Abstract: Geometric and mechanical properties all influence the
resistance of RC structures and may, in certain combination of
property values, increase the risk of a brittle failure of the whole
system.
This paper presents a statistical and probabilistic investigation on
the resistance of RC beams designed according to Eurocodes 2 and 8,
and subjected to multiple failure modes, under both the natural
variation of material properties and the uncertainty associated with
cross-section and transverse reinforcement geometry. A full
probabilistic model based on JCSS Probabilistic Model Code is
derived. Different beams are studied through material nonlinear
analysis via Monte Carlo simulations. The resistance model is
consistent with Eurocode 2. Both a multivariate statistical evaluation
and the data clustering analysis of outcomes are then performed.
Results show that the ultimate load behaviour of RC beams
subjected to flexural and shear failure modes seems to be mainly
influenced by the combination of the mechanical properties of both
longitudinal reinforcement and stirrups, and the tensile strength of
concrete, of which the latter appears to affect the overall response of
the system in a nonlinear way. The model uncertainty of the
resistance model used in the analysis plays undoubtedly an important
role in interpreting results.
Abstract: The main aim of this article is to present a balance of the decade of Polish air transport market in the European Union having taking into account selected entities of the aviation market. This article analyzes the functioning of the Polish air transport market after the Polish accession to the European Union. During the study two main areas were pointed: shipping activity and activity of the airports. The most important benefits of integration and the benefits of introducing of the open sky policy were indicated. The last part of the article presents the perspectives of development of air traffic.
Abstract: The study examined the effect of Bonny Light whole
crude oil (WC) and its water soluble fraction (WSF) on the activities
of antioxidant enzymes (catalase (CAT) and superoxide dismutase
(SOD)) and crude mitochondria ATPases in the radicle of
germinating bean (Vigna unguiculata). The percentage germination,
level of lipid peroxidation, antioxidant enzyme and mitochondria
Ca2+ and Mg2+ ATPase activities were measured in the radicle of
bean after 7, 14 and 21 days post germination. Viable bean seeds
were planted in soils contaminated with 10ml, 25ml and 50ml of
whole crude oil (WC) and its water soluble fraction (WSF) to obtain
2, 5 and 10% v/w crude oil contamination. There was dose dependent
reduction of the number of bean seeds that germinated in the
contaminated soils compared with control (p
Abstract: This study was conducted to investigate the effect of
the antioxidant activity of germinated African Yam Bean (AYB) on
oxidative stress markers in alloxan induced diabetic rat. Rats were
randomized into three groups; control, diabetic and germinated AYB
– treated diabetic rats. The Total phenol and flavonoid content and
DPPH radical scavenging activity before and after germination were
investigated. The glucose level, lipid peroxidation and reduced
glutathione of the animals were also determined using standard
technique for four weeks. Germination increased the total phenol,
flavonoid and antioxidant activity of AYB extract by 19.14%,
32.28% and 57.25% respectively. The diabetic rats placed on
germinated AYB diet had a significant decrease in the blood glucose
and lipid peroxidation with a corresponding increase in glutathione
(p
Abstract: Thin ZnO films are deposited on glass substrates via
sol–gel method and dip-coating. The films are prepared from zinc
acetate dehydrate as a starting reagent. After that the as-prepared
ZnO sol is aged for different periods (0, 1, 3, 5, 10, 15 and 30 days).
Nanocrystalline thin films are deposited from various sols. The
effect ZnO sols aging time on the structural and photocatalytic
properties of the films is studied. The films surface is studied by
Scanning Electron Microscopy. The effect of the aging time of the
starting solution is studied in the photocatalytic degradation of
Reactive Black 5 (RB5) by UV-vis spectroscopy. The experiments
are conducted upon UV-light illumination and in complete darkness.
The variation of the absorption spectra shows the degradation of RB5
dissolved in water, as a result of the reaction, occurring on the surface
of the films and promoted by UV irradiation. The initial
concentrations of dye (5, 10 and 20 ppm) and the effect of the aging
time are varied during the experiments. The results show, that the
increasing aging time of starting solution with respect to ZnO
generally promotes photocatalytic activity. The thin films obtained
from ZnO sol, which is aged 30 days have best photocatalytic
degradation of the dye (97,22%) in comparison with the freshly
prepared ones (65,92%). The samples and photocatalytic
experimental results are reproducible. Nevertheless, all films exhibit
a substantial activity in both UV light and darkness, which is
promising for the development of new ZnO photocatalysts by sol-gel
method.
Abstract: The concept of urban transformation came about
through interventions aimed at bringing socially and economically
problematic areas of cities into use. The issue of urban transformation
arose frequently during the post-2000 period in particular, and legal
regulations on this matter were also developed in Turkey. Urban
transformation project would be a focal point for the formation of the
city in the near future. Izmir, which is third largest city of Turkey, is
an important trade and port city. But, assessment of the current
situation shows that, the majority of existing residential areas was
formed with squatters and unplanned settlements in Izmir city center.
Therefore an important part of these areas have significant problems
in terms of the quality of life, safety and environmental quality. In
this study, the central policies in Turkey and local policies in Đzmir
about urban transformation will be considered. In addition, urban
renewal projects that are being implemented in Izmir were discussed
and suggestions will be developed in accordance with this policy.
Abstract: Urban areas have been expanded throughout the
globe. Monitoring and modelling urban growth have become a
necessity for a sustainable urban planning and decision making.
Urban prediction models are important tools for analyzing the causes
and consequences of urban land use dynamics. The objective of this
research paper is to analyze and model the urban change, which has
been occurred from 1990 to 2000 using CORINE land cover maps.
The model was developed using drivers of urban changes (such as
road distance, slope, etc.) under an Artificial Neural Network
modelling approach. Validation was achieved using a prediction map
for 2006 which was compared with a real map of Urban Atlas of
2006. The accuracy produced a Kappa index of agreement of 0,639
and a value of Cramer's V of 0,648. These encouraging results
indicate the importance of the developed urban growth prediction
model which using a set of available common biophysical drivers
could serve as a management tool for the assessment of urban
change.
Abstract: Analyzing DNA microarray data sets is a great
challenge, which faces the bioinformaticians due to the complication
of using statistical and machine learning techniques. The challenge
will be doubled if the microarray data sets contain missing data,
which happens regularly because these techniques cannot deal with
missing data. One of the most important data analysis process on
the microarray data set is feature selection. This process finds the
most important genes that affect certain disease. In this paper, we
introduce a technique for imputing the missing data in microarray
data sets while performing feature selection.
Abstract: Currently, there is excessively growing information
about places on Facebook, which is the largest social network but
such information is not explicitly organized and ranked. Therefore
users cannot exploit such data to recommend places conveniently and
quickly. This paper proposes a Facebook application and an Android
application that recommend places based on the number of check-ins
of those places, the distance of those places from the current location,
the number of people who like Facebook page of those places, and
the number of talking about of those places. Related Facebook data is
gathered via Facebook API requests. The experimental results of the
developed applications show that the applications can recommend
places and rank interesting places from the most to the least. We have
found that the average satisfied score of the proposed Facebook
application is 4.8 out of 5. The users’ satisfaction can increase by
adding the app features that support personalization in terms of
interests and preferences.
Abstract: Stator elements «Vane diffuser + crossover + return
channel» of stages with different specific speed were investigated by
CFD calculations. The regime parameter was introduced to present
efficiency and loss coefficient performance of all elements together.
Flow structure demonstrated advantages and disadvantages of design.
Flow separation in crossovers was eliminated by its shape
modification. Efficiency increased visibly. Calculated CFD
performances are in acceptable correlation with predicted ones by
engineering design method. The information obtained is useful for
design method better calibration.
Abstract: This study carried out comparative seismic
performance of reinforced concrete frames infilled by masonry walls
with different heights. Partial and fully infilled reinforced concrete
frames were modeled for the research objectives and the analysis
model for a bare reinforced concrete frame was also established for
comparison. Non–linear static analyses for the studied frames were
performed to investigate their structural behavior under extreme
seismic loads and to find out their collapse mechanism. It was
observed from analysis results that the strengths of the partial infilled
reinforced concrete frames are increased and their ductilities are
reduced, as infilled masonry walls are higher. Especially, reinforced
concrete frames with higher partial infilled masonry walls would
experience shear failures. Non–linear dynamic analyses using 10
earthquake records show that the bare and fully infilled reinforced
concrete frame present stable collapse mechanism while the reinforced
concrete frames with partially infilled masonry walls collapse in more
brittle manner due to short-column effects.
Abstract: Waste silicon carbide (waste SiC) filled high-density
polyethylene (HDPE) with and without surface modifiers were
studied. Two types of surface modifiers namely; high-density
polyethylene-grafted-maleic anhydride (HDPE-g-MA) and 3-aminopropyltriethoxysilane have been used in this study. The
composites were produced using a two roll mill, extruder and shaped
in a hydraulic compression molding machine. The mechanical
properties of polymer composites such as flexural strength and
modulus, impact strength, tensile strength, stiffness and hardness
were investigated over a range of compositions. It was found that,
flexural strength and modulus, tensile modulus and hardness
increased, whereas impact strength and tensile strength decreased
with the increasing in filler contents, compared to the neat HDPE. At
similar filler content, the effect of both surface modifiers increased
flexural modulus, impact strength, tensile strength and stiffness but
reduced the flexural strength. Morphological investigation using
SEM revealed that the improvement in mechanical properties was
due to enhancement of the interfacial adhesion between waste SiC
and HDPE.
Abstract: A knowledge-based expert system with the acronym
RASPE is developed as an application tool to help decision makers in
construction companies make informed decisions about managing
risks in pipeline construction projects. Choosing to use expert
systems from all available artificial intelligence techniques is due to
the fact that an expert system is more suited to representing a
domain’s knowledge and the reasoning behind domain-specific
decisions. The knowledge-based expert system can capture the
knowledge in the form of conditional rules which represent various
project scenarios and potential risk mitigation/response actions. The
built knowledge in RASPE is utilized through the underlying
inference engine that allows the firing of rules relevant to a project
scenario into consideration. Paper provides an overview of the
knowledge acquisition process and goes about describing the
knowledge structure which is divided up into four major modules.
The paper shows one module in full detail for illustration purposes
and concludes with insightful remarks.
Abstract: Modelling of the earth's surface and evaluation of
urban environment, with 3D models, is an important research topic.
New stereo capabilities of high resolution optical satellites images,
such as the tri-stereo mode of Pleiades, combined with new image
matching algorithms, are now available and can be applied in urban
area analysis. In addition, photogrammetry software packages gained
new, more efficient matching algorithms, such as SGM, as well as
improved filters to deal with shadow areas, can achieve more dense
and more precise results.
This paper describes a comparison between 3D data extracted
from tri-stereo and dual stereo satellite images, combined with pixel
based matching and Wallis filter. The aim was to improve the
accuracy of 3D models especially in urban areas, in order to assess if
satellite images are appropriate for a rapid evaluation of urban
environments.
The results showed that 3D models achieved by Pleiades tri-stereo
outperformed, both in terms of accuracy and detail, the result
obtained from a Geo-eye pair. The assessment was made with
reference digital surface models derived from high resolution aerial
photography. This could mean that tri-stereo images can be
successfully used for the proposed urban change analyses.
Abstract: In this paper, the effect of grades 32.4 and 42.5
Portland-limestone cements generally used for concrete production in
Nigeria on concrete compressive strength is investigated.
Investigation revealed that the compressive strength of concrete
produced with Portland-limestone cement grade 42.5 is generally
higher than that produced with cement grade 32.5. The percentage
difference between the compressive strengths of the concrete cubes
produced with Portland-limestone cement grades 42.5 and 32.5 is
inversely proportional to the richness of the concrete with the highest
and the least percentage difference associated with the 1:2:4 and
1:1:2 mix ratios respectively. It is recommended that cement grade
42.5 be preferred for construction in Nigeria as this will lead to the
construction of stronger concrete structures, which will reduce the
incidence of failure of building and other concrete structures at no
additional cost since the cost of both cement grades are the same.
Abstract: Solar energy is a good option among renewable
energy resources due to its easy availability and abundance. The
simplest and most efficient way to utilize solar energy is to convert it
into thermal energy and this can be done with the help of solar
collectors. The thermal performance of such collectors is poor due to
less heat transfer from the collector surface to air. In this work,
experimental investigations of single pass solar air heater having
triangular duct and provided with roughness element on the underside
of the absorber plate. V-shaped ribs are used for investigation having
three different values of relative roughness pitch (p/e) ranges from 4-
16 for a fixed value of angle of attack (α), relative roughness height
(e/Dh) and a relative gap distance (d/x) values are 60°, 0.044 and 0.60
respectively. Result shows that considerable augmentation in heat
transfer has been obtained by providing roughness.
Abstract: The dielectric properties and ionic conductivity of
novel "ceramic state" polymer electrolytes for high capacity lithium
battery are characterized by Radio frequency and Microwave
methods in two broad frequency ranges from 50 Hz to 20 KHz and 4
GHz to 40 GHz. This innovative solid polymer electrolyte which is
highly ionic conductive (10-3 S/cm at room temperature) from -40oC
to +150oC can be used in any battery application. Such polymer
exhibits properties more like a ceramic rather than polymer. The
various applied measurement methods produced accurate dielectric
results for comprehensive analysis of electrochemical properties and
ion transportation mechanism of this newly invented polymer
electrolyte. Two techniques and instruments employing air gap
measurement by Capacitance Bridge and in-waveguide measurement
by vector network analyzer are applied to measure the complex
dielectric spectra. The complex dielectric spectra are used to
determine the complex alternating current electrical conductivity and
thus the ionic conductivity.
Abstract: This study was conducted in the area of Vlora Bay,
Albania. Data about Sea Turtles Caretta caretta and Chelonia mydas,
belonging to two periods of time (1984 – 1991; 2008 – 2014) are
given. All data gathered were analyzed using recent methodologies.
For all turtles captured (as by catch), the Curve Carapace Length
(CCL) and Curved Carapace Width (CCW) were measured. These
data were statistically analyzed, where the mean was 67.11 cm for
CCL and 57.57 cm for CCW of all individuals studied (n=13). All
untagged individuals of marine turtles were tagged using metallic
tags (Stockbrand’s titanium tag) with an Albanian address. Sex was
determined and resulted that 45.4% of individuals were females,
27.3% males and 27.3% juveniles. All turtles were studied for the
presence of the epibionts. The area of Vlora Bay is used from marine
turtles (Caretta caretta) as a migratory corridor to pass from
Mediterranean to the northern part of the Adriatic Sea.
Abstract: In this study was monitored the population of the
European Pond Turtle, Emys orbicularis (Linnaeus, 1758) in the area
of Narta Lagoon, Vlora Bay (Albania), from August to October 2014.
A total of 54 individuals of E. orbicularis were studied using
different methodologies. Curved Carapace Length (CCL), Plastron
Length (PL) and Curved Carapace Width (CCW) were measured for
each individual of E. orbicularis and were statistically analyzed. All
captured turtles were separated in seven different size – classes based
on their carapace length (CCL). Each individual of E. orbicularis was
marked by notching the carapace (marginal scutes). Form all
individuals captured resulted that 37 were females (68.5%), 14 males
(25.9%), 3 juveniles (5.5%), while 18 individuals of E. orbicularis
were recaptured for the first and some for the second time.
Abstract: The belief of a heavenly God is enshrined to all
Abrahamic religions which form the three major religions of the
world today. Muslims believe in Allah who is above the seven
heavens. The youth in the United Arab Emirates (UAE) study Islamic
courses as part of their high school curriculum and are required to
take at least one Islamic course at the university level to gain credit
hours towards their general education (GENED). This paper provides
an insight of what the youth studying in the UAE think of where
Allah is. Our analysis shows that a big number of Muslim youth were
not sure, especially those from the Middle Eastern and Arab countries
bringing to conclusion that this subject needs to be revisited again in
the course work.