Abstract: This study was carried out to develop a flotation
procedure for an oxide copper ore from a Region in Central Africa
for producing an 18% copper concentrate for downstream processing
at maximum recovery from a 4% copper feed grade. The copper
recoveries achieved from the test work were less than 50% despite
changes in reagent conditions (multistage sulphidisation, use of RCA
emulsion and mixture, use of AM 2, etc). The poor recoveries were
attributed to the mineralogy of the ore from which copper silicates
accounted for approximately 70% (mass) of the copper minerals in
the ore. These can be complex and difficult to float using
conventional flotation methods. Best results were obtained using
basic sulphidisation procedures, a high flotation temperature and
extended flotation residence time.
Abstract: The main objective of this paper is to estimate the cost of road traffic accidents in Egypt. The Human Capital (HC) approach, specifically the Gross-Loss-of-Output methodology, is adopted for estimation. Moreover, cost values obtained by previous national literature are updated using the inflation rates. The results indicate an estimated cost of road traffic accidents in Egypt of approximately 10 billion Egyptian Pounds (about $US 1.8 billion) for the year 2008. In addition, it is expected that this cost will rise in 2009 to 11.8 billion Egyptian Pounds (about $US 2.1 billion).
Abstract: Ozone (O3) is considered as one of the most
phytotoxic pollutants with deleterious effects on living and non living
components of Ecosystems. It reduces growth and yield of many
crops as well as alters the physiology and crop quality. The present
study described series of experiments to investigate the effects of
ambient O3 at different locations with different ambient levels of O3
depending on proximity to pollutant source and ranged between 17
ppb/h in control experiment to 112 ppb/h in industrial area
respectively. The ambient levels in other three locations (King Saud
University botanical garden, King Fahd Rd, and Almanakh Garden)
were 61,61,77 ppb/h respectively. Tow legume crops species (vicia
vaba L ; and Pisum sativum) differ in their phenology and sensitivity
were used. The results showed a significant negative effect to ozone
on morphology, number of injured leaves, growth and productivity
with a difference in the degree of response depending on the plant
type. Visia Faba showed sensitivity to ozone to number and leaf area
and the degree of injury leaves 3, pisum sativum show higher
sensitivity for the gas for degree of injury 1,The relative growth rate
and seed weight, it turns out there is no significant difference
between the two plants in plant height and number of seeds.
Abstract: Various models have been derived by studying large number of completed software projects from various organizations and applications to explore how project sizes mapped into project effort. But, still there is a need to prediction accuracy of the models. As Neuro-fuzzy based system is able to approximate the non-linear function with more precision. So, Neuro-Fuzzy system is used as a soft computing approach to generate model by formulating the relationship based on its training. In this paper, Neuro-Fuzzy technique is used for software estimation modeling of on NASA software project data and performance of the developed models are compared with the Halstead, Walston-Felix, Bailey-Basili and Doty Models mentioned in the literature.
Abstract: The paper presents an analytical solution for dispersion
of a solute in the peristaltic motion of a couple stress fluid
through a porous medium with slip condition in the presence of both
homogeneous and heterogeneous chemical reactions. The average
effective dispersion coefficient has been found using Taylor-s limiting
condition and long wavelength approximation. The effects of various
relevant parameters on the average coefficient of dispersion have been
studied. The average effective dispersion coefficient tends to increase
with permeability parameter but tends to decrease with homogeneous
chemical reaction rate parameter, couple stress parameter, slip parameter
and heterogeneous reaction rate parameter.
Abstract: The mathematical framework for studying of a fuzzy approximate reasoning is presented in this paper. Two important defuzzification methods (Area defuzzification and Height defuzzification) besides the center of gravity method which is the best well known defuzzification method are described. The continuity of the defuzzification methods and its application to a fuzzy feedback control are discussed.
Abstract: Shear walls are used in most of the tall buildings for
carrying the lateral load. When openings for doors or windows are
necessary to be existed in the shear walls, a special type of the shear
walls is used called "coupled shear walls" which in some cases is
stiffened by specific beams and so, called "stiffened coupled shear
walls".
In this paper, a mathematical method for geometrically nonlinear
analysis of the stiffened coupled shear walls has been presented.
Then, a suitable formulation for determining the critical load of the
stiffened coupled shear walls under gravity force has been proposed.
The governing differential equations for equilibrium and deformation
of the stiffened coupled shear walls have been obtained by setting up
the equilibrium equations and the moment-curvature relationships for
each wall. Because of the complexity of the differential equation, the
energy method has been adopted for approximate solution of the
equations.
Abstract: This paper mainly investigates the environmental and
economic impacts of worldwide use of electric vehicles. It can be
concluded that governments have good reason to promote the use of
electric vehicles. First, the global vehicles population is evaluated with
the help of grey forecasting model and the amount of oil saving is
estimated through approximate calculation. After that, based on the
game theory, the amount and types of electricity generation needed by
electronic vehicles are established. Finally, some conclusions on the
government-s attitudes are drawn.
Abstract: This paper presents a Reliability-Based Topology
Optimization (RBTO) based on Evolutionary Structural Optimization
(ESO). An actual design involves uncertain conditions such as
material property, operational load and dimensional variation.
Deterministic Topology Optimization (DTO) is obtained without
considering of the uncertainties related to the uncertainty parameters.
However, RBTO involves evaluation of probabilistic constraints,
which can be done in two different ways, the reliability index
approach (RIA) and the performance measure approach (PMA). Limit
state function is approximated using Monte Carlo Simulation and
Central Composite Design for reliability analysis. ESO, one of the
topology optimization techniques, is adopted for topology
optimization. Numerical examples are presented to compare the DTO
with RBTO.
Abstract: In view of geological origin, formation of the shallow
gas reservoir of the Hangzhou Bay, northern Zhejiang Province,
eastern China, and original occurrence characteristics of the gassy
sand are analyzed. Generally, gassy sand in scale gas reservoirs is in
the state of residual moisture content and the approximate scope of
initial matric suction of sand ranges about from 0kPa to100kPa.
Results based on GDS triaxial tests show that the classical shear
strength formulas of unsaturated soil can not effectively describe basic
strength characteristics of gassy sand; the relationship between
apparent cohesion and matric suction of gassy sand agrees well with
the power function, which can reasonably be used to describe the
strength of gassy sand. In the stress path of gas release, shear strength
of gassy sand will increase and experimental results show the formula
proposed in this paper can effectively predict the strength increment.
When saturated strength indexes of the sand are used in engineering
design, moderate reduction should be considered.
Abstract: In this work, the condensation fraction and transition
temperature of neutral many bosonic system are studied within the
static fluctuation approximation (SFA). The effect of the potential
parameters such as the strength and range on the condensate fraction
was investigated. A model potential consisting of a repulsive step
potential and an attractive potential well was used. As the potential
strength or the core radius of the repulsive part increases, the
condensation fraction is found to be decreased at the same
temperature. Also, as the potential depth or the range of the attractive
part increases, the condensation fraction is found to be increased. The
transition temperature is decreased as the potential strength or the
core radius of the repulsive part increases, and it increases as the
potential depth or the range of the attractive part increases.
Abstract: This research aims to study the preferable tourism and
the elements of choosing tourist destination from domestic tourist in
Bangkok and the nearby areas in Thailand.The data were collected by
using 1249 set of questionnaires, in mid-August 2012. The result
illustrates that religious destinations are the most preferable places
for the tourist. The average expense per travel is approximately 47
USD a time. Travellers travel based on the advertisement in the
television and internet and their decisions is based on the reputation
of the destinations.
The result on a place dimension demonstrates the neatness and
well managed location play a crucial role on tourist destination.
Gender, age, marriage status and their origins are affecting their
spending and travelling behaviour. The researcher reckon that
providing the area of arcade, selling the souvenir and promoting
tourism among a young professional group would be an important
key follow the income distribution policy, including managing the
destination to welcome the family group, which the result is to
identified as the highest spending.
Abstract: The experimental and theoretical results of a ZVS
(Zero Voltage Switching) isolated flyback DC-DC converter using
multilayered coreless PCB step down 2:1 transformer are presented.
The performance characteristics of the transformer are shown which
are useful for the parameters extraction. The measured energy
efficiency of the transformer is found to be more than 94% with the
sinusoidal input voltage excitation. The designed flyback converter
has been tested successfully upto the output power level of 10W,
with a switching frequency in the range of 2.7MHz-4.3MHz. The
input voltage of the converter is varied from 25V-40V DC.
Frequency modulation technique is employed by maintaining
constant off time to regulate the output voltage of the converter. The
energy efficiency of the isolated flyback converter circuit under ZVS
condition in the MHz frequency region is found to be approximately
in the range of 72-84%. This paper gives the comparative results in
terms of the energy efficiency of the hard switched and soft switched
flyback converter in the MHz frequency region.
Abstract: In this paper a PID control strategy using neural
network adaptive RASP1 wavelet for WECS-s control is proposed.
It is based on single layer feedforward neural networks with hidden
nodes of adaptive RASP1 wavelet functions controller and an infinite
impulse response (IIR) recurrent structure. The IIR is combined by
cascading to the network to provide double local structure resulting
in improving speed of learning. This particular neuro PID controller
assumes a certain model structure to approximately identify the
system dynamics of the unknown plant (WECS-s) and generate the
control signal. The results are applied to a typical turbine/generator
pair, showing the feasibility of the proposed solution.
Abstract: In this study, a semi-cylinder obstacle placed in a
channel is handled to determine the effect of flow and heat transfer
around the obstacle. Both faces of the semi-cylinder are used in the
numerical analysis. First, the front face of the semi-cylinder is stated
perpendicular to flow, than the rear face is placed. The study is
carried out numerically, by using commercial software ANSYS 11.0.
The well-known κ-ε model is applied as the turbulence model.
Reynolds number is in the range of 104 to 105 and air is assumed as
the flowing fluid. The results showed that, heat transfer increased
approximately 15 % in the front faze case, while it enhanced up to 28
% in the rear face case.
Abstract: In this article the investigation about installation heat
recovery steam generation (HRSG) on the exhaust of turbo generators of phases 2&3 at South Pars Gas Complex is presented.
The temperature of exhaust gas is approximately 665 degree centigrade, Installation of heat recovery boiler was simulated in
ThermoFlow 17.0.2 software, based on test operation data and the
equipments site operation conditions in Pars exclusive economical energy area, the affect of installation HRSG package on the available
gas turbine and its operation parameters, ambient temperature, the
exhaust temperatures steam flow rate were investigated. Base on the results recommended HRSG package should have the capacity for 98
ton per hour high pressure steam generation this refinery, by use of
exhaust of three gas turbines for each package in operation condition of each refinery at 30 degree centigrade. Besides saving energy this
project will be an Environment-Friendly project. The Payback Period
is estimated approximately 1.8 year, with considering Clean Development Mechanism.
Abstract: The disaster from functional gastrointestinal disorders has detrimental impact on the quality of life of the effected population and imposes a tremendous social and economic burden. There are, however, rare diagnostic methods for the functional gastrointestinal disorders. Our research group identified recently that the gastrointestinal tract well in the patients with the functional gastrointestinal disorders becomes more rigid than healthy people when palpating the abdominal regions overlaying the gastrointestinal tract. Objective of current study is, therefore, identify feasibility of a diagnostic system for the functional gastrointestinal disorders based on ultrasound technique, which can quantify the characteristics above. Two-dimensional finite difference (FD) models (one normal and two rigid model) were developed to analyze the reflective characteristic (displacement) on each soft-tissue layer responded after application of ultrasound signals. The FD analysis was then based on elastic ultrasound theory. Validation of the model was performed via comparison of the characteristic of the ultrasonic responses predicted by FD analysis with that determined from the actual specimens for the normal and rigid conditions. Based on the results from FD analysis, ultrasound system for diagnosis of the functional gastrointestinal disorders was developed and clinically tested via application of it to 40 human subjects with/without functional gastrointestinal disorders who were assigned to Normal and Patient Groups. The FD models were favorably validated. The results from FD analysis showed that the maximum displacement amplitude in the rigid models (0.12 and 0.16) at the interface between the fat and muscle layers was explicitly less than that in the normal model (0.29). The results from actual specimens showed that the maximum amplitude of the ultrasonic reflective signal in the rigid models (0.2±0.1Vp-p) at the interface between the fat and muscle layers was explicitly higher than that in the normal model (0.1±0.2 Vp-p). Clinical tests using our customized ultrasound system showed that the maximum amplitudes of the ultrasonic reflective signals near to the gastrointestinal tract well for the patient group (2.6±0.3 Vp-p) were generally higher than those in normal group (0.1±0.2 Vp-p). Here, maximum reflective signals was appeared at 20mm depth approximately from abdominal skin for all human subjects, corresponding to the location of the boundary layer close to gastrointestinal tract well. These findings suggest that our customized ultrasound system using the ultrasonic reflective signal may be helpful to the diagnosis of the functional gastrointestinal disorders.
Abstract: This paper presents a novel approach to assessing textile porosity by the application of the image analysis techniques. The images of different types of sample fabrics, taken through a microscope when the fabric is placed over a constant light source,transfer the problem into the image analysis domain. Indeed, porosity can thus be expressed in terms of a brightness percentage index calculated on the digital microscope image. Furthermore, it is meaningful to compare the brightness percentage index with the air permeability and the tightness indices of each fabric type. We have experimentally shown that there exists an approximately linear relation between brightness percentage and air permeability indices.
Abstract: Both the minimum energy consumption and
smoothness, which is quantified as a function of jerk, are generally
needed in many dynamic systems such as the automobile and the
pick-and-place robot manipulator that handles fragile equipments.
Nevertheless, many researchers come up with either solely
concerning on the minimum energy consumption or minimum jerk
trajectory. This research paper considers the indirect minimum Jerk
method for higher order differential equation in dynamics
optimization proposes a simple yet very interesting indirect jerks
approaches in designing the time-dependent system yielding an
alternative optimal solution. Extremal solutions for the cost functions
of indirect jerks are found using the dynamic optimization methods
together with the numerical approximation. This case considers the
linear equation of a simple system, for instance, mass, spring and
damping. The simple system uses two mass connected together by
springs. The boundary initial is defined the fix end time and end
point. The higher differential order is solved by Galerkin-s methods
weight residual. As the result, the 6th higher differential order shows
the faster solving time.
Abstract: In this paper we present the deep study about the Bio-
Medical Images and tag it with some basic extracting features (e.g.
color, pixel value etc). The classification is done by using a nearest
neighbor classifier with various distance measures as well as the
automatic combination of classifier results. This process selects a
subset of relevant features from a group of features of the image. It
also helps to acquire better understanding about the image by
describing which the important features are. The accuracy can be
improved by increasing the number of features selected. Various
types of classifications were evolved for the medical images like
Support Vector Machine (SVM) which is used for classifying the
Bacterial types. Ant Colony Optimization method is used for optimal
results. It has high approximation capability and much faster
convergence, Texture feature extraction method based on Gabor
wavelets etc..