Abstract: This paper presents the experimental results of
comparison between leakage currents and discharge currents. The leakage currents were obtained on polluted porcelain insulator.
Whereas, the discharge currents were obtained on lightly artificial
polluted porcelain specimen. The conducted measurements were
leakage current or discharge current and applied voltage. The insulator or specimen was in a hermetically sealed chamber, and the
current waveforms were analyzed using FFT.
The result indicated that the leakage current (LC) on low RH condition the fifth harmonic would be visible, and followed by the
seventh harmonic. The insulator had capacitive property. Otherwise,
on 99% relative humidity, the fifth harmonic would also be visible,
and the phase angle reached up to 12.2 degree. Whereas, on discharge current, the third harmonic would be visible, and followed
by fifth harmonic. The third harmonic would increase as pressure reduced. On this condition, the specimen had a non-linear characteristics
Abstract: Research results and optimal parameters investigation
of laser cut and profiling of diamond and quartz substrates by
femtosecond laser pulses are presented. Profiles 10 μm in width, ~25
μm in depth and several millimeters long were made. Investigation of
boundaries quality has been carried out with the use of AFM
«Vecco». Possibility of technological formation of profiles and
micro-holes in diamond and quartz substrates with nanometer-scale
boundaries is shown. Experimental results of multilayer dielectric
cover treatment are also presented. Possibility of precise upper layer
(thickness of 70–140 nm) removal is demonstrated. Processes of thin
metal film (60 nm and 350 nm thick) treatment are considered.
Isolation tracks (conductance ~ 10-11 S) 1.6–2.5 μm in width in
conductive metal layers are formed.
Abstract: The nickel and gold nanoclusters as supported
catalysts were analyzed by XAS, XRD and XPS in order to
determine their local, global and electronic structure. The present
study has pointed out a strong deformation of the local structure of
the metal, due to its interaction with oxide supports. The average
particle size, the mean squares of the microstrain, the particle size
distribution and microstrain functions of the supported Ni and Au
catalysts were determined by XRD method using Generalized Fermi
Function for the X-ray line profiles approximation. Based on EXAFS
analysis we consider that the local structure of the investigated
systems is strongly distorted concerning the atomic number pairs.
Metal-support interaction is confirmed by the shape changes of the
probability densities of electron transitions: Ni K edge (1s →
continuum and 2p), Au LIII-edge (2p3/2 → continuum, 6s, 6d5/2 and
6d3/2). XPS investigations confirm the metal-support interaction at
their interface.
Abstract: With respect to the dissipation of energy through
plastic deformation of joints of prefabricated wall units, the paper
points out the principal importance of efficient reinforcement of the
prefabricated system at its joints. The method, quality and amount of
reinforcement are essential for reaching the necessary degree of joint
ductility. The paper presents partial results of experimental research
of vertical joints of prefabricated units exposed to monotonously
rising loading and repetitive shear force and formulates a conclusion
that the limit state of the structure as a whole is preceded by the
disintegration of joints, or that the structure tends to pass from
linearly elastic behaviour to non-linearly elastic to plastic behaviour
by exceeding the proportional elastic limit in joints.Experimental
verification on a model of a 7-storey prefabricated structure revealed
weak points in its load-bearing systems, mainly at places of critical
points around openings situated in close proximity to vertical joints
of mutually perpendicularly oriented walls.
Abstract: Recently, Thai education system is engaged in serious and promising reforms. One of the crucial elements in most of these educational reforms is the teacher professional development. Teachers today are under growing pressure to perform. However, most new teachers are not adequately prepared to meet the expectation. Consequently, this paper seeks to investigate the opinion of mentor teachers and university supervisors about professional development in the aspect of learning management skill of the preservice teachers in Rajabhat Universities, then compare the opinion between the mentor teachers and university supervisors about professional development in the aspect of learning management skill of the pre-service teachers. The study involved a cohort of 40 university supervisors and 77 mentor teachers. The research concludes by showing that mentor teachers viewed pre-service teacher as a professional teacher with an effective learning management skill. However, in the perspective of the university supervisor, pre-service teachers still have inadequate learning management skill.
Abstract: This paper presents a methodology to harvest the kinetic energy of the raindrops using piezoelectric devices. In the study 1m×1m PVDF (Polyvinylidene fluoride) piezoelectric membrane, which is fixed by the four edges, is considered for the numerical simulation on deformation of the membrane due to the impact of the raindrops. Then according to the drop size of the rain, the simulation is performed classifying the rainfall types into three categories as light stratiform rain, moderate stratiform rain and heavy thundershower. The impact force of the raindrop is dependent on the terminal velocity of the raindrop, which is a function of raindrop diameter. The results were then analyzed to calculate the harvestable energy from the deformation of the piezoelectric membrane.
Abstract: In the numerical solution of the forward dynamics of a
multibody system, the positions and velocities of the bodies in the
system are obtained first. With the information of the system state
variables at each time step, the internal and external forces acting on
the system are obtained by appropriate contact force models if the
continuous contact method is used instead of a discrete contact
method. The local deformation of the bodies in contact, represented
by penetration, is used to compute the contact force. The ability and
suitability with current cylindrical contact force models to describe
the contact between bodies with cylindrical geometries with
particular focus on internal contacting geometries involving low
clearances and high loads simultaneously is discussed in this paper.
A comparative assessment of the performance of each model under
analysis for different contact conditions, in particular for very
different penetration and clearance values, is presented. It is
demonstrated that some models represent a rough approximation to
describe the conformal contact between cylindrical geometries
because contact forces are underestimated.
Abstract: One of the popular methods for recognition of facial
expressions such as happiness, sadness and surprise is based on
deformation of facial features. Motion vectors which show these
deformations can be specified by the optical flow. In this method, for
detecting emotions, the resulted set of motion vectors are compared
with standard deformation template that caused by facial expressions.
In this paper, a new method is introduced to compute the quantity of
likeness in order to make decision based on the importance of
obtained vectors from an optical flow approach. For finding the
vectors, one of the efficient optical flow method developed by
Gautama and VanHulle[17] is used. The suggested method has been
examined over Cohn-Kanade AU-Coded Facial Expression Database,
one of the most comprehensive collections of test images available.
The experimental results show that our method could correctly
recognize the facial expressions in 94% of case studies. The results
also show that only a few number of image frames (three frames) are
sufficient to detect facial expressions with rate of success of about
83.3%. This is a significant improvement over the available methods.
Abstract: Innovations in technology have created new ethical
challenges. Essential use of electronic communication in the
workplace has escalated at an astronomical rate over the past decade.
As such, legal and ethical dilemmas confronted by both the employer
and the employee concerning managerial control and ownership of einformation
have increased dramatically in the USA. From the
employer-s perspective, ownership and control of all information
created for the workplace is an undeniable source of economic
advantage and must be monitored zealously. From the perspective of
the employee, individual rights, such as privacy, freedom of speech,
and freedom from unreasonable search and seizure, continue to be
stalwart legal guarantees that employers are not legally or ethically
entitled to abridge in the workplace. These issues have been the
source of great debate and the catalyst for legal reform. The fine line
between ethical and legal has been complicated by emerging
technologies. This manuscript will identify and discuss a number of
specific legal and ethical issues raised by the dynamic electronic
workplace and conclude with suggestions that employers should
follow to respect the delicate balance between employees- legal
rights to privacy and the employer's right to protect its knowledge
systems and infrastructure.
Abstract: The special and unique advantages of explosive
forming, has developed its use in different industries. Considering the
important influence of improving the current explosive forming
techniques on increasing the efficiency and control over the
explosive forming procedure, the effects of air and water as the
energy-conveying medium, and also their differences will be
illustrated in this paper. Hence, a large number of explosive forming
tests have been conducted on two sizes of thin walled cylindrical
shells by using air and water as the working medium. Comparative
diagrams of the maximum radial deflection of work-pieces of the
same size, as a function of the scaled distance, show that for the
points with the same values of scaled distance, the maximum radial
deformation caused by the under water explosive loading is 4 to 5
times more than the deflection of the shells under explosive forming,
while using air. Results of this experimental research have also been
compared with other studies which show that using water as the
energy conveying media increases the efficiency up to 4.8 times. The
effect of the media on failure modes of the shells, and the necking
mechanism of the walls of the specimens, while being explosively
loaded, are also discussed in this issue. Measuring the tested
specimens shows that, the increase in the internal volume has been
accompanied by necking of the walls, which finally results in the
radial rupture of the structure.
Abstract: In this paper, a theoretical formula is presented to
predict the instantaneous folding force of the first fold creation in a
square column under axial loading. Calculations are based on analysis
of “Basic Folding Mechanism" introduced by Wierzbicki and
Abramowicz. For this purpose, the sum of dissipated energy rate under
bending around horizontal and inclined hinge lines and dissipated
energy rate under extensional deformations are equated to the work rate
of the external force on the structure. Final formula obtained in this
research, reasonably predicts the instantaneous folding force of the first
fold creation versus folding distance and folding angle and also predicts
the instantaneous folding force instead of the average value. Finally,
according to the calculated theoretical relation, instantaneous folding
force of the first fold creation in a square column was sketched
versus folding distance and was compared to the experimental results
which showed a good correlation.
Abstract: In inspection and workpiece localization, sampling point data is an important issue. Since the devices for sampling only sample discrete points, not the completely surface, sampling size and location of the points will be taken into consideration. In this paper a method is presented for determining the sampled points size and location for achieving efficient sampling. Firstly, uncertainty analysis of the localization parameters is investigated. A localization uncertainty model is developed to predict the uncertainty of the localization process. Using this model the minimum size of the sampled points is predicted. Secondly, based on the algebra theory an eigenvalue-optimal optimization is proposed. Then a freeform surface is used in the simulation. The proposed optimization is implemented. The simulation result shows its effectivity.
Abstract: In this paper a polymer electrolyte membrane (PEM)
fuel cell power system including burner, steam reformer, heat
exchanger and water heater has been considered to meet the
electrical, heating, cooling and domestic hot water loads of
residential building which in Tehran. The system uses natural gas as
fuel and works in CHP mode. Design and operating conditions of a
PEM fuel cell system is considered in this study. The energy
requirements of residential building and the number of fuel cell
stacks to meet them have been estimated. The method involved
exergy analysis and entropy generation thorough the months of the
year. Results show that all the energy needs of the building can be
met with 12 fuel cell stacks at a nominal capacity of 8.5 kW. Exergy
analysis of the CHP system shows that the increase in the ambient air
temperature from 1oC to 40oC, will have an increase of entropy
generation by 5.73%.Maximum entropy generates for 15 hour in 15th
of June and 15th of July is estimated to amount at 12624 (kW/K).
Entropy generation of this system through a year is estimated to
amount to 1004.54 GJ/k.year.
Abstract: The quality of a machined surface is becoming more and more important to justify the increasing demands of sophisticated component performance, longevity, and reliability. Usually, any machining operation leaves its own characteristic evidence on the machined surface in the form of finely spaced micro irregularities (surface roughness) left by the associated indeterministic characteristics of the different elements of the system: tool-machineworkpart- cutting parameters. However, one of the most influential sources in machining affecting surface roughness is the instantaneous state of tool edge. The main objective of the current work is to relate the in-process immeasurable cutting edge deformation and surface roughness to a more reliable easy-to-measure force signals using a robust non-linear time-dependent modeling regression techniques. Time-dependent modeling is beneficial when modern machining systems, such as adaptive control techniques are considered, where the state of the machined surface and the health of the cutting edge are monitored, assessed and controlled online using realtime information provided by the variability encountered in the measured force signals. Correlation between wear propagation and roughness variation is developed throughout the different edge lifetimes. The surface roughness is further evaluated in the light of the variation in both the static and the dynamic force signals. Consistent correlation is found between surface roughness variation and tool wear progress within its initial and constant regions. At the first few seconds of cutting, expected and well known trend of the effect of the cutting parameters is observed. Surface roughness is positively influenced by the level of the feed rate and negatively by the cutting speed. As cutting continues, roughness is affected, to different extents, by the rather localized wear modes either on the tool nose or on its flank areas. Moreover, it seems that roughness varies as wear attitude transfers from one mode to another and, in general, it is shown that it is improved as wear increases but with possible corresponding workpart dimensional inaccuracy. The dynamic force signals are found reasonably sensitive to simulate either the progressive or the random modes of tool edge deformation. While the frictional force components, feeding and radial, are found informative regarding progressive wear modes, the vertical (power) components is found more representative carrier to system instability resulting from the edge-s random deformation.
Abstract: For maintenance of a spine stability during the
postoperative period a transpedicular fixing of its elements is often
used. Usually the transpedicular systems are formed of rods which as
a result form a design of the frame type, fastening by screws to
vertebras. Such design should be rigid and perceive loadings
operating from the spine without essential deformations. From the
perfection point of view of known designs their stress
whole, and each of elements, in particular is of interest. In this study
the modeling of the transpedicular screw is performed and
estimation of its deformations taking into account interaction with a
vertebra body having variable structure is made.
Abstract: Titanium alloys like the modern alloy Ti 6Al 2Sn 4Zr 6Mo (Ti-6246) combine excellent specific mechanical properties and corrosion resistance. On the other hand,due to their material characteristics, machining of these alloys is difficult to perform. The aim of the current study is the analyses of wear mechanisms of coated cemented carbide tools applied in orthogonal cutting experiments of Ti-6246 alloy. Round bars were machined with standard coated tools in dry conditions on a CNC latheusing a wide range of cutting speeds and cutting depths. Tool wear mechanisms were afterwards investigated by means of stereo microscopy, optical microscopy, confocal microscopy and scanning electron microscopy. Wear mechanisms included fracture of the tool tip (total failure) and abrasion. Specific wear features like crater wear, micro cracks and built-up edgeformation appeared depending of the mechanical and thermal conditions generated in the workpiece surface by the cutting action.
Abstract: The improvement of quality of life is the main visible
integrated indicator of state well-being. More and more states pay
attention to define and to achieve social standards of quality of life as
social-economic strategy of development. These standards are
determinate by state features, complex of needs and interests of
individual, family and society.
It still remains in open question: “What is middle class" in
contemporary Kazakhstan. Appearance of new social standards of
quality of life is important indicator of its successful establishment.
The middle class as agent of social, politic and economic reforms
promotes to improve the quality of life of the country. But if consider
a low and a middle stratums of middle class, we can see that high
social expectations and real achievements are still significantly
different.
The article relies on the sociological data, collected during of
search of household-s standards of living in Almaty city and Almaty
region, and case-study of cottage city “Jana Kuat".
Abstract: Study is on the vibration of thin cylindrical shells made of a functionally gradient material (FGM) composed of stainless steel and nickel is presented. The effects of the FGM configuration are studied by studying the frequencies of FG cylindrical shells. In this case FG cylindrical shell has Nickel on its inner surface and stainless steel on its outer surface. The study is carried out based on third order shear deformation shell theory. The objective is to study the natural frequencies, the influence of constituent volume fractions and the effects of configurations of the constituent materials on the frequencies. The properties are graded in the thickness direction according to the volume fraction power-law distribution. Results are presented on the frequency characteristics, the influence of the constituent various volume fractions on the frequencies.
Abstract: Implementing quality assurance in higher education establishments is the main focus of the reform process currently undertaken by the Ministry of Higher Education and Scientific Research in the Kurdistan Region of Iraq. The reform agenda has involved attempts to improve academic quality and management processes in universities, technical institutions and colleges. The central challenge for the reform process is to produce change in higher education in a region where administration is described as centralized and bureaucratic. To make these changes, there should be a well-designed plans and follow up processes in order to monitor progress and develop responses to obstacles. Lack of skills, resources, political dilemmas, poor motivation, and readiness to face the consequences of change are factors which will determine the success of the reform process.