Abstract: This paper describes the speed sensorless vector control method of the parallel connected induction motor drive fed by a single inverter. Speed and rotor fluxes of the induction motor are estimated by natural observer with load torque adaptation and adaptive rotor flux observer. The performance parameters speed and rotor fluxes are estimated from the measured terminal voltages and currents. Fourth order induction motor model is used and speed is considered as a parameter. The performance of the natural observer is similar to the conventional observer. The speed of an induction motor is estimated by MATLAB simulation under different speed and load conditions. Estimated values along with other measured states are used for closed loop control. The simulation results show that the natural observer is also effective for parallel connected induction motor drive.
Abstract: In order to develop forest management strategies in
tropical forest in Malaysia, surveying the forest resources and
monitoring the forest area affected by logging activities is essential.
There are tremendous effort has been done in classification of land
cover related to forest resource management in this country as it is a
priority in all aspects of forest mapping using remote sensing and
related technology such as GIS. In fact classification process is a
compulsory step in any remote sensing research. Therefore, the main
objective of this paper is to assess classification accuracy of
classified forest map on Landsat TM data from difference number of
reference data (200 and 388 reference data). This comparison was
made through observation (200 reference data), and interpretation
and observation approaches (388 reference data). Five land cover
classes namely primary forest, logged over forest, water bodies, bare
land and agricultural crop/mixed horticultural can be identified by
the differences in spectral wavelength. Result showed that an overall
accuracy from 200 reference data was 83.5 % (kappa value
0.7502459; kappa variance 0.002871), which was considered
acceptable or good for optical data. However, when 200 reference
data was increased to 388 in the confusion matrix, the accuracy
slightly improved from 83.5% to 89.17%, with Kappa statistic
increased from 0.7502459 to 0.8026135, respectively. The accuracy
in this classification suggested that this strategy for the selection of
training area, interpretation approaches and number of reference data
used were importance to perform better classification result.
Abstract: To decompose organochlorides by bioremediation, co-culture biohydrogen producer and dehalogenation microorganisms is a useful method. In this study, we combined these two characteristics from a biohydrogen producer, Rhodopseudomonas palustris, and a dehalogenation microorganism, Pseudomonas putida, to enchance halorespiration in R. palustris. The genes encoding cytochrome P450cam system (camC, camA, and camB) from P. putida were expressed in R. palustris with designated expression plasmid. All tested strains were cultured to log phase then presented pentachloroethane (PCA) in media. The vector control strain could degrade PCA about 78% after 16 hours, however, the cytochrome P450cam system expressed strain, CGA-camCAB, could completely degrade PCA in 12 hours. While taking chlorinated aromatic, 3-chlorobenzoate, as sole carbon source or present benzoate as co-substrate, CGA-camCAB presented faster growth rate than vector control strain.
Abstract: Flow movement in unsaturated soil can be expressed
by a partial differential equation, named Richards equation. The
objective of this study is the finding of an appropriate implicit
numerical solution for head based Richards equation. Some of the
well known finite difference schemes (fully implicit, Crank Nicolson
and Runge-Kutta) have been utilized in this study. In addition, the
effects of different approximations of moisture capacity function,
convergence criteria and time stepping methods were evaluated. Two
different infiltration problems were solved to investigate the
performance of different schemes. These problems include of vertical
water flow in a wet and very dry soils. The numerical solutions of
two problems were compared using four evaluation criteria and the
results of comparisons showed that fully implicit scheme is better
than the other schemes. In addition, utilizing of standard chord slope
method for approximation of moisture capacity function, automatic
time stepping method and difference between two successive
iterations as convergence criterion in the fully implicit scheme can
lead to better and more reliable results for simulation of fluid
movement in different unsaturated soils.
Abstract: The condition of lightning surge causes the traveling waves and the temporary increase in voltage in the transmission line system. Lightning is the most harmful for destroying the transmission line and setting devices so it is necessary to study and analyze the temporary increase in voltage for designing and setting the surge arrester. This analysis describes the figure of the lightning wave in transmission line with 115 kV voltage level in Thailand by using ATP/EMTP program to create the model of the transmission line and lightning surge. Because of the limit of this program, it must be calculated for the geometry of the transmission line and surge parameter and calculation in the manual book for the closest value of the parameter. On the other hand, for the effects on surge protector when the lightning comes, the surge arrester model must be right and standardized as metropolitan electrical authority's standard. The candidate compared the real information to the result from calculation, also. The results of the analysis show that the temporary increase in voltage value will be rise to 326.59 kV at the line which is done by lightning when the surge arrester is not set in the system. On the other hand, the temporary increase in voltage value will be 182.83 kV at the line which is done by lightning when the surge arrester is set in the system and the period of the traveling wave is reduced, also. The distance for setting the surge arrester must be as near to the transformer as possible. Moreover, it is necessary to know the right distance for setting the surge arrester and the size of the surge arrester for preventing the temporary increase in voltage, effectively.
Abstract: Metallic micro parts are playing an important role in micro-fabrication industry. Recently, we have demonstrated a new deformation mechanism for micro-formability of polycrystalline materials. Different depressed micro-features smaller than the grain size have been successfully fabricated on 6061 aluminum alloy (AA6061) substrates with good fidelity. To further verify this proposed deformation mechanism that grain size is not a limiting factor, we demonstrate here that in addition of depressed features, protruded micro-features on a polycrystalline substrate can similarly be fabricated.
Abstract: The unanticipated brittle fracture of connection of the
steel moment resisting frame (SMRF) occurred in 1994 the Northridge
earthquake. Since then, the researches for the vulnerability of
connection of the existing SMRF and for rehabilitation of those
buildings were conducted. This paper suggests performance-based
optimal seismic retrofit technique using connection upgrade. For
optimal design, a multi-objective genetic algorithm(NSGA-II) is used.
One of the two objective functions is to minimize initial cost and
another objective function is to minimize lifetime seismic damages
cost. The optimal algorithm proposed in this paper is performed
satisfying specified performance objective based on FEMA 356. The
nonlinear static analysis is performed for structural seismic
performance evaluation. A numerical example of SAC benchmark
SMRF is provided using the performance-based optimal seismic
retrofit technique proposed in this paper
Abstract: In this paper we improve the quasilinearization method by barycentric Lagrange interpolation because of its numerical stability and computation speed to achieve a stable semi analytical solution. Then we applied the improved method for solving the Fin problem which is a nonlinear equation that occurs in the heat transferring. In the quasilinearization approach the nonlinear differential equation is treated by approximating the nonlinear terms by a sequence of linear expressions. The modified QLM is iterative but not perturbative and gives stable semi analytical solutions to nonlinear problems without depending on the existence of a smallness parameter. Comparison with some numerical solutions shows that the present solution is applicable.
Abstract: This research proposes a Preemptive Possibilistic
Linear Programming (PPLP) approach for solving multiobjective
Aggregate Production Planning (APP) problem with interval demand
and imprecise unit price and related operating costs. The proposed
approach attempts to maximize profit and minimize changes of
workforce. It transforms the total profit objective that has imprecise
information to three crisp objective functions, which are maximizing
the most possible value of profit, minimizing the risk of obtaining the
lower profit and maximizing the opportunity of obtaining the higher
profit. The change of workforce level objective is also converted.
Then, the problem is solved according to objective priorities. It is
easier than simultaneously solve the multiobjective problem as
performed in existing approach. Possible range of interval demand is
also used to increase flexibility of obtaining the better production
plan. A practical application of an electronic company is illustrated to
show the effectiveness of the proposed model.
Abstract: The purpose of this study is to find natural gait of
biped robot such as human being by analyzing the COG (Center Of
Gravity) trajectory of human being's gait. It is discovered that human
beings gait naturally maintain the stability and use the minimum
energy. This paper intends to find the natural gait pattern of biped
robot using the minimum energy as well as maintaining the stability by
analyzing the human's gait pattern that is measured from gait image on
the sagittal plane and COG trajectory on the frontal plane. It is not
possible to apply the torques of human's articulation to those of biped
robot's because they have different degrees of freedom. Nonetheless,
human and 5-link biped robots are similar in kinematics. For this, we
generate gait pattern of the 5-link biped robot by using the GA
algorithm of adaptation gait pattern which utilize the human's ZMP
(Zero Moment Point) and torque of all articulation that are measured
from human's gait pattern. The algorithm proposed creates biped
robot's fluent gait pattern as that of human being's and to minimize
energy consumption because the gait pattern of the 5-link biped robot
model is modeled after consideration about the torque of human's each
articulation on the sagittal plane and ZMP trajectory on the frontal
plane. This paper demonstrate that the algorithm proposed is superior
by evaluating 2 kinds of the 5-link biped robot applied to each gait
patterns generated both in the general way using inverse kinematics
and in the special way in which by considering visuality and
efficiency.
Abstract: A proof of convergence of a new continuation algorithm for computing the Analytic SVD for a large sparse parameter– dependent matrix is given. The algorithm itself was developed and numerically tested in [5].
Abstract: Failure modes and effects analysis (FMEA) is an effective technique for preventing potential problems and actions needed to error cause removal. On the other hand, the oil producing companies paly a critical role in the oil industry of Iran as a developing country out of which, Sepahan Oil Co. has a considerable contribution. The aim of this research is to show how FMEA could be applied and improve the quality of products at Sepahan Oil Co. For this purpose, the four liter production line of the company has been selected for investigation. The findings imply that the application of FMEA has reduced the scraps from 50000 ppm to 5000 ppm and has resulted in a 0.92 percent decrease of the oil waste.
Abstract: The present work presents a method of calculating the
ductility of rectangular sections of beams considering nonlinear
behavior of concrete and steel. This calculation procedure allows us
to trace the curvature of the section according to the bending
moment, and consequently deduce ductility. It also allowed us to
study the various parameters that affect the value of the ductility. A
comparison of the effect of maximum rates of tension steel, adopted
by the codes, ACI [1], EC8 [2] and RPA [3] on the value of the
ductility was made. It was concluded that the maximum rate of steels
permitted by the ACI [1] codes and RPA [3] are almost similar in
their effect on the ductility and too high. Therefore, the ductility
mobilized in case of an earthquake is low, the inverse of code EC8
[2]. Recommendations have been made in this direction.
Abstract: Bridges are one of the main components of
transportation networks. They should be functional before and after
earthquake for emergency services. Therefore we need to assess
seismic performance of bridges under different seismic loadings.
Fragility curve is one of the popular tools in seismic evaluations. The
fragility curves are conditional probability statements, which give the
probability of a bridge reaching or exceeding a particular damage
level for a given intensity level. In this study, the seismic
performance of a two-span simply supported concrete bridge is
assessed. Due to usual lack of empirical data, the analytical fragility
curve was developed by results of the dynamic analysis of bridge
subjected to the different time histories in near-fault area.
Abstract: This paper presents the design and implements the prototype of an intelligent data processing framework in ubiquitous sensor networks. Much focus is put on how to handle the sensor data stream as well as the interoperability between the low-level sensor data and application clients. Our framework first addresses systematic middleware which mitigates the interaction between the application layer and low-level sensors, for the sake of analyzing a great volume of sensor data by filtering and integrating to create value-added context information. Then, an agent-based architecture is proposed for real-time data distribution to efficiently forward a specific event to the appropriate application registered in the directory service via the open interface. The prototype implementation demonstrates that our framework can host a sophisticated application on the ubiquitous sensor network and it can autonomously evolve to new middleware, taking advantages of promising technologies such as software agents, XML, cloud computing, and the like.
Abstract: The present study based on removal of natural dyes of
Roselle petals, then used Roselle petals powder (RPP) as an
adsorbent for the removal of methylene blue dye (as a typical cationic
or basic dye) from aqueous solutions. The present study shows that
used Roselle petals powder exhibit adsorption trend for the dye. The
adsorption processes were carried out at various conditions of
temperatures ranging from 278 to 338 K ± 2 K , concentrations,
processing time and a wide range of pH between 2.5-11. Adsorption
isotherm equations such as Freundlich, and Langmuir were applied to
calculate the values of respective constants. Adsorption study was
found that the currently introduced adsorbent can be used to remove
cationic dyes such as methylene blue from aqueous solutions.
Abstract: In this paper, a reliable cooperative multipath routing
algorithm is proposed for data forwarding in wireless sensor networks
(WSNs). In this algorithm, data packets are forwarded towards the
base station (BS) through a number of paths, using a set of relay
nodes. In addition, the Rayleigh fading model is used to calculate
the evaluation metric of links. Here, the quality of reliability is
guaranteed by selecting optimal relay set with which the probability
of correct packet reception at the BS will exceed a predefined
threshold. Therefore, the proposed scheme ensures reliable packet
transmission to the BS. Furthermore, in the proposed algorithm,
energy efficiency is achieved by energy balancing (i.e. minimizing
the energy consumption of the bottleneck node of the routing path)
at the same time. This work also demonstrates that the proposed
algorithm outperforms existing algorithms in extending longevity of
the network, with respect to the quality of reliability. Given this, the
obtained results make possible reliable path selection with minimum
energy consumption in real time.
Abstract: Cognitive models allow predicting some aspects of utility
and usability of human machine interfaces (HMI), and simulating
the interaction with these interfaces. The action of predicting is based
on a task analysis, which investigates what a user is required to do
in terms of actions and cognitive processes to achieve a task. Task
analysis facilitates the understanding of the system-s functionalities.
Cognitive models are part of the analytical approaches, that do not
associate the users during the development process of the interface.
This article presents a study about the evaluation of a human
machine interaction with a contextual assistant-s interface using ACTR
and GOMS cognitive models. The present work shows how these
techniques may be applied in the evaluation of HMI, design and
research by emphasizing firstly the task analysis and secondly the
time execution of the task. In order to validate and support our
results, an experimental study of user performance is conducted at
the DOMUS laboratory, during the interaction with the contextual
assistant-s interface. The results of our models show that the GOMS
and ACT-R models give good and excellent predictions respectively
of users performance at the task level, as well as the object level.
Therefore, the simulated results are very close to the results obtained
in the experimental study.
Abstract: We provide a maximum norm analysis of a finite
element Schwarz alternating method for a nonlinear elliptic boundary
value problem of the form -Δu = f(u), on two overlapping sub
domains with non matching grids. We consider a domain which is
the union of two overlapping sub domains where each sub domain
has its own independently generated grid. The two meshes being
mutually independent on the overlap region, a triangle belonging to
one triangulation does not necessarily belong to the other one. Under
a Lipschitz assumption on the nonlinearity, we establish, on each sub
domain, an optimal L∞ error estimate between the discrete Schwarz
sequence and the exact solution of the boundary value problem.
Abstract: Neighborhood Rough Sets (NRS) has been proven to
be an efficient tool for heterogeneous attribute reduction. However,
most of researches are focused on dealing with complete and noiseless
data. Factually, most of the information systems are noisy, namely,
filled with incomplete data and inconsistent data. In this paper, we
introduce a generalized neighborhood rough sets model, called
VPTNRS, to deal with the problem of heterogeneous attribute
reduction in noisy system. We generalize classical NRS model with
tolerance neighborhood relation and the probabilistic theory.
Furthermore, we use the neighborhood dependency to evaluate the
significance of a subset of heterogeneous attributes and construct a
forward greedy algorithm for attribute reduction based on it.
Experimental results show that the model is efficient to deal with noisy
data.