Abstract: The purpose of this project is to propose a quick and
environmentally friendly alternative to measure the quality of oils
used in food industry. There is evidence that repeated and
indiscriminate use of oils in food processing cause physicochemical
changes with formation of potentially toxic compounds that can
affect the health of consumers and cause organoleptic changes. In
order to assess the quality of oils, non-destructive optical techniques
such as Interferometry offer a rapid alternative to the use of reagents,
using only the interaction of light on the oil. Through this project, we
used interferograms of samples of oil placed under different heating
conditions to establish the changes in their quality. These
interferograms were obtained by means of a Mach-Zehnder
Interferometer using a beam of light from a HeNe laser of 10mW at
632.8nm. Each interferogram was captured, analyzed and measured
full width at half-maximum (FWHM) using the software from
Amcap and ImageJ. The total of FWHMs was organized in three
groups. It was observed that the average obtained from each of the
FWHMs of group A shows a behavior that is almost linear, therefore
it is probable that the exposure time is not relevant when the oil is
kept under constant temperature. Group B exhibits a slight
exponential model when temperature raises between 373 K and 393
K. Results of the t-Student show a probability of 95% (0.05) of the
existence of variation in the molecular composition of both samples.
Furthermore, we found a correlation between the Iodine Indexes
(Physicochemical Analysis) and the Interferograms (Optical
Analysis) of group C. Based on these results, this project highlights
the importance of the quality of the oils used in food industry and
shows how Interferometry can be a useful tool for this purpose.
Abstract: In order to study the effect of different levels of triple
super phosphate chemical fertilizer and biological phosphate fertilizer
(fertile 2) on some morphological traits of corn this research was
carried out in Ahvaz in 2002 as a factorial experiment in randomized
complete block design with 4 replications). The experiment included
two factors: first, biological phosphate fertilizer (fertile 2) at three
levels of 0, 100, 200 g/ha; second, triple super phosphate chemical
fertilizer at three levels of 0, 60, 90 kg/ha of pure phosphorus (P2O5).
The obtained results indicated that fertilizer treatments had a
significant effect on some morphological traits at 1% probability
level. In this regard, P2B2 treatment (100 g/ha biological phosphate
fertilizer (fertile 2) and 60 kg/ha triple super phosphate fertilizer) had
the greatest plant height, stem diameter, number of leaves and ear
length. It seems that in Ahvaz weather conditions, decrease of
consumption of triple superphosphate chemical fertilizer to less than
a half along with the consumption of biological phosphate fertilizer
(fertile 2) is highly important in order to achieve optimal results.
Therefore, it can be concluded that biological fertilizers can be used
as a suitable substitute for some of the chemical fertilizers in
sustainable agricultural systems.
Abstract: Cross-linked konjac glucomannan and kappa
carrageenan film were prepared by chemical crosslinking using
glutaraldehyde (GA) as the crosslinking agent. The effect
crosslinking on the swelling degree was investigated. Konjac
glucomannan and its mixture with kappa carrageenan film was
immersed in GA solution and then thermally cured. The obtained
cross-linked film was washed and soaked in the ethanol to remove
the unreacted GA. The obtained film was air dried at room
temperature to a constant weight. The infrared spectra and the value
of swelling degree of obtained crosslinked film showed that
glucomannan and kappa carrageenan was able to be cross-linked
using glutaraldehyde by film immersion and curing method without
catalyst. The cross-linked films were found to be pH sensitive,
indicating a potential to be used in drug delivery polymer system.
Abstract: Crops diversity and maintaining and enhancing the
fertility of agricultural lands are basic principles of organic farming.
With a wider range of crops in agroecosystem can improve the ability
to control weeds, pests and diseases, and the performance of crops
rotation and food safety. In this sense, the main objective of the
research was to study the productivity and chemical composition of
some alternative crops and their adaptability to soil and climatic
conditions of the agricultural area in Southern Romania and to
cultivation in the organic farming system. The alternative crops were:
lentil (7 genotypes); five species of grain legumes (5 genotypes); four
species of oil crops (5 genotypes). The seed production was, on
average: 1343 kg/ha of lentil; 2500 kg/ha of field beans; 2400 kg/ha
of chick peas and blackeyed peas; more than 2000 kg/ha of atzuki
beans, over 1250 kg/ha of fenugreek; 2200 kg/ha of safflower; 570
kg/ha of oil pumpkin; 2150 kg/ha of oil flax; 1518 kg/ha of camelina.
Regarding chemical composition, lentil seeds contained: 22.18%
proteins, 3.03% lipids, 33.29% glucides, 4.00% minerals, and 259.97
kcal energy values. For field beans: 21.50% proteins, 4.40% lipids,
63.90% glucides, 5.85% minerals, 395.36 kcal energetic value. For
chick peas: 21.23% proteins, 4.55% lipids, 53.00% glucides, 3.67%
minerals, 348.22 kcal energetic value. For blackeyed peas: 23.30%
proteins, 2.10% lipids, 68.10% glucides, 3.93% minerals, 350.14 kcal
energetic value. For adzuki beans: 21.90% proteins, 2.60% lipids,
69.30% glucides, 4.10% minerals, 402.48 kcal energetic value. For
fenugreek: 21.30% proteins, 4.65% lipids, 63.83% glucides, 5.69%
minerals, 396.54 kcal energetic value. For safflower: 12.60%
proteins, 28.37% lipids, 46.41% glucides, 3.60% minerals, 505.78
kcal energetic value. For camelina: 20.29% proteins, 31.68% lipids,
36.28% glucides, 4.29% minerals, 526.63 kcal energetic value. For
oil pumpkin: 29.50% proteins, 36.92% lipids, 18.50% glucides,
5.41% minerals, 540.15 kcal energetic value. For oil flax: 22.56%
proteins, 34.10% lipids, 27.73% glucides, 5.25% minerals, 558.45
kcal energetic value.
Abstract: Polyaniline is an indispensible component in lightemitting
devices (LEDs), televisions, cellular telephones, automotive,
corrosion-resistant coatings, actuators etc. The electrical conductivity
properties was found be increased by introduction of metal nano
particles. In the present study, an attempt has been made to utilize
platinum nano particles to achieve the improved electrical properties.
Polyaniline and Pt-polyaniline composite are synthesized by
electrochemical routes. X-ray diffractometer confirms the amorphous
nature of polyaniline. The Bragg’s diffraction peaks correspond to
platinum nanoparticles in Pt-polyaniline composite and
thermogravimetric analyzer indicates its decomposition at certain
temperature. The Scanning Electron Micrographs of colloidal
platinum nanoparticles were spherical, uniform shape in the
composite. The current-voltage (I-V) characteristics of the PANI and
composites were also studied which indicate a significant decreasing
resistivity than PANI-Platinum after introduction of pt nanoparticles
in the matrix of polyaniline (PANI).
Abstract: Transparent nickel doped cobalt sulfide was fabricated
on a SnO2:F electrode and tested as an efficient electrocatalyst and as
an alternative to the expensive platinum counter electrode. In order to
investigate how this electrode could affect the electrical
characteristics of a dye-sensitized solar cell, we manufactured cells
with the same TiO2 photoanode sensitized with dye (N719) and
employing the same quasi-solid electrolyte, altering only the counter
electrode used. The cells were electrically and electrochemically
characterized and it was observed that the ones with the Ni doped
CoS2 outperformed the efficiency of the cells with the Pt counter
electrode (3.76% and 3.44% respectively). Particularly, the higher
efficiency of the cells with the Ni doped CoS2 counter electrode (CE)
is mainly because of the enhanced photocurrent density which is
attributed to the enhanced electrocatalytic ability of the CE and the
low charge transfer resistance at the CE/electrolyte interface.
Abstract: The quantitative study of cell mechanics is of
paramount interest, since it regulates the behaviour of the living cells
in response to the myriad of extracellular and intracellular
mechanical stimuli. The novel experimental techniques together with
robust computational approaches have given rise to new theories and
models, which describe cell mechanics as combination of
biomechanical and biochemical processes. This review paper
encapsulates the existing continuum-based computational approaches
that have been developed for interpreting the mechanical responses of
living cells under different loading and boundary conditions. The
salient features and drawbacks of each model are discussed from both
structural and biological points of view. This discussion can
contribute to the development of even more precise and realistic
computational models of cell mechanics based on continuum
approaches or on their combination with microstructural approaches,
which in turn may provide a better understanding of
mechanotransduction in living cells.
Abstract: The effects of flame-holder position, the ratio of flame
holder diameter to combustion chamber diameter and injection angle
on fuel propulsive droplets sizing and effective mass fraction have
been studied by a cold flow. We named the mass of fuel vapor inside
the flammability limit as the effective mass fraction. An empty
cylinder as well as a flame-holder which are a simulator for duct
combustion has been considered. The airflow comes into the cylinder
from one side and injection operation will be done by four nozzles
which are located on the entrance of cylinder. To fulfill the
calculations a modified version of KIVA-3V code which is a
transient, three-dimensional, multiphase, multi component code for
the analysis of chemically reacting flows with sprays, is used.
Abstract: Distillery spentwash contains high chemical oxygen
demand (COD), biological oxygen demand (BOD), color, total
dissolved solids (TDS) and other contaminants even after biological
treatment. The effluent can’t be discharged as such in the surface
water bodies or land without further treatment. Reverse osmosis (RO)
treatment plants have been installed in many of the distilleries at
tertiary level in many of the distilleries in India, but are not properly
working due to fouling problem which is caused by the presence of
high concentration of organic matter and other contaminants in
biologically treated spentwash. In order to make the membrane
treatment a proven and reliable technology, proper pre-treatment is
mandatory. In the present study, ultra-filtration (UF) for pretreatment
of RO at tertiary stage has been performed. Operating
parameters namely initial pH (pHo: 2–10), trans-membrane pressure
(TMP: 4-20 bars) and temperature (T: 15-43°C) were used for
conducting experiments with UF system. Experiments were
optimized at different operating parameters in terms of COD, color,
TDS and TOC removal by using response surface methodology
(RSM) with central composite design. The results showed that
removal of COD, color and TDS was 62%, 93.5% and 75.5%
respectively, with UF, at optimized conditions with increased
permeate flux from 17.5 l/m2/h (RO) to 38 l/m2/h (UF-RO). The
performance of the RO system was greatly improved both in term of
pollutant removal as well as water recovery.
Abstract: The goal of this experiment is to evaluate the
effectiveness of different leachate pre-treatment options in terms of
COD and ammonia removal. This research focused on the evaluation
of physical-chemical methods for pre-treatment of leachate that
would be effective and rapid in order to satisfy the requirements of
the sewer discharge by-laws. The four pre-treatment options
evaluated were: air stripping, chemical coagulation, electrocoagulation
and advanced oxidation with sodium ferrate. Chemical
coagulation reported the best COD removal rate at 43%, compared to
18% for both air stripping and electro-coagulation, and 20% for
oxidation with sodium ferrate. On the other hand, air stripping was
far superior to the other treatment options in terms of ammonia
removal with 86%. Oxidation with sodium ferrate reached only 16%,
while chemical coagulation and electro-coagulation removed less
than 10%. When combined, air stripping and chemical coagulation
removed up to 50% COD and 85% ammonia.
Abstract: Acoustic properties of polymeric liquids are high
sensitive to free gas traces in the form of fine bubbles. Their presence
is typical for such liquids because of chemical reactions, small
wettability of solid boundaries, trapping of air in technological
operations, etc. Liquid temperature influences essentially its
rheological properties, which may have an impact on the bubble
pulsations and sound propagation in the system. The target of the
paper is modeling of the liquid temperature effect on single bubble
dynamics and sound dispersion and attenuation in polymeric solution
with spherical gas bubbles. The basic sources of attenuation (heat
exchange between gas in microbubbles and surrounding liquid,
rheological and acoustic losses) are taken into account. It is supposed
that in the studied temperature range the interface mass transfer has a
minor effect on bubble dynamics. The results of the study indicate
that temperature raise yields enhancement of bubble pulsations and
increase in sound attenuation in the near-resonance range and may
have a strong impact on sound dispersion in the liquid-bubble
mixture at frequencies close to the resonance frequency of bubbles.
Abstract: Zn alloy and composite coatings are widely used in
buildings and structures, automobile and fasteners industries to
protect steel component from corrosion. In this paper, Zn-Ni-Al2O3
nanocomposite coatings were electrodeposited on mild steel using a
novel sol enhanced electroplating method. In this method, transparent
Al2O3 sol was added into the acidic Zn-Ni bath to produced Zn-Ni-
Al2O3 nanocomposite coatings. The effect of alumina sol on the
electrodeposition process, and coating properties was investigated
using cyclic voltammetry, XRD, ESEM and Tafel test. Results from
XRD tests showed that the structure of all coatings was single γ-
Ni5Zn21 phase. Cyclic voltammetry results showed that the
electrodeposition overpotential was lower in the presence of alumina
sol in the bath, and caused the reduction potential of Zn-Ni to shift to
more positive values. Zn-Ni-Al2O3 nanocomposite coatings produced
more uniform and compact deposits, with fine grained microstructure
when compared to Zn-Ni coatings. The corrosion resistance of Zn-Ni
coatings was improved significantly by incorporation of alumina
nanoparticles into the coatings.
Abstract: Sodium formate is the chemical substance used for
food additive. Catalase is the important antioxidative enzyme in
protecting the cell from oxidative damage by reactive oxygen species
(ROS). The resultant level of oxidative stress in sodium formatetreated
lymphocytes was investigated. The sodium formate
concentrations of 0.05, 0.1, 0.2, 0.4 and 0.6 mg/mL were treated in
human lymphocytes for 12 hours. After 12 treated hours, catalase
activity change was measured in sodium formate-treated
lymphocytes. The results showed that the sodium formate
concentrations of 0.4 and 0.6 mg/mL significantly decreased catalase
activities in lymphocytes (P < 0.05). The change of catalase activity
in sodium formate-treated lymphocytes may be the oxidative damage
marker for detect sodium formate exposure in human.
Abstract: This paper presents results of compressive strength,
capillary water absorption, and density tests conducted on concrete
containing recycled aggregate (RCA) which is obtained from
structural waste generated by the construction industry in Turkey. In
the experiments, 0%, 15%, 30%, 45% and 60% of the normal
(natural) coarse aggregate was replaced by the recycled aggregate.
Maximum aggregate particle sizes were selected as 16 mm, 22,4 mm
and 31,5 mm; and 0,06%, 0,13% and 0,20% of air-entraining agent
(AEA) were used in mixtures. Fly ash and superplasticizer were used
as a mineral and chemical admixture, respectively. The same type
(CEM I 42.5) and constant dosage of cement were used in the study.
Water/cement ratio was kept constant as 0.53 for all mixture. It was
concluded that capillary water absorption, compressive strength, and
density of concrete decreased with increasing RCA ratio. Increasing
in maximum aggregate particle size and amount of AEA also affect
the properties of concrete significantly.
Abstract: Due to the resultant leachate from waste
decomposition in landfills has polluter potential hundred times
greater than domestic sewage, this is considered a problem related to
the depreciation of environment requiring pre-disposal treatment.In
seeking to improve this situation, this project proposes the treatment
of landfill leachate using natural fibers intercropped with advanced
oxidation processes. The selected natural fibers were palm, coconut
and banana fiber.These materials give sustainability to the project
because, besides having adsorbent capacity, are often part of waste
discarded. The study was conducted in laboratory scale.In trials, the
effluents were characterized as Chemical Oxygen Demand (COD),
Turbidity and Color. The results indicate that is technically
promising since that there were extremely oxidative conditions, the
use of certain natural fibers in the reduction of pollutants in leachate
have been obtained results of COD removals between 67.9% and
90.9%, Turbidity between 88.0% and 99.7% and Color between
67.4% and 90.4%.The expectation generated is to continue evaluating
the association of efficiency of other natural fibers with other landfill
leachate treatment processes.
Abstract: A comparison of activity and stability of the as-formed
Pt/C, Pt-Co and Pt-Pd/C electrocatalysts, prepared by a combined
approach of impregnation and seeding, was performed. According to
the activity test in a single Proton Exchange Membrane (PEM) fuel
cell, the Oxygen Reduction Reaction (ORR) activity of the Pt-M/C
electrocatalyst was slightly lower than that of Pt/C. The j0.9 V and
E10 mA/cm2 of the as-prepared electrocatalysts increased in the order of
Pt/C > Pt-Co/C > Pt-Pd/C. However, in the medium-to-high current
density region, Pt-Pd/C exhibited the best performance. With regard to
their stability in a 0.5 M H2SO4 electrolyte solution, the
electrochemical surface area decreased as the number of rounds of
repetitive potential cycling increased due to the dissolution of the
metals within the catalyst structure. For long-term measurement, Pt-
Pd/C was the most stable than the other three electrocatalysts.
Abstract: This work studies the effect of chemical composition
on the activity and selectivity of γ–alumina supported CuO/
MnO2/Cr2O3 catalysts toward deep oxidation of CO, dimethyl ether
(DME) and methanol. The catalysts were prepared by impregnation
of the support with an aqueous solution of copper nitrate, manganese
nitrate and CrO3 under different conditions. Thermal, XRD and TPR
analysis were performed. The catalytic measurements of single
compounds oxidation were carried out on continuous flow equipment
with a four-channel isothermal stainless steel reactor. Flow-line
equipment with an adiabatic reactor for simultaneous oxidation of all
compounds under the conditions that mimic closely the industrial
ones was used. The reactant and product gases were analyzed by
means of on-line gas chromatographs.
On the basis of XRD analysis it can be concluded that the active
component of the mixed Cu-Mn-Cr/γ–alumina catalysts consists of at
least six compounds – CuO, Cr2O3, MnO2, Cu1.5Mn1.5O4,
Cu1.5Cr1.5O4 and CuCr2O4, depending on the Cu/Mn/Cr molar ratio.
Chemical composition strongly influences catalytic properties, this
influence being quite variable with regards to the different processes.
The rate of CO oxidation rapidly decrease with increasing of
chromium content in the active component while for the DME was
observed the reverse trend. It was concluded that the best
compromise are the catalysts with Cu/(Mn + Cr) molar ratio 1:5 and
Mn/Cr molar ratio from 1:3 to 1:4.
Abstract: In this work new macroporous Ni electrodes modified
with Au nanoparticles for hydrogen production have been developed.
The supporting macroporous Ni electrodes have been obtained by
means of the electrodeposition at high current densities. Then, the Au
nanoparticles were synthesized and added to the electrode surface.
The electrocatalytic behaviour of the developed electrocatalysts was
studied by means of pseudo-steady-state polarization curves,
electrochemical impedance spectroscopy (EIS) and hydrogen
discharge curves. The size of the Au synthetized nanoparticles shows
a monomodal distribution, with a very sharp band between 10 and 50
nm. The characteristic parameters d10, d50 and d90 were 14, 20 and
31 nm respectively. From Tafel polarization data has been concluded
that the Au nanoparticles improve the catalytic activity of the
developed electrodes towards the HER respect to the macroporous Ni
electrodes. EIS permits to obtain the electrochemically active area by
means of the roughness factor value. All the developed electrodes
show roughness factor values in the same order of magnitude. From
the activation energy results it can be concluded that the Au
nanoparticles improve the intrinsic catalytic activity of the
macroporous Ni electrodes.
Abstract: Mobil Producing Nigeria Unlimited (MPNU), a
subsidiary of ExxonMobil and the highest crude oil & condensate
producer in Nigeria has its operational base and an oil terminal, the
Qua Iboe terminal (QIT) located at Ibeno, Nigeria. Other oil
companies like Network Exploration and Production Nigeria Ltd,
Frontier Oil Ltd; Shell Petroleum Development Company Ltd; Elf
Petroleum Nigeria Ltd and Nigerian Agip Energy, a subsidiary of the
Italian ENI E&P operate onshore, on the continental shelf and in deep
offshore of the Atlantic Ocean, respectively with the coastal waters of
Ibeno, Nigeria as the nearest shoreline. This study was designed to
delineate the oil-polluted sites in Ibeno, Nigeria using
microbiological and physico-chemical characterization of soils,
sediments and ground and surface water samples from the study area.
Results obtained revealed that there have been significant recent
hydrocarbon inputs into this environment as observed from the high
counts of hydrocarbonoclastic microorganisms in excess of 1% at all
the stations sampled. Moreover, high concentrations of THC, BTEX
and heavy metals contents in all the samples analyzed corroborate the
high recent crude oil input into the study area. The results also
showed that the pollution of the different environmental media
sampled were of varying degrees, following the trend: ground water
> surface water > sediments > soils.
Abstract: Rice bran is normally used as a raw material for rice
bran oil production or sold as feed with a low price. Conventionally,
the protein in defatted rice bran was extracted using alkaline
extraction and acid precipitation, which involves in chemical usage
and lowering some nutritious component. This study was conducted
in order to extract of rice bran protein concentrate (RBPC) from
defatted rice bran using enzymes and employing polysaccharides in a
precipitating step. The properties of RBPC obtained will be compared
to those of a control sample extracted using a conventional method.
The results showed that extraction of protein from rice bran using
enzymes exhibited the higher protein recovery compared to that
extraction with alkaline. The extraction conditions using alcalase 2%
(v/w) at 50 C, pH 9.5 gave the highest protein (2.44%) and yield
(32.09%) in extracted solution compared to other enzymes. Rice bran
protein concentrate powder prepared by a precipitation step using
alginate (protein in solution: alginate 1:0.016) exhibited the highest
protein (27.55%) and yield (6.84%). Precipitation using alginate was
better than that of acid. RBPC extracted with alkaline (ALK) or
enzyme alcalase (ALC), then precipitated with alginate (AL)
(samples RBP-ALK-AL and RBP-ALC-AL) yielded the precipitation
rate of 75% and 91.30%, respectively. Therefore, protein
precipitation using alginate was then selected. Amino acid profile of
control sample, and sample precipitated with alginate, as compared to
casein and soy protein isolated, showed that control sample showed
the highest content among all sample. Functional property study of
RBP showed that the highest nitrogen solubility occurred in pH 8-10.
There was no statically significant between emulsion capacity and
emulsion stability of control and sample precipitated by alginate.
However, control sample showed a higher of foaming capacity and
foaming stability compared to those of sample precipitated with
alginate. The finding was successful in terms of minimizing
chemicals used in extraction and precipitation steps in preparation of
rice bran protein concentrate. This research involves in a production
of value-added product in which the double amount of protein (28%)
compared to original amount (14%) contained in rice bran could be
beneficial in terms of adding to food products e.g. healthy drink with
high protein and fiber. In addition, the basic knowledge of functional
property of rice bran protein concentrate was obtained, which can be
used to appropriately select the application of this value-added
product from rice bran.