Abstract: A model-free robust control (MFRC) approach is proposed for position control of robot manipulators in the state space. The control approach is verified analytically to be robust subject to uncertainties including external disturbances, unmodeled dynamics, and parametric uncertainties. There is a high flexibility to work on different systems including actuators by the use of the proposed control approach. The proposed control approach can guarantee the robustness of control system. A PUMA 560 robot driven by geared permanent magnet dc motors is simulated. The simulation results show a satisfactory performance for control system under technical specifications. KeywordsModel-free, robust control, position control, PUMA 560.
Abstract: Low carbon deep drawing steel DC 01 according to EN 10130-91 was nitrooxidized in dissociated ammonia at 580°C/45 min and consequently oxidised at 380°C/5 min in vapour of distilled water. Material after nitrooxidation had 54 % increase of yield point, 34 % increase of strength and 10-times increased resistance to atmospheric corrosion in comparison to the material before nitrooxidation. The microstructure of treated material consisted of thin ε-phase layer connected to layer containing precipitated massive needle shaped Fe4N - γ' nitrides. This layer passed to a diffusion layer consisting of fine irregular shaped Fe16N2 - α'' nitrides regularly dispersed in ferritic matrix. Fatigue properties were examined under bending load with frequency of 20 kHz and sinusoidal symmetric cycle. The results confirmed positive influence of nitrooxidation on fatigue properties as fatigue limit of treated material was double in comparison to untreated material.
Abstract: Supplier selection, in real situation, is affected by
several qualitative and quantitative factors and is one of the most
important activities of purchasing department. Since at the time of
evaluating suppliers against the criteria or factors, decision makers
(DMS) do not have precise, exact and complete information, supplier
selection becomes more difficult. In this case, Grey theory helps us
to deal with this problem of uncertainty. Here, we apply Technique
for Order Preference by Similarity to Ideal Solution (TOPSIS)
method to evaluate and select the best supplier by using interval
fuzzy numbers. Through this article, we compare TOPSIS with some
other approaches and afterward demonstrate that the concept of
TOPSIS is very important for ranking and selecting right supplier.
Abstract: Virtual engineering technology has undergone rapid progress in recent years and is being adopted increasingly by manufacturing companies of many engineering disciplines. There is an increasing demand from industry for qualified virtual engineers. The qualified virtual engineers should have the ability of applying engineering principles and mechanical design methods within the commercial software package environment. It is a challenge to the engineering education in universities which traditionally tends to lack the integration of knowledge and skills required for solving real world problems. In this paper, a case study shows some recent development of a MSc Mechanical Engineering course at Department of Engineering and Technology in MMU, and in particular, two units Simulation of Mechanical Systems(SMS) and Computer Aided Fatigue Analysis(CAFA) that emphasize virtual engineering education and promote integration of knowledge acquisition, skill training and industrial application.
Abstract: The influence of physical (external added weight) and
neurophysiological (fatigue) factors on static and dynamic balance in
sport related activities was typified statically by the Romberg test
(one foot flat, eyes open) and dynamically by jumping and hopping
in both horizontal and vertical directions. Twenty healthy males were
participated in this study. In Static condition, added weight increased
body-s inertia and therefore decreased body sway in AP direction
though not significantly. Dynamically, added weight significantly
increased body sway in both ML and AP directions, indicating
instability, and the use of the counter rotating segments mechanism to
maintain balance was demonstrated. Fatigue on the other hand
significantly increased body sway during static balance as a
neurophysiological adaptation primarily to the inverted pendulum
mechanism. Dynamically, fatigue significantly increased body sway
in both ML and AP directions again indicating instability but with a
greater use of counter rotating segments mechanism. Differential
adaptations for each of the two balance mechanisms (inverted
pendulum and counter rotating segments) were found between one
foot flat and two feet flat dynamic conditions, as participants relied
more heavily on the first in the one foot flat conditions and relied
more on the second in the two feet flat conditions.
Abstract: This study aimed to evaluate the muscularity and tissue composition of 24 legs of Ile de France lambs. They were fed with diets containing “in nature" or hydrolyzed sugarcane with 0.6% of calcium oxide in aerobic and anaerobic environments. Animals entered the trial at 15 and were slaughtered at 32 kg of body weight. The leg tissue composition, as well as muscularity (0.47), muscle:bone (6.66) and muscle:fat (4.25) were not affected (P>0.05) by treatments. The proportions found were: 67.62% for muscle, 17.52% for bone and 10.15% for fat. In relation to lambs fed with “in nature" sugarcane, hydrolyzed sugarcane with calcium oxide in aerobic and anaerobic environments did not affect muscularity and leg tissue composition of lambs.
Abstract: With the development of ubiquitous computing,
current user interaction approaches with keyboard, mouse and pen
are not sufficient. Due to the limitation of these devices the useable
command set is also limited. Direct use of hands as an input device is
an attractive method for providing natural Human Computer
Interaction which has evolved from text-based interfaces through 2D
graphical-based interfaces, multimedia-supported interfaces, to fully
fledged multi-participant Virtual Environment (VE) systems.
Imagine the human-computer interaction of the future: A 3Dapplication
where you can move and rotate objects simply by moving
and rotating your hand - all without touching any input device. In this
paper a review of vision based hand gesture recognition is presented.
The existing approaches are categorized into 3D model based
approaches and appearance based approaches, highlighting their
advantages and shortcomings and identifying the open issues.
Abstract: In the present study, the effect of ferrous sulfate concentration and total solids on bioleaching of heavy metals from sewage sludge has been examined using indigenous iron-oxidizing microorganisms. The experiments on effects of ferrous sulfate concentrations on bioleaching were carried out using ferrous sulfate of different concentrations (5-20 g L-1) to optimize the concentration of ferrous sulfate for maximum bioleaching. A rapid change in the pH and ORP took place in first 2 days followed by a slow change till 16th day in all the sludge samples. A 10 g L-1 ferrous sulfate concentration was found to be sufficient in metal bioleaching in the following order: Zn: 69%>Cu: 52%>Cr: 46%>Ni: 45. Further, bioleaching using 10 g/L ferrous sulfate was found to be efficient up to 20 g L-1 sludge solids concentration. The results of the present study strongly indicate that using 10 g L-1 ferrous sulfate indigenous iron-oxidizing microorganisms can bring down pH to a value needed for significant metal solubilization.
Abstract: This paper presents the analysis of duct design using
static and dynamic approaches. The static approach is used to find
out applicability between the design and material applied. The
material used in this paper is Thermoplastic Olefins (TPO). For the
dynamic approach, the focusing is only on the CFD simulations. The
fatigue life in this design and material applied also covered.
Abstract: Ten lactating multiparous Holstein cows were used in
a cross-over design with two dietary treatments and 28-d periods
(with 14 d as an adaptation) to study the effect of restaurant fat on
milk production and composition. Each cow was offered 14.7 kg
DM /d of the basal concentrate diet based on barley and corn (crude
protein = 17.7%, neutral detergent fiber = 23.5%, and acid detergent
fiber = 5.8% of dry matter) with free access to alfalfa. Dietary
treatments were arranged as supplying each cow with 0 (CONTROL)
or 150 g/day (RF) of restaurant fat. Supplemental RF did not
significantly (P > 0.25) affect milk yield, composition, and
composition yields, except for milk fat contents. Milk fat contents
were depressed (P < 0.05) with supplemental RF. Our results indicate
that RF could depress milk fat without affecting milk yield and that
the depression in milk fat in response to RF precedes the depression
in milk yield.
Abstract: A combination of photosynthetic bacteria along with
anaerobic acidogenic bacteria is an ideal option for efficient
hydrogen production. In the present study, the optimum
concentration of substrates for the growth of Rhodobacter
sphaeroides was found by response surface methodology. The
optimum combination of three individual fatty acids was determined
by Box Behnken design. Increase of volatile fatty acid concentration
decreased the growth. Combination of sodium acetate and sodium
propionate was most significant for the growth of the organism. The
results showed that a maximum biomass concentration of 0.916 g/l
was obtained when the concentrations of acetate, propionate and
butyrate were 0.73g/l,0.99g/l and 0.799g/l, respectively. The growth
was studied under an optimum concentration of volatile fatty acids
and at a light intensity of 3000 lux, initial pH of 7 and a temperature
of 35°C.The maximum biomass concentration of 0.92g/l was
obtained which verified the practicability of this optimization.
Abstract: In this study arsenate [As(V)] removal from drinking water by coagulation process was investigated. Ferric chloride (FeCl3.6H2O) and ferrous sulfate (FeSO4.7H2O) were used as coagulant. The effects of major operating variables such as coagulant dose (1–30 mg/L) and pH (5.5–9.5) were investigated. Ferric chloride and ferrous sulfate were found as effective and reliable coagulant due to required dose, residual arsenate and coagulant concentration. Optimum pH values for maximum arsenate removal for ferrous sulfate and ferric chloride were found as 8 and 7.5. The arsenate removal efficiency decreased at neutral and acidic pH values for Fe(II) and at the high acidic and high alkaline pH for Fe(III). It was found that the increase of coagulant dose caused a substantial increase in the arsenate removal. But above a certain ferric chloride and ferrous sulfate dosage, the increase in arsenate removal was not significant. Ferric chloride and ferrous sulfate dose above 8 mg/L slightly increased arsenate removal.
Abstract: In this paper, the effect of bolt clamping force on the fatigue behavior of bolted single lap joints of aluminum alloy 2024- T3 have been studied using numerical finite element method. To do so, a three dimensional model according to the bolted single lap joint has been created and numerical analysis has been carried out using finite element based package. Then the stress distribution and also the slip amplitudes have been calculated in the critical regions and the outcome have been compared with the available experimental fatigue tests results. The numerical results show that in low applied clamping force, the fatigue failure of the specimens occur around the stress concentration location (the bolted hole edge) due to the tensile stresses and thus fatigue crack propagation, but with increase of the clamping force, the fatigue life increases and the cracks nucleate and propagate far from the hole edge because of fretting fatigue. In other words, with the further increase of clamping force value of the joint, the fatigue life reduces due to occurrence of the fretting fatigue in the critical location where the slip amplitude is within its critical occurs earlier.
Abstract: Structured phospholipids from commercial soybean
lecithin with oil enriched omega-3 fatty acid form by product of tuna
canning is alternative procedure to provides the stability of omega-3
fatty acid structure and increase these bioactive function in
metabolism. Best treatment condition was obtain in 18 hours
acidolysis reaction with 30% enzyme concentration, which EPADHA
incorporation level was 127,47 mg/g and incorporation
percentage of EPA-DHA was 51,04% at phospholipids structure.
This structured phospolipids could reduce atherosclerosis risk in
male Sprague dawley rat. Provision of structured phospholipids has
significant effect (α = 0.05) on changes in lipid profile, intima-media
thickness of aorta rats (male Sprague dawley) fed atherogenic diet.
Structured phospholipids intake can lower total cholesterol 78.36
mg/dL, total triglycerides 94,57 mg/dL, LDL levels 87.08 mg/dL and
increased HDL level as much as 12,64 mg/dL in 10 weeks cares.
Structured phospholipids intake also can prevent the thickening of
the intima-media layer of the aorta.
Abstract: Background: Blunt aortic trauma (BAT) includes
various morphological changes that occur during deceleration,
acceleration and/or body compression in traffic accidents. The
various forms of BAT, from limited laceration of the intima to
complete transection of the aorta, depends on the force acting on the
vessel wall and the tolerance of the aorta to injury. The force depends
on the change in velocity, the dynamics of the accident and of the
seating position in the car. Tolerance to aortic injury depends on the
anatomy, histological structure and pathomorphological alterations
due to aging or disease of the aortic wall.
An overview of the literature and medical documentation reveals
that different terms are used to describe certain forms of BAT, which
can lead to misinterpretation of findings or diagnoses. We therefore,
propose a classification that would enable uniform systematic
screening of all forms of BAT. We have classified BAT into three
morphologycal types: TYPE I (intramural), TYPE II (transmural) and
TYPE III (multiple) aortic ruptures with appropriate subtypes.
Methods: All car accident casualties examined at the Institute of
Forensic Medicine from 2001 to 2009 were included in this
retrospective study. Autopsy reports were used to determine the
occurrence of each morphological type of BAT in deceased drivers,
front seat passengers and other passengers in cars and to define the
morphology of BAT in relation to the accident dynamics and the age
of the fatalities.
Results: A total of 391 fatalities in car accidents were included in
the study. TYPE I, TYPE II and TYPE III BAT were observed in
10,9%, 55,6% and 33,5%, respectively. The incidence of BAT in
drivers, front seat and other passengers was 36,7%, 43,1% and
28,6%, respectively. In frontal collisions, the incidence of BAT was
32,7%, in lateral collisions 54,2%, and in other traffic accidents
29,3%. The average age of fatalities with BAT was 42,8 years and of
those without BAT 39,1 years.
Conclusion: Identification and early recognition of the risk factors
of BAT following a traffic accident is crucial for successful treatment
of patients with BAT. Front seat passengers over 50 years of age who
have been injured in a lateral collision are the most at risk of BAT.
Abstract: Cardiovascular disease mostly in the form of atherosclerosis is responsible for 30% of all world deaths amounting to 17 million people per year. Atherosclerosis is due to the formation of plaque. The fatty plaque may be at risk of rupture, leading typically to stroke and heart attack. The plaque is usually associated with a high degree of lumen reduction, called a stenosis. The initiation and progression of the disease is strongly linked to the hemodynamic environment near the vessel wall. The aim of this study is to validate the flow of blood mimic through an arterial stenosis model with computational fluid dynamics (CFD) package. In experiment, an axisymmetric model constructed consists of contraction and expansion region that follow a mathematical form of cosine function. A 30% diameter reduction was used in this study. Particle image velocimetry (PIV) was used to characterize the flow. The fluid consists of rigid spherical particles suspended in waterglycerol- NaCl mixture. The particles with 20 μm diameter were selected to follow the flow of fluid. The flow at Re=155, 270 and 390 were investigated. The experimental result is compared with FLUENT simulated flow that account for viscous laminar flow model. The results suggest that laminar flow model was sufficient to predict flow velocity at the inlet but the velocity at stenosis throat at Re =390 was overestimated. Hence, a transition to turbulent regime might have been developed at throat region as the flow rate increases.
Abstract: A thin layer on the component surface can be found
with high tensile residual stresses, due to turning operations, which
can dangerously affect the fatigue performance of the component. In
this paper an analytical approach is presented to reconstruct the
residual stress field from a limited incomplete set of measurements.
Airy stress function is used as the primary unknown to directly solve
the equilibrium equations and satisfying the boundary conditions. In
this new method there exists the flexibility to impose the physical
conditions that govern the behavior of residual stress to achieve a
meaningful complete stress field. The analysis is also coupled to a
least squares approximation and a regularization method to provide
stability of the inverse problem. The power of this new method is
then demonstrated by analyzing some experimental measurements
and achieving a good agreement between the model prediction and
the results obtained from residual stress measurement.
Abstract: Yogurts are prepared by fermenting milk with bacterial cultures consisting of a mixture of Streptococcus ssp. thermophilus and Lactobacillus delbrueckii ssp. bulgaricus. The main aim of this investigation was to develop a majority goat yogurt, with the addition of sheep milk in order to have a final product with good physicochemical quality properties and sensorial attributes. Four types of yogurts were prepared presenting the following proportion of goat and sheep milk respectively: C100 – 100%; C80 – 80%/20%; C60 – 60%/40%; C50 – 50%/50%. The goat milk was from the Serrana Jarmelista breed and the sheep milk from the Serra da Estrela breed. The inclusion of sheep milk improved attractiveness to consumers, and it also improved the nutritional value of the product, mainly the fatty acid and mineral contents. The C50 yogurt was preferred by 28% of the panellists, followed by the C100 with 16% and the commercial cow yogurt was 40% of preferences.
Abstract: Traditionally, project scheduling and material planning have been treated independently. In this research, a mixed integer programming model is presented to integrate project scheduling and materials ordering problems. The goal is to minimize the total material holding and ordering costs. In addition, an efficient metaheuristic algorithm is proposed to solve the model. The proposed algorithm is computationally tested, the results are analyzed, and conclusions are given.
Abstract: We have modeled the effect of a graded band gap
window on the performance of a single junction AlxGa1-xAs/GaAs
solar cell. First, we study the electrical characteristics of a single
junction AlxGa1-xAs/GaAs solar cell, by employing an optimized
structure for this solar cell, we show that grading the band gap of the
window can increase the conversion efficiency of the solar cell by
about 1.5%, and can also improve the quantum efficiency of the solar
cell especially at shorter wavelengths.