Abstract: In this contribution, a way to enhance the performance of the classic Genetic Algorithm is proposed. The idea of restarting a Genetic Algorithm is applied in order to obtain better knowledge of the solution space of the problem. A new operator of 'insertion' is introduced so as to exploit (utilize) the information that has already been collected before the restarting procedure. Finally, numerical experiments comparing the performance of the classic Genetic Algorithm and the Genetic Algorithm with restartings, for some well known test functions, are given.
Abstract: The experimental thermal performance of two heat
exchangers in closed-wet cooling tower (CWCT) was investigated in
this study. The test sections are heat exchangers which have multi path
that is used as the entrance of cooling water and are consisting of
bare-type copper tubes between 15.88mm and 19.05mm. The process
fluids are the cooling water that flows from top part of heat exchanger
to bottom side in the inner side of tube, and spray water that flows
gravitational direction in the outer side of it. Air contacts its outer side
of that as it counterflows. Heat and mass transfer coefficients and
cooling capacity were calculated with variations of process fluids,
multi path and different diameter tubes to figure out the performance
of characteristics of CWCT.
The main results were summarized as follows: The results show this
experiment is reliable with values of heat and mass transfer
coefficients comparing to values of correlations. Heat and mass
transfer coefficients and cooling capacity of two paths are higher than
these with one path using 15.88 and 19.05mm tubes. Cooling capacity
per unit volume with 15.88mm tube using one and two paths are
higher than 19.05mm tube due to increase of surface area per unit
volume.
Abstract: The purposes of this research were to study the citizen
participation in preventing illegal drugs in one of a poor and small
community of Bangkok, Thailand and to compare the level of
participation and concern of illegal drugs problem by using
demographic variables. This paper drew upon data collected from a
local citizens survey conducted in Bangkok, Thailand during summer
of 2012. A total of 200 respondents were elicited as data input for,
and one way ANOVA test. The findings revealed that the overall
citizen participation was in the level of medium. The mean score
showed that benefit from the program was ranked as the highest and
the decision to participate was ranked as second while the follow-up
of the program was ranked as the lowest.
In terms of the difference in demographic such as gender, age,
level of education, income, and year of residency, the hypothesis
testing’s result disclosed that there were no difference in their level
of participation. However, difference in occupation showed a
difference in their level of participation and concern which was
significant at the 0.05 confidence level.
Abstract: Permeability reduction induced by asphaltene
precipitation during gas injection is one of the serious problems in
the oil industry. This problem can lead to formation damage and
decrease the oil production rate. In this work, Malaysian light oil
sample has been used to investigate the effect CO2 injection and
Water Alternating Gas (WAG) injection on permeability reduction.
In this work, dynamic core flooding experiments were conducted to
study the effect of CO2 and WAG injection on the amount of
asphaltene precipitated. Core properties after displacement were
inspected for any permeability reduction to study the effect of
asphaltene precipitation on rock properties.
The results showed that WAG injection gave less asphaltene
precipitation and formation damage compared to CO2 injection. The
study suggested that WAG injection can be one of the important
factors of managing asphaltene precipitation.
Abstract: Cosmic showers, from their places of origin in space,
after entering earth generate secondary particles called Extensive Air
Shower (EAS). Detection and analysis of EAS and similar High
Energy Particle Showers involve a plethora of experimental setups
with certain constraints for which soft-computational tools like
Artificial Neural Network (ANN)s can be adopted. The optimality
of ANN classifiers can be enhanced further by the use of Multiple
Classifier System (MCS) and certain data - dimension reduction
techniques. This work describes the performance of certain data
dimension reduction techniques like Principal Component Analysis
(PCA), Independent Component Analysis (ICA) and Self Organizing
Map (SOM) approximators for application with an MCS formed
using Multi Layer Perceptron (MLP), Recurrent Neural Network
(RNN) and Probabilistic Neural Network (PNN). The data inputs are
obtained from an array of detectors placed in a circular arrangement
resembling a practical detector grid which have a higher dimension
and greater correlation among themselves. The PCA, ICA and SOM
blocks reduce the correlation and generate a form suitable for real
time practical applications for prediction of primary energy and
location of EAS from density values captured using detectors in a
circular grid.
Abstract: Nowadays, ontologies are the only widely accepted paradigm for the management of sharable and reusable knowledge in a way that allows its automatic interpretation. They are collaboratively created across the Web and used to index, search and annotate documents. The vast majority of the ontology based approaches, however, focus on indexing texts at document level. Recently, with the advances in ontological engineering, it became clear that information indexing can largely benefit from the use of general purpose ontologies which aid the indexing of documents at word level. This paper presents a concept indexing algorithm, which adds ontology information to words and phrases and allows full text to be searched, browsed and analyzed at different levels of abstraction. This algorithm uses a general purpose ontology, OntoRo, and an ontologically tagged corpus, OntoCorp, both developed for the purpose of this research. OntoRo and OntoCorp are used in a two-stage supervised machine learning process aimed at generating ontology tagging rules. The first experimental tests show a tagging accuracy of 78.91% which is encouraging in terms of the further improvement of the algorithm.
Abstract: This paper reports on the enhanced photoluminescence
(PL) of nanocomposites through the layered structuring of phosphor
and quantum dot (QD). Green phosphor of Sr2SiO4:Eu, red QDs of
CdSe/CdS/CdZnS/ZnS core-multishell, and thermo-curable resin
were used for this study. Two kinds of composite (layered and mixed)
were prepared, and the schemes for optical energy transfer between
QD and phosphor were suggested and investigated based on PL decay
characteristics. It was found that the layered structure is more effective
than the mixed one in the respects of PL intensity, PL decay and
thermal loss. When this layered nanocomposite (QDs on phosphor) is
used to make white light emitting diode (LED), the brightness is
increased by 37 %, and the color rendering index (CRI) value is raised
to 88.4 compared to the mixed case of 80.4.
Abstract: Railway Stations are prone to emergency due to
various reasons and proper monitor of railway stations are of
immense importance from various angles. A Petri-net representation
of a web-service-based Emergency management system has been
proposed in this paper which will help in monitoring situation of
train, track, signal etc. and in case of any emergency, necessary
resources can be dispatched.
Abstract: Previous studies on political budget cycles (PBCs)
implicitly assume the executive has full discretion power over fiscal
policy, neglecting the role of checks and balances of the legislature.
This paper goes beyond traditional PBCs models and sheds light on
the case study of Japan, South Korea, and Taiwan over the 1988-2007
periods. Based on the results, we find no evidence of electoral impacts
on the public expenditures in South Korean and Taiwan's
congressional elections. We also noted that PBCs are found on
Taiwan-s government expenditures during our sample periods.
Furthermore, the results also show that Japan-s legislature has a
significant checks and balances on government-s expenditures.
However, empirical results show that the legislature veto player in
Taiwan neither has effect on the reduction of public expenditures, nor
has the moderating effect over Taiwan-s political budget cycles, albeit
that they are statistically insignificant.We suggest that the existence of
PBCs in Taiwan is due to a weaker systemof checks and balances. Our
conjecture is that Taiwan either has no legislative veto player or has
observed low compliance to the law during the time period examined
in our study.
Abstract: Both the minimum energy consumption and
smoothness, which is quantified as a function of jerk, are generally
needed in many dynamic systems such as the automobile and the
pick-and-place robot manipulator that handles fragile equipments.
Nevertheless, many researchers come up with either solely
concerning on the minimum energy consumption or minimum jerk
trajectory. This research paper proposes a simple yet very interesting
relationship between the minimum direct and indirect jerks
approaches in designing the time-dependent system yielding an
alternative optimal solution. Extremal solutions for the cost functions
of direct and indirect jerks are found using the dynamic optimization
methods together with the numerical approximation. This is to allow
us to simulate and compare visually and statistically the time history
of control inputs employed by minimum direct and indirect jerk
designs. By considering minimum indirect jerk problem, the
numerical solution becomes much easier and yields to the similar
results as minimum direct jerk problem.
Abstract: One of the robust fault detection filter (RFDF)
designing method is based on sliding-mode theory. The main purpose
of our study is to introduce an innovative simplified reference
residual model generator to formulate the RFDF as a sliding-mode
observer without any manipulation package or transformation matrix,
through which the generated residual signals can be evaluated. So the
proposed design is more explicit and requires less design parameters
in comparison with approaches requiring changing coordinates. To
the best author's knowledge, this is the first time that the sliding
mode technique is applied to detect actuator and sensor faults in a
real boiler. The designing procedure is proposed in a drum boiler in
Synvendska Kraft AB Plant in Malmo, Sweden as a multivariable
and strongly coupled system. It is demonstrated that both sensor and
actuator faults can robustly be detected. Also sensor faults can be
diagnosed and isolated through this method.
Abstract: In this paper, we present a maintenance model of a
two-unit series system with economic dependence. Unit#1 which is
considered to be more expensive and more important, is subject to
condition monitoring (CM) at equidistant, discrete time epochs and
unit#2, which is not subject to CM has a general lifetime distribution.
The multivariate observation vectors obtained through condition
monitoring carry partial information about the hidden state of unit#1,
which can be in a healthy or a warning state while operating. Only the
failure state is assumed to be observable for both units. The objective
is to find an optimal opportunistic maintenance policy minimizing
the long-run expected average cost per unit time. The problem
is formulated and solved in the partially observable semi-Markov
decision process framework. An effective computational algorithm
for finding the optimal policy and the minimum average cost is
developed, illustrated by a numerical example.
Abstract: Mobile ad-hoc networks (MANETs) are a form of
wireless networks which do not require a base station for providing
network connectivity. Mobile ad-hoc networks have many
characteristics which distinguish them from other wireless networks
which make routing in such networks a challenging task. Cluster
based routing is one of the routing schemes for MANETs in which
various clusters of mobile nodes are formed with each cluster having
its own clusterhead which is responsible for routing among clusters.
In this paper we have proposed and implemented a distributed
weighted clustering algorithm for MANETs. This approach is based
on combined weight metric that takes into account several system
parameters like the node degree, transmission range, energy and
mobility of the nodes. We have evaluated the performance of
proposed scheme through simulation in various network situations.
Simulation results show that proposed scheme outperforms the
original distributed weighted clustering algorithm (DWCA).
Abstract: Cry j 1 is a causative substance of Japanese cedar
pollinosis, and it may deteriorate by Cry j 1 invasion to a lower
respiratory tract. We observed airborne particles containing Cry j 1 by
an immunofluorescence technique using a fluorescence microscope,
and we clarified that Cry j 1 exist as aggregates of airborne fine
particles (< 1.1 μm) in the urban atmosphere. Airborne Cry j 1 may
react with air pollutants and be denature to a substance deteriorated
Japanese cedar pollinosis. Therefore, we applied a sodium dodecyl
sulfate-polyacrylamide gel electrophoresis (SDS-PAGE) to evaluate a
Cry j 1 reacted with various air pollutants by liquid phase reaction,
and calculated kinetics constants of Cry j 1 extracted from pollens
collected in various sites and airborne fine particles containing Cry j
1 by using a surface plasmon resonance (SPR) method. As a result, it
is suggested that Cry j 1 may be denatured by air pollutants during
the transportation to the urban atmosphere.
Abstract: Currently is characterized production engineering
together with the integration of industrial automation and robotics
such very quick view of to manufacture the products. The production
range is continuously changing, expanding and producers have to be
flexible in this regard. It means that need to offer production
possibilities, which can respond to the quick change. Engineering
product development is focused on supporting CAD software, such
systems are mainly used for product design. That manufacturers are
competitive, it should be kept procured machines made available
capable of responding to output flexibility. In response to that
problem is the development of flexible manufacturing systems,
consisting of various automated systems. The integration of flexible
manufacturing systems and subunits together with product design and
of engineering is a possible solution for this issue. Integration is
possible through the implementation of CIM systems. Such a solution
and finding a hyphen between CAD and procurement system ICIM
3000 from Festo Co. is engaged in the research project and this
contribution. This can be designed the products in CAD systems and
watch the manufacturing process from order to shipping by the
development of methods and processes of integration, This can be
modeled in CAD systems products and watch the manufacturing
process from order to shipping to develop methods and processes of
integration, which will improve support for product design
parameters by monitoring of the production process, by creating of
programs for production using the CAD and therefore accelerates the
a total of process from design to implementation.
Abstract: Today, money laundering (ML) poses a serious threat
not only to financial institutions but also to the nation. This criminal
activity is becoming more and more sophisticated and seems to have
moved from the cliché of drug trafficking to financing terrorism and
surely not forgetting personal gain. Most international financial
institutions have been implementing anti-money laundering solutions
(AML) to fight investment fraud. However, traditional investigative
techniques consume numerous man-hours. Recently, data mining
approaches have been developed and are considered as well-suited
techniques for detecting ML activities. Within the scope of a
collaboration project for the purpose of developing a new solution for
the AML Units in an international investment bank, we proposed a
data mining-based solution for AML. In this paper, we present a
heuristics approach to improve the performance for this solution. We
also show some preliminary results associated with this method on
analysing transaction datasets.
Abstract: This paper presents a new technique for detection of
human faces within color images. The approach relies on image
segmentation based on skin color, features extracted from the two-dimensional
discrete cosine transform (DCT), and self-organizing
maps (SOM). After candidate skin regions are extracted, feature
vectors are constructed using DCT coefficients computed from those
regions. A supervised SOM training session is used to cluster feature
vectors into groups, and to assign “face" or “non-face" labels to those
clusters. Evaluation was performed using a new image database of
286 images, containing 1027 faces. After training, our detection
technique achieved a detection rate of 77.94% during subsequent
tests, with a false positive rate of 5.14%. To our knowledge, the
proposed technique is the first to combine DCT-based feature
extraction with a SOM for detecting human faces within color
images. It is also one of a few attempts to combine a feature-invariant
approach, such as color-based skin segmentation, together with
appearance-based face detection. The main advantage of the new
technique is its low computational requirements, in terms of both
processing speed and memory utilization.
Abstract: We demonstrate the synthesis of intermediary views
within a sequence of color encoded, materials discriminating, X-ray
images that exhibit animated depth in a visual display. During the
image acquisition process, the requirement for a linear X-ray detector
array is replaced by synthetic image. Scale Invariant Feature
Transform, SIFT, in combination with material segmented morphing
is employed to produce synthetic imagery. A quantitative analysis of
the feature matching performance of the SIFT is presented along with
a comparative study of the synthetic imagery. We show that the total
number of matches produced by SIFT reduces as the angular
separation between the generating views increases. This effect is
accompanied by an increase in the total number of synthetic pixel
errors. The trends observed are obtained from 15 different luggage
items. This programme of research is in collaboration with the UK
Home Office and the US Dept. of Homeland Security.
Abstract: In the present study, the incorporation of graphene
into blends of acrylonitrile-butadiene-styrene terpolymer with
polypropylene (ABS/PP) was investigated focusing on the
improvement of their thermomechanical characteristics and the effect
on their rheological behavior. The blends were prepared by melt
mixing in a twin-screw extruder and were characterized by measuring
the MFI as well as by performing DSC, TGA and mechanical tests.
The addition of graphene to ABS/PP blends tends to increase their
melt viscosity, due to the confinement of polymer chains motion.
Also, graphene causes an increment of the crystallization temperature
(Tc), especially in blends with higher PP content, because of the
reduction of surface energy of PP nucleation, which is a consequence
of the attachment of PP chains to the surface of graphene through the
intermolecular CH-π interaction. Moreover, the above nanofiller
improves the thermal stability of PP and increases the residue of
thermal degradation at all the investigated compositions of blends,
due to the thermal isolation effect and the mass transport barrier
effect. Regarding the mechanical properties, the addition of graphene
improves the elastic modulus, because of its intrinsic mechanical
characteristics and its rigidity, and this effect is particularly strong in
the case of pure PP.
Abstract: This paper presents an integrated model that
automatically measures the change of rivers, damage area of bridge
surroundings, and change of vegetation. The proposed model is on the
basis of a neurofuzzy mechanism enhanced by SOM optimization
algorithm, and also includes three functions to deal with river imagery.
High resolution imagery from FORMOSAT-2 satellite taken before
and after the invasion period is adopted. By randomly selecting a
bridge out of 129 destroyed bridges, the recognition results show that
the average width has increased 66%. The ruined segment of the
bridge is located exactly at the most scour region. The vegetation
coverage has also reduced to nearly 90% of the original. The results
yielded from the proposed model demonstrate a pinpoint accuracy rate
at 99.94%. This study brings up a successful tool not only for
large-scale damage assessment but for precise measurement to
disasters.