Abstract: The present study investigates numerically the
phenomenon of vortex-shedding and its suppression in twodimensional
mixed convective flow past a square cylinder under the
joint influence of buoyancy and free-stream orientation with respect
to gravity. The numerical experiments have been conducted at a
fixed Reynolds number (Re) of 100 and Prandtl number (Pr) of 0.71,
while Richardson number (Ri) is varied from 0 to 1.6 and freestream
orientation, α, is kept in the range 0o≤ α ≤ 90o, with 0o
corresponding to an upward flow and 90o representing a cross-flow
scenario, respectively. The continuity, momentum and energy
equations, subject to Boussinesq approximation, are discretized using
a finite difference method and are solved by a semi-explicit pressure
correction scheme. The critical Richardson number, leading to the
suppression of the vortex-shedding (Ric), is estimated by using
Stuart-Landau theory at various free-stream orientations and the
neutral curve is obtained in the Ri-α plane. The neutral curve
exhibits an interesting non-monotonic behavior with Ric first
increasing with increasing values of α upto 45o and then decreasing
till 70o. Beyond 70o, the neutral curve again exhibits a sharp
increasing asymptotic trend with Ric approaching very large values
as α approaches 90o. The suppression of vortex shedding is not
observed at α = 90o (cross-flow). In the unsteady flow regime, the
Strouhal number (St) increases with the increase in Richardson
number.
Abstract: The intent of this essay is to evaluate the effectiveness
of surge suppressor aimed at power supply used for automation
devices in power distribution system which is consist of MOV and
T type low-pass filter. Books, journal articles and e-sources related
to surge protection of power supply used for automation devices in
power distribution system were consulted, and the useful information
was organized, analyzed and developed into five parts: characteristics
of surge wave, protection against surge wave, impedance characteristics
of target, using Matlab to simulate circuit response after
5kV,1.2/50s surge wave and suggestions for surge protection. The
results indicate that various types of load situation have great impact
on the effectiveness of surge protective device. Therefore, type and
parameters of surge protective device need to be carefully selected,
and load matching is also vital to be concerned.
Abstract: This paper presents the application of a signal
intensity independent registration criterion for 2D rigid body
registration of medical images using 1D binary projections. The
criterion is defined as the weighted ratio of two projections. The ratio
is computed on a pixel per pixel basis and weighting is performed by
setting the ratios between one and zero pixels to a standard high
value. The mean squared value of the weighted ratio is computed
over the union of the one areas of the two projections and it is
minimized using the Chebyshev polynomial approximation using
n=5 points. The sum of x and y projections is used for translational
adjustment and a 45deg projection for rotational adjustment. 20 T1-
T2 registration experiments were performed and gave mean errors
1.19deg and 1.78 pixels. The method is suitable for contour/surface
matching. Further research is necessary to determine the robustness
of the method with regards to threshold, shape and missing data.
Abstract: The purpose of this study is to investigate the
efficiency of a double-layer roof in collecting solar energy as an
application to the areas such as raising high-end temperature of
organic Rankine cycle (ORC). The by-product of the solar roof is to
reduce building air-conditioning loads. The experimental apparatus
are arranged to evaluate the effects of the solar roof in absorbing solar
energy. The flow channel is basically formed by an aluminum plate on
top of a plywood plate. The geometric configurations in which the
effects of absorbing energy is analyzed include: a bare uncovered
aluminum plate, a glass-covered aluminum plate, a
glass-covered/black-painted aluminum plate, a plate with variable
lengths, a flow channel with stuffed material (in an attempt on
enhancement of heat conduction), and a flow channel with variable
slanted angles. The experimental results show that the efficiency of
energy collection varies from 0.6 % to 11 % for the geometric
configurations mentioned above. An additional study is carried out
using CFD simulation to investigate the effects of fins on the
aluminum plate. It shows that due to vastly enhanced heat conduction,
the efficiency can reach ~23 % if 50 fins are installed on the aluminum
plate. The study shows that a double-layer roof can efficiently absorb
solar energy and substantially reduce building air-conditioning
loads. On the high end of an organic Rankine cycle, a solar pond is
used to replace the warm surface water of the sea as OTEC (ocean
thermal energy conversion) is the driving energy for the ORC. The
energy collected from the double-layered solar roof can be pumped
into the pond and raise the pond temperature as the pond surface area is
equivalently increased by nearly one-fourth of the total area of the
double-layer solar roof. The effect of raising solar pond temperature is
especially prominent if the double-layer solar roofs are installed in a
community area.
Abstract: In many cases, there are some time lag between the consumption of inputs and the production of outputs. This time lag effect should be considered in evaluating the performance of organizations. Recently, a couple of DEA models were developed for considering time lag effect in efficiency evaluation of research activities. Multi-periods input(MpI) and Multi-periods output(MpO) models are integrate models to calculate simple efficiency considering time lag effect. However, these models can’t discriminate efficient DMUs because of the nature of basic DEA model in which efficiency scores are limited to ‘1’. That is, efficient DMUs can’t be discriminated because their efficiency scores are same. Thus, this paper suggests a super-efficiency model for efficiency evaluation under the consideration of time lag effect based on the MpO model. A case example using a long term research project is given to compare the suggested model with the MpO model.
Abstract: This research was aimed at determining the impact of conservation techniques including bench terrace, stone terrace, mulching, grass strip and intercropping on soil erosion at tobacco-based farming system at Progo Hulu subwatershed, Central Java, Indonesia. Research was conducted from September 2007 to September 2009, located at Progo Hulu subwatershed, Central Java, Indonesia. Research site divided into 27 land units, and experimental fields were grouped based on the soil type and slope, ie: 30%, 45% and 70%, with the following treatments: 1) ST0= stone terrace (control); 2) ST1= stone terrace + Setaria spacelata grass strip on a 5 cm height dike at terrace lips + tobacco stem mulch with dose of 50% (7 ton/ ha); 3) ST2= stone terrace + Setaria spacelata grass strip on a 5 cm height dike at terrace lips + tobacco stem mulch with dose of 100% (14 ton/ ha); 4) ST3= stone terrace + tobacco and red bean intercropping + tobacco stem mulch with dose of 50% (7 ton/ ha). 5) BT0= bench terrace (control); 6) BT1= bench terrace + Setaria spacelata grass strip at terrace lips + tobacco stem mulch with dose of 50% (7 ton/ ha); 7) BT2= bench terrace + Setaria spacelata grass strip at terrace lips + tobacco stem mulch with dose of 100% (14 ton/ ha); 8) BT3= bench terrace + tobacco and red bean intercropping + tobacco stem mulch with dose of 50% (7 ton/ ha). The results showed that the actual erosion rates of research site were higher than that of tolerance erosion with mean value 89.08 ton/ha/year and 33.40 ton/ha/year, respectively. These resulted in 69% of total research site (5,119.15 ha) highly degraded. Conservation technique of ST2 was the most effective in suppressing soil erosion, by 42.87%, following with BT2 as much 30.63%. Others suppressed erosion only less than 21%.
Abstract: Study was conducted to determine the concentration of
copper, cadmium, lead and zinc in Cabomba furcata that found
abundance in Lake Chini. This aquatic plant was collected randomly
within the lake for heavy metal determination. Water quality
measurement was undertaken in situ for temperature, pH,
conductivity and dissolved oksigen using portable multi sensor probe
YSI model 556. The C. furcata was digested using wet digestion
method and heavy metal concentrations were analysed using Atomic
Absorption Spectrometer (AAS) Perkin Elmer 4100B (flame
method). Result of water quality classify Lake Chini between class II
to class III using Malaysian Water Quality Standard. According to
this standard, Lake Chini has moderate quality, which normal for
natural lake. Heavy metal concentrations in C.furcata were low and
found to be lower than the critical toxic value in aquatic plants. Oneway
ANOVA test indicated the heavy metal concentrations in
C.furcata were significantly differ between sampling location. Water
quality and heavy metal concentrations indicates that Lake Chini was
not receives anthropogenic load from nearby activities.
Abstract: In this paper, the existence of multiple positive
solutions for a class of third-order three-point discrete boundary value
problem is studied by applying algebraic topology method.
Abstract: In this paper we present a new approach to deal with
image segmentation. The fact that a single segmentation result do not
generally allow a higher level process to take into account all the
elements included in the image has motivated the consideration of
image segmentation as a multiobjective optimization problem. The
proposed algorithm adopts a split/merge strategy that uses the result
of the k-means algorithm as input for a quantum evolutionary
algorithm to establish a set of non-dominated solutions. The
evaluation is made simultaneously according to two distinct features:
intra-region homogeneity and inter-region heterogeneity. The
experimentation of the new approach on natural images has proved
its efficiency and usefulness.
Abstract: Motor imagery classification provides an important basis for designing Brain Machine Interfaces [BMI]. A BMI captures and decodes brain EEG signals and transforms human thought into actions. The ability of an individual to control his EEG through imaginary mental tasks enables him to control devices through the BMI. This paper presents a method to design a four state BMI using EEG signals recorded from the C3 and C4 locations. Principle features extracted through principle component analysis of the segmented EEG are analyzed using two novel classification algorithms using Elman recurrent neural network and functional link neural network. Performance of both classifiers is evaluated using a particle swarm optimization training algorithm; results are also compared with the conventional back propagation training algorithm. EEG motor imagery recorded from two subjects is used in the offline analysis. From overall classification performance it is observed that the BP algorithm has higher average classification of 93.5%, while the PSO algorithm has better training time and maximum classification. The proposed methods promises to provide a useful alternative general procedure for motor imagery classification
Abstract: The objective of the present investigation was to
evaluate the morphology of Escherchia coli bacteria in interaction
with SiO2 nanoparticles.
This study was made by atomic force microscopy and quartz
crystal microbalance using SiO2 nanoparticles with 10nm, 50nm and
100nm diameter and bacteria immobilized on polyelectrolyte
multilayer films obtained by spin coating or by “layer by layer”
(LbL) method.
Abstract: System testing is actually done to the entire system
against the Functional Requirement Specification and/or the System
Requirement Specification. Moreover, it is an investigatory testing
phase, where the focus is to have almost a destructive attitude and
test not only the design, but also the behavior and even the believed
expectations of the customer. It is also intended to test up to and
beyond the bounds defined in the software/hardware requirements
specifications. In Motorola®, Automated Testing is one of the testing
methodologies uses by GSG-iSGT (Global Software Group - iDEN
TM
Subcriber Group-Test) to increase the testing volume, productivity
and reduce test cycle-time in iDEN
TM
phones testing. Testing is able
to produce more robust products before release to the market. In this
paper, iHopper is proposed as a tool to perform stress test on iDEN
TM
phonse. We will discuss the value that automation has brought to
iDEN
TM
Phone testing such as improving software quality in the
iDEN
TM
phone together with some metrics. We will also look into
the advantages of the proposed system and some discussion of the
future work as well.
Abstract: A new deployment of the multiple criteria decision
making (MCDM) techniques: the Simple Additive Weighting
(SAW), and the Technique for Order Preference by Similarity to
Ideal Solution (TOPSIS) for portfolio allocation, is demonstrated in
this paper. Rather than exclusive reference to mean and variance as in
the traditional mean-variance method, the criteria used in this
demonstration are the first four moments of the portfolio distribution.
Each asset is evaluated based on its marginal impacts to portfolio
higher moments that are characterized by trapezoidal fuzzy numbers.
Then centroid-based defuzzification is applied to convert fuzzy
numbers to the crisp numbers by which SAW and TOPSIS can be
deployed. Experimental results suggest the similar efficiency of these
MCDM approaches to selecting dominant assets for an optimal
portfolio under higher moments. The proposed approaches allow
investors flexibly adjust their risk preferences regarding higher
moments via different schemes adapting to various (from
conservative to risky) kinds of investors. The other significant
advantage is that, compared to the mean-variance analysis, the
portfolio weights obtained by SAW and TOPSIS are consistently
well-diversified.
Abstract: Multi-user interference (MUI) is the main reason of system deterioration in the Spectral Amplitude Coding Optical Code Division Multiple Access (SAC-OCDMA) system. MUI increases with the number of simultaneous users, resulting into higher probability bit rate and limits the maximum number of simultaneous users. On the other hand, Phase induced intensity noise (PIIN) problem which is originated from spontaneous emission of broad band source from MUI severely limits the system performance should be addressed as well. Since the MUI is caused by the interference of simultaneous users, reducing the MUI value as small as possible is desirable. In this paper, an extensive study for the system performance specified by MUI and PIIN reducing is examined. Vectors Combinatorial (VC) codes families are adopted as a signature sequence for the performance analysis and a comparison with reported codes is performed. The results show that, when the received power increases, the PIIN noise for all the codes increases linearly. The results also show that the effect of PIIN can be minimized by increasing the code weight leads to preserve adequate signal to noise ratio over bit error probability. A comparison study between the proposed code and the existing codes such as Modified frequency hopping (MFH), Modified Quadratic- Congruence (MQC) has been carried out.
Abstract: A way of achieving nanodimentional structural elements in high carbon steel by special kind of heat treatment and cold plastic deformation is being explored. This leads to increasing interlamellar spacing of ferrite-carbide mixture. Decreasing the interlamellar spacing with cooling temperature increasing is determined. Experiments confirm such interlamellar spacing with which high carbon steel demonstrates the highest treatment and hardening capability. Total deformation degree effect on interlamellar spacing value in a ferrite-carbide mixture is obtained. Mechanical experiments results show that high carbon steel after heat treatment and repetitive cold plastic deformation possesses high tensile strength and yield strength keeping good percentage elongation.
Abstract: This article describes Uruk, the virtual museum of
Iraq that we developed for visual exploration and retrieval of image
collections. The system largely exploits the loosely-structured
hierarchy of XML documents that provides a useful representation
method to store semi-structured or unstructured data, which does not
easily fit into existing database. The system offers users the
capability to mine and manage the XML-based image collections
through a web-based Graphical User Interface (GUI). Typically, at an
interactive session with the system, the user can browse a visual
structural summary of the XML database in order to select interesting
elements. Using this intermediate result, queries combining structure
and textual references can be composed and presented to the system.
After query evaluation, the full set of answers is presented in a visual
and structured way.
Abstract: This paper proposes a method that predicts attractive
evaluation objects. In the learning phase, the method inductively
acquires trend rules from complex sequential data. The data is
composed of two types of data. One is numerical sequential data.
Each evaluation object has respective numerical sequential data. The
other is text sequential data. Each evaluation object is described in
texts. The trend rules represent changes of numerical values related
to evaluation objects. In the prediction phase, the method applies
new text sequential data to the trend rules and evaluates which
evaluation objects are attractive. This paper verifies the effect of the
proposed method by using stock price sequences and news headline
sequences. In these sequences, each stock brand corresponds to an
evaluation object. This paper discusses validity of predicted attractive
evaluation objects, the process time of each phase, and the possibility
of application tasks.
Abstract: The purpose of this paper is to detect human in images.
This paper proposes a method for extracting human body feature descriptors consisting of projected edge component series. The feature descriptor can express appearances and shapes of human with local
and global distribution of edges. Our method evaluated with a linear SVM classifier on Daimler-Chrysler pedestrian dataset, and test with
various sub-region size. The result shows that the accuracy level of
proposed method similar to Histogram of Oriented Gradients(HOG)
feature descriptor and feature extraction process is simple and faster than existing methods.
Abstract: In this paper, we have focused on study of swelling kinetics and salt-sensitivity behavior of a superabsorbing hydrogel based on carboxymethylcellulose (CMC) and acrylic acid and 2- Buthyl methacrylate. The swelling kinetics of the hydrogels with various particle sizes was preliminary investigated as well. The swelling of the hydrogel showed a second order kinetics of swelling in water. In addition, swelling measurements of the synthesized hydrogels in various chloride salt solutions was measured. Results indicated that a swelling-loss with an increase in the ionic strength of the salt solutions.
Abstract: Groundwater is one of the most important water
resources in Fars province. Based on this study, 95 percent of the
total annual water consumption in Fars is used for agriculture,
whereas the percentages for domestic and industrial uses are 4 and 1
percent, respectively. Population growth, urban and industrial
growth, and agricultural development in Fars have created a
condition of water stress. In this province, farmers and other users are
pumping groundwater faster than its natural replenishment rate,
causing a continuous drop in groundwater tables and depletion of this
resource. In this research variation of groundwater level, their effects
and ways to help control groundwater levels in aquifer of the Kavar-
Maharloo plains in Fars plain were evaluated .Excessive
exploitation of groundwater in this aquifer caused the groundwater
levels fall too fast or to unacceptable levels. The average drawdown
of the groundwater level in this plain were 17 meters during
1995 to 2006. The purpose of this study is to evaluate water level
changes in the Kavar-Maharloo Aquifer in the Fars province in order
to determine the areas of greatest depletion, the cause of depletion,
and predict the remaining life of the aquifer.