Abstract: High power laser – total emissivity method (HPL-TE method) for determination of coatings relative total emissivity dependent on the temperature is introduced. Method principle, experimental and evaluation parts of the method are described. Computer model of HPL-TE method is employed to perform the sensitivity analysis of the effect of method parameters on the sample surface temperature in the positions where the surface temperature and radiation heat flux are measured.
Abstract: The principal purpose of this article is to present a new method based on Adaptive Neural Network Fuzzy Inference System (ANFIS) to generate additional artificial earthquake accelerograms from presented data, which are compatible with specified response spectra. The proposed method uses the learning abilities of ANFIS to develop the knowledge of the inverse mapping from response spectrum to earthquake records. In addition, wavelet packet transform is used to decompose specified earthquake records and then ANFISs are trained to relate the response spectrum of records to their wavelet packet coefficients. Finally, an interpretive example is presented which uses an ensemble of recorded accelerograms to demonstrate the effectiveness of the proposed method.
Abstract: Dehydration process was carried out for tomato slices of var. Avinash after giving different pre-treatments such as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl). Untreated samples served as control. Solar drier and continuous conveyor (tunnel) drier were used for dehydration. Quality characteristics of tomato slices viz. moisture content, sugar, titratable acidity, lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning as affected by dehydration process were studied. Storage study was also carried out for a period of six months for tomato powder packed into different types of packaging materials viz. metalized polyester (MP) film and low density poly ethylene (LDPE). Changes in lycopene content and non-enzymatic browning (NEB) were estimated during storage at room temperature. Pretreatment of 5 mm thickness of tomato slices with calcium chloride in combination with potassium metabisulphite and drying using a tunnel drier with subsequent storage of product in metalized polyester bags was selected as the best process.
Abstract: Traffic incident has bad effect on all parts of society
so controlling road networks with enough traffic devices could help
to decrease number of accidents, so using the best method for
optimum site selection of these devices could help to implement good
monitoring system. This paper has considered here important criteria
for optimum site selection of traffic camera based on aggregation
methods such as Bagging and Dempster-Shafer concepts. In the first
step, important criteria such as annual traffic flow, distance from
critical places such as parks that need more traffic controlling were
identified for selection of important road links for traffic camera
installation, Then classification methods such as Artificial neural
network and Decision tree algorithms were employed for
classification of road links based on their importance for camera
installation. Then for improving the result of classifiers aggregation
methods such as Bagging and Dempster-Shafer theories were used.
Abstract: Advertising today has already become an integral part
of human life as a building block of the consumer community. A
component of the value chain of the media, advertising sector is
struggling increasingly harder to find new methods to reach
consumers. The tendency towards experimental marketing practices
is increasing day by day, especially to divert consumers from the idea
“They are selling something to me.” It is therefore considered a good
idea to investigate the trust in ad media of consumers, who are today
exposed to a great bulk of information from advertising sector.
In this study, the current value of ad media for the young
consumer will be investigated. Data on various ad media reliability
will be comparatively analyzed and young consumers will be traced
by including university students in the study. In this research, which
will be performed on students studying at the Selçuk University
(Turkey) by random sampling method, data will be obtained by
survey technique and evaluated by a statistical analysis.
Abstract: This paper presents a rule-based text- to- speech
(TTS) Synthesis System for Standard Malay, namely SMaTTS. The
proposed system using sinusoidal method and some pre- recorded
wave files in generating speech for the system. The use of phone
database significantly decreases the amount of computer memory
space used, thus making the system very light and embeddable. The
overall system was comprised of two phases the Natural Language
Processing (NLP) that consisted of the high-level processing of text
analysis, phonetic analysis, text normalization and morphophonemic
module. The module was designed specially for SM to overcome
few problems in defining the rules for SM orthography system before
it can be passed to the DSP module. The second phase is the Digital
Signal Processing (DSP) which operated on the low-level process of
the speech waveform generation. A developed an intelligible and
adequately natural sounding formant-based speech synthesis system
with a light and user-friendly Graphical User Interface (GUI) is
introduced. A Standard Malay Language (SM) phoneme set and an
inclusive set of phone database have been constructed carefully for
this phone-based speech synthesizer. By applying the generative
phonology, a comprehensive letter-to-sound (LTS) rules and a
pronunciation lexicon have been invented for SMaTTS. As for the
evaluation tests, a set of Diagnostic Rhyme Test (DRT) word list was
compiled and several experiments have been performed to evaluate
the quality of the synthesized speech by analyzing the Mean Opinion
Score (MOS) obtained. The overall performance of the system as
well as the room for improvements was thoroughly discussed.
Abstract: Word sense disambiguation is one of the most important open problems in natural language processing applications such as information retrieval and machine translation. Many approach strategies can be employed to resolve word ambiguity with a reasonable degree of accuracy. These strategies are: knowledgebased, corpus-based, and hybrid-based. This paper pays attention to the corpus-based strategy that employs an unsupervised learning method for disambiguation. We report our investigation of Latent Semantic Indexing (LSI), an information retrieval technique and unsupervised learning, to the task of Thai noun and verbal word sense disambiguation. The Latent Semantic Indexing has been shown to be efficient and effective for Information Retrieval. For the purposes of this research, we report experiments on two Thai polysemous words, namely /hua4/ and /kep1/ that are used as a representative of Thai nouns and verbs respectively. The results of these experiments demonstrate the effectiveness and indicate the potential of applying vector-based distributional information measures to semantic disambiguation.
Abstract: An application framework provides a reusable design
and implementation for a family of software systems. Application
developers extend the framework to build their particular
applications using hooks. Hooks are the places identified to show
how to use and customize the framework. Hooks define the
Framework Interface Classes (FICs) and the specifications of their
methods. As part of the development life cycle, it is required to test
the implementations of the FICs. Building a testing model to express
the behavior of a class is an essential step for the generation of the
class-based test cases. The testing model has to be consistent with the
specifications provided for the hooks. State-based models consisting
of states and transitions are testing models well suited to objectoriented
software. Typically, hand-construction of a state-based
model of a class behavior is expensive, error-prone, and may result in
constructing an inconsistent model with the specifications of the class
methods, which misleads verification results. In this paper, a
technique is introduced to automatically synthesize a state-based
testing model for FICs using the specifications provided for the
hooks. A tool that supports the proposed technique is introduced.
Abstract: For a quick and accurate calculation of spatial neutron
distribution in nuclear power reactors 3D nodal codes are usually
used aiming at solving the neutron diffusion equation for a given
reactor core geometry and material composition. These codes use a
second order polynomial to represent the transverse leakage term. In
this work, a nodal method based on the well known nodal expansion
method (NEM), developed at COPPE, making use of this polynomial
expansion was modified to treat the transverse leakage term for the
external surfaces of peripheral reflector nodes.
The proposed method was implemented into a computational
system which, besides solving the diffusion equation, also solves the
burnup equations governing the gradual changes in material
compositions of the core due to fuel depletion. Results confirm the
effectiveness of this modified treatment of peripheral nodes for
practical purposes in PWR reactors.
Abstract: This text studies glass bottle intelligent inspector
based machine vision instead of manual inspection. The system
structure is illustrated in detail in this paper. The text presents the
method based on watershed transform methods to segment the
possible defective regions and extract features of bottle wall by rules.
Then wavelet transform are used to exact features of bottle finish
from images. After extracting features, the fuzzy support vector
machine ensemble is putted forward as classifier. For ensuring that
the fuzzy support vector machines have good classification ability,
the GA based ensemble method is used to combining the several
fuzzy support vector machines. The experiments demonstrate that
using this inspector to inspect glass bottles, the accuracy rate may
reach above 97.5%.
Abstract: This paper reports a new application of material accounting techniques to characterise and quantify material stocks and flows at the “neighbourhood" scale. The study area is the main campus of the University of New South Wales in Sydney, Australia. The system boundary is defined by the urban structural unit (USU), a typological construct devised to facilitate assessment of the metabolism of urban systems. A streamlined material flow analysis (MFA) was applied to quantify the stocks and flows of key construction materials within the campus USU over time, drawing on empirical data from a major campus development project. The results are reviewed to assess the efficacy of the method in supporting urban environmental evaluation and design practice, for example to facilitate estimation of significant impacts such as greenhouse gas emissions. It is concluded that linking a service (in this case, teaching students) enabled by a given product (university buildings) to the amount of materials used in creating that product offers a potential way to reduce the environmental impact of that service, through more efficient use of materials.
Abstract: Chemical vapor deposition method was used to
produce carbon nanotubes on an iron based catalyst from acetylene.
Gas-phase samples collected from the different positions of the tubular reactor were analyzed by GC/MS. A variety of species ranging from hydrogen to naphthalene were observed and changes in their concentrations were plotted against the reactor position. Briefly benzene, toluene, styrene, indene and naphthalene were the main
higher molecular weight species and vinylacetylene and diacetylene were the important intermediates. Nanotube characterization was performed by scanning electron microscopy and transmission electron microscopy.
Abstract: The intention of this lessons is to assess the probability
of optical coherence tomography (OCT) for biometric recognition.
The OCT is the foundation on an optical signal acquisition and
processing method and has the micrometer-resolution. In this study,
we used the porcine skin for verifying the abovementioned means. The
porcine tissue was sound acknowledged for structural and
immunohistochemical similarity with human skin, so it could be
suitable for pre-clinical trial as investigational specimen. For this
reason, it was tattooed by the tattoo machine with the tattoo-pigment.
We detected the pattern of the tattooed skin by the OCT according to
needle speed. The result was consistent with the histology images.
This result showed that the OCT was effective to examine the tattooed
skin section noninvasively. It might be available to identify
morphological changes inside the skin.
Abstract: In this work, we treat the problems related to chemical and petrochemical plants of a certain complex process taking the centrifugal compressor as an example, a system being very complex by its physical structure as well as its behaviour (surge phenomenon). We propose to study the application possibilities of the recent control approaches to the compressor behaviour, and consequently evaluate their contribution in the practical and theoretical fields. Facing the studied industrial process complexity, we choose to make recourse to fuzzy logic for analysis and treatment of its control problem owing to the fact that these techniques constitute the only framework in which the types of imperfect knowledge can jointly be treated (uncertainties, inaccuracies, etc..) offering suitable tools to characterise them. In the particular case of the centrifugal compressor, these imperfections are interpreted by modelling errors, the neglected dynamics, no modelisable dynamics and the parametric variations. The purpose of this paper is to produce a total robust nonlinear controller design method to stabilize the compression process at its optimum steady state by manipulating the gas rate flow. In order to cope with both the parameter uncertainty and the structured non linearity of the plant, the proposed method consists of a linear steady state regulation that ensures robust optimal control and of a nonlinear compensation that achieves the exact input/output linearization.
Abstract: The environmental performance of rapeseed oil (RO)
and rapeseed methyl ester(RME) from winter rape as fuels produced
in Romanian agroclimate is analyzed in this paper. The proposed
methodology is life cycle assessment (LCA) and takes into
consideration the influence of grain production and agroclimatic
conditions. This study shows favorable results first for RO and then
for RME. When compared to diesel fuel, both studied biofuels show
better results in the following impact categories: Abiotic depletion
potential (ADP), Ozone layer depletion (ODP) and Photochemical
ozone creation potential (POCP).Furthermore, the environmental
performance of the two biofuels studied can be improved by
changing the type of fertilizer used and also by using biofuels instead
of diesel in the field works.
Abstract: In this paper, the problem of finding the optimal
topological configuration of a deregulated distribution network is
considered. The new features of this paper are proposing a multiobjective
function and its application on deregulated distribution
networks for finding the optimal configuration. The multi-objective
function will be defined for minimizing total Energy Supply Costs
(ESC) and energy losses subject to load flow constraints. The
optimal configuration will be obtained by using Binary Genetic
Algorithm (BGA).The proposed method has been tested to analyze a
sample and a practical distribution networks.
Abstract: This paper describes a combined mathematicalgraphical
approach for optimum tool path planning in order to
improve machining efficiency. A methodology has been used that
stabilizes machining operations by adjusting material removal rate in
pocket milling operations while keeping cutting forces within limits.
This increases the life of cutting tool and reduces the risk of tool
breakage, machining vibration, and chatter. Case studies reveal the
fact that application of this approach could result in a slight increase
of machining time, however, a considerable reduction of tooling cost,
machining vibration, noise and chatter can be achieved in addition to
producing a better surface finish.
Abstract: FACTS devices are used to control the power flow, to
increase the transmission capacity and to optimize the stability of the
power system. One of the most widely used FACTS devices is
Unified Power Flow Controller (UPFC). The controller used in the
control mechanism has a significantly effects on controlling of the
power flow and enhancing the system stability of UPFC. According
to this, the capability of UPFC is observed by using different control
mechanisms based on P, PI, PID and fuzzy logic controllers (FLC) in
this study. FLC was developed by taking consideration of Takagi-
Sugeno inference system in the decision process and Sugeno-s
weighted average method in the defuzzification process. Case studies
with different operating conditions are applied to prove the ability of
UPFC on controlling the power flow and the effectiveness of
controllers on the performance of UPFC. PSCAD/EMTDC program
is used to create the FLC and to simulate UPFC model.
Abstract: This research is to explore the satisfaction for senior
citizens on continuing education in Taiwan. The purpose of this
research aims at the difference on teacher-s teaching, personal
relationship, learning result, materials and environment. Through
different sexual and living area as the background variables, a
questionnaire is adopted as the methodology in this research. Three
results are found in this research. In overall, senior citizens taking
continuing education put the most important attention on personal
relationship but materials and leaning environment put the least. There
is a significant difference on personal relationship, teacher-s teaching
and research result between different sexes. Female senior citizens
attach more importance to teacher-s teaching and learning results but
male senior citizens value on personal relationship. Another
significant difference is shown on teacher-s teaching and personal
relationship because of senior citizens living area. Urban senior
citizens put importance on personal relationship and rural senior
citizens respect teacher-s teaching more.
Abstract: Worldwide conventional resources of fossil fuel are depleting very fast due to large scale increase in use of transport vehicles every year, therefore consumption rate of oil in transport sector alone has gone very high. In view of this, the major thrust has now been laid upon the search of alternative energy source and also for cost effective energy conversion system. The air converted into compressed form by non conventional or conventional methods can be utilized as potential working fluid for producing shaft work in the air turbine and thus offering the capability of being a zero pollution energy source. This paper deals with the mathematical modeling and performance evaluation of a small capacity compressed air driven vaned type novel air turbine. Effect of expansion action and steady flow work in the air turbine at high admission air pressure of 6 bar, for varying injection to vane angles ratios 0.2-1.6, at the interval of 0.2 and at different vane angles such as 30o, 45o, 51.4o, 60o, 72o, 90o, and 120o for 12, 8, 7, 6, 5, 4 and 3 vanes respectively at speed of rotation 2500 rpm, has been quantified and analyzed here. Study shows that the expansion power has major contribution to total power, whereas the contribution of flow work output has been found varying only up to 19.4%. It is also concluded that for variation of injection to vane angle ratios from 0.2 to 1.2, the optimal power output is seen at vane angle 90o (4 vanes) and for 1.4 to 1.6 ratios, the optimal total power is observed at vane angle 72o (5 vanes). Thus in the vaned type novel air turbine the optimum shaft power output is developed when rotor contains 4-5 vanes for almost all situations of injection to vane angle ratios from 0.2 to 1.6.