Abstract: Flash memory has become an important storage device
in many embedded systems because of its high performance, low
power consumption and shock resistance. Multi-level cell (MLC) is
developed as an effective solution for reducing the cost and increasing
the storage density in recent years. However, most of flash file system
cannot handle the error correction sufficiently. To correct more errors
for MLC, we implement Reed-Solomon (RS) code to YAFFS, what is
widely used for flash-based file system. RS code has longer computing
time but the correcting ability is much higher than that of Hamming
code.
Abstract: This paper aims at numerically analysing the effect
of an active flow control (AFC) by a vortex generator jet (VGJ)
submerged in a boundary layer via Chimera Grids and Detached-
Eddy Simulation (DES). The performance of DES results are
judged against Reynolds-Averaged Navier-Stokes (RANS) and
compared with the experiments that showed an unsteady vortex
motion downstream of VGJ. Experimental results showed that
the mechanism of embedding logitudinal vortex structure in the
main stream flow is quite effective in increasing the near wall
momentum of separated aircraft wing. In order to simulate such
a flow configuration together with the VGJ, an efficient numerical
approach is required. This requirement is fulfilled by performing
the DES simulation over the flat plate using the DLR TAU Code.
The DES predictions identify the vortex region via smooth hybrid
length scale and predict the unsteady vortex motion observed in
the experiments. The DES results also showed that the sufficient
grid refinement in the vortex region resolves the turbulent scales
downstream of the VGJ, the spatial vortex core postion and nondimensional
momentum coefficient RVx .
Abstract: The aerodynamic stall control of a baseline 13-percent
thick NASA GA(W)-2 airfoil using a synthetic jet actuator (SJA) is
presented in this paper. Unsteady Reynolds-averaged Navier-Stokes
equations are solved on a hybrid grid using a commercial software to
simulate the effects of a synthetic jet actuator located at 13% of the
chord from the leading edge at a Reynolds number Re = 2.1x106 and
incidence angles from 16 to 22 degrees. The experimental data for the
pressure distribution at Re = 3x106 and aerodynamic coefficients at
Re = 2.1x106 (angle of attack varied from -16 to 22 degrees) without
SJA is compared with the computational fluid dynamic (CFD)
simulation as a baseline validation. A good agreement of the CFD
simulations is obtained for aerodynamic coefficients and pressure
distribution.
A working SJA has been integrated with the baseline airfoil and
initial focus is on the aerodynamic stall control at angles of attack
from 16 to 22 degrees. The results show a noticeable improvement in
the aerodynamic performance with increase in lift and decrease in
drag at these post stall regimes.
Abstract: The aim of this study was to test whether the Attention
Networks Test (ANT) showed temporal decrements in performance.
Vigilance tasks typically show such decrements, which may reflect
impairments in executive control resulting from cognitive fatigue.
The ANT assesses executive control, as well as alerting and
orienting. Thus, it was hypothesized that ANT executive control
would deteriorate over time. Manipulations including task condition
(trial composition) and masking were included in the experimental
design in an attempt to increase performance decrements. However,
results showed that there is no temporal decrement on the ANT. The
roles of task demands, cognitive fatigue and participant motivation in
producing this result are discussed. The ANT may not be an effective
tool for investigating temporal decrement in attention.
Abstract: Agropyron cristatum L. Gaertn. is a native grass of
semiarid region in Iran which is quit resistant to cool and drought
climate and withstand heavy grazing. This species has close
phylogenetic relationship with Triticum and Hordeum. In this
research, the effect of seven different concentrations of growth
regulator 2,4-D on callus production and somatic embryogenesis of
A. cristatum was investigated on Murashige and Skoog medium. The
results showed that the rate of callus, embryo and neomorph were
highest in 1 mg L-1 2,4-D. Callus production was increased in 1 mg
L-1 2,4-D but dramatically decreased at 5.5 and 9 mg L-1 2,4-D. The
somatic embryos were observed at 1 and 4 mg L-1 2,4-D but matured
embryos and plantlet were only occurred at 1 mg L-1 2,4-D. There
were significant differences between 1 mg L-1 2,4-D and other
treatments for producing globular and torpedo embryos, plantlet,
rooted callus and number of roots (p
Abstract: Today technological process makes possible surface
control of producing parts which is needful for product quality
guarantee. Geometrical structure of part surface includes form,
proportion, accuracy to shape, accuracy to size, alignment and
surface topography (roughness, waviness, etc.). All these parameters
are dependence at technology, production machine parameters,
material properties, but also at human, etc. Every parameters
approves at total part accuracy, it is means at accuracy to shape. One
of the most important accuracy to shape element is roundness. This
paper will be deals by comparison of roughness deviations at
coordination measuring machines and at special single purpose
machines. Will describing measuring by discreet method
(discontinuous) and scanning method (continuous) at coordination
measuring machines and confrontation with reference method using
at single purpose machines.
Abstract: Bay leaves have been shown to improve insulin
function in vitro but the effects on people have not been determined.
The objective of this study was to determine if bay leaves may be
important in the prevention and/or alleviation of type 1 diabetes.
Methods: Fifty five people with type 1 diabetes were divided into
two groups, 45 given capsules containing 3 g of bay leaves per day
for 30 days and 10 given a placebo capsules. Results All the patients
consumed bay leaves shows reduced serum glucose with significant
decreases 27% after 30 d. Total cholesterol decreased, 21 %, after 30
days with larger decreases in low density lipoprotein (LDL) 24%.
High density lipoprotein (HDL) increased 20% and Triglycerides
also decreased 26%. There were no significant changes in the
placebo group. Conclusion, this study demonstrates that consumption
of bay leaves, 3 g/d for 30 days, decreases risk factors for diabetes
and cardiovascular diseases and suggests that bay leaves may be
beneficial for people with type 1 diabetes.
Abstract: Phase error in communications systems degrades error
performance. In this paper, we present a simple approximation for the
average error probability of the binary phase shift keying (BPSK) in
the presence of phase error having a uniform distribution on arbitrary
intervals. For the simple approximation, we use symmetry and
periodicity of a sinusoidal function. Approximate result for the
average error probability is derived, and the performance is verified
through comparison with simulation result.
Abstract: The OTOP Entrepreneurship that used to create
substantial source of income for local Thai communities are now in a
stage of exigent matters that required assistances from public sectors
due to over Entrepreneurship of duplicative ideas, unable to adjust
costs and prices, lack of innovation, and inadequate of quality
control. Moreover, there is a repetitive problem of middlemen who
constantly corner the OTOP market. Local OTOP producers become
easy preys since they do not know how to add more values, how to
create and maintain their own brand name, and how to create proper
packaging and labeling. The suggested solutions to local OTOP
producers are to adopt modern management techniques, to find
knowhow to add more values to products and to unravel other
marketing problems. The objectives of this research are to study the
prevalent OTOP products management and to discover direction to
manage OTOP products to enhance the effectiveness of OTOP
Entrepreneurship in Nonthaburi Province, Thailand. There were 113
participants in this study. The research tools can be divided into two
parts: First part is done by questionnaire to find responses of the
prevalent OTOP Entrepreneurship management. Second part is the
use of focus group which is conducted to encapsulate ideas and local
wisdom. Data analysis is performed by using frequency, percentage,
mean, and standard deviation as well as the synthesis of several small
group discussions. The findings reveal that 1) Business Resources:
the quality of product is most important and the marketing of product
is least important. 2) Business Management: Leadership is most
important and raw material planning is least important. 3) Business
Readiness: Communication is most important and packaging is least
important. 4) Support from public sector: Certified from the
government is most important and source of raw material is the least
important.
Abstract: Cooling with sound is a physical phenomenon allowed by Thermo-Acoustics in which acoustic energy is transformed into a negative heat transfer, in other words: into cooling! Without needing any harmful gas, the transformation is environmentally friendly and can respond to many needs in terms of air conditioning, food refrigeration for domestic use, and cooling medical samples for example. To explore the possibilities of this cooling solution on a small scale, the TACS prototype has been designed, consisting of a low cost thermoacoustic refrigerant “pipe” able to lower the temperature by a few degrees. The obtained results are providing an interesting element for possible future of thermo-acoustic refrigeration.
Abstract: This paper presents an automated inspection algorithm
for a thick plate. Thick plates typically have various types of surface
defects, such as scabs, scratches, and roller marks. These defects have
individual characteristics including brightness and shape. Therefore, it
is not simple to detect all the defects. In order to solve these problems
and to detect defects more effectively, we propose a dual light
switching lighting method and a defect detection algorithm based on
Gabor filters.
Abstract: This paper is devoted to predict laminar and turbulent
heating rates around blunt re-entry spacecraft at hypersonic
conditions. Heating calculation of a hypersonic body is normally
performed during the critical part of its flight trajectory. The
procedure is of an inverse method, where a shock wave is assumed,
and the body shape that supports this shock, as well as the flowfield
between the shock and body, are calculated. For simplicity the
normal momentum equation is replaced with a second order pressure
relation; this simplification significantly reduces computation time.
The geometries specified in this research, are parabola and ellipsoids
which may have conical after bodies. An excellent agreement is
observed between the results obtained in this paper and those
calculated by others- research. Since this method is much faster than
Navier-Stokes solutions, it can be used in preliminary design,
parametric study of hypersonic vehicles.
Abstract: Development of a Robust Supply Chain for Dynamic
Operating Environment as we move further into the twenty first
century, organisations are under increasing pressure to deliver a high
product variation at a reasonable cost without compromise in quality.
In a number of cases this will take the form of a customised or high
variety low volume manufacturing system that requires prudent
management of resources, among a number of functions, to achieve
competitive advantage. Purchasing and Supply Chain management is
one of such function and due to the substantial interaction with
external elements needs to be strategically managed. This requires a
number of primary and supporting tools that will enable the
appropriate decisions to be made rapidly. This capability is
especially vital in a dynamic environment as it provides a pivotal role
in increasing the profit margin of the product. The management of
this function can be challenging by itself and even more for Small
and Medium Enterprises (SMEs) due to the limited resources and
expertise available at their disposal.
This paper discusses the development of tools and concepts
towards effectively managing the purchasing and supply chain
function. The developed tools and concepts will provide a cost
effective way of managing this function within SMEs. The paper
further shows the use of these tools within Contechs, a manufacturer
of luxury boat interiors, and the associated benefits achieved as a
result of this implementation. Finally a generic framework towards
use in such environments is presented.
Abstract: This paper proposes and implements an core transform architecture, which is one of the major processes in HEVC video compression standard. The proposed core transform architecture is implemented with only adders and shifters instead of area-consuming multipliers. Shifters in the proposed core transform architecture are implemented in wires and multiplexers, which significantly reduces chip area. Also, it can process from 4×4 to 16×16 blocks with common hardware by reusing processing elements. Designed core transform architecture in 0.13um technology can process a 16×16 block with 2-D transform in 130 cycles, and its gate count is 101,015 gates.
Abstract: This study develops a relation to explore the factors influencing management and technology capabilities in strategic alliances. Alliances between firms are recognizing increasingly popular as a vehicle to create and extract greater value from the market. Firm’s alliance can be described as the collaborative problem solving process to solve problems jointly. This study starts from research questions what factors of firm’s management and technology characteristics affect performance of firms which are formed alliances. In this study, we investigated the effect of strategic alliances on company performance. That is, we try to identify whether firms made an alliance with other organizations are differed by characteristics of management and technology. And we test that alliance type and alliance experiences moderate the relationship between firm’s capabilities and its performance. We employ problem-solving perspective and resource-based view perspective to shed light on this research questions. The empirical work is based on the Survey of Business Activities conducted from2006 to 2008 by Statistics Korea. We verify correlations between to point out that these results contribute new empirical evidence on the effect of strategic alliances on company performance.
Abstract: There are several ways of improving the performance of a vapor compression refrigeration cycle. Use of an ejector as expansion device is one of the alternative ways. The present paper aims at evaluate the performance improvement of a vapor compression refrigeration cycle under a wide range of operating conditions. A numerical model is developed and a parametric study of important parameters such as condensation (30-50°C) and evaporation temperatures (-20-5°C), nozzle and diffuser efficiencies (0.75-0.95), subcooling and superheating degrees (0-15K) are investigated. The model verification gives a good agreement with the literature data. The simulation results revealed that condensation temperature has the highest effect (129%) on the performance improvement ratio while superheating has the lowest one (6.2%). Among ejector efficiencies, the diffuser efficiency has a significant effect on the COP of ejector expansion refrigeration cycle. The COP improvement percentage decreases from 10.9% to 4.6% as subcooling degrees increases by 15K.
Abstract: In this paper, we study on finite projective Hjelmslev planes M(Zq) coordinatized by Hjelmslev ring Zq (where prime power q = pk). We obtain finite hyperbolic Klingenberg planes from these planes under certain conditions. Also, we give a combinatorical result on M(Zq), related by deleting a line from lines in same neighbour.
Abstract: Ant colony optimization is an ant algorithm framework that took inspiration from foraging behavior of ant colonies. Indeed, ACO algorithms use a chemical communication, represented by pheromone trails, to build good solutions. However, ants involve different communication channels to interact. Thus, this paper introduces the acoustic communication between ants while they are foraging. This process allows fine and local exploration of search space and permits optimal solution to be improved.
Abstract: The aim of the current work is to present a comparison among three popular optimization methods in the inverse elastostatics problem (IESP) of flaw detection within a solid. In more details, the performance of a simulated annealing, a Hooke & Jeeves and a sequential quadratic programming algorithm was studied in the test case of one circular flaw in a plate solved by both the boundary element (BEM) and the finite element method (FEM). The proposed optimization methods use a cost function that utilizes the displacements of the static response. The methods were ranked according to the required number of iterations to converge and to their ability to locate the global optimum. Hence, a clear impression regarding the performance of the aforementioned algorithms in flaw identification problems was obtained. Furthermore, the coupling of BEM or FEM with these optimization methods was investigated in order to track differences in their performance.
Abstract: In this paper we propose a novel Run Time Interface
(RTI) technique to provide an efficient environment for MPI jobs on
the heterogeneous architecture of PARAM Padma. It suggests an
innovative, unified framework for the job management interface
system in parallel and distributed computing. This approach employs
proxy scheme. The implementation shows that the proposed RTI is
highly scalable and stable. Moreover RTI provides the storage access
for the MPI jobs in various operating system platforms and improve
the data access performance through high performance C-DAC
Parallel File System (C-PFS). The performance of the RTI is
evaluated by using the standard HPC benchmark suites and the
simulation results show that the proposed RTI gives good
performance on large scale supercomputing system.