Abstract: Aluminum hybrid reinforcement technology is a
response to the dynamic ever increasing service requirements of such
industries as transportation, aerospace, automobile, marine, etc. It is
unique in that it offers a platform of almost unending combinations of
materials to produce various hybrid composites. This article reviews
the studies carried out on various combinations of aluminum hybrid
composite and the effects on mechanical, physical and chemical
properties. It is observed that the extent of enhancement of these
properties of hybrid composites is strongly dependent on the nature
of the reinforcement, its hardness, particle size, volume fraction,
uniformity of dispersion within the matrix and the method of hybrid
production.
Abstract: This paper represents performance of particle swarm
optimisation (PSO) algorithm based integral (I) controller and
proportional-integral controller (PI) for interconnected hydro-thermal
automatic generation control (AGC) with generation rate constraint
(GRC) and Thyristor controlled phase shifter (TCPS) in series with
tie line. The control strategy of TCPS provides active control of
system frequency. Conventional objective function integral square
error (ISE) and another objective function considering square of
derivative of change in frequencies of both areas and change in tie
line power are considered. The aim of designing the objective
function is to suppress oscillation in frequency deviations and change
in tie line power oscillation. The controller parameters are searched
by PSO algorithm by minimising the objective functions. The
dynamic performance of the controllers I and PI, for both the
objective functions, are compared with conventionally optimized I
controller.
Abstract: This paper reports the numerical and experimental
performances of Double Glass Wall are investigated. Two
configurations were considered namely, the Double Clear Glass Wall
(DCGW) and the Double Translucent Glass Wall (DTGW). The
coupled governing equations as well as boundary conditions are
solved using the finite element method (FEM) via COMSOLTM
Multiphysics. Temperature profiles and flow field of the DCGW and
DTGW are reported and discussed. Different constant heat fluxes
were considered as 400 and 800 W.m-2 the corresponding initial
condition temperatures were 30.5 and 38.5ºC respectively. The
results show that the simulation results are in agreement with the
experimental data. Conclusively, the model considered in this study
could reasonable be used simulate the thermal and ventilation
performance of the DCGW and DTGW configurations.
Abstract: Botnets are one of the most serious and widespread
cyber threats. Today botnets have been facilitating many
cybercrimes, especially financial, top secret thefts. Botnets can be
available for lease in the market and are utilized by the
cybercriminals to launch massive attacks like DDoS, click fraud,
phishing attacks etc., Several large institutions, hospitals, banks,
government organizations and many social networks such as twitter,
facebook etc., became the target of the botmasters. Recently,
noteworthy researches have been carried out to detect bot, C&C
channels, botnet and botmasters. Using many sophisticated
technologies, botmasters made botnet a titan of the cyber world.
Innumerable challenges have been put forth by the botmasters to the
researchers in the detection of botnet. In this paper we present a
survey of different types of botnet C&C channels and also provide a
comparison of various botnet categories. Finally we hope that our
survey will create awareness for forthcoming botnet research
endeavors.
Abstract: Two tragic tsunamis that devastated the west coast of
Sumatra Island, Indonesia in 2004 and North East Japan in 2011 had
damaged bridges to various extents. Tsunamis have resulted in the
catastrophic deterioration of infrastructures i.e. coastal structures,
utilities and transportation facilities. A bridge structure performs vital
roles to enable people to perform activities related to their daily needs
and for development. A damaged bridge needs to be repaired
expeditiously. In order to understand the effects of tsunami forces on
bridges, experimental tests are carried out to measure the
characteristics of hydrodynamic force at various wave heights.
Coastal bridge models designed at a 1:40 scale are used in a 24.0 m
long hydraulic flume with a cross section of 1.5 m by 2.0 m. The
horizontal forces and uplift forces in all cases show that forces
increase nonlinearly with increasing wave amplitude.
Abstract: The exposure to outdoor air pollution causes lung
cancer and increases the risk of bladder cancer. Because air pollution
in urban areas is mainly caused by transportation, it is necessary to
evaluate pollutant exhaust emissions from vehicles during their realworld
use. Nevertheless their evaluation and reduction is a key
problem, especially in the cities, that account for more than 50% of
world population.
A particular attention was given to the slope variability along the
streets during each journey performed by the instrumented vehicle.
In this paper we dealt with the problem of describing a
quantitatively approach for the reconstruction of GPS coordinates and
altitude, in the context of correlation study between driving cycles /
emission / geographical location, during an experimental campaign
realized with some instrumented cars.
Finally the slope analysis can be correlated to the emission and
consumption values in a specific road position, and it could be
evaluated its influence on their behaviour.
Abstract: Marine Protected Areas can benefit from nature based
tourism, monitoring environmental impacts and also become target
for human presence. From more than 3 million tourists visiting
Cozumel Island every year, an average of 2,8 million arrive by cruise
ship, and 41% are estimated to have motivation for water activities.
The destination is relying so much on the tourism activity, that scuba
diving and snorkeling in the National Park Reef of Cozumel sustain
the major economic activity. In order to achieve the sustainable
development indicator designed for regional environmental
development, the PNAC offers a training course to tourism providers
to access the protected area. This way, the update of the last 5 years
of such training is directed to diving staff, boat crew and
professionals, making them able to assist in managing the natural
resource. Moreover, the case study is an example to be used for
raising awareness among tourists visiting protected areas.
Abstract: Asphaltic concrete for pavement construction in India
are produced by using crushed stone, gravels etc. as aggregate. In
north-Eastern region of India, there is a scarcity of stone aggregate.
Therefore the road engineers are always in search of an optional
material as aggregate which can replace the regularly used material.
The purpose of this work was to evaluate the utilization of
substandard or marginal aggregates in flexible pavement
construction. The investigation was undertaken to evaluate the effects
of using lower quality aggregates such as over burnt brick aggregate
on the preparation of asphalt concrete for flexible pavements. The
scope of this work included a review of available literature and
existing data, a laboratory evaluation organized to determine the
effects of marginal aggregates and potential techniques to upgrade
these substandard materials, and a laboratory evaluation of these
upgraded marginal aggregate asphalt mixtures. Over burnt brick
aggregates are water susceptible and can leads to moisture damage.
Moisture damage is the progressive loss of functionality of the
material owing to loss of the adhesion bond between the asphalt
binder and the aggregate surface. Hence zycosoil as an anti striping
additive were evaluated in this study. This study summarizes the
results of the laboratory evaluation carried out to investigate the
properties of asphalt concrete prepared with zycosoil modified over
burnt brick aggregate. Marshall specimen were prepared with stone
aggregate, zycosoil modified stone aggregate, over burnt brick
aggregate and zycosoil modified over burnt brick aggregate. Results
show that addition of zycosoil with stone aggregate increased
stability by 6% and addition of zycosoil with over burnt brick
aggregate increased stability by 30%.
Abstract: The operation of nuclear power plants involves
continuous monitoring of the environment in their area. This
monitoring is performed using a complex data acquisition system,
which collects status information about the system itself and values
of many important physical variables e.g. temperature, humidity,
dose rate etc. This paper describes a proposal and optimization of
communication that takes place in teledosimetric system between the
central control server responsible for the data processing and storing
and the decentralized measuring stations, which are measuring the
physical variables. Analyzes of ongoing communication were
performed and consequently the optimization of the system
architecture and communication was done.
Abstract: Quality control helps industries in improvements of its
product quality and productivity. Statistical Process Control (SPC) is
one of the tools to control the quality of products that turning practice
in bringing a department of industrial engineering process under
control. In this research, the process control of a turning
manufactured at workshops machines. The varying measurements
have been recorded for a number of samples of a rice polished
cylinder obtained from a number of trials with the turning practice.
SPC technique has been adopted by the process is finally brought
under control and process capability is improved.
Abstract: Due to growing concern about environmental and
social consequences throughout the world, a need has been felt to
incorporate sustainability concepts in conventional manufacturing.
This paper is an attempt to identify and evaluate drivers in
implementing sustainable manufacturing in Indian context. Nine
possible drivers for successful implementation of sustainable
manufacturing have been identified from extensive review. Further,
Decision Making Trial and Evaluation Laboratory (DEMATEL)
approach has been utilized to evaluate and categorize these identified
drivers for implementing sustainable manufacturing in to the cause
and effect groups. Five drivers (Societal Pressure and Public
Concerns; Regulations and Government Policies; Top Management
Involvement, Commitment and Support; Effective Strategies and
Activities towards Socially Responsible Manufacturing and Market
Trends) have been categorized into the cause group and four drivers
(Holistic View in Manufacturing Systems; Supplier Participation;
Building Sustainable culture in Organization; and Corporate Image
and Benefits) have been categorized into the effect group. “Societal
Pressure and Public Concerns” has been found the most critical driver
and “Corporate Image and Benefits” as least critical or the most
easily influenced driver to implementing sustainable manufacturing
in Indian context. This paper may surely help practitioners in better
understanding of these drivers and their priorities towards effective
implementation of sustainable manufacturing.
Abstract: The influence of three different types of halloysite
nanotubes (HNTs) with different dimensions, namely as camel lake
(CLA), Jarrahdale (JA) and Matauri Bay (MB), on their reinforcing
ability of ethylene propylene dine monomer (EPDM) were
investigated by varying the HNTs loading (from 0-15 phr).
Mechanical properties of the nanocomposites improved with addition
of all three HNTs, but CLA based nanocomposites exhibited a
significant enhancement compared to the other HNTs. For instance,
tensile properties of EPDM nanocomposites increased by 120%,
256% and 340% for MB, JA and CLA, respectively, with addition of
15 phr of HNTs. This could be due to the higher aspect ratio and
higher surface area of CLA compared to others. Scanning electron
microscopy (SEM) of nanocomposites at 15 phr of HNT loadings
showed low amounts of pulled-out nanotubes which confirmed the
presence of more embedded nanotubes inside the EPDM matrix, as
well as aggregates within the fracture surface of EPDM/HNT
nanocomposites
Abstract: This paper evaluates the performance of a multi-lane
four legged modern roundabout operating in Muscat using SIDRA
model. The performance measures include Degree of Saturation
(DOS), average delay, and queue lengths. The geometric and traffic
data were used for model preparation. Gap acceptance parameters,
critical gap and follow up headway, were used for calibration of
SIDRA model. The results from the analysis showed that currently
the roundabout is experiencing delays up to 610 seconds per vehicle
with DOS 1.67 during peak hour. Further, sensitivity analysis for
general and roundabout parameters was performed, amongst lane
width, cruise speed, inscribed diameter, entry radius and entry angle
showed that inscribed diameter is most crucial factor affecting delay
and DOS. Up gradation of roundabout to fully signalized junction
was found as the suitable solution which will serve for future years
with LOS C for design year having DOS of 0.9 with average control
delay of 51.9 seconds per vehicle.
Abstract: This paper discusses the potential benefits of an
interactive multimedia information representation in enhancing
students’ critical thinking aligned with history reasoning in learning
history amongst Secondary School students in Malaysia. Two modes
of multimedia information representation were implemented;
chronologic and thematic information representations. A qualitative
study of an unstructured interview was conducted among two history
teachers, one history education lecturer, two i-think experts, and five
students from Form Four secondary school. The interview was to
elicit their opinions on the implementation of thinking maps and
interactive multimedia information representation in history learning.
The key elements of the interactive multimedia (e.g. multiple media,
user control, interactivity and use of timelines and concept maps)
were then considered to improve the learning process. Findings of the
preliminary investigation reveal that the interactive multimedia
information representations have the potential benefits to be
implemented as an instructional resource in enhancing students’
higher order thinking skills (HOTs). This paper concludes by giving
suggestions for future work.
Abstract: The present study involved analysis of certain
characteristics of the perennial ryegrass (Lolium perenne L.)
genotypes collected from the natural flora of Ankara, and explores a
correlation among them. In order to evaluate the plants for breeding
purpose as per Turkey's environmental conditions, the perennial
ryegrass plants were collected from natural pasture of Ankara in 2004
and were utilized for the study. Seeds of the collected plants were
sown in pots and seedlings were prepared in a greenhouse. In 2005,
the seedlings were transplanted at 50 × 50 cm2 intervals in
Randomized Complete Blocks Design in an experimental field. In
2007 and 2008, data were recorded from the observations and
measurements of 568 perennial ryegrasses. The plant characteristics,
which were investigated, included re-growth time in spring, color,
density, growth habit, tendency to form inflorescence, time of
inflorescence, plant height, length of upper internode, spike length,
leaf length, leaf width, leaf area, leaf shape, number of spikelets per
spike, seed yield per spike and 1000 grain weight and the correlation
analyses were made using this data. Correlation coefficients were
estimated between all paired combinations of the studied traits. The
yield components exhibited varying trends of association among
themselves. Seed yield per spike showed significant and positive
association with the number of spikelets per spike, 1000 grain weight,
plant height, length of upper internode, spike length, leaf length, leaf
width, leaf area and color, but significant and negative association
with the growth habit and re-growth time in spring.
Abstract: India holds 17.5% of the world’s population but has
only 2% of the total geographical area of the world where 27.35% of
the area is categorized as wasteland due to lack of or less
groundwater. So there is a demand for excessive groundwater for
agricultural and non agricultural activities to balance its growth rate.
With this in mind, an attempt is made to find the groundwater
potential zone in Gomukhi Nadhi sub basin of Vellar River basin,
TamilNadu, India covering an area of 1146.6 Sq.Km consists of 9
blocks from Peddanaickanpalayam to Virudhachalam in the sub
basin. The thematic maps such as Geology, Geomorphology,
Lineament, Landuse and Landcover and Drainage are prepared for
the study area using IRS P6 data. The collateral data includes rainfall,
water level, soil map are collected for analysis and inference. The
digital elevation model (DEM) is generated using Shuttle Radar
Topographic Mission (SRTM) and the slope of the study area is
obtained. ArcGIS 10.1 acts as a powerful spatial analysis tool to find
out the ground water potential zones in the study area by means of
weighted overlay analysis. Each individual parameter of the thematic
maps are ranked and weighted in accordance with their influence to
increase the water level in the ground. The potential zones in the
study area are classified viz., Very Good, Good, Moderate, Poor with
its aerial extent of 15.67, 381.06, 575.38, 174.49 Sq.Km respectively.
Abstract: Pesticides and drugs used in agriculture and veterinary
medicine may end up in aquatic environments and bioaccumulate in
the food chain, thus causing serious problems for fauna and human
health. For determination of the toxic effects of atrazine herbicide on
Caspian kutum, Rutilus frisii kutum larvae, the 96-h LC50 of atrazine
was measured for newly hatched larvae as 18.53 ppm. Toxicity of
atrazine herbicide on Caspian kutum larvae was investigated using
concentrations: 9.25ppm, 4.62 ppm and 2.31 ppm for 7 days.
Comparison of the length, weight and condition factor showed that
no significant differences between atrazine exposed and control
groups. The concentration of Na+, K+, Ca2+, Mg2+ and Cl- in whole
body of larvae in control and atrazine exposure groups were
measured and the results showed that concentrations of all these ions
is higher in atrazine exposure group than control group. It is obvious
from this study that atrazine negatively affects osmoregulation
process and changes ion compositions of the body even at sublethal
concentration and acute exposure but have no effects on growth
parameters of the body.
Abstract: Musculoskeletal injuries in school children could be
reduced improving trunk strength and hamstring flexibility. Low
levels of trunk muscle strength and hamstring flexibility may result in
acute and musculoskeletal chronic diseases. The Pilates Method can
be appropriate to improve these physical condition attributes and has
been rarely employed by this social group. On the other hand, it has
been shown that trunk strength and flexibility are different between
genders, but there is no evidence about the effect of exercise
programs designed to improve both items in school children.
Therefore the objective of this study was to measure the effect of a
six-week Pilates-based exercise program in 14 year old school
children trunk strength and hamstring flexibility, establishing
differences in gender. The sample was composed of 57 students
divided into experimental group (EG; n=30) and control group (CG;
n=27). Bench Trunk Curl test (BTC), Sörensen test and Toe-touch
test (TT) were used to measure dynamic muscular resistance in trunk
flexion, isometric strength in trunk extension and hamstring
flexibility, respectively. EG utilized the Pilates exercise program
during six-weeks (2 days/week, 55minutes/session). After this period
of training, EG improved trunk strength and hamstring flexibility
significantly but there were no significant differences within CG.
Although boys were better in BTC test and girls were better in TT
test, there were no significant differences between them.
Abstract: Energy consumption and users’ satisfaction were
compared in three LEED certified office buildings in turkey and an
office building in Egypt. The field studies were conducted in summer
2012. The measured environmental parameters in the four buildings
were indoor air temperature, relative humidity, CO2 percentage and
light intensity. The traditional building is located in Smart Village in
Abu Rawash, Cairo, Egypt. The building was studied for 7 days
resulting in 84 responds. The three rated buildings are in Istanbul;
Turkey. A Platinum LEED certified office building is owned by
BASF and gained a platinum certificate for new construction and
major renovation. The building was studied for 3 days resulting in 13
responds. A Gold LEED certified office building is owned by BASF
and gained a gold certificate for new construction and major
renovation. The building was studied for 2 days resulting in 10
responds. A silver LEED certified office building is owned by
Unilever and gained a silver certificate for commercial interiors. The
building was studied for 7 days resulting in 84 responds.
The results showed that all buildings had no significant difference
regarding occupants’ satisfaction with the amount of lighting, noise
level, odor and access to the outdoor view. There was significant
difference between occupants’ satisfaction in LEED certified
buildings and the traditional building regarding the thermal
environment and the perception of the general environment (colors,
carpet and decoration. The findings suggest that careful design could
lead to a certified building that enhances the thermal environment and
the perception of the indoor environment leading to energy
consumption without scarifying occupants’ satisfaction.
Abstract: The aim of the present work was to statistically design
an autotrophic medium for maximum biomass production by
Chlorella pyrenoidosa using response surface methodology. After
evaluating one factor at a time approach, K2HPO4, KNO3,
MgSO4.7H2O and NaHCO3 were preferred over the other
components of the fog’s medium as most critical autotrophic medium
components. The study showed that the maximum biomass yield was
achieved while the concentrations of MgSO4.7H2O, K2HPO4, KNO3
and NaHCO3 were 0.409 g/L, 0.24 g/L, 1.033 g/L, and 3.265 g/L,
respectively. The study reported that the biomass productivity of C.
pyrenoidosa improved from 0.14 g/L in defined fog’s medium to 1.40
g/L in modified fog’s medium resulting 10 fold increase. The
biochemical composition biosynthesis of C. pyrenoidosa was altered
using nitrogen limiting stress bringing about 5.23 fold increase in
lipid content than control (cell without stress), as analyzed by FTIR
integration method.