Abstract: Addition of milli or micro sized particles to the heat
transfer fluid is one of the many techniques employed for improving
heat transfer rate. Though this looks simple, this method has
practical problems such as high pressure loss, clogging and erosion
of the material of construction. These problems can be overcome by
using nanofluids, which is a dispersion of nanosized particles in a
base fluid. Nanoparticles increase the thermal conductivity of the
base fluid manifold which in turn increases the heat transfer rate.
Nanoparticles also increase the viscosity of the basefluid resulting in
higher pressure drop for the nanofluid compared to the base fluid. So
it is imperative that the Reynolds number (Re) and the volume
fraction have to be optimum for better thermal hydraulic
effectiveness. In this work, the heat transfer enhancement using
aluminium oxide nanofluid using low and high volume fraction
nanofluids in turbulent pipe flow with constant wall temperature has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach. Nanofluid, up till
a volume fraction of 1% is found to be an effective heat transfer
enhancement technique. The Nusselt number (Nu) and friction factor
predictions for the low volume fractions (i.e. 0.02%, 0.1 and 0.5%)
agree very well with the experimental values of Sundar and Sharma
(2010). While, predictions for the high volume fraction nanofluids
(i.e. 1%, 4% and 6%) are found to have reasonable agreement with
both experimental and numerical results available in the literature.
So the computationally inexpensive single phase approach can be
used for heat transfer and pressure drop prediction of new nanofluids.
Abstract: Prickly pear juice has received renewed attention with regard to the effects of processing and preservation on its sensory qualities (colour, taste, flavour, aroma, astringency, visual browning and overall acceptability). Juice was prepared by homogenizing fruit and treating the pulp with pectinase (Aspergillus niger). Juice treatments applied were sugar addition, acidification, heat-treatment, refrigeration, and freezing and thawing. Prickly pear pulp and juice had unique properties (low pH 3.88, soluble solids 3.68 oBrix and high titratable acidity 0.47). Sensory profiling and descriptive analyses revealed that non-treated juice had a bitter taste with high astringency whereas treated prickly pear was significantly sweeter. All treated juices had a good sensory acceptance with values approximating or exceeding 7. Regression analysis of the consumer sensory attributes for non-treated prickly pear juice indicated an overwhelming rejection, while treated prickly pear juice received overall acceptability. Thus, educed favourable sensory responses and may have positive implications for consumer acceptability.
Abstract: Towards the end of 19th century, the discovery of tin
and the growing importance of rubber, had led Malaya to once again
become the centre of attraction to western colonization, which later
on caused the region to be influxed by cheap labour from China and
India. One of the factors which attracted the alien communities was
the characteristics of social relation offered by the Malays. If one
analyzes the history of social relation of the Malays either among
themselves or their relation with alien communities, it is apparent that
the community places high regards to values such as tolerant,
cooperative, respectful and helpful with each other. In fact, all these
values are deeply rooted in the value of 'budi'. With the arrival of
Islam, the value of 'budi' had been well assimilated with Islamic
values thus giving birth to the value of 'budi-Islam'. Through 'budi-
Islam', the Malay conducted their dealings with British as well the
other communities during the time of peace or conflict. This value is
well nurtured due to the geographical circumstances like the fertile,
naturally rich land and bountiful marine life. Besides, a set of Malay
customs known as 'adat' custom contributed in enhancing the values
of budi.
Abstract: Intellectual capital measurement is a central aspect of knowledge management. The measurement and the evaluation of intangible assets play a key role in allowing an effective management of these assets as sources of competitiveness. For these reasons, managers and practitioners need conceptual and analytical tools taking into account the unique characteristics and economic significance of Intellectual Capital. Following this lead, we propose an efficiency and productivity analysis of Intellectual Capital, as a determinant factor of the company competitive advantage. The analysis is carried out by means of Data Envelopment Analysis (DEA) and Malmquist Productivity Index (MPI). These techniques identify Bests Practice companies that have accomplished competitive advantage implementing successful strategies of Intellectual Capital management, and offer to inefficient companies development paths by means of benchmarking. The proposed methodology is employed on the Biotechnology industry in the period 2007-2010.
Abstract: The study aimed to evaluated the reproductive performance response to short term oestrus synchronization during the transition period. One hundred and sixty-five indigenous multiparous non-lactating goats were subdivided into the following six treatment groups for oestrus synchronization: NT control Group (N= 30), Fe-21d, FGA vaginal sponge for 21days+eCG at 19thd; FPe- 11d, FGA 11d + PGF2α and eCG at 9th d; FPe-10d, FGA 10d+ PGF2α and eCG at 8th d; FPe-9d, FGA 9d +PGF2α and eCG at 7thd; PFe-5d, PGF2α at d0 + FGA 5d + eCG at 5thd. The goats were natural mated (1 male/6 females). Fecundity rates (n. births /n. females treated x 100) were statistically higher (P < 0.05) in short term FPe-9d (157.9%), FPe- 11d (115.4%), FPe-10d (111.1%) and PFe-5d (107.7%) groups compared to the NT control Group (66.7%).
Abstract: The primary purpose of this article is an attempt to
find the implication of globalization on education. Globalization has
an important role as a process in the economical, political, cultural
and technological dimensions in the life of the contemporary human
being and has been affected by it. Education has its effects in this
procedure and while influencing it through educating global citizens
having universal human features and characteristics, has been
influenced by this phenomenon too. Nowadays, the role of education
is not just to develop in the students the knowledge and skills
necessary for the new kinds of jobs. If education wants to help
students be prepared of the new global society, it has to make them
engaged productive and critical citizens for the global era, so that
they can reflect about their roles as key actors in a dynamic often
uneven, matrix of economic and cultural exchanges. If education
wants to reinforce and raise the national identity, the value system
and the children and teenagers, it should make them ready for living
in the global era of this century. The used method in this research is
documentary and analyzing the documents. Studies in this field show
globalization has influences on the processes of the production,
distribution and consuming of knowledge. The happening of this
event in the information era has not only provide the necessary
opportunities for the exchanges of education worldwide but also has
privileges for the developing countries which enables them to
strengthen educational bases of their society and have an important
step toward their future.
Abstract: The present work encounters the solution of the defect identification problem with the use of an evolutionary algorithm combined with a simplex method. In more details, a Matlab implementation of Genetic Algorithms is combined with a Simplex method in order to lead to the successful identification of the defect. The influence of the location and the orientation of the depressed ellipsoidal flaw was investigated as well as the use of different amount of static data in the cost function. The results were evaluated according to the ability of the simplex method to locate the global optimum in each test case. In this way, a clear impression regarding the performance of the novel combination of the optimization algorithms, and the influence of the geometrical parameters of the flaw in defect identification problems was obtained.
Abstract: This paper presents a hand vein authentication system
using fast spatial correlation of hand vein patterns. In order to
evaluate the system performance, a prototype was designed and a
dataset of 50 persons of different ages above 16 and of different
gender, each has 10 images per person was acquired at different
intervals, 5 images for left hand and 5 images for right hand. In
verification testing analysis, we used 3 images to represent the
templates and 2 images for testing. Each of the 2 images is matched
with the existing 3 templates. FAR of 0.02% and FRR of 3.00 %
were reported at threshold 80. The system efficiency at this threshold
was found to be 99.95%. The system can operate at a 97% genuine
acceptance rate and 99.98 % genuine reject rate, at corresponding
threshold of 80. The EER was reported as 0.25 % at threshold 77. We
verified that no similarity exists between right and left hand vein
patterns for the same person over the acquired dataset sample.
Finally, this distinct 100 hand vein patterns dataset sample can be
accessed by researchers and students upon request for testing other
methods of hand veins matching.
Abstract: This study aimed to present the mechanical
performance evaluation of the dynamic hip screw (DHS) for
trochanteric fracture by means of finite element method. The
analyses were performed based on stainless steel and titanium
implant material definitions at various stages of bone healing and
including implant removal. The assessment of the mechanical
performance used two parameters, von Mises stress to evaluate the
strength of bone and implant and elastic strain to evaluate fracture
stability. The results show several critical aspects of dynamic hip
screw for trochanteric fracture stabilization. In the initial stage of
bone healing process, partial weight bearing should be applied to
avoid the implant failure. In the late stage of bone healing, stainless
steel implant should be removed.
Abstract: The distribution, enrichment, accumulation, and potential ecological risk of copper (Cu) in the surface sediments of northern Kaohsiung Harbor, Taiwan were investigated. Sediment samples from 12 locations of northern Kaohsiung Harbor were collected and characterized for Cu, aluminum, water content, organic matter, total nitrogen, total phosphorous, total grease and grain size. Results showed that the Cu concentrations varied from 6.9–244 mg/kg with an average of 109±66 mg/kg. The spatial distribution of Cu reveals that the Cu concentration is relatively high in the river mouth region, and gradually diminishes toward the harbor entrance region. This indicates that upstream industrial and municipal wastewater discharges along the river bank are major sources of Cu pollution. Results from the enrichment factor and geo-accumulation index analyses imply that the sediments collected from the river mouth can be characterized between moderate and moderately severe degree enrichment and between none to medium and moderate accumulation of Cu, respectively. However, results of potential ecological risk index indicate that the sediment has low ecological potential risk.
Abstract: A hybrid Photovoltaic/Thermal (PV/T) solar system integrates photovoltaic and solar thermal technologies into one single solar energy device, with dual generation of electricity and heat energy. The aim of the present study is to evaluate the potential for introduction of the PV/T technology into Northern China. For this purpose, outdoor experiments were conducted on a prototype of a PV/T water-heating system. The annual thermal and electrical performances were investigated under the climatic conditions of Beijing. An economic analysis of the system was then carried out, followed by a sensitivity study. The analysis revealed that the hybrid system is not economically attractive with the current market and energy prices. However, considering the continuous commitment of the Chinese government towards policy development in the renewable energy sector, and technological improvements like the increasing cost-effectiveness of PV cells, PV/Thermal technology may become economically viable in the near future.
Abstract: In an Orthogonal Frequency Division Multiplexing (OFDM) systems, the Peak to Average power Ratio (PAR) is high. The clipping signal scheme is a useful and simple method to reduce the PAR. However, it introduces additional noise that degrades the systems performance. We propose an oversampling scheme to deal with the received signal in order to reduce the clipping noise by using Finite Impulse Response (FIR) filter. Coefficients of filter are obtained by correlation function of the received signal and the oversampling information at receiver. The performance of the proposed technique is evaluated for frequency selective channel. Results show that the proposed scheme can mitigate the clipping noise significantly for OFDM systems and in order to maintain the system's capacity, the clipping ratio should be larger than 2.5.
Abstract: Truss optimization problem has been vastly studied
during the past 30 years and many different methods have been
proposed for this problem. Even though most of these methods
assume that the design variables are continuously valued, in reality,
the design variables of optimization problems such as cross-sectional
areas are discretely valued. In this paper, an improved hill climbing
and an improved simulated annealing algorithm have been proposed
to solve the truss optimization problem with discrete values for crosssectional
areas. Obtained results have been compared to other
methods in the literature and the comparison represents that the
proposed methods can be used more efficiently than other proposed
methods
Abstract: This paper aims to explain the project carried out at
the University of Cordoba, specifically at the High Polytechnic
School in collaboration with two other organizations belonging to the
Andalusian Ministry of Innovation, Science and Business:
Andalusian Innovation and Development Agency (IDEA agency) [1]
and the Territorial Net of Entrepreneurship Support (in Spanish Red
Territorial de Apoyo al Emprendedor) [11].
The project is being developed in several stages of which only the
first one has already been completed. However, several important
preliminary results derive from it, based mainly in the description of
the nature of entrepreneurship in the field of university education and
its impact on student-s competency as recommended by the European
Higher Education Area. Some problems holding back the correct
future development will also be shown as derived from the specific
context of application of the project.
Abstract: The aim of present experiment was to evaluate the
influence of cultivar to quality parameters of dried potato chips and
sticks produced in microwave-vacuum drier. The potatoes before
drying were blanched in oil and water at 180ºC and at 85ºC
respectively. The moisture content, crispiness, the colour (CIE
L*a*b*), the content of ascorbic acid, total carotenoids and total fat
content of dried potato chips and sticks was determined The highest
ascorbic acid content, high content of carotenoids, low total fat
content, low acrylamide content and good crispiness (low breaking
force) especially for sticks was determined in the samples of Gundega
cultivar.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: The aim of this study is evaluating the antinociceptive
and anti-inflamatory activity of Geum kokanicum. After
determination total extract LD50, different doses of extract were
chosen for intrapritoneal injections. In inflammation test, male NMRI
mice were divided into 6 groups: control (normal saline), positive
control (Dexamethasone 15mg/kg), and total extract (0.025, 0.05,
0.1, and 0.2 gr/kg). The inflammation was produced by xyleneinduced
edema. In order to evaluate the antinociceptive effect of total
extract, formalin test was used. Mice were divided into 6 groups:
control, positive control (morphine 10mg/kg), and 4 groups which
received total extract. Then they received Formalin. The animals
were observed for the reaction to pain. Data were analyzed using
One-way ANOVA followed by Tukey-Kramer multiple comparison
test. LD50 was 1 gr/kg. Data indicated that 0.5,0.1 and 0.2 gr/kg
doses of total extract have particular antinociceptive and antiinflammatory
effects in a comparison with control (P
Abstract: Magnesium is used implant material potentially for
non-toxicity to the human body. Due to the excellent
bio-compatibility, Mg alloys is applied to implants avoiding removal
second surgery. However, it is found commercial magnesium alloys
including aluminum has low corrosion resistance, resulting
subcutaneous gas bubbles and consequently the approach as
permanent bio-materials. Generally, Aluminum is known to pollution
substance, and it raises toxicity to nervous system. Therefore
especially Mg-35Zn-3Ca alloy is prepared for new biodegradable
materials in this study. And the pulsed power is used in
constant-current mode of DC power kinds of anodization. Based on
the aforementioned study, it examines corrosion resistance and
biocompatibility by effect of current and frequency variation. The
surface properties and thickness were compared using scanning
electronic microscopy. Corrosion resistance was assessed via
potentiodynamic polarization and the effect of oxide layer on the body
was assessed cell viability. Anodized Mg-35Zn-3Ca alloy has good
biocompatibility in vitro by current and frequency variation.
Abstract: The influence of axial magnetic field (B=0.48 T) on
the variation of ionization efficiency coefficient h and secondary
electron emission coefficient g with respect to reduced electric field
E/P is studied at a new range of plane-parallel electrode spacing (0<
d< 20 cm) and different nitrogen working pressure between 0.5-20
Pa. The axial magnetic field is produced from an inductive copper
coil of radius 5.6 cm. The experimental data of breakdown voltage is
adopted to estimate the mean Paschen curves at different working
features. The secondary electron emission coefficient is calculated
from the mean Paschen curve and used to determine the minimum
breakdown voltage. A reduction of discharge voltage of about 25% is
investigated by the applied of axial magnetic field. At high interelectrode
spacing, the effect of axial magnetic field becomes more
significant for the obtained values of h but it was less for the values
of g.
Abstract: This paper presents an interval-based multi-attribute
decision making (MADM) approach in support of the decision
process with imprecise information. The proposed decision
methodology is based on the model of linear additive utility function
but extends the problem formulation with the measure of composite
utility variance. A sample study concerning with the evaluation of
electric generation expansion strategies is provided showing how the
imprecise data may affect the choice toward the best solution and
how a set of alternatives, acceptable to the decision maker (DM),
may be identified with certain confidence.