Abstract: This paper concerns about the experimental and
numerical investigations of energy absorption and axial tearing
behaviour of aluminium 6060 circular thin walled tubes under static
axial compression. The tubes are received in T66 heat treatment
condition with fixed outer diameter of 42mm, thickness of 1.5mm
and length of 120mm. The primary variables are the conical die
angles (15°, 20° and 25°). Numerical simulations are carried on
ANSYS/LS-DYNA software tool, for investigating the effect of
friction between the tube and the die.
Abstract: It is well known that a linear dynamic system including
a delay will exhibit limit cycle oscillations when a bang-bang sensor
is used in the feedback loop of a PID controller. A similar behaviour
occurs when a delayed feedback signal is used to train a neural
network. This paper develops a method of predicting this behaviour
by linearizing the system, which can be shown to behave in a manner
similar to an integral controller. Using this procedure, it is possible
to predict the characteristics of the neural network driven limit cycle
to varying degrees of accuracy, depending on the information known
about the system. An application is also presented: the intelligent
control of a spark ignition engine.
Abstract: This article attempts to analyze functionally graded beam thermal buckling along with piezoelectric layers applying based on the third order shearing deformation theory considering various boundary conditions. The beam properties are assumed to vary continuously from the lower surface to the upper surface of the beam. The equilibrium equations are derived using the total potential energy equations, Euler equations, piezoelectric material constitutive equations and third order shear deformation theory assumptions. In order to fulfill such an aim, at first functionally graded beam with piezoelectric layers applying the third order shearing deformation theory along with clamped -clamped boundary conditions are thoroughly analyzed, and then following making sure of the correctness of all the equations, the very same beam is analyzed with piezoelectric layers through simply-simply and simply-clamped boundary conditions. In this article buckling critical temperature for functionally graded beam is derived in two different ways, without piezoelectric layer and with piezoelectric layer and the results are compared together. Finally, all the conclusions obtained will be compared and contrasted with the same samples in the same and distinguished conditions through tables and charts. It would be noteworthy that in this article, the software MAPLE has been applied in order to do the numeral calculations.
Abstract: The aim of this paper is to investigate the influence of
market share and diversification on the nonlife insurers- performance.
The underlying relationships have been investigated in different
industries and different disciplines (economics, management...), still,
no consistency exists either in the magnitude or statistical
significance of the relationship between market share (and
diversification as well) on one side and companies- performance on
the other side. Moreover, the direction of the relationship is also
somewhat questionable. While some authors find this relationship to
be positive, the others reveal its negative association. In order to test
the influence of market share and diversification on companies-
performance in Croatian nonlife insurance industry for the period
from 1999 to 2009, we designed an empirical model in which we
included the following independent variables: firms- profitability
from previous years, market share, diversification and control
variables (i.e. ownership, industrial concentration, GDP per capita,
inflation). Using the two-step generalized method of moments
(GMM) estimator we found evidence of a positive and statistically
significant influence of both, market share and diversification, on
insurers- profitability.
Abstract: The permanent magnet synchronous motor (PMSM) is
very useful in many applications. Vector control of PMSM is popular
kind of its control. In this paper, at first an optimal vector control for
PMSM is designed and then results are compared with conventional
vector control. Then, it is assumed that the measurements are noisy
and linear quadratic Gaussian (LQG) methodology is used to filter
the noises. The results of noisy optimal vector control and filtered
optimal vector control are compared to each other. Nonlinearity of
PMSM and existence of inverter in its control circuit caused that the
system is nonlinear and time-variant. With deriving average model,
the system is changed to nonlinear time-invariant and then the
nonlinear system is converted to linear system by linearization of
model around average values. This model is used to optimize vector
control then two optimal vector controls are compared to each other.
Simulation results show that the performance and robustness to noise
of the control system has been highly improved.
Abstract: Developments in scientific and technical area cause to use new methods and techniques in education, as is the case in all fields. Especially, the internet contributes a variety of new methods to design virtual and real time laboratory applications in education. In this study, a real time virtual laboratory is designed and implemented for analog and digital communications laboratory experiments by using Lab VIEW program for Marmara University Electronics-Communication Department. In this application, students can access the virtual laboratory web site and perform their experiments without any limitation of time and location so as the students can observe the signals by changing the parameters of the experiment and evaluate the results.
Abstract: The study was a case study analysis about Thai Asia
Pacific Brewery Company. The purpose was to analyze the
company’s marketing objective, marketing strategy at company level,
and marketing mix before liquor liberalization in 2000. Methods used
in this study were qualitative and descriptive research approach
which demonstrated the following results of the study demonstrated
as follows: (1) Marketing objective was to increase market share of
Heineken and Amtel, (2) the company’s marketing strategies were
brand building strategy and distribution strategy. Additionally, the
company also conducted marketing mix strategy as follows. Product
strategy: The company added more beer brands namely Amstel and
Tiger to provide additional choice to consumers, product and
marketing research, and product development. Price strategy: the
company had taken the following into consideration: cost,
competitor, market, economic situation and tax. Promotion strategy:
the company conducted sales promotion and advertising. Distribution
strategy: the company extended channels its channels of distribution
into food shops, pubs and various entertainment places. This strategy
benefited interested persons and people who were engaged in the beer
business.
Abstract: A multicriteria linear programming problem with integer variables and parameterized optimality principle "from lexicographic to Slater" is considered. A situation in which initial coefficients of penalty cost functions are not fixed but may be potentially a subject to variations is studied. For any efficient solution, appropriate measures of the quality are introduced which incorporate information about variations of penalty cost function coefficients. These measures correspond to the so-called stability and accuracy functions defined earlier for efficient solutions of a generic multicriteria combinatorial optimization problem with Pareto and lexicographic optimality principles. Various properties of such functions are studied and maximum norms of perturbations for which an efficient solution preserves the property of being efficient are calculated.
Abstract: A system for market identification (SMI) is presented.
The resulting representations are multivariable dynamic demand
models. The market specifics are analyzed. Appropriate models and
identification techniques are chosen. Multivariate static and dynamic
models are used to represent the market behavior. The steps of the
first stage of SMI, named data preprocessing, are mentioned. Next,
the second stage, which is the model estimation, is considered in more
details. Stepwise linear regression (SWR) is used to determine the
significant cross-effects and the orders of the model polynomials. The
estimates of the model parameters are obtained by a numerically stable
estimator. Real market data is used to analyze SMI performance.
The main conclusion is related to the applicability of multivariate
dynamic models for representation of market systems.
Abstract: In this research, the diffusion of innovation regarding
smartphone usage is analysed through a consumer behaviour theory.
This research aims to determine whether a pattern surrounding the
diffusion of innovation exists. As a methodology, an empirical study
of the switch from a conventional cell phone to a smartphone was
performed. Specifically, a questionnaire survey was completed by
general consumers, and the situational and behavioural characteristics
of switching from a cell phone to a smartphone were analysed. In
conclusion, we found that the speed of the diffusion of innovation, the
consumer behaviour characteristics, and the utilities of the product
vary according to the stage of the product life cycle.
Abstract: The utilization of cheese whey as a fermentation
substrate to produce bio-ethanol is an effort to supply bio-ethanol
demand as a renewable energy. Like other process systems, modeling
is also required for fermentation process design, optimization and
plant operation. This research aims to study the fermentation process
of cheese whey by applying mathematics and fundamental concept in
chemical engineering, and to investigate the characteristic of the
cheese whey fermentation process. Steady state simulation results for
inlet substrate concentration of 50, 100 and 150 g/l, and various
values of hydraulic retention time, showed that the ethanol
productivity maximum values were 0.1091, 0.3163 and 0.5639 g/l.h
respectively. Those values were achieved at hydraulic retention time
of 20 hours, which was the minimum value used in this modeling.
This showed that operating reactor at low hydraulic retention time
was favorable. Model of bio-ethanol production from cheese whey
will enhance the understanding of what really happen in the
fermentation process.
Abstract: Batch adsorption of recalcitrant melanoidin using the abundantly available coal fly ash was carried out. It had low specific surface area (SBET) of 1.7287 m2/g and pore volume of 0.002245 cm3/g while qualitative evaluation of the predominant phases in it was done by XRD analysis. Colour removal efficiency was found to be dependent on various factors studied. Maximum colour removal was achieved around pH 6, whereas increasing sorbent mass from 10g/L to 200 g/L enhanced colour reduction from 25% to 86% at 298 K. Spontaneity of the process was suggested by negative Gibbs free energy while positive values for enthalpy change showed endothermic nature of the process. Non-linear optimization of error functions resulted in Freundlich and Redlich-Peterson isotherms describing sorption equilibrium data best. The coal fly ash had maximum sorption capacity of 53 mg/g and could thus be used as a low cost adsorbent in melanoidin removal.
Abstract: This paper proposes an effective algorithm approach to hybrid control systems combining fuzzy logic and conventional control techniques of controlling the speed of induction motor assumed to operate in high-performance drives environment. The introducing of fuzzy logic in the control systems helps to achieve good dynamical response, disturbance rejection and low sensibility to parameter variations and external influences. Some fundamentals of the fuzzy logic control are preliminary illustrated. The developed control algorithm is robust, efficient and simple. It also assures precise trajectory tracking with the prescribed dynamics. Experimental results have shown excellent tracking performance of the proposed control system, and have convincingly demonstrated the validity and the usefulness of the hybrid fuzzy controller in high-performance drives with parameter and load uncertainties. Satisfactory performance was observed for most reference tracks.
Abstract: Despite so many years- development, the mainstream of workflow solutions from IT industries has not made ad-hoc workflow-support easy or inexpensive in MIS. Moreover, most of academic approaches tend to make their resulted BPM (Business Process Management) more complex and clumsy since they used to necessitate modeling workflow. To cope well with various ad-hoc or casual requirements on workflows while still keeping things simple and inexpensive, the author puts forth first the TSM design pattern that can provide a flexible workflow control while minimizing demand of predefinitions and modeling workflow, which introduces a generic approach for building BPM in workflow-aware MISs (Management Information Systems) with low development and running expenses.
Abstract: Discrete choice model is the most used methodology for studying traveler-s mode choice and demand. However, to calibrate the discrete choice model needs to have plenty of questionnaire survey. In this study, an aggregative model is proposed. The historical data of passenger volumes for high speed rail and domestic civil aviation are employed to calibrate and validate the model. In this study, different models are compared so as to propose the best one. From the results, systematic equations forecast better than single equation do. Models with the external variable, which is oil price, are better than models based on closed system assumption.
Abstract: Glomerular filtration rate (GFR) is a measure of
kidney function. It is usually estimated from serum concentrations of
cystatin C or creatinine although there has been considerable debate
in the literature about (i) the best equation to use and (ii) the
variability in the correlation between the concentrations of creatinine
and cystatin C. The equations for GFR can be written in a general
form and from these I calculate the error of the GFR estimates
associated with analyte measurement error. These show that the
error of the GFR estimates is such that it is not possible to distinguish
between the equations over much of the concentration range of either
analyte. The general forms of the equations are also used to derive
an expression for the concentration of cystatin C as a function of the
concentration of creatinine. This equation shows that these analyte
concentrations are not linearly related. Clinical reports of cystatin C
and creatinine concentration are consistent with the expression
derived.
Abstract: In this paper delamination phenomenon in
Carbon-Epoxy laminated composite material is investigated
numerically. Arcan apparatus and specimen is modeled in ABAQUS
finite element software for different loading conditions and crack
geometries. The influence of variation of crack geometry on
interlaminar fracture stress intensity factor and energy release rate for
various mixed mode ratios and pure mode I and II was studied. Also,
correction factors for this specimen for different crack length ratios
were calculated. The finite element results indicate that for loading
angles close to pure mode-II loading, a high ratio of mode-II to
mode-I fracture is dominant and there is an opposite trend for loading
angles close to pure mode-I loading. It confirms that by varying the
loading angle of Arcan specimen pure mode-I, pure mode-II and a
wide range of mixed-mode loading conditions can be created and
tested. Also, numerical results confirm that the increase of the mode-
II loading contribution leads to an increase of fracture resistance in
the CF/PEI composite (i.e., a reduction in the total strain energy
release rate) and the increase of the crack length leads to a reduction
of interlaminar fracture resistance in the CF/PEI composite (i.e., an
increase in the total interlaminar strain energy release rate).
Abstract: A framework to estimate the state of dynamically
varying environment where data are generated from heterogeneous
sources possessing partial knowledge about the environment is presented.
This is entirely derived within Dempster-Shafer and Evidence
Filtering frameworks. The belief about the current state is expressed
as belief and plausibility functions. An addition to Single Input
Single Output Evidence Filter, Multiple Input Single Output Evidence
Filtering approach is introduced. Variety of applications such as
situational estimation of an emergency environment can be developed
within the framework successfully. Fire propagation scenario is used
to justify the proposed framework, simulation results are presented.
Abstract: Carbon disulfide is widely used for the production of
viscose rayon, rubber, and other organic materials and it is a
feedstock for the synthesis of sulfuric acid. The objective of this
paper is to analyze possibilities for efficient production of CS2 from
sour natural gas reformation (H2SMR) (2H2S+CH4 =CS2 +4H2) .
Also, the effect of H2S to CH4 feed ratio and reaction temperature on
carbon disulfide production is investigated numerically in a
reforming reactor. The chemical reaction model is based on an
assumed Probability Density Function (PDF) parameterized by the
mean and variance of mixture fraction and β-PDF shape. The results
show that the major factors influencing CS2 production are reactor
temperature. The yield of carbon disulfide increases with increasing
H2S to CH4 feed gas ratio (H2S/CH4≤4). Also the yield of C(s)
increases with increasing temperature until the temperature reaches
to 1000°K, and then due to increase of CS2 production and
consumption of C(s), yield of C(s) drops with further increase in the
temperature. The predicted CH4 and H2S conversion and yield of
carbon disulfide are in good agreement with result of Huang and TRaissi.
Abstract: Recent advances in wireless sensor networks have led
to many routing methods designed for energy-efficiency in wireless
sensor networks. Despite that many routing methods have been
proposed in USN, a single routing method cannot be energy-efficient
if the environment of the ubiquitous sensor network varies. We present
the controlling network access to various hosts and the services they
offer, rather than on securing them one by one with a network security
model. When ubiquitous sensor networks are deployed in hostile
environments, an adversary may compromise some sensor nodes and
use them to inject false sensing reports. False reports can lead to not
only false alarms but also the depletion of limited energy resource in
battery powered networks. The interleaved hop-by-hop authentication
scheme detects such false reports through interleaved authentication.
This paper presents a LMDD (Low energy method for data delivery)
algorithm that provides energy-efficiency by dynamically changing
protocols installed at the sensor nodes. The algorithm changes
protocols based on the output of the fuzzy logic which is the fitness
level of the protocols for the environment.