Abstract: The effect of various humidities on process yields and
degrees of crystallinity for spray-dried powders from spray drying of
lactose with humid air in a straight-through system have been
studied. It has been suggested by Williams–Landel–Ferry kinetics
(WLF) that a higher particle temperature and lower glass-transition
temperature would increase the crystallization rate of the particles
during the spray-drying process. Freshly humidified air produced by
a Buchi-B290 spray dryer as a humidifier attached to the main spray
dryer decreased the particle glass-transition temperature (Tg), while
allowing the particle temperature (Tp) to reach higher values by using
an insulated drying chamber. Differential scanning calorimetry
(DSC) and moisture sorption analysis were used to measure the
degree of crystallinity for the spray-dried lactose powders. The
results showed that higher Tp-Tg, as a result of applying humid air,
improved the process yield from 21 ± 4 to 26 ± 2% and crystallinity
of the particles by decreasing the latent heat of crystallization from
43 ± 1 to 30 ± 11 J/g and the sorption peak height from 7.3 ± 0.7% to
6 ± 0.7%.
Abstract: An analysis of the Australian Diabetes Screening
Study estimated undiagnosed diabetes mellitus [DM] prevalence in a
high risk general practice based cohort. DM prevalence varied from
9.4% to 18.1% depending upon the diagnostic criteria utilised with
age being a highly significant risk factor. Utilising the gold standard
oral glucose tolerance test, the prevalence of DM was 22-23% in
those aged >= 70 years and
Abstract: The generalized wave equation models various
problems in sciences and engineering. In this paper, a new three-time
level implicit approach based on cubic trigonometric B-spline for the
approximate solution of wave equation is developed. The usual finite
difference approach is used to discretize the time derivative while
cubic trigonometric B-spline is applied as an interpolating function in
the space dimension. Von Neumann stability analysis is used to
analyze the proposed method. Two problems are discussed to exhibit
the feasibility and capability of the method. The absolute errors and
maximum error are computed to assess the performance of the
proposed method. The results were found to be in good agreement
with known solutions and with existing schemes in literature.
Abstract: One of the major goals of Spoken Dialog Systems
(SDS) is to understand what the user utters.
In the SDS domain, the Spoken Language Understanding (SLU)
Module classifies user utterances by means of a pre-definite
conceptual knowledge. The SLU module is able to recognize only the
meaning previously included in its knowledge base. Due the vastity
of that knowledge, the information storing is a very expensive
process.
Updating and managing the knowledge base are time-consuming
and error-prone processes because of the rapidly growing number of
entities like proper nouns and domain-specific nouns. This paper
proposes a solution to the problem of Name Entity Recognition
(NER) applied to a SDS domain. The proposed solution attempts to
automatically recognize the meaning associated with an utterance by
using the PANKOW (Pattern based Annotation through Knowledge
On the Web) method at runtime.
The method being proposed extracts information from the Web to
increase the SLU knowledge module and reduces the development
effort. In particular, the Google Search Engine is used to extract
information from the Facebook social network.
Abstract: This study aimed at designing and developing a
mechanical force gauge for the square watermelon mold for the first
time. It also tried to introduce the square watermelon characteristics
and its production limitations. The mechanical force gauge
performance and the product itself were also described. There are
three main designable gauge models: a. hydraulic gauge, b. strain
gauge, and c. mechanical gauge. The advantage of the hydraulic
model is that it instantly displays the pressure and thus the force
exerted by the melon. However, considering the inability to measure
forces at all directions, complicated development, high cost, possible
hydraulic fluid leak into the fruit chamber and the possible influence
of increased ambient temperature on the fluid pressure, the
development of this gauge was overruled. The second choice was to
calculate pressure using the direct force a strain gauge. The main
advantage of these strain gauges over spring types is their high
precision in measurements; but with regard to the lack of conformity
of strain gauge working range with water melon growth, calculations
were faced with problems. Finally the mechanical pressure gauge has
advantages, including the ability to measured forces and pressures on
the mold surface during melon growth; the ability to display the peak
forces; the ability to produce melon growth graph thanks to its
continuous force measurements; the conformity of its manufacturing
materials with the required physical conditions of melon growth; high
air conditioning capability; the ability to permit sunlight reaches the
melon rind (no yellowish skin and quality loss); fast and
straightforward calibration; no damages to the product during
assembling and disassembling; visual check capability of the product
within the mold; applicable to all growth environments (field,
greenhouses, etc.); simple process; low costs and so forth.
Abstract: This paper is concerned with the stability problem
with two additive time-varying delay components. By choosing one
augmented Lyapunov-Krasovskii functional, using some new zero
equalities, and combining linear matrix inequalities (LMI)
techniques, two new sufficient criteria ensuring the global stability
asymptotic stability of DNNs is obtained. These stability criteria are
present in terms of linear matrix inequalities and can be easily
checked. Finally, some examples are showed to demonstrate the
effectiveness and less conservatism of the proposed method.
Abstract: Male factor infertility due to endocrine disturbances
such as abnormalities in prolactin levels are encountered in a
significant proportion. This case control study was carried out to
determine the effects of prolactin on the male reproductive tract,
using 200 male white rats. The rats were maintained as the control
group (G1), hypoprolactinaemic group (G2), 3 hyperprolactinaemic
groups induced using oral largactil (G3), low dose fluphenazine (G4)
and high dose fluphenazine (G5). After 100 days, rats were subjected
to serum prolactin (PRL) level measurements and for basic seminal
fluid analysis (BSA). The difference between serum PRL
concentrations of rats in G2, G3, G4 and G5 as compared to the
control group were highly significant by Student’s t-test (p
Abstract: With the rapid progress of modern cities, the railway
construction must be developing quickly in China.As a typical
high-density country, shopping center on the subway should be one
important factor during the process of urban development. The paper
discusses the influence of the layout of shopping center on the subway,
and put it in the time and space’s axis of Shanghai urban development.
We usethe digital technology to establish the database of relevant
information. And then get the change role about shopping center on
subway in Shanghaiby the Kernel density estimate.The result shows
the development of shopping center on subway has a relationship with
local economic strength, population size, policysupport, and city
construction. And the suburbanization trend of shopping center would
be increasingly significant.By this case research, we could see the
Kernel density estimate is an efficient analysis method on the spatial
layout. It could reveal the characters of layout form of shopping center
on subway in essence. And it can also be applied to the other research
of space form.
Abstract: Lightning protection systems (LPS) for wind power
generation is becoming an important public issue. A serious damage
of blades, accidents where low-voltage and control circuit
breakdowns are frequently occur in many wind farms. A grounding
system is one of the most important components required for
appropriate LPSs in wind turbines WTs. Proper design of a wind
turbine grounding system is demanding and several factors for the
proper and effective implementation must taken into account. In this
paper proposed procedure of proper design of grounding systems for
a wind turbine was introduced. This procedure depends on measuring
of ground current of simulated wind farm under lightning taking into
consideration the soil ionization. The procedure also includes the
Ground Potential Rise (GPR) and the voltage distributions at ground
surface level and Touch potential. In particular, the contribution of
mitigating techniques, such as rings, rods and the proposed design
were investigated.
Abstract: The growth of wireless devices affects the availability
of limited frequencies or spectrum bands as it has been known that
spectrum bands are a natural resource that cannot be added.
Meanwhile, the licensed frequencies are idle most of the time.
Cognitive radio is one of the solutions to solve those problems.
Cognitive radio is a promising technology that allows the unlicensed
users known as secondary users (SUs) to access licensed bands
without making interference to licensed users or primary users (PUs).
As cloud computing has become popular in recent years, cognitive
radio networks (CRNs) can be integrated with cloud platform. One of
the important issues in CRNs is security. It becomes a problem since
CRNs use radio frequencies as a medium for transmitting and CRNs
share the same issues with wireless communication systems. Another
critical issue in CRNs is performance. Security has adverse effect to
performance and there are trade-offs between them. The goal of this
paper is to investigate the performance related to security trade-off in
CRNs with supporting cloud platforms. Furthermore, Queuing
Network Models with preemptive resume and preemptive repeat
identical priority are applied in this project to measure the impact of
security to performance in CRNs with or without cloud platform. The
generalized exponential (GE) type distribution is used to reflect the
bursty inter-arrival and service times at the servers. The results show
that the best performance is obtained when security is disabled and
cloud platform is enabled.
Abstract: This paper presents the design and analysis of Liquid
Crystal (LC) based tunable reflectarray antenna with different design
configurations within X-band frequency range. The effect of LC
volume used for unit cell element on frequency tunability and
reflection loss performance has been investigated. Moreover different
slot embedded patch element configurations have been proposed for
LC based tunable reflectarray antenna design with enhanced
performance. The detailed fabrication and measurement procedure
for different LC based unit cells has been presented. The waveguide
scattering parameter measured results demonstrated that by using the
circular slot embedded patch elements, the frequency tunability and
dynamic phase range can be increased from 180MHz to 200MHz and
120° to 124° respectively. Furthermore the circular slot embedded
patch element can be designed at 10GHz resonant frequency with a
patch volume of 2.71mm3 as compared to 3.47mm3 required for
rectangular patch without slot.
Abstract: This paper presents the voltage problem location
classification using performance of Least Squares Support Vector
Machine (LS-SVM) and Learning Vector Quantization (LVQ) in
electrical power system for proper voltage problem location
implemented by IEEE 39 bus New- England. The data was collected
from the time domain simulation by using Power System Analysis
Toolbox (PSAT). Outputs from simulation data such as voltage, phase
angle, real power and reactive power were taken as input to estimate
voltage stability at particular buses based on Power Transfer Stability
Index (PTSI).The simulation data was carried out on the IEEE 39 bus
test system by considering load bus increased on the system. To verify
of the proposed LS-SVM its performance was compared to Learning
Vector Quantization (LVQ). The results showed that LS-SVM is faster
and better as compared to LVQ. The results also demonstrated that the
LS-SVM was estimated by 0% misclassification whereas LVQ had
7.69% misclassification.
Abstract: In Egypt, girls have traditionally been educationally
disadvantaged. This disadvantage, however, has been focused on the
failure to enter school. Increasingly it is recognized that girls who
ever-enroll are at least as likely to complete primary and secondary
education as boys. Still the belief persists that girls, especially those
from poor families, will be disadvantaged in terms of school
expenditures and the transitions to secondary and higher education.
We examine expenditures on tutoring during the final year of
preparatory school, and the transition to specific tracks of secondary
education. Tests during the last year of preparatory largely determine
a student’s educational future. Results show that girls, even girls from
poor families, are not disadvantaged in terms of expenditures,
whether for tutoring, fees or general expenses. Moreover, girls are
more likely than boys to advance to general secondary education, the
track that leads to higher education.
Abstract: Recently, to cope with the rapidly changing
construction trend with aging infrastructures, modular bridge
technology has been studied actively. Modular bridge is easily
constructed by assembling standardized precast structure members in
the field. It will be possible to construct rapidly and reduce
construction cost efficiently. However, the shape of the transverse
connection of T-type girder newly developed between the segmented
modules is not verified. Therefore, the verification of the connection
shape is needed. In this study, shape of the modular T-girder bridge
transverse connection was analyzed by finite element model that was
verified in study which was verified model of transverse connection
using Abaqus. Connection angle was chosen as the parameter. The
result of analyses showed that optimal value of angle is 130 degree.
Abstract: A blood pressure monitor or sphygmomanometer can
be either manual or automatic, employing respectively either the
auscultatory method or the oscillometric method.
The manual version of the sphygmomanometer involves an
inflatable cuff with a stethoscope adopted to detect the sounds
generated by the arterial walls to measure blood pressure in an artery.
An automatic sphygmomanometer can be effectively used to
monitor blood pressure through a pressure sensor, which detects
vibrations provoked by oscillations of the arterial walls.
The pressure sensor implemented in this device improves the
accuracy of the measurements taken.
Abstract: Consumer-to-Consumer (C2C) E-commerce has been
growing at a very high speed in recent years. Since identical or
nearly-same kinds of products compete one another by relying on
keyword search in C2C E-commerce, some sellers describe their
products with spam keywords that are popular but are not related to
their products. Though such products get more chances to be retrieved
and selected by consumers than those without spam keywords,
the spam keywords mislead the consumers and waste their time.
This problem has been reported in many commercial services like
ebay and taobao, but there have been little research to solve this
problem. As a solution to this problem, this paper proposes a method
to classify whether keywords of a product are spam or not. The
proposed method assumes that a keyword for a given product is
more reliable if the keyword is observed commonly in specifications
of products which are the same or the same kind as the given
product. This is because that a hierarchical category of a product
in general determined precisely by a seller of the product and so is
the specification of the product. Since higher layers of the hierarchical
category represent more general kinds of products, a reliable degree
is differently determined according to the layers. Hence, reliable
degrees from different layers of a hierarchical category become
features for keywords and they are used together with features only
from specifications for classification of the keywords. Support Vector
Machines are adopted as a basic classifier using the features, since
it is powerful, and widely used in many classification tasks. In
the experiments, the proposed method is evaluated with a golden
standard dataset from Yi-han-wang, a Chinese C2C E-commerce,
and is compared with a baseline method that does not consider
the hierarchical category. The experimental results show that the
proposed method outperforms the baseline in F1-measure, which
proves that spam keywords are effectively identified by a hierarchical
category in C2C E-commerce.
Abstract: In the present study, M2 high speed steels were
fabricated by using electro-slag rapid remelting process. Carbide
structure was analysed and the fracture toughness and hardness were
also measured after austenitization treatment at 1190 and 1210oC
followed by tempering treatment at 535oC for billets with various
diameters from 16 to 60 mm. Electro-slag rapid remelting (ESRR)
process is an advanced ESR process combined by continuous casting
and successfully employed in this study to fabricate a sound M2 high
speed ingot. Three other kinds of commercial M2 high speed steels,
produced by traditional method, were also analysed for comparison.
Distribution and structure of eutectic carbides of the ESRR billet were
found to be comparable to those of commercial alloy and so was the
fracture toughness.
Abstract: Phase equilibria of AZ91D Mg alloys for
nonflammable use, containing Ca and Y, were carried out by using
FactSage® and FTLite database, which revealed that solid solution
treatment could be performed at temperatures from 400 to 450oC.
Solid solution treatment of AZ91D Mg alloy without Ca and Y was
successfully conducted at 420oC and supersaturated microstructure
with all beta phase resolved into matrix was obtained. In the case of
AZ91D Mg alloy with some Ca and Y; however, a little amount of
intermetallic particles were observed after solid solution treatment.
After solid solution treatment, each alloy was annealed at temperatures
of 180 and 200oC for time intervals from 1 min to 48 hrs and hardness
of each condition was measured by micro-Vickers method. Peak aging
conditions were deduced as at the temperature of 200oC for 10 hrs.
Abstract: In many communication and signal processing
systems, it is highly desirable to implement an efficient narrow-band
filter that decimate or interpolate the incoming signals. This paper
presents hardware efficient compensated CIC filter over a narrow
band frequency that increases the speed of down sampling by using
multiplierless decimation filters with polyphase FIR filter structure.
The proposed work analyzed the performance of compensated CIC
filter on the bases of the improvement of frequency response with
reduced hardware complexity in terms of no. of adders and
multipliers and produces the filtered results without any alterations.
CIC compensator filter demonstrated that by using compensation
with CIC filter improve the frequency response in passed of interest
26.57% with the reduction in hardware complexity 12.25%
multiplications per input sample (MPIS) and 23.4% additions per
input sample (APIS) w.r.t. FIR filter respectively.
Abstract: The ever increasing amount of solid waste (SW)
generated which is exacerbated by lack of proper waste management
system is of growing concern worldwide and in major cities in
developing countries due to its social, economic and environmental
implications. This study attempts to describe the aspects of solid
waste management (SWM) in Adama, one of the fast urbanizing
cities in Ethiopia, and highlights the challenges thereof. Data were
gathered through interview supplemented by field observation and
self-administered questionnaire. Then, the data were analyzed using
the Statistical Package for Social Science (SPSS) software. In
addition, secondary data were gathered from documents. Findings
revealed that the current SWM practice couldn’t cope with the fast
urbanizing needs and the rapid population growth exhibited by the
city. Besides, major factors contributing to the inefficient system
were identified. The study would provide practical insights to
decision makers in developing a sustainable SWM system leading to
minimized risk in the city.