matrix elements relates directly to when we can assess the time when
the passive ranging solution is within the 10 percent-of-truth value.
The focus of the paper is on surface-based passive ranging – but the
method is applicable to airborne targets as well.
Abstract: Artificial Immune System (AIS) is relatively naive paradigm for intelligent computations. The inspiration for AIS is derived from natural Immune System (IS). Classically it is believed that IS strives to discriminate between self and non-self. Most of the existing AIS research is based on this approach. Danger Theory (DT) argues this approach and proposes that IS fights against danger producing elements and tolerates others. We, the computational researchers, are not concerned with the arguments among immunologists but try to extract from it novel abstractions for intelligent computation. This paper aims to follow DT inspiration for intelligent data processing. The approach may introduce new avenue in intelligent processing. The data used is system calls data that is potentially significant in intrusion detection applications.