Abstract: Interaction between mixing and crystallization is often
ignored despite the fact that it affects almost every aspect of the
operation including nucleation, growth, and maintenance of the
crystal slurry. This is especially pronounced in multiple impeller
systems where flow complexity is increased. By choosing proper
mixing parameters, what closely depends on the knowledge of the
hydrodynamics in a mixing vessel, the process of batch cooling
crystallization may considerably be improved. The values that render
useful information when making this choice are mixing time and
power consumption. The predominant motivation for this work was
to investigate the extent to which radial dual impeller configuration
influences mixing time, power consumption and consequently the
values of metastable zone width and nucleation rate. In this research,
crystallization of borax was conducted in a 15 dm3 baffled batch
cooling crystallizer with an aspect ratio (H/T) of 1.3. Mixing was
performed using two straight blade turbines (4-SBT) mounted on the
same shaft that generated radial fluid flow. Experiments were
conducted at different values of N/NJS ratio (impeller speed/
minimum impeller speed for complete suspension), D/T ratio
(impeller diameter/crystallizer diameter), c/D ratio (lower impeller
off-bottom clearance/impeller diameter), and s/D ratio (spacing
between impellers/impeller diameter). Mother liquor was saturated at
30°C and was cooled at the rate of 6°C/h. Its concentration was
monitored in line by Na-ion selective electrode. From the values of
supersaturation that was monitored continuously over process time, it
was possible to determine the metastable zone width and
subsequently the nucleation rate using the Mersmann’s nucleation
criterion. For all applied dual impeller configurations, the mixing
time was determined by potentiometric method using a pulse
technique, while the power consumption was determined using a
torque meter produced by Himmelstein & Co. Results obtained in
this investigation show that dual impeller configuration significantly
influences the values of mixing time, power consumption as well as
the metastable zone width and nucleation rate. A special attention
should be addressed to the impeller spacing considering the flow
interaction that could be more or less pronounced depending on the
spacing value.
Abstract: Nowadays, food safety is a great public concern;
therefore, robust and effective techniques are required for detecting
the safety situation of goods. Hyperspectral Imaging (HSI) is an
attractive material for researchers to inspect food quality and safety
estimation such as meat quality assessment, automated poultry
carcass inspection, quality evaluation of fish, bruise detection of
apples, quality analysis and grading of citrus fruits, bruise detection
of strawberry, visualization of sugar distribution of melons,
measuring ripening of tomatoes, defect detection of pickling
cucumber, and classification of wheat kernels. HSI can be used to
concurrently collect large amounts of spatial and spectral data on the
objects being observed. This technique yields with exceptional
detection skills, which otherwise cannot be achieved with either
imaging or spectroscopy alone. This paper presents a nonlinear
technique based on kernel Fukunaga-Koontz transform (KFKT) for
detection of fat content in ground meat using HSI. The KFKT which
is the nonlinear version of FKT is one of the most effective
techniques for solving problems involving two-pattern nature. The
conventional FKT method has been improved with kernel machines
for increasing the nonlinear discrimination ability and capturing
higher order of statistics of data. The proposed approach in this paper
aims to segment the fat content of the ground meat by regarding the
fat as target class which is tried to be separated from the remaining
classes (as clutter). We have applied the KFKT on visible and nearinfrared
(VNIR) hyperspectral images of ground meat to determine
fat percentage. The experimental studies indicate that the proposed
technique produces high detection performance for fat ratio in ground
meat.
Abstract: Debts reconstruction under some of moratorium
projects is one of important method that highly benefits to both the
Banks and farmers. The method can reduce probabilities for nonprofits
loan. This paper discuss about debts reconstruction and career
development training for farmers in Thailand between 2011 and
2013. The research designed is mix-method between quantitative
survey and qualitative survey. Sample size for quantitative method is
1003 cases. Data gathering procedure is between October and
December 2013. Main results affirmed that debts reconstruction is
needed. And there are numerous benefits from farmers’ career
development training. Many of farmers who attend field school
activities able to bring knowledge learned to apply for the farms’
work. They can reduce production costs. Framers’ quality of life and
their household well-being also improve. This program should apply
in any countries where farmers have highly debts and highly risks for
not return the debts.
Abstract: Asphalt pavement itself is a mixture made up of mainly aggregates, binders, and fillers that acts as a composition used for pavement construction. An experimental program was setup to determine the fatigue performance test of Asphalt with three different grades of conventional binders. Asphalt specimen has achieved the maximum optimum bulk density and air voids with a consistent bulk density of 2.3 t/m3, with an air void of 5% ± 0.5, before loading into the Asphalt Mixture Performance Tested (AMPT) for fatigue test. The number of cycles is defined as the point where phase angle drops, which is caused by the formation of cracks due to the increasing micro cracks when asphalt is undergoing repeated cycles of loading. Thus, the data collected are analyzed using the drop of phase angle as failure criteria. Based in the data analyzed, it is evident that the fatigue life of asphalt lies on the grade of binder. The result obtained shows that all specimens do experience a drop in phase angle due to macro cracks in the asphalt specimen.
Abstract: High double excitation of two-electron atoms has been
investigated using hyperpherical coordinates within a modified
adiabatic expansion technique. This modification creates a novel
fictitious force leading to a spontaneous exchange symmetry breaking
at high double excitation. The Pauli principle must therefore be
regarded as approximation valid only at low excitation energy.
Threshold electron scattering from high Rydberg states shows an
unexpected time reversal symmetry breaking. At threshold for double
escape we discover a broad (few eV) Cooper pair.
Abstract: Ultrasonic metal welding has been the subject of ongoing research and development, most recently concentrating on metal joining in miniature devices, for example to allow solder-free wire bonding. As well as at the small scale, there are also opportunities to research the joining of thicker sheet metals and to widen the range of similar and dissimilar materials that can be successfully joined using this technology. This study presents the design, characterisation and test of a lateral-drive ultrasonic metal spot welding device. The ultrasonic metal spot welding horn is modelled using finite element analysis (FEA) and its vibration behaviour is characterised experimentally to ensure ultrasonic energy is delivered effectively to the weld coupon. The welding stack and fixtures are then designed and mounted on a test machine to allow a series of experiments to be conducted for various welding and ultrasonic parameters. Weld strength is subsequently analysed using tensile-shear tests. The results show how the weld strength is particularly sensitive to the combination of clamping force and ultrasonic vibration amplitude of the welding tip, but there are optimal combinations of these and also limits that must be clearly identified.
Abstract: This paper applies recursive cointegration analysis to
examine the dynamic changes in Feldstein-Horioka saving-investment
(S-I) coefficients across China and the ASEAN-5 countries over time.
To the extent that the S-I coefficients measure international capital
mobility, the main empirical results are as follows. The recursive trace
statistics show that the investment- savings nexus varies in these six
countries. There is no cointegration between investment and savings in
three countries (China, Malaysia, and Singapore), which means that
the mobility of the capital markets in the three is high and that
domestic investment in them will be financed by the global pool of
capital. As to the other three countries (Indonesia, Thailand, and
Philippines), there is cointegration between investment and savings for
part of the sample period in the three, including before 2002 for
Thailand, before 2001 for Indonesia, and before 2002 for Philippines.
This shows these three countries achieved highly mobile and open
capital markets later.
Abstract: Centrifugal-casting machine is used in manufacturing
special machine components like multi-layer journal bearing used in
all internal combustion engine, steam, gas turbine and air craft turboengine
where isotropic properties and high precisions are desired.
Moreover, this machine can be used in manufacturing thin wall hightech
machine components like cylinder liners and piston rings of IC
engine and other machine parts like sleeves, and bushes. Heavy-duty
machine component like railway wheel can also be prepared by
centrifugal casting. A lot of technological developments are required
in casting process for production of good casted machine body and
machine parts. Usually defects like blowholes, surface roughness,
chilled surface etc. are found in sand casted machine parts. But these
can be removed by centrifugal casting machine using rotating
metallic die. Moreover, die rotation, its temperature control, and good
pouring practice can contribute to the quality of casting because of
the fact that the soundness of a casting in large part depends upon
how the metal enters into the mold or dies and solidifies. Poor
pouring practice leads to variety of casting defects such as
temperature loss, low quality casting, excessive turbulence, over
pouring etc. Besides these, handling of molten metal is very
unsecured and dangerous for the workers. In order to get rid of all
these problems, the need of an automatic pouring device arises. In
this research work, a robot assisted pouring device and a centrifugal
casting machine are designed, developed constructed and tested
experimentally which are found to work satisfactorily. The robot
assisted pouring device is further modified and developed for using it
in actual metal casting process. Lot of settings and tests are required
to control the system and ultimately it can be used in automation of
centrifugal casting machine to produce high-tech machine parts with
desired precision.
Abstract: The objective of this research is to develop a general technique so that one may predict the dynamic behaviour of a three-dimensional scale crane model subjected to time-dependent moving point forces by means of conventional finite element computer packages. To this end, the whole scale crane model is divided into two parts: the stationary framework and the moving substructure. In such a case, the dynamic responses of a scale crane model can be predicted from the forced vibration responses of the stationary framework due to actions of the four time-dependent moving point forces induced by the moving substructure. Since the magnitudes and positions of the moving point forces are dependent on the relative positions between the trolley, moving substructure and the stationary framework, it can be found from the numerical results that the time histories for the moving speeds of the moving substructure and the trolley are the key factors affecting the dynamic responses of the scale crane model.
Abstract: The boundary layer separation and new active flow control of a NACA 0025 airfoil were studied experimentally. This new flow control is sometimes known as a co-flow jet (cfj) airfoil. This paper presents the fluctuating velocity in a wall jet over the co-flow jet airfoil subjected to an adverse pressure gradient and a curved surface. In these results, the fluctuating velocity at the inner part increasing by increased the angle of attack up to 12o and this has due to the jet energized, while the angle of attack 20o has different. The airfoil cord based Reynolds number has 105.
Abstract: A composite material with carbon fiber and polymer
matrix has been used as adherent for manufacturing adhesive joints.
In order to evaluate different fiber orientations on joint performance,
the adherents with the 0°, ±15°, ±30°, ±45° fiber orientations were
used in the single lap joint configuration. The joints with an overlap
length of 25 mm were prepared according to the ASTM 1002
specifications and subjected to tensile loadings. The structural
adhesive used was a two-part epoxy to be cured at 70°C for an hour.
First, mechanical behaviors of the adherents were measured using
three point bending test. In the test, considerations were given to
stress to failure and elastic modulus. The results were compared with
theoretical ones using rule of mixture. Then, the joints were
manufactured in a specially prepared jig, after a proper surface
preparation. Experimental results showed that the fiber orientations
of the adherents affected the joint performance considerably; the
joints with ±45° adherents experienced the worst shear strength, half
of those with 0° adherents, and in general, there was a great
relationship between the fiber orientations and failure mechanisms.
Delamination problems were observed for many joints, which were
thought to be due to peel effects at the ends of the overlap. It was
proved that the surface preparation applied to the adherent surface
was adequate. For further explanation of the results, a numerical
work should be carried out using a possible non-linear analysis.
Abstract: This paper investigates the application of metallic
coatings on high fiber volume fraction carbon/epoxy polymer matrix
composites. For the grip of the metallic layer, a method of modifying
the surface of the composite by introducing a mixture of copper and
steel powder (filler powders) which can reduce the impact of thermal
spray particles. The powder was introduced to the surface at the time
of the forming. Arc spray was used to project the zinc coating layer.
The substrate was grit blasted to avoid poor adherence. The porosity, microstructure, and morphology of layers are
characterized by optical microscopy, SEM and image analysis. The
samples were studied also in terms of hardness and erosion resistance.
This investigation did not reveal any visible evidence damage to the
substrates. The hardness of zinc layer was about 25.94 MPa and the
porosity was around (∼6.70%). The erosion test showed that the zinc
coating improves the resistance to erosion. Based on the results
obtained, we can conclude that thermal spraying allows the production
of protective coating on PMC. Zinc coating has been identified as a
compatible material with the substrate. The filler powders layer
protects the substrate from the impact of hot particles and allows
avoiding the rupture of brittle carbon fibers.
Abstract: The rising demand for format-flexible packaging
machines is caused by current market changes. Increasing the formatflexibility
is a new goal for the packaging machine manufacturers’
product development process. There are no methodical or designorientated
tools for a comprehensive consideration of this target. This
paper defines the term format-flexibility in the context of packaging
machines and shows the state-of-the-art for improving the
changeover of production machines. The requirements for a new
approach and the concept itself will be introduced, and the method
elements will be explained. Finally, the use of the concept and the
result of the development of a format-flexible packaging machine
will be shown.
Abstract: Smart metering and demand response are gaining
ground in industrial and residential applications. Smart Appliances
have been given concern towards achieving Smart home. The success
of Smart grid development relies on the successful implementation of
Information and Communication Technology (ICT) in power sector.
Smart Appliances have been the technology under development and
many new contributions to its realization have been reported in the
last few years. The role of ICT here is to capture data in real time,
thereby allowing bi-directional flow of information/data between
producing and utilization point; that lead a way for the attainment of
Smart appliances where home appliances can communicate between
themselves and provide a self-control (switch on and off) using the
signal (information) obtained from the grid. This paper depicts the
background on ICT for smart appliances paying a particular attention
to the current technology and identifying the future ICT trends for
load monitoring through which smart appliances can be achieved to
facilitate an efficient smart home system which promote demand
response program. This paper grouped and reviewed the recent
contributions, in order to establish the current state of the art and
trends of the technology, so that the reader can be provided with a
comprehensive and insightful review of where ICT for smart
appliances stands and is heading to. The paper also presents a brief
overview of communication types, and then narrowed the discussion
to the load monitoring (Non-intrusive Appliances Load Monitoring
‘NALM’). Finally, some future trends and challenges in the further
development of the ICT framework are discussed to motivate future
contributions that address open problems and explore new
possibilities.
Abstract: The very well-known stacked sets of numbers referred
to as Pascal’s triangle present the coefficients of the binomial
expansion of the form (x+y)n. This paper presents an approach (the
Staircase Horizontal Vertical, SHV-method) to the generalization of
planar Pascal’s triangle for polynomial expansion of the form
(x+y+z+w+r+⋯)n. The presented generalization of Pascal’s triangle
is different from other generalizations of Pascal’s triangles given in
the literature. The coefficients of the generalized Pascal’s triangles,
presented in this work, are generated by inspection, using embedded
Pascal’s triangles. The coefficients of I-variables expansion are
generated by horizontally laying out the Pascal’s elements of (I-1)
variables expansion, in a staircase manner, and multiplying them with
the relevant columns of vertically laid out classical Pascal’s elements,
hence avoiding factorial calculations for generating the coefficients
of the polynomial expansion. Furthermore, the classical Pascal’s
triangle has some pattern built into it regarding its odd and even
numbers. Such pattern is known as the Sierpinski’s triangle. In this
study, a presentation of Sierpinski-like patterns of the generalized
Pascal’s triangles is given. Applications related to those coefficients
of the binomial expansion (Pascal’s triangle), or polynomial
expansion (generalized Pascal’s triangles) can be in areas of
combinatorics, and probabilities.
Abstract: The recent instability in economy was found to be
influencing the situation in Malaysia whether directly or indirectly.
Taking that into consideration, the government needs to find the best
approach to balance its citizen’s socio-economic strata level urgently.
Through education platform is among the efforts planned and acted
upon for the purpose of balancing the effects of the influence,
through the exposure of social entrepreneurial activity towards youth
especially those in higher institution level. Armed with knowledge
and skills that they gained, with the support by entrepreneurial
culture and environment while in campus; indirectly, the students will
lean more on making social entrepreneurship as a career option when
they graduate. Following the issues of marketability and workability
of current graduates that are becoming dire, research involving how
far the willingness of student to create social innovation that
contribute to the society without focusing solely on personal gain is
relevant enough to be conducted. With that, this research is
conducted with the purpose of identifying the level of entrepreneurial
intention and social entrepreneurship among higher institution
students in Malaysia. Stratified random sampling involves 355
undergraduate students from five public universities had been made
as research respondents and data were collected through surveys. The
data was then analyzed descriptively using min score and standard
deviation. The study found that the entrepreneurial intention of higher
education students are on moderate level, however it is the contrary
for social entrepreneurship activities, where it was shown on a high
level. This means that while the students only have moderate level of
willingness to be a social entrepreneur, they are very committed to
created social innovation through the social entrepreneurship
activities conducted. The implication from this study can be
contributed towards the higher institution authorities in prediction the
tendency of student in becoming social entrepreneurs. Thus, the
opportunities and facilities for realizing the courses related to social
entrepreneurship must be created expansively so that the vision of
creating as many social entrepreneurs as possible can be achieved.
Abstract: A university-wide survey to obtain baseline data
regarding the perceptions of key terms related to e-learning and
distance learning among students, faculty and staff was conducted to
help achieve the goals of Princess Nourah bint Abdulrahman
University’s and the Kingdom of Saudi Arabia’s National Center for
e-learning and Distance Learning. This paper comprises a relevant
literature review, the survey methodology, preliminary data analysis,
discussion, and recommendations for further research. The major
findings indicate a deep and wide differentiation of understanding
among users of critical key terms.
Abstract: We present an approach to triangle mesh simplification
designed to be executed on the GPU. We use a quadric error metric
to calculate an error value for each vertex of the mesh and order all
vertices based on this value. This step is followed by the parallel
removal of a number of vertices with the lowest calculated error
values. To allow for the parallel removal of multiple vertices we use
a set of per-vertex boundaries that prevent mesh foldovers even when
simplification operations are performed on neighbouring vertices. We
execute multiple iterations of the calculation of the vertex errors,
ordering of the error values and removal of vertices until either a
desired number of vertices remains in the mesh or a minimum error
value is reached. This parallel approach is used to speed up the
simplification process while maintaining mesh topology and avoiding
foldovers at every step of the simplification.
Abstract: The maintenance of work rolls in hot strip processing
has been lengthy and difficult tasks for hot strip manufacturer
because heavy work rolls have to be taken out of the production line,
which could take hours. One way to increase the time between
maintenance is to improve the effectiveness of the work roll cooling
system such that the wear and tear more slowly occurs, while the
operation cost is kept low. Therefore, this study aims to improve the
work roll cooling system by providing the manufacturer the
relationship between the work-roll temperature reduced by cooling
and the water flow that can help manufacturer determining the more
effective water flow of the cooling system. The relationship is found
using simulation with a systematic process adjustment so that the
satisfying quality of product is achieved. Results suggest that the
manufacturer could reduce the water flow by 9% with roughly the
same performance. With the same process adjustment, the feasibility
of finishing-mill-stand reduction is also investigated. Results suggest
its possibility.
Abstract: Voltage level must be raised in order to deliver the
produced energy to the consumption zones with less loss and less
cost. Power transformers used to raise or lower voltage are important
parts of the energy transmission system. Power transformers used in
switchgear and power generation plants stay in human's intensive
habitat zones as a result of expanding cities. Accordingly, noise
levels produced by power transformers have begun more and more
important and they have established itself as one of the research field.
In this research, the noise cause on transformers has been
investigated, it's causes has been examined and noise measurement
techniques have been introduced. Examples of transformer noise test
results are submitted and precautions to be taken were discussed for
the purpose of decreasing of the noise which will occurred by
transformers.