Abstract: Soils are normally dried in either a convection oven or stove. Laboratory moisture content testing indicated that the typical drying durations for a convection oven were, 24 hours. The purpose of this study was to determine the accuracy and soil drying duration of both, moisture content and liquid limit using microwave radiation. The soils were tested with both, convection and microwave ovens. The convection oven was considered to produce the true values for both, natural moisture content and liquid limit of soils; it was, therefore, used as a basis for comparison for the results of the microwave ovens. The samples used in this study were obtained from different projects of Consulting Engineering Bureau of College of Engineering of Sulaimani University. These samples were collected from different locations and at the different depths and consist mostly of brown and light brown clay and silty clay. A total of 102 samples were prepared. 26 of them were tested for natural moisture determination, while the other 76 were used for liquid limits determination
Abstract: The aim of the study was to evaluate the effect of
texturizers on the rheological properties of the apple mass and
desserts made from various raw materials. The apple varieties -
‘Antonovka’, ‘Baltais Dzidrais’, and ‘Zarja Alatau’ harvested in
Latvia, were used for the experiment. The apples were processed in a
blender unpeeled for obtaining a homogenous mass. The apple mass
was analyzed fresh and after storage at –18ºC. Both fresh and thawed
apple mass samples with added gelatin, xantan gum, and sodium
carboxymethylcellulose were whisked obtaining dessert. Pectin, pH
and soluble dry matter of the product were determined. Apparent
viscosity was measured using a rotational viscometer DV–III Ultra.
Pectin content in frozen apple mass decreased significantly (p
Abstract: Vacuum membrane distillation (VMD) process can be
used for water purification or the desalination of salt water. The
process simply consists of a flat sheet hydrophobic micro porous
PTFE membrane and diaphragm vacuum pump without a condenser
for the water recovery or trap. The feed was used aqueous NaCl
solution. The VMD experiments were performed to evaluate the heat
and mass transfer coefficient of the boundary layer in a membrane
module. The only operating parameters are feed inlet temperature,
and feed flow rate were investigated. The permeate flux was strongly
affected by the feed inlet temperature, feed flow rate, and boundary
layer heat transfer coefficient. Since lowering the temperature
polarization coefficient is essential enhance the process performance
considerable and maximizing the heat transfer coefficient for
maximizes the mass flux of distillate water. In this paper, the results
of VMD experiments are used to measure the boundary layer heat
transfer coefficient, and the experimental results are used to reevaluate
the empirical constants in the Dittus- Boelter equation.
Abstract: The value of overall oxygen transfer Coefficient
(KLa), which is the best measure of oxygen transfer in water through
aeration, is obtained by a simple approach, which sufficiently
explains the utility of the method to eliminate the discrepancies due
to inaccurate assumption of saturation dissolved oxygen
concentration. The rate of oxygen transfer depends on number of
factors like intensity of turbulence, which in turns depends on the
speed of rotation, size, and number of blades, diameter and
immersion depth of the rotor, and size and shape of aeration tank, as
well as on physical, chemical, and biological characteristic of water.
An attempt is made in this paper to correlate the overall oxygen
transfer Coefficient (KLa), as an independent parameter with other
influencing parameters mentioned above. It has been estimated that
the simulation equation developed predicts the values of KLa and
power with an average standard error of estimation of 0.0164 and
7.66 respectively and with R2 values of 0.979 and 0.989 respectively,
when compared with experimentally determined values. The
comparison of this model is done with the model generated using
Computational fluid dynamics (CFD) and both the models were
found to be in good agreement with each other.
Abstract: In Grid computing, a data transfer protocol called
GridFTP has been widely used for efficiently transferring a large volume
of data. Currently, two versions of GridFTP protocols, GridFTP
version 1 (GridFTP v1) and GridFTP version 2 (GridFTP v2), have
been proposed in the GGF. GridFTP v2 supports several advanced
features such as data streaming, dynamic resource allocation, and
checksum transfer, by defining a transfer mode called X-block mode.
However, in the literature, effectiveness of GridFTP v2 has not been
fully investigated. In this paper, we therefore quantitatively evaluate
performance of GridFTP v1 and GridFTP v2 using mathematical
analysis and simulation experiments. We reveal the performance
limitation of GridFTP v1, and quantitatively show effectiveness of
GridFTP v2. Through several numerical examples, we show that by
utilizing the data streaming feature, the average file transfer time of
GridFTP v2 is significantly smaller than that of GridFTP v1.
Abstract: In this paper, we present the design and experimental
evaluation of complementary energy path adiabatic logic (CEPAL)
based 1 bit full adder circuit. A simulative investigation on the
proposed full adder has been done using VIRTUOSO SPECTRE
simulator of cadence in 0.18μm UMC technology and its
performance has been compared with the conventional CMOS full
adder circuit. The CEPAL based full adder circuit exhibits the energy
saving of 70% to the conventional CMOS full adder circuit, at 100
MHz frequency and 1.8V operating voltage.
Abstract: The Beshar River is one aquatic ecosystem, which is
located next to the city of Yasuj in southern Iran. The Beshar river
has been contaminated by industrial factories such as effluent of
sugar factory, agricultural and other activities in this region such as,
Imam Sajjad hospital, drainage from agricultural farms, Yasuj urban
surface runoff and effluent of wastewater treatment plants ,specially
Yasuj waste water treatment plant. In order to evaluate the effects of
these pollutants on the quality of the Beshar river, five monitoring
stations were selected along its course. The first station is located
upstream of Yasuj near the Dehnow village; stations 2 to 4 are
located east, south and west of city; and the 5th station is located
downstream of Yasuj. Several water quality parameters were
sampled. These include pH, dissolved oxygen, biological oxygen
demand (BOD), temperature, conductivity, turbidity, total dissolved
solids and discharge or flow measurements. Water samples from the
five stations were collected and analyzed to determine the following
physicochemical parameters: EC, pH, T.D.S, T.H, No2, DO, BOD5,
COD during 2008 to 2010. The study shows that the BOD5 value of
station 1 is at a minimum (1.7 ppm) and increases downstream from
stations 2 to 4 to a maximum (11.6 ppm), and then decreases at
station 5. The DO values of station 1 is a maximum (8.45 ppm),
decreases downstream to stations 2 - 4 which are at a minimum (3.1
ppm), before increasing at station 5. The amount of BOD and TDS
are highest at the 4th station and the amount of DO is lowest at this
station, marking the 4th station as more highly polluted than the
other stations .This study shows average amount of the water quality
parameters in first year of sampling (2008) have had a better quality
relation to third year in 2010 because of recent drought in this region
and pollutant increasing .As the Beshar river path after 5th station
goes through the mountain area with more slope and flow velocity
,so the physicochemical parameters improve at the 5th station due to
pollutant degradation and dilution. Finally the point and nonpoint
pollutant sources of Beshar river were determined and compared to
the monitoring results.
Abstract: We evaluated the effect of sensory (direct current
(DC), 600μA) and motor (monophasic current, pulse duration 300μs,
100 Hz, 2.5-3mA) intensities of cathodal electrical stimulation (ES)
current to release VEGF and biomechanical properties of wound. 54
male Sprague-dawley rats were randomly assigned into one control
and two experimental groups. A full thickness skin incision was
made on animals- dorsal region. The experimental groups received
ES for 1h/day and every other day. VEGF expression was measured
in skin on the 7th day after surgical incision and tensile strength was
measured on 21st day. On the 7th day, the values of skin VEGF in the
sensory group were significantly greater than those of the other
groups (p < 0.05). Sensory and Motor intensity stimulation, can not
improve the biomechanical properties of the repaired wounds.
It seems the mechanical environment induced by sensory and
motor intensity of electrical stimulation, could not simulate the role
of normal daily stress and strain to maturation of collagen fibers and
their cross links. Further work is needed to determine the relationship
between VEGF expression after ES and its effect on tensile strength
of healed wound.
Abstract: This paper investigates the application of large scale (LS-PV) two-axis tracking photovoltaic power plant in Al-Jagbob, Libya. A 50MW PV-grid connected (two-axis tracking) power plant design in Al-Jagbob, Libya has been carried out presently. A hetero-junction with intrinsic thin layer (HIT) type PV module has been selected and modeled. A Microsoft Excel-VBA program has been constructed to compute slope radiation, dew-point, sky temperature, and then cell temperature, maximum power output and module efficiency for this system, for tracking system. The results for energy production show that the total energy output is 128.5 GWh/year. The average module efficiency is 16.6%. The electricity generation capacity factor (CF) and solar capacity factor (SCF) were found to be 29.3% and 70.4% respectively. A 50MW two axis tracking power plant with a total energy output of 128.5 GWh/year would reduce CO2 pollution by 85,581 tonnes of each year. The payback time for the proposed LS-PV photovoltaic power plant was found to be 4 years.
Abstract: The charge-exchange xenon (CEX) ion generated by ion thruster can backflow to the surface of spacecraft and threaten to the safety of spacecraft operation. In order to evaluate the effects of the induced plasma environment in backflow regions on the spacecraft, we designed a spherical single Langmuir probe of 5.8cm in diameter for measuring low-density plasma parameters in backflow region of ion thruster. In practice, the tests are performed in a two-dimensional array (40cm×60cm) composed of 20 sites. The experiment results illustrate that the electron temperature ranges from 3.71eV to 3.96eV, with the mean value of 3.82eV and the standard deviation of 0.064eV. The electron density ranges from 8.30×1012/m3 to 1.66×1013/m3, with the mean value of 1.30×1013/m3 and the standard deviation of 2.15×1012/m3. All data is analyzed according to the “ideal" plasma conditions of Maxwellian distributions.
Abstract: Some physico-chemical characteristics and mineral
composition of 'Karayemis' (Prunus laurocerasus L.) fruits which
grown naturally in Norteast Turkey was studied. 28 minerals ( Al,
Mg, B, Mn, Co, Na, Ca, Ni, Cd, P, Cr, Pb, Cu, S, Fe, Zn, K, Sr, Li,
As, V, Ag, Ba, Br, Ga, In, Se, Ti) were analyzed and 19 minerals
were present at ascertainable levels. Karayemis fruit was richest in
potassium (7938.711 ppm), magnesium (1242.186 ppm) and calcium
(1158.853 ppm). And some physico-chemical characteristics of
Karayemis fruit was investigated. Fruit length, fruit width, fruit
thickness, fruit weight, total soluble solids, colour, protein, crude ash,
crude fiber, crude oil values were determined as 2.334 cm, 1.884 cm,
2.112 cm, 5.35 g, 20.1 %, S99M99Y99, 0.29 %, 0.22 %, 6.63 % and
0.001 %, respectively. The seed of fruit mean weight, length, width
and thickness were found to be 0.41 g, 1.303 cm, 0.921 cm and
0.803, respectively.
Abstract: Creating shared value (CSV) is a newly introduced
concept whose essence and expressions, relationship to Corporate
social responsibility (CSR) and implications for the business and
society is now at the core of management and social responsibility
debates of the scientific world. The aim of the paper is to gain clearer
understanding of the CSR and CSV concepts, their implementation
and role in sustainable development of organizations in Latvia. In this
paper the authors discuss and compare the two conceptsand, based on
the results of Sustainability Index (SI) initiative and analysis of
publically available company information, evaluate their
implementation in Latvia and draw conclusions on the development
trends and potential of these approaches in Latvian market.
Abstract: There have been widespread applications of fluidized beds in industries which are related to the combination of gas-solid particles during the last decade. For instance, in order to crack the catalyses in petrochemical industries or as a drier in food industries. High capacity of fluidized bed in heat and mass transfer has made this device very popular. In order to achieve a higher efficiency of fluidized beds, a particular attention has been paid to beds with pulsating air flow. In this paper, a fluidized bed device with pulsating flow has been designed and constructed. Size of particles have been used during the test are in the range of 40 to 100μm. The purpose of this experimental test is to investigate the air flow regime, observe the particles- movement and measure the pressure loss along the bed. The effects of pulsation can be evaluated by comparing the results for both continuous and pulsating flow. Results of both situations are compared for various gas speeds. Moreover the above experiment is numerically simulated by using Fluent software and its numerical results are compared with the experimental results.
Abstract: This paper presents a novel approach for tuning unified power flow controller (UPFC) based damping controller in order to enhance the damping of power system low frequency oscillations. The design problem of damping controller is formulated as an optimization problem according to the eigenvalue-based objective function which is solved using iteration particle swarm optimization (IPSO). The effectiveness of the proposed controller is demonstrated through eigenvalue analysis and nonlinear time-domain simulation studies under a wide range of loading conditions. The simulation study shows that the designed controller by IPSO performs better than CPSO in finding the solution. Moreover, the system performance analysis under different operating conditions show that the δE based controller is superior to the mB based controller.
Abstract: The lifelong learning is a crucial element in the
modernization of European education and training systems. The most
important actors in the development process of the lifelong learning
are the trainers, whose professional characteristics need new
competences and skills in the current labour market. The main
objective of this paper is to establish an importance ranking of the
new competences, capabilities and skills that the lifelong learning
Spanish trainers must possess nowadays. A wide study of secondary
sources has allowed the design of a questionnaire that organizes the
trainer-s skills and competences. The e-Delphi method is used for
realizing a creative, individual and anonymous evaluation by experts
on the importance ranking that presents the criteria, sub-criteria and
indicators of the e-Delphi questionnaire. Twenty Spanish experts in
the lifelong learning have participated in two rounds of the e-
DELPHI method. In the first round, the analysis of the experts-
evaluation has allowed to establish the ranking of the most
importance criteria, sub-criteria and indicators and to eliminate the
least valued. The minimum level necessary to reach the consensus
among experts has been achieved in the second round.
Abstract: Recently electric vehicles are becoming popular as an
alternative of conventional fossil fuel vehicles. Conventional Internal
Combustion Engine (ICE) vehicle uses fossil fuel which contributing
a major part of overall carbon emission in the environment. Carbon
and other green house gas emission are responsible for global
warming and resulting climate change. It becomes vital to evaluate
performance of vehicle based on emission. In this paper an effort has
been made to depict the picture of emission caused by vehicle and
scenario of Australia has taken into account. Effort has been made to
compare the fossil based vehicle with electric vehicle in phases. The
study also evaluates advancement in electric vehicle technology,
required infrastructure for sustainability and future scope of
developments. This paper also includes the evaluation of electric
vehicle concept for pollution control and sustainable transport
systems in future. This study can be a benchmark for development of
electric vehicle as low carbon emission alternative for the cities of
tomorrow.
Abstract: The right to housing is a basic need while good
quality and affordable housing is a reflection of a high quality of life.
However, housing remains a major problem for most, especially for
the bottom billions. Satisfaction on housing and neighbourhood
conditions are one of the important indicators that reflect quality of
life. These indicators are also important in the process of evaluating
housing policy with the objective to increase the quality of housing
and neighbourhood. The research method is purely based on a
quantitative method, using a survey. The findings show that housing
purchasing trend in urban Malaysia is determined by demographic
profiles, mainly by education level, age, gender and income. The
period of housing ownership also influenced the socio-cultural
interactions and satisfaction of house owners with their
neighbourhoods. The findings also show that the main concerns for
house buyers in urban areas are price and location of the house.
Respondents feel that houses in urban Malaysia is too expensive and
beyond their affordability. Location of houses and distance from
work place are also regarded as the main concern. However,
respondents are fairly satisfied with religious and socio-cultural
facilities in the housing areas and most importantly not many regard
ethnicity as an issue in their decision-making, when buying a house.
Abstract: Fluids are used for heat transfer in many engineering
equipments. Water, ethylene glycol and propylene glycol are some
of the common heat transfer fluids. Over the years, in an attempt to
reduce the size of the equipment and/or efficiency of the process,
various techniques have been employed to improve the heat transfer
rate of these fluids. Surface modification, use of inserts and
increased fluid velocity are some examples of heat transfer
enhancement techniques. Addition of milli or micro sized particles
to the heat transfer fluid is another way of improving heat transfer
rate. Though this looks simple, this method has practical problems
such as high pressure loss, clogging and erosion of the material of
construction. These problems can be overcome by using nanofluids,
which is a dispersion of nanosized particles in a base fluid.
Nanoparticles increase the thermal conductivity of the base fluid
manifold which in turn increases the heat transfer rate. In this work,
the heat transfer enhancement using aluminium oxide nanofluid has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach.
Abstract: Topical photodynamic therapy (PDT) with
5-aminolevulinic acid (ALA) is an alternative therapy for treating
superficial cancer, especially for skin or oral cancer. ALA, a precursor
of the photosensitizer protoporphyrin IX (PpIX), is present as
zwitterions and hydrophilic property which make the low permeability
through the cell membrane. Collagen is a traditional carrier; its
molecular composed various amino acids which bear positive charge
and negative charge. In order to utilize the ion-pairs with ALA and
collagen, the study employed various pH values adjusting the net
charge. The aim of this study was to compare a series collagen form,
including solution, gel and sponge to investigate the topical delivery
behavior of ALA. The in vivo confocal laser scanning microscopy
(CLSM) study demonstrated that PpIX generation ability was different
pattern after apply for 6 h. Gel type could generate high PpIX, and
archived more deep of skin depth.
Abstract: This paper deals with the tuning of parameters for Automatic Generation Control (AGC). A two area interconnected hydrothermal system with PI controller is considered. Genetic Algorithm (GA) and Particle Swarm optimization (PSO) algorithms have been applied to optimize the controller parameters. Two objective functions namely Integral Square Error (ISE) and Integral of Time-multiplied Absolute value of the Error (ITAE) are considered for optimization. The effectiveness of an objective function is considered based on the variation in tie line power and change in frequency in both the areas. MATLAB/SIMULINK was used as a simulation tool. Simulation results reveal that ITAE is a better objective function than ISE. Performances of optimization algorithms are also compared and it was found that genetic algorithm gives better results than particle swarm optimization algorithm for the problems of AGC.