Abstract: A local wastewater treatment plant (WWTP)
experiencing poor nitrification tracked down high level of
surfactants in the plant-s influent and effluent. The aims of this project were to assess the potential inhibitory effect of surfactants on activated sludge processes. The effect of the
presence of TergitolNP-9, TrigetolNP-7, Trigetol15-S-9,
dodecylbenzene sulphonate (SDBS) and sodium dodecyl
sulfate (SDS) on activated sludge oxygen uptake rate (OUR) and nitrification were assessed. The average concentration of non-ionic and anionic
surfactants in the influent to the local WWTP were 7 and 8.7 mg/L, respectively. Removal of 67% to 90% of the non-ionic and 93-99% of the anionic surfactants tested were measured. All surfactants tested showed inhibitory effects both on OUR
and nitrification. SDS incurred the lowest inhibition whereas
SDBS and NP-9 caused severe inhibition to OUR and
Nitrification. Activated sludge flocs sizes slightly decreased
after 3 hours contact with the surfactant present in the test.
The results obtained indicated that high concentrations of
surfactants are likely to have an adverse effect on the
performance of WWTPs utilizing activated sludge processes.
Abstract: In a pilot plant scale of a fluidized bed reactor, a
reduction reaction of sodium sulfate by natural gas has been
investigated. Natural gas is applied in this study as a reductant. Feed
density, feed mass flow rate, natural gas and air flow rate
(independent parameters)and temperature of bed and CO
concentration in inlet and outlet of reactor (dependent parameters)
were monitored and recorded at steady state. The residence time was
adjusted close to value of traditional reaction [1]. An artificial neural
network (ANN) was established to study dependency of yield and
carbon gradient on operating parameters. Resultant 97% accuracy of
applied ANN is a good prove that natural gas can be used as a
reducing agent. Predicted ANN model for relation between other
sources carbon gradient (accuracy 74%) indicates there is not a
meaningful relation between other sources carbon variation and
reduction process which means carbon in granule does not have
significant effect on the reaction yield.
Abstract: This paper presents the results of corrosion fatigue
crack growth behaviour of a Ni-Cr-Mn steel commonly used in
marine applications. The effect of mechanical variables such as
frequency and load ratio on fatigue crack growth rate at various
stages has been studied using compact tension (C(T)) specimens
along the rolling direction of steel plate under 3.5% saturated NaCl
aqueous environment. The significance of crack closure on corrosion
fatigue, and the validity of Elber-s empirical linear crack closure
model with the ASTM compliance offset method have been
examined.
Fatigue crack growth rate is higher and threshold stress intensities
are lower in aqueous environment compared to the lab air conditions.
It is also observed that the crack growth rate increases at lower
frequencies. The higher stress ratio promotes the crack growth. The
effect of oxidization and corrosion pit formation is very less as the
stress ratio is increased. It is observed that as stress ratios are
increased, the Elber-s crack closure model agrees well with the crack
closure estimated by the ASTM compliance offset method for tests
conducted at 5Hz frequency compared to tests conducted at 1Hz in
corrosive environment.
Abstract: The relationships between Proteolysis and soluble
calcium levels with hardness of cheese texture were investigated in
Iranian UF white cheese during 90 d ripening. Cheeses were sampled
in interior and exterior. Results showed that levels of proteolysis,
soluble calcium and hardness of cheese texture changed significantly
(p< 0.05) over ripening. Levels of proteolysis and hardness were
significantly (p< 0.05) different in interior and exterior zones of
cheeses. External zones of cheeses became softer and had higher
levels of proteolysis compared to internal zones during ripening. The
highest correlation coefficient (r2= 0.979; p
Abstract: The present work deals with the structural analysis of
turbine blades and modeling of turbine blades. A common failure
mode for turbine machines is high cycle of fatigue of compressor and
turbine blades due to high dynamic stresses caused by blade vibration
and resonance within the operation range of the machinery. In this
work, proper damping system will be analyzed to reduce the
vibrating blade. The main focus of the work is the modeling of under
platform damper to evaluate the dynamic analysis of turbine-blade
vibrations. The system is analyzed using Bond graph technique. Bond
graph is one of the most convenient ways to represent a system from
the physical aspect in foreground. It has advantage of putting together
multi-energy domains of a system in a single representation in a
unified manner. The bond graph model of dry friction damper is
simulated on SYMBOLS-shakti® software. In this work, the blades
are modeled as Timoshenko beam. Blade Vibrations under different
working conditions are being analyzed numerically.
Abstract: Where renewable energy sources, solar, hydro, wind are available the remote communities and businesses can be provided with the most reliable and affordable source of electrical energy. This paper presents a model of safari rest contains all the necessary services for the interested tourists who visit the safari Sinai desert. The PV energy system provides the rural energy needs of remote communities. A photovoltaic renewable energy system is designed to feed the global Ac and Dc electrical required load of this safari rest . The benefits of photovoltaic renewable energy at rural applications are its versatility and convenience. This model of safari rest must be taken in consideration by Egyptian Government as it will provide the tourism plane by new interested tourism field which put a big spot on Red sea area: El Ghordaka.
Abstract: As the network based technologies become
omnipresent, demands to secure networks/systems against threat
increase. One of the effective ways to achieve higher security is
through the use of intrusion detection systems (IDS), which are a
software tool to detect anomalous in the computer or network. In this
paper, an IDS has been developed using an improved machine
learning based algorithm, Locally Linear Neuro Fuzzy Model
(LLNF) for classification whereas this model is originally used for
system identification. A key technical challenge in IDS and LLNF
learning is the curse of high dimensionality. Therefore a feature
selection phase is proposed which is applicable to any IDS. While
investigating the use of three feature selection algorithms, in this
model, it is shown that adding feature selection phase reduces
computational complexity of our model. Feature selection algorithms
require the use of a feature goodness measure. The use of both a
linear and a non-linear measure - linear correlation coefficient and
mutual information- is investigated respectively
Abstract: Twenty four male Thai native × Anglo-Nubian
crossbred goats were randomly allocated to receive four treatments.
The experiment was conducted for four months and slaughtered that
the Longissimus dorsi muscle was collected for fatty acid analysis.
The results conclude that either castrated method or ages had no
significantly different on monounsaturated fatty acid (MUFA)
(P>0.05) except erucic acid (C22:1n9). Interaction between castrated
method and ages had significantly different in MUFA (P
Abstract: A new mechanism responsible for structural life
consumption due to resonant fatigue in turbine blades, or vanes, is
presented and explained. A rotating blade or vane in a gas turbine can
change its contour due to erosion and/or material build up, in any of
these instances, the surface pressure distribution occurring on the
suction and pressure sides of blades-vanes can suffer substantial
modification of their pressure and temperatures envelopes and flow
characteristics. Meanwhile, the relative rotation between the blade
and duct vane while the pressurized gas flows and the consequent
wake crossings, will induce a fluctuating thrust force or lift that will
excite the blade.
An actual totally used up set of vane-blade components in a HP
turbine power stage in a gas turbine is analyzed. The blade suffered
some material erosion mostly at the trailing edge provoking a
peculiar surface pressure envelope which evolved as the relative
position between the vane and the blade passed in front of each other.
Interestingly preliminary modal analysis for this eroded blade
indicates several natural frequencies within the aeromechanic power
spectrum, moreover, the highest frequency component is 94% of one
natural frequency indicating near resonant condition.
Independently of other simultaneously occurring fatigue cycles
(such as thermal, centrifugal stresses).
Abstract: Visfatin and apelin are two new adipokines that recently gained a special interest in diabetes research. This study was conducted to study the interplay between these two adipokines and their correlation with other inflammatory and biochemical parameters in type 2 diabetic (T2D) postmenopausal women with CAD. Visfatin and apelin were measured by enzyme-linked immunoassay (ELISA). Visfatin was found to be significantly higher in the following groups: T2D patients without CAD, non-obese and obese T2D patients with CAD when compared to control group. Apelin was found to be significantly lower in non-obese and obese T2D patients with CAD when compared to control group. Visfatin and apelin were found to be significantly associated with each other and with other biochemical parameters. The current study provides evidence for the interplay between visfatin and apelin through the inflammatory milieu characteristic of T2D and their possible role in the pathogenesis of CAD complication of T2D.
Abstract: Fuel cells have become one of the major areas of
research in the academia and the industry. The goal of most fish
farmers is to maximize production and profits while holding labor
and management efforts to the minimum. Risk of fish kills, disease
outbreaks, poor water quality in most pond culture operations,
aeration offers the most immediate and practical solution to water
quality problems encountered at higher stocking and feeding rates.
Many units of aeration system are electrical units so using a
continuous, high reliability, affordable, and environmentally friendly
power sources is necessary. Aeration of water by using PEM fuel cell
power is not only a new application of the renewable energy, but
also, it provides an affordable method to promote biodiversity in
stagnant ponds and lakes. This paper presents a new design and
control of PEM fuel cell powered a diffused air aeration system for a
shrimp farm in Mersa Matruh in Egypt. Also Artificial intelligence
(AI) techniques control is used to control the fuel cell output power
by control input gases flow rate. Moreover the mathematical
modeling and simulation of PEM fuel cell is introduced. A
comparison study is applied between the performance of fuzzy logic
control (FLC) and neural network control (NNC). The results show
the effectiveness of NNC over FLC.
Abstract: This study describes the methodology for the development of a validated in-vitro in-vivo correlation (IVIVC) for metoprolol tartrate modified release dosage forms with distinctive release rate characteristics. Modified release dosage forms were formulated by microencapsulation of metoprolol tartrate into different amounts of ethylcellulose by non-solvent addition technique. Then in-vitro and in-vivo studies were conducted to develop and validate level A IVIVC for metoprolol tartrate. The values of regression co-efficient (R2-values) for IVIVC of T2 and T3 formulations were not significantly (p
Abstract: This paper investigates the indices of a creative city in
Isfahan. Its main aim is to evaluate quantitative status of the creative
city indices in Isfahan city, analyze the dispersion and distribution of
these indices in Isfahan city. Concerning these, this study tries to
analyze the creative city indices in fifteen area of Isfahan through
secondary data, questionnaire, TOPSIS model, Shannon entropy and
SPSS. Based on this, the fifteen areas of Isfahan city have been
ranked with 12 factors of creative city indices. The results of studies
show that fifteen areas of Isfahan city are not equally benefiting from
creative indices and there is much difference between the areas of
Isfahan city.
Abstract: This survey of recent literature examines the link between growth and poverty. It is widely accepted that economic growth is a necessary condition for sustainable poverty reduction. But it is the fact that the economic growth of some countries has been pro-poor while others not. Some factors such as labor market, policies and demographic factors may lead to a weak relationship between economic performance and poverty rate. In this sense pro-growth policies should be pro-poor to increase the poverty alleviation effects of the growth. The purpose of this study is to review the recent studies on the effects of macroeconomic policies on poverty and inequality and to review the poverty analyses which examine the relationship between growth, poverty and inequality. Also this study provides some facts about the relationship between economic growth, inequality and poverty from Turkey. Keywordseconomic growth, inequality, macroeconomic policy, poverty
Abstract: Desert regions around the Nile valley in Upper Egypt
contain great extent of swelling soil. Many different comment
procedures of treatment of the swelling soils for construction such as
pre-swelling, load balance OR soil replacement. One of the measure
factors which affect the level of the aggressiveness of the swelling
soil is the direction of the infiltration water directions within the
swelling soils. In this paper a physical model was installed to
measure the effect of water on the swelling soil with replacement
using fatty acid distillation residuals (FADR) mixed with sand as
thick sand-FADR mixture to prevent the water pathway arrive to the
swelling soil. Testing program have been conducted on different
artificial samples with different sand to FADR contents ratios (4%,
6%, and 9%) to get the optimum value fulfilling the impermeable
replacement. The tests show that a FADR content of 9% is sufficient
to produce impermeable replacement.
Abstract: Organic farmers across Saskatchewan face soil
phosphorus (P) shortages. Due to the restriction on inputs in organic
systems, farmers rely on crop rotation and naturally-occurring
arbuscular mycorrhizal fungi (AMF) for plant P supply. Crop rotation
is important for disease, pest, and weed management. Crops that are
not colonized by AMF (non-mycorrhizal) can decrease colonization
of a following crop. An experiment was performed to quantify soil P
cycling in four cropping sequences under organic management and
determine if mustard (non-mycorrhizal) was delaying the
colonization of subsequent wheat. Soils from the four cropping
sequences were measured for inorganic soil P (Pi), AMF spore
density (SD), phospholipid fatty acid analysis (PLFA, for AMF
biomarker counts), and alkaline phosphatase activity (ALPase,
related to AMF metabolic activity). Plants were measured for AMF
colonization and P content and uptake of above-ground biomass. A
lack of difference in AMF activity indicated that mustard was not
depressing colonization. Instead, AMF colonization was largely
determined by crop type and crop rotation.
Abstract: Utilization of waste material in asphalt pavement
would be beneficial in order to find an alternative solution to increase
service life of asphalt pavement and reduce environmental pollution
as well. One of these waste materials is Polyethylene Terephthalate
(PET) which is a type of polyester material and is produced in a large
extent. This research program is investigating the effects of adding
waste PET particles into the asphalt mixture with a maximum size of
2.36 mm. Different percentages of PET were added into the mixture
during dry process. Gap-graded mixture (SMA 14) and PG 80-100
asphalt binder have been used for this study. To evaluate PET
reinforced asphalt mixture different laboratory investigations have
been conducted on specimens. Marshall Stability test was carried
out. Besides, stiffness modulus test and indirect tensile fatigue test
were conducted on specimens at optimum asphalt content. It was
observed that in many cases PET reinforced SMA mixture had better
mechanical properties in comparison with control mixture.
Abstract: The demands of taller structures are becoming imperative almost everywhere in the world in addition to the challenges of material and labor cost, project time line etc. This paper conducted a study keeping in view the challenging nature of high-rise construction with no generic rules for deflection minimizations and frequency control. The effects of cyclonic wind and provision of outriggers on 28-storey, 42-storey and 57-storey are examined in this paper and certain conclusions are made which would pave way for researchers to conduct further study in this particular area of civil engineering. The results show that plan dimensions have vital impacts on structural heights. Increase of height while keeping the plan dimensions same, leads to the reduction in the lateral rigidity. To achieve required stiffness increase of bracings sizes as well as introduction of additional lateral resisting system such as belt truss and outriggers is required.
Abstract: The paper is included within the framework of a
complex research program, which was initiated from the hypothesis
arguing on the existence of a correlation between pineal indolic and
peptide hormones and the somatic development rhythm, including
thus the epithalamium-epiphysis complex involvement. At birds,
pineal gland contains a circadian oscillator, playing a main role in the
temporal organization of the cerebral functions. The secretion of
pineal indolic hormones is characterized by a high endogenous
rhythmic alternation, modulated by the light/darkness (L/D)
succession and by temperature as well. The research has been carried
out using 100 chicken broilers - “Ross" commercial hybrid,
randomly allocated in two experimental batches: Lc batch, reared
under a 12L/12D lighting schedule and Lexp batch, which was photic
pinealectomised through continuous exposition to light (150 lux, 24
hours, 56 days). Chemical and physical features of the meat issued
from breast fillet and thighs muscles have been studied, determining
the dry matter, proteins, fat, collagen, salt content and pH value, as
well. Besides the variations of meat chemical composition in relation
with lighting schedule, other parameters have been studied: live
weight dynamics, feed intake and somatic development degree. The
achieved results became significant since chickens have 7 days of
age, some variations of the studied parameters being registered,
revealing that the pineal gland physiologic activity, in relation with
the lighting schedule, could be interpreted through the monitoring of
the somatic development technological parameters, usually studied
within the chicken broilers rearing aviculture practice.
Abstract: Porcine production in China represents approximately
the 50% of the worldwide pig production. Information about pig
husbandry characteristics in China and manure properties from sows
to fatteners in intensive pig farms are not broadly available for
scientific studies as it is a time consuming, expensive task and highly
inaccessible. This study provides a report about solid pig manures
(28% dry matter) in a commercial pig farm located in the peri-urban
area of Beijing as well as a general overview of the current pig
husbandry techniques including pig breeds, feeds, diseases, housing as
well as pig manure and wastewater disposal. The main results are
intended to serve as a literature source for young scientists in order to
understand the main composition of pig manures as well as to identify
the husbandry techniques applied in an intensive pig farm in Beijing.