Abstract: Verification of vented wooden façade system with
bonded joints is presented in this paper. The potential of bonded
joints is studied and described in more detail. The paper presents the results of an experimental and theoretical research about the effects of freeze cycling on the bonded joint. For the purpose of tests spruce
timber profiles were chosen for the load bearing substructure. Planks from wooden plastic composite and Siberian larch are representing facade cladding. Two types of industrial polyurethane adhesives intended for structural bonding were selected. The article is focused on the preparation as well as on the subsequent curing and conditioning of test samples. All test samples were subjected to 15 cycles that represents sudden temperature changes, i.e. immersion in a water bath at (293.15 ± 3) K for 6 hours and subsequent freezing to (253.15 ± 2) K for 18 hours. Furthermore, the retention of bond strength between substructure and cladding wastested and strength in shear was determined under tensile stress.Research data indicate that little, if any, damage to the bond results from freezingcycles. Additionally, the suitability of selected group of adhesives in combination with timber substructure was confirmed.
Abstract: Dental porcelain composites reinforced and toughened
by 20 wt.% tetragonal zirconia (3Y-TZP) were processed by hot
pressing at 1000°C. Two types of particles were tested: yttriastabilized
zirconia (ZrO2–3%Y2O3) agglomerates and pre-sintered
yttria-stabilized zirconia (ZrO2–3%Y2O3) particles. The composites
as well as the reinforcing particles were analyzed by the means of
optical and Scanning Electron Microscopy (SEM), Energy Dispersion
Spectroscopy (EDS) and X-Ray Diffraction (XRD). The mechanical
properties were obtained by the transverse rupture strength test. Wear
tests were also performed on the composites and monolithic
porcelain. The best mechanical results were displayed by the
porcelain reinforced with the pre-sintered ZrO2–3%Y2O3
agglomerates.
Abstract: Depositional environment and source potential of the
different organic-rich levels of Devonian age (up to 990m thick) from
the onshore EC-1 well (Southern Tunisia) were investigated based on
the analysis of more than 130 cutting samples by different
geochemical techniques (Rock-Eval pyrolysis, GC-MS). The
obtained results including Rock Eval Pyrolysis data and biomarker
distribution (terpanes, steranes and aromatics) have been used to
describe the depositional environment and to assess the thermal
maturity of the Devonian organic matter. These results show that the
Emsian deposits exhibit poor to fair TOC contents. The associated
organic matter is composed of mixed kerogen (type II/III), as
indicated by the predominance of C29 steranes over C27 and C28
homologous, that was deposited in a slightly reduced environment
favoring organic matter preservation. Thermal maturity assessed from
Tmax, TNR and MPI-1 values shows a mature stage of organic
matter. The Middle Devonian (Eifelian) shales are rich in type II
organic matter that was deposited in an open marine depositional
environment. The TOC values are high and vary between 2 and 7%
indicating good to excellent source rock. The relatively high HI
values (reaching 547 mg HC/g TOC) and the low values of t19/t23
tricyclic terpane ratio (< 0.2) confirm the marine origin of the organic
matter (type II). During the Upper Devonian, the organic matter was
deposited under variable redox conditions, oxic to suboxic which is
clearly indicated by the low C35/C34 hopanes ratio, immature to
marginally mature with the vitrinite reflectance ranging from 0.5 to
0.7 Ro and Tmax value of 426°C-436 °C and the TOC values range
between 0.8% to 4%.
Abstract: Taking into account the significance of measuring the
daily use of the study space in the libraries in order to develop and
reorganize the space for enhancing the efficiency of the study space,
the current study aimed to apply GIS in analyzing the study halls of
the Central Library and Document Center of Tehran University in
order to determine how study desks and chairs were used by the
students. The study used a combination of survey-descriptive and
system design method. In order to gather the required data, surveydescriptive
method was used. For implementing and entering data
into ArcGIS and analyzing the data and displaying the results on the
maps of the study halls of the library, system design method was
utilized. The design of the spatial database of the use of the study
halls was measured through the extent of occupancy of the space by
the library users and the maps of the study halls of the central library
of Tehran University as the case study. The results showed that
Abooreyhan hall had the highest rate of occupancy of the desks and
chairs compared to the other halls. The Hall of Science and
Technology, with an average occupancy rate of 0.39 for the tables
represented the lowest number of users and Rashid al-Dins hall, and
Science and Technology hall with an average occupancy rate (0.40)
had the lowest number of users for seats. In this study, the
comparison of the space occupied at different periods in the morning,
evenings, afternoons, and several months was performed through
GIS. This system analyzed the space relationships effectively and
efficiently. The output of this study would be used by administrators
and librarians to determine the exact extent of use of the equipment
of the study halls and librarians can use the output map to design the
space more efficiently at the library.
Abstract: In this paper, a numerical simulation of a finned store
separating from a wing-pylon configuration has been studied and
validated. A dynamic unstructured tetrahedral mesh approach is
accomplished by using three grid sizes to numerically solving the
discretized three dimensional, inviscid and compressible Euler
equations. The method used for computations of separation of an
external store assuming quasi-steady flow condition. Computations of
quasi-steady flow have been directly coupled to a six degree-offreedom
(6DOF) rigid-body motion code to generate store
trajectories. The pressure coefficients at four different angular cuts
and time histories of various trajectory parameters and wing pressure
distribution during the store separation are compared for every grid
size with published experimental data.
Abstract: Increasing prevalence of childhood obesity has
increased the interest in early and late indicators of gaining weight.
Cell blood counts may be indicators of pro-inflammatory states. The
aim was to evaluate associations of hematological parameters,
including hematocrit (HTC), hemoglobin, blood cell counts and their
indices with the degree of obesity in pediatric population. A total of
249; -139 morbidly obese (MO), 82 healthy normal weight (NW) and
28 overweight (OW) children were included into the scope of the
study. WHO BMI-for age percentiles were used to form age- and sexmatched
groups. Informed consent forms and the Ethics Committee
approval were obtained. Anthropometric measurements were
performed. Hematological parameters were determined. Statistical
analyses were performed using SPSS. The degree for statistical
significance was p≤0.05. Significant differences (p=0.000) between
waist-to-hip ratios and head-to- neck ratios (hnrs) of MO and NW
children were detected. A significant difference between hnrs of OW
and MO children (p=0.000) was observed. Red cell distribution width
(RDW) was higher in OW children than NW group (p=0.030). Such
finding couldn’t be detected between MO and NW groups. Increased
RDW was prominent in OW children. The decrease in mean
corpuscular hemoglobin concentration (MCHC) values in MO
children was sharper than the values in OW children (p=0.006 vs
p=0.042) compared to those in NW group. Statistically higher HTC
levels were observed between MO-NW (p=0.014), but none between
OW-NW. Though the cause-effect relationship between obesity and
erythrocyte indices still needs further investigation, alterations in
RDW, HTC, MCHC during obesity may be of significance in the
early life.
Abstract: There are several possibilities of reducing the required
amount of cement in concrete production. Natural zeolite is one of
the raw materials which can partly substitute Portland cement. The
effort to reduce the amount of Portland cement used in concrete
production is brings both economical as well as ecological benefits.
The paper presents the properties of concrete containing natural
zeolite as an active admixture in the concrete which partly substitutes
Portland cement. The properties discussed here bring information
about the basic mechanical properties and frost resistance of concrete
containing zeolite. The properties of concretes with the admixture of
zeolite are compared with a reference concrete with no content of
zeolite. The properties of the individual concretes are observed for
360 days.
Abstract: In the current work, a three-dimensional geometry of a
75% stenosed blood vessel is analyzed. Large eddy simulation (LES)
with the help of a dynamic subgrid scale Smagorinsky model is
applied to model the turbulent pulsatile flow. The geometry, the
transmural pressure and the properties of the blood and the elastic
boundary were based on clinical measurement data. For the flexible
wall model, a thin solid region is constructed around the 75%
stenosed blood vessel. The deformation of this solid region was
modelled as a deforming boundary to reduce the computational cost
of the solid model. Fluid-structure interaction is realized via a twoway
coupling between the blood flow modelled via LES and the
deforming vessel. The information of the flow pressure and the wall
motion was exchanged continually during the cycle by an arbitrary
Lagrangian-Eulerian method. The boundary condition of current time
step depended on previous solutions. The fluctuation of the velocity
in the post-stenotic region was analyzed in the study. The axial
velocity at normalized position Z=0.5 shows a negative value near
the vessel wall. The displacement of the elastic boundary was
concerned in this study. In particular, the wall displacement at the
systole and the diastole were compared. The negative displacement at
the stenosis indicates a collapse at the maximum velocity and the
deceleration phase.
Abstract: Background - The TrendCare Patient Dependency
System is currently used by a large number of maternity Services
across Australia, New Zealand and Singapore. In 2012, 2013 and
2014 validation studies were initiated in all three countries to validate
the acuity tools used for women in labour, and postnatal mothers and
babies. This paper will present the findings of the validation study.
Aim - The aim of this study was to; identify if the care hours
provided by the TrendCare acuity system was an accurate reflection
of the care required by women and babies; obtain evidence of
changes required to acuity indicators and/or category timings to
ensure the TrendCare acuity system remains reliable and valid across
a range of maternity care models in three countries.
Method - A non-experimental action research methodology was
used across maternity services in four District Health Boards in New
Zealand, a large tertiary and a large secondary maternity service in
Singapore and a large public maternity service in Australia.
Standardised data collection forms and timing devices were used to
collect midwife contact times, with women and babies included in the
study. Rejection processes excluded samples when care was not
completed/rationed, and contact timing forms were incomplete. The
variances between actual timed midwife/mother/baby contact and the
TrendCare acuity category times were identified and investigated.
Results - Thirty two (88.9%) of the 36 TrendCare acuity category
timings, fell within the variance tolerance levels when compared to
the actual timings recorded for midwifery care. Four (11.1%)
TrendCare categories provided less minutes of care than the actual
timings and exceeded the variance tolerance level. These were all
night shift category timings. Nine postnatal categories were not able
to be compared as the sample size for these categories was
statistically insignificant. 100% of labour ward TrendCare categories
matched actual timings for midwifery care, all falling within the
variance tolerance levels.
The actual time provided by core midwifery staff to assist lead
maternity carer (LMC) midwives in New Zealand labour wards
showed a significant deviation to previous studies. The findings of
the study demonstrated the need for additional time allocations in
TrendCare to accommodate an increased level of assistance given to
LMC midwives.
Conclusion - The results demonstrated the importance of regularly
validating the TrendCare category timings with actual timings of the
care hours provided. It was evident from the findings that variances
to models of care and length of stay in maternity units have increased
midwifery workloads on the night shift. The level of assistance
provided by the core labour ward staff to the LMC midwife has
increased substantially.
Outcomes - As a consequence of this study, changes were made to
the night duty TrendCare maternity categories, additional acuity
indicators were developed and times for assisting LMC midwives in
labour ward increased. The updated TrendCare version was delivered
to maternity services in 2014.
Abstract: Employer branding is considered as a useful tool for
addressing the global-local problem facing complex organisations
that have operations scattered across the globe and face challenges of
dealing with the local environment alongside. Despite being an
established field of study within the Western developed world, there
is little empirical evidence concerning the relevance of employer
branding to global companies that operate in the under-developed
economies. This paper fills this gap by gaining rich insight into the
implementation of employer branding programs in a foreign
multinational operating in Pakistan dealing with the global-local
problem. The study is qualitative in nature and employs semistructured
and focus group interviews with senior/middle managers
and local frontline employees to deeply examine the phenomenon in
case organisation. Findings suggest that authenticity is required in
employer brands to enable them to respond to the local needs thereby
leading to the resolution of the global-local problem. However, the
role of signaling theory is key to the development of authentic
employer brands as it stresses on the need to establish an efficient and
effective signaling environment where in signals travel in both
directions (from signal designers to receivers and backwards) and
facilitate firms with the global-local problem. The paper also
identifies future avenues of research for the employer branding field.
Abstract: Predicting the collapse potential of a structure during
earthquakes is an important issue in earthquake engineering. Many
researchers proposed different methods to assess the collapse
potential of structures under the effect of strong ground motions.
However most of them did not consider degradation and softening
effect in hysteretic behavior. In this study, collapse potential of
SDOF systems caused by dynamic instability with stiffness and
strength degradation has been investigated. An equation was
proposed for the estimation of collapse period of SDOF system which
is a limit value of period for dynamic instability. If period of the
considered SDOF system is shorter than the collapse period then the
relevant system exhibits dynamic instability and collapse occurs.
Abstract: This article presents modeling studies of NiAl alloy
under solid-particle erosion and liquid-drop erosion. In the
solid-particle erosion simulation, attention is paid to the oxide scale
thickness variation on the alloy in high-temperature erosion
environments. The erosion damage is assumed to be deformation wear
and cutting wear mechanisms, incorporating the influence of the oxide
scale on the eroded surface; thus the instantaneous oxide thickness is
the result of synergetic effect of erosion and oxidation. For liquid-drop
erosion, special interest is in investigating the effects of drop velocity
and drop size on the damage of the target surface. The models of
impact stress wave, mean depth of penetration, and maximum depth of
erosion rate (Max DER) are employed to develop various maps for
NiAl alloy, including target thickness vs. drop size (diameter), rate of
mean depth of penetration (MDRP) vs. drop impact velocity, and
damage threshold velocity (DTV) vs. drop size.
Abstract: The design philosophy of building structure has been
changing time to time. The reason for this is because of an increase of
human inertest, an improved building materials and technology that
will impact how we live, to speed up construction period and natural
effect which includes earthquake disasters and environmental effect.
One technique which takes in to account the above case is using a
prefabricable structural system. In which each and every structural
element is designed and prefabricated and assembled on a site so that
the construction speed is increased and the environmental impact is
also enhanced. This system has an immense advantage such as: reduce
construction cost, reusable, recyclable, speed up construction period
and less environmental effect. In this study, it is tried to present some
of the developed and evaluated structural elements of building
structures.
Abstract: In general, classical methods such as maximum
likelihood (ML) and least squares (LS) estimation methods are used
to estimate the shape parameters of the Burr XII distribution.
However, these estimators are very sensitive to the outliers. To
overcome this problem we propose alternative robust estimators
based on the M-estimation method for the shape parameters of the
Burr XII distribution. We provide a small simulation study and a real
data example to illustrate the performance of the proposed estimators
over the ML and the LS estimators. The simulation results show that
the proposed robust estimators generally outperform the classical
estimators in terms of bias and root mean square errors when there
are outliers in data.
Abstract: In general, codes and regulations consider seismic
loads only for completed structures of the bridges while, evaluation
of incomplete structure of bridges, especially those constructed by
free cantilever method, under these loads is also of great importance.
Hence, this research tried to study the behavior of incomplete
structure of common bridge type (box girder bridge), in construction
phase under vertical seismic loads. Subsequently, the paper provided
suitable guidelines and solutions to resist this destructive
phenomenon. Research results proved that use of preventive methods
can significantly reduce the stresses resulted from vertical seismic
loads in box cross sections to an acceptable range recommended by
design codes.
Abstract: High performance turf reinforcement mat (HPTRM) is
one of the most advanced flexible armoring technologies for severe
erosion challenges. The effect of turbulence on the slope stability of
an earthen levee strengthened by high performance turf reinforcement
mat (HPTRM) is investigated in this study for combined storm surge
and wave overtopping conditions. The results show that turbulence
has strong influence on the slope stability during the combined storm
surge and wave overtopping conditions. Among the surge height,
peak wave force and turbulent force. The turbulent force has the
ability to stabilize the earthen levee at the large wave force the
turbulent force has strongest effect on the FS. The surge storm acts as
an independent force on the slope stability of the earthen levee. It just
adds to the effects of the turbulent force and wave force on the slope
stability of HPTRM strengthened levee.
Abstract: This paper presents a study of SIW circuits (Substrate
Integrated Waveguide) with a rigorous and fast original approach
based on Iterative process (WCIP). The theoretical suggested study is
validated by the simulation of two different examples of SIW
circuits. The obtained results are in good agreement with those of
measurement and with software HFSS.
Abstract: This paper presents effects of distilled water, seawater
and sustained bending strains of 30% and 50% ultimate strain at
room temperature, on the durability of unidirectional pultruded
carbon fiber reinforced polymer (CFRP) plates. In this study,
dynamic mechanical analyzer (DMA) was used to investigate the
synergic effects of the immersions and bending strains on the viscoelastic
properties of (CFRP) such as storage modulus, tan delta and
glass transition temperature. The study reveals that the storage
modulus and glass transition temperature increase while tan delta
peak decreases in the initial stage of both immersions due to the
progression of curing. The storage modulus and Tg subsequently
decrease and tan delta increases due to the matrix plasticization. The
blister induced damages in the unstrained seawater samples enhance
water uptake and cause more serious degradation of Tg and storage
modulus than in water immersion. Increasing sustained bending
decreases Tg and storage modulus in a long run for both immersions
due to resin matrix cracking and debonding. The combined effects of
immersions and strains are not clearly reflected due to the statistical
effects of DMA sample sizes and competing processes of molecular
reorientation and postcuring.
Abstract: It is well known that in recent years magnetic
materials have received increased attention due to their properties.
For this reason a significant number of patents that were published
during the last decade are oriented towards synthesis and study of
such materials. The aim of this work is to create and study ferrite
nanocrystalline materials with spinel structure, using sol-gel
technology with participation of auto-combustion. This method is
perspective in that it is a cheap and low-temperature technique that
allows for the fine control on the product’s chemical composition.
Abstract: The biodegradable family of polymers
polyhydroxyalkanoates is an interesting substitute for convectional
fossil-based plastics. However, the manufacturing and environmental
impacts associated with their production via intracellular bacterial
fermentation are strongly dependent on the raw material used and on
energy consumption during the extraction process, limiting their
potential for commercialization. Industrial wastewater is studied in
this paper as a promising alternative feedstock for waste valorization.
Based on results from laboratory and pilot-scale experiments, a
conceptual process design, techno-economic analysis and life cycle
assessment are developed for the large-scale production of the most
common type of polyhydroxyalkanoate, polyhydroxbutyrate.
Intracellular polyhydroxybutyrate is obtained via fermentation of
microbial community present in industrial wastewater and the
downstream processing is based on chemical digestion with
surfactant and hypochlorite. The economic potential and
environmental performance results help identifying bottlenecks and
best opportunities to scale-up the process prior to industrial
implementation. The outcome of this research indicates that the
fermentation of wastewater towards PHB presents advantages
compared to traditional PHAs production from sugars because the
null environmental burdens and financial costs of the raw material in
the bioplastic production process. Nevertheless, process optimization
is still required to compete with the petrochemicals counterparts.