Abstract: In order to efficiently solve the problems created by the deepening energy crisis affecting Europe and the world,
governments cannot neglect the opportunities of using the energy
produced by sun collectors. In many of the EU countries there are sun
collectors producing heat energy, e.g. in 2011 in the area of EU27
(countries which belong to European Union) + Switzerland altogether
37519126 m2 were operated, which are capable of producing 26.3
GWh heat energy. The energy produced by these sun collectors is
utilized at the place of production. In the near future governments
will have to focus more on spreading and using sun collectors.
Among the complex problems of operating sun collectors, this article
deals with determining the optimal tilt angle, directions of sun
collectors. We evaluate the contamination of glass surface of sun
collector to the produced energy. Our theoretically results are confirmed by laboratory measurements. The purpose of our work is to help users and engineers in determination of optimal operation
parameters of sun collectors.
Abstract: This paper deals with the issue of biomass and sorted
municipal waste gasification and cogeneration using hot-air turbo-set.
It brings description of designed pilot plant with electrical output 80
kWe. The generated gas is burned in secondary combustion chamber
located beyond the gas generator. Flue gas flows through the heat
exchanger where the compressed air is heated and consequently
brought to a micro turbine. Except description, this paper brings our
basic experiences from operating of pilot plant (operating parameters,
contributions, problems during operating, etc.). The principal
advantage of the given cycle is the fact that there is no contact
between the generated gas and the turbine. So there is no need for
costly and complicated gas cleaning which is the main source of
operating problems in direct use in combustion engines because the
content of impurities in the gas causes operation problems to the units
due to clogging and tarring of working surfaces of engines and
turbines, which may lead as far as serious damage to the equipment
under operation. Another merit is the compact container package
making installation of the facility easier or making it relatively more
mobile. We imagine, this solution of cogeneration from biomass or
waste can be suitable for small industrial or communal applications,
for low output cogeneration.
Abstract: The article demonstrates on a case study how it is
possible to identify MSD risk. It is based on a dissertation Risk
identification model of occupational diseases formation in relation to
the work activity that determines what risk can endanger workers who
are exposed to the specific risk factors. It is evaluated based on
statistical calculations. These risk factors are main cause of upperextremities
musculoskeletal disorders.
Abstract: The Sigma-Delta A/D converters have been proposed
as a practical application for A/D conversion at high rates because of
its simplicity and robustness to imperfections in the circuit, also
because the traditional converters are more difficult to implement in
VLSI technology. These difficulties with conventional conversion
methods need precise analog components in their filters and
conversion circuits, and are more vulnerable to noise and
interference. This paper aims to analyze the architecture, function and
application of Analog-Digital converters (A/D) Sigma-Delta to
overcome these difficulties, showing some simulations using the
Simulink software and Multisim.
Abstract: This research is aimed to develop the online-class
scheduling management system and improve as a complex problem
solution, this must take into consideration in various conditions and
factors. In addition to the number of courses, the number of students
and a timetable to study, the physical characteristics of each class
room and regulations used in the class scheduling must also be taken
into consideration. This system is developed to assist management in
the class scheduling for convenience and efficiency. It can provide
several instructors to schedule simultaneously. Both lecturers and
students can check and publish a timetable and other documents
associated with the system online immediately. It is developed in a
web-based application. PHP is used as a developing tool. The
database management system was MySQL. The tool that is used for
efficiency testing of the system is questionnaire. The system was
evaluated by using a Black-Box testing. The sample was composed
of 2 groups: 5 experts and 100 general users. The average and the
standard deviation of results from the experts were 3.50 and 0.67.
The average and the standard deviation of results from the general
users were 3.54 and 0.54. In summary, the results from the research
indicated that the satisfaction of users were in a good level.
Therefore, this system could be implemented in an actual workplace
and satisfy the users’ requirement effectively.
Abstract: A simple, accurate and precise direct spectrophotometric method has been developed for the determination of cefixime in tablets and capsules. The method is based on the reaction of cefixime with a mixture of potassium iodide and potassium iodate to form yellow coloured product in ethanol-distilled water medium at room temperature which absorbed maximally at 352 nm. The factors affecting the reaction product were carefully studied and optimized. The validation parameters based on International Conference on Harmonisation (ICH, USA) guidelines were followed. The effect of common excipients used as additives has been tested and the tolerance limit was calculated for the determination of cefixime. Beer’s law is obeyed in the concentration range of 4 – 24 ug mL-1 with apparent molar absorptivity of 1.52 × 104 L mol-1cm-1 and Sandell’s sensitivity of 0.033 ug/cm2/ 0.001 absorbance unit. The limits of detection and quantitation for the proposed method are 0.32 and 1.06 ug mL-1, respectively. The proposed method has been successfully applied for the determination of cefixime in pharmaceutical formulations. The results obtained by the proposed method were statistically compared with the reference method using t- and F- values and found no significant difference between the two methods. The proposed method can be used as an alternate method for routine quality control analysis of cefixime in pharmaceutical formulations.
Abstract: Chloride resistance in Ultra High Performance
Concrete (UHPC) is determined in this paper. This work deals with
the one dimension chloride transport, which can be potentially
dangerous particularly for the durability of concrete structures. Risk
of reinforcement corrosion due to exposure to the concrete surface to
direct the action of chloride ions (mainly in the form de-icing salts or
groundwater) is dangerously increases. The measured data are
investigated depending on the depth of penetration of chloride ions
into the concrete structure. Comparative measurements with normal
strength concrete are done as well. The experimental results showed
that UHCP have improved resistance of chlorides penetration than
NSC and also chloride diffusion depth is significantly lower in
UHCP.
Abstract: The aim of this work is to present a theoretical analysis of a 2D ultrasound transducer comprised of crossed arrays of metal strips placed on both sides of thin piezoelectric layer (a). Such a structure is capable of electronic beam-steering of generated wavebeam both in elevation and azimuth. In this paper a semi-analytical model of the considered transducer is developed. It is based on generalization of the well-known BIS-expansion method. Specifically, applying the electrostatic approximation, the electric field components on the surface of the layer are expanded into fast converging series of double periodic spatial harmonics with corresponding amplitudes represented by the properly chosen Legendre polynomials. The problem is reduced to numerical solving of certain system of linear equations for unknown expansion coefficients.
Abstract: The use of permanent magnets (PM) is increasing in
permanent magnet synchronous machines (PMSM) to fulfill the
requirements of high efficiency machines in modern industry. PMSM
are widely used in industrial applications, wind power plants and the
automotive industry. Since PMSM are used in different
environmental conditions, the long-term effect of NdFeB-based
magnets at high temperatures and their corrosion behavior have to be
studied due to the irreversible loss of magnetic properties.
In this paper, the effect of magnetic properties due to corrosion
and increasing temperature in a climatic chamber has been presented.
The magnetic moment and magnetic field of the magnets were
studied experimentally.
Abstract: In this numerical study, we want to present the design
of highly efficient extruded-type heat sink. The symmetrically
arranged extruded-type heat sinks are used instead of a single extruded
or swaged-type heat sink. In this parametric study, the maximum
temperatures, the base temperatures between heaters, and the heat
release rates were investigated with respect to the arrangements of heat
sources, air flow rates, and amounts of heat input. Based on the results
we believe that the use of both side of heat sink is to be much better for
release the heat than the use of single side. Also from the results, it is
believed that the symmetric arrangement of heat sources is
recommended to achieve a higher heat transfer from the heat sink.
Abstract: In this study, the evaluation of thermal stability of the
micrometer-sized silica particle reinforced epoxy composite was
carried out through the measurement of thermal expansion coefficient
and Young’s modulus of the specimens. For all the specimens in this
study from the baseline to those containing 50 wt% silica filler, the
thermal expansion coefficients and the Young’s moduli were
gradually decreased down to 20% and increased up to 41%,
respectively. The experimental results were compared with fillervolume-
based simple empirical relations. The experimental results of
thermal expansion coefficients correspond with those of Thomas’s
model which is modified from the rule of mixture. However, the
measured result for Young’s modulus tends to be increased slightly.
The differences in increments of the moduli between experimental and
numerical model data are quite large.
Abstract: In addition to the production, which is already
frequently optimized, improving the distribution logistics also opens
up tremendous potential for increasing an enterprise’s
competitiveness. Here too though, numerous interactions need to be
taken into account, enterprises thus need to be able to identify and
weigh between different potentials for economically efficient
optimizations. In order to be able to assess potentials, enterprises
require a suitable method. This paper first briefly presents the need
for this research before introducing the procedure that will be used to
develop an appropriate method that not only considers interactions
but is also quickly and easily implemented.
Abstract: The aim of the present study is to investigate the
potential use of the selected seed oils. The oil was extracted using
Soxhlet apparatus and the physicochemical characteristics of the oil
determined using standard methods. The following results were
obtained for the physicochemical parameters analysed: for Egusi seed
oil, Oil yield 53.20%, Saponification value 178.03±1.25 mgKOH/g,
Iodine value 49.10±0.32 g I2/100g, Acid value 4.30±0.86 mgKOH/g,
and Peroxide value 5.80±0.27 meq/kg were obtained. For Pawpaw
seed oil, Oil yield 40.10%, Saponification value 24.13±3.93
mgKOH/g, Iodine value 24.87±0.19 g I2/100g, Acid value 9.46±0.40
mgKOH/g, and Peroxide value 3.12±1.22 meq/kg were obtained. For
Sweet orange seed oil, Oil yield 43.10%, Saponification value
106.30±2.37 mgKOH/g, Iodine value 37.08±0.04 g I2/100g, Acid
value 7.59±0.77 mgKOH/g, and Peroxide value 2.21±0.46 meq/kg
were obtained. From the obtained values of the determined
parameters, the oils can be extracted from the three selected seeds in
commercial quantities and that the egusi and sweet orange seed oils
may be utilized in the industrial soap production.
Abstract: Kinematic data wisely correlate vector quantities in
space to scalar parameters in time to assess the degree of symmetry
between the intact limb and the amputated limb with respect to a
normal model derived from the gait of control group participants.
Furthermore, these particular data allow a doctor to preliminarily
evaluate the usefulness of a certain rehabilitation therapy.
Kinetic curves allow the analysis of ground reaction forces (GRFs)
to assess the appropriateness of human motion.
Electromyography (EMG) allows the analysis of the fundamental
lower limb force contributions to quantify the level of gait
asymmetry. However, the use of this technological tool is expensive
and requires patient’s hospitalization. This research work suggests
overcoming the above limitations by applying artificial neural
networks.
Abstract: Over the past era, there have been a lot of efforts and
studies are carried out in growing proficient tools for performing
various tasks in big data. Recently big data have gotten a lot of
publicity for their good reasons. Due to the large and complex
collection of datasets it is difficult to process on traditional data
processing applications. This concern turns to be further mandatory
for producing various tools in big data. Moreover, the main aim of
big data analytics is to utilize the advanced analytic techniques
besides very huge, different datasets which contain diverse sizes from
terabytes to zettabytes and diverse types such as structured or
unstructured and batch or streaming. Big data is useful for data sets
where their size or type is away from the capability of traditional
relational databases for capturing, managing and processing the data
with low-latency. Thus the out coming challenges tend to the
occurrence of powerful big data tools. In this survey, a various
collection of big data tools are illustrated and also compared with the
salient features.
Abstract: In this study, a three dimensional numerical heat
transfer model has been used to simulate the laser structuring of
polymer substrate material in the Three-Dimensional Molded
Interconnect Device (3D MID) which is used in the advanced multifunctional
applications. A finite element method (FEM) transient
thermal analysis is performed using APDL (ANSYS Parametric
Design Language) provided by ANSYS. In this model, the effect of
surface heat source was modeled with Gaussian distribution, also the
effect of the mixed boundary conditions which consist of convection
and radiation heat transfers have been considered in this analysis. The
model provides a full description of the temperature distribution, as
well as calculates the depth and the width of the groove upon material
removal at different set of laser parameters such as laser power and
laser speed. This study also includes the experimental procedure to
study the effect of laser parameters on the depth and width of the
removal groove metal as verification to the modeled results. Good
agreement between the experimental and the model results is
achieved for a wide range of laser powers. It is found that the quality
of the laser structure process is affected by the laser scan speed and
laser power. For a high laser structured quality, it is suggested to use
laser with high speed and moderate to high laser power.
Abstract: With demand for primary energy continuously
growing, search for renewable and efficient energy sources has been
high on agenda of our society. One of the most promising energy
sources is biogas technology. Residues coming from dairy industry
and milk processing could be used in biogas production; however,
low efficiency and high cost impede wide application of such
technology. One of the main problems is management and conversion
of organic residues through the anaerobic digestion process which is
characterized by acidic environment due to the low whey pH (
Abstract: The measured data obtained from sensors in
continuous monitoring of civil structures are mainly used for modal
identification and damage detection. Therefore, when modal
identification analysis is carried out the quality in the identification of
the modes will highly influence the damage detection results. It is
also widely recognized that the usefulness of the measured data used
for modal identification and damage detection is significantly
influenced by the number and locations of sensors. The objective of
this study is the numerical implementation of two widely known
optimum sensor placement methods in beam-like structures.
Abstract: This paper reports the empirical investigation on the
effect of involuntary displacement of indigenous tribes on their sociocultural
and food practices. A descriptive research design using the
quantitative approach was applied and individual of indigenous tribes
as unit of analysis. Through a self-administered survey among two
selected Malaysia indigenous tribes, one hundred fifty questionnaires
were successfully collected. With the application of descriptive and
inferential statistic some useful insights pertaining to the issue
investigated was significantly obtained. Findings revealed that
improvement on the socio-culture, economy and knowledge is
apparent on the indigenous groups’ resulted from displacement
program. Displacement also has a slight impact on indigenous
groups’ food practices. These positive indications provide significant
implications, not only for the indigenous groups themselves, but also
for the responsible authorities.
Abstract: A total of 150 meat type chickens comprising 50 each
of Arbor Acre, Marshall and Ross were used for this study which
lasted for 10 weeks at the Federal University of Agriculture,
Abeokuta, Nigeria. Growth performance data were collected from the
third week through week 10 and data obtained were analysed using
the Generalized Linear Model Procedure. Heritability estimates (h2)
for body dimensions carried out on the chicken strains ranged from
low to high. Marshall broiler chicken strain had the highest h2 for
body weight 0.46±0.04, followed by Arbor Acre and Ross with h2
being 0.38±0.12 and 0.26±0.06, respectively. The repeatability
estimates for body weight in the three broiler strains were high, and it
ranged from 0.70 at week 4 to 0.88 at week 10. Relationships
between the body weight and linear body measurements in the broiler
chicken strains were positive and highly significant (p > 0.05).