Abstract: The experimental thermal performance of two heat
exchangers in closed-wet cooling tower (CWCT) was investigated in
this study. The test sections are heat exchangers which have multi path
that is used as the entrance of cooling water and are consisting of
bare-type copper tubes between 15.88mm and 19.05mm. The process
fluids are the cooling water that flows from top part of heat exchanger
to bottom side in the inner side of tube, and spray water that flows
gravitational direction in the outer side of it. Air contacts its outer side
of that as it counterflows. Heat and mass transfer coefficients and
cooling capacity were calculated with variations of process fluids,
multi path and different diameter tubes to figure out the performance
of characteristics of CWCT.
The main results were summarized as follows: The results show this
experiment is reliable with values of heat and mass transfer
coefficients comparing to values of correlations. Heat and mass
transfer coefficients and cooling capacity of two paths are higher than
these with one path using 15.88 and 19.05mm tubes. Cooling capacity
per unit volume with 15.88mm tube using one and two paths are
higher than 19.05mm tube due to increase of surface area per unit
volume.
Abstract: This study investigated the presence of polycyclic
aromatic hydrocarbons (PAHs) in the sediments of the Musa Bay
(around the PETZONE coastal area) from Feb 2010 to Jun 2010.
Concentrations of PAHs recorded in the Musa Bay sediments ranged
from 537.89 to 26,659.06 ng/g dry weight with a mean value of
3990.74 ng/g. the highest concentration of PAHs was observed at
station 4, which is located near the aromatic outlet of Imam
Khomeini petrochemical company (station 4: BI-PC Aromatic
effluent outlet) in which its concentration level was more than the
NOAA sediment quality guideline value (ERL= 4022 ng/g dry
weight). Owing to the concentration of PAHs in the study area, its
concentration level was still meet the NOAA sediment quality
guideline value (ERL: 4022 ng/g dry weight); however, according to
the PELq factor, slightly adverse biological effects are associated
with the exposure to PAHs levels in the study area (0.1< PELq= 0.24
> 0.5).
Abstract: In this article the influence of higher frequency effects
in addition to a special damper design on the electrical behavior of a
synchronous generator main exciter machine is investigated. On the
one hand these machines are often highly stressed by harmonics from
the bridge rectifier thus facing additional eddy current losses. On the
other hand the switching may cause the excitation of dangerous
voltage peaks in resonant circuits formed by the diodes of the
rectifier and the commutation reactance of the machine. Therefore
modern rotating exciters are treated like synchronous generators
usually modeled with a second order equivalent circuit. Hence the
well known Standstill Frequency Response Test (SSFR) method is
applied to a test machine in order to determine parameters for the
simulation. With these results it is clearly shown that higher
frequencies have a strong impact on the conventional equivalent
circuit model. Because of increasing field displacement effects in the
stranded armature winding the sub-transient reactance is even smaller
than the armature leakage at high frequencies. As a matter of fact this
prevents the algorithm to find an equivalent scheme. This issue is
finally solved using Laplace transfer functions fully describing the
transient behavior at the model ports.
Abstract: The purposes of this research were to study the citizen
participation in preventing illegal drugs in one of a poor and small
community of Bangkok, Thailand and to compare the level of
participation and concern of illegal drugs problem by using
demographic variables. This paper drew upon data collected from a
local citizens survey conducted in Bangkok, Thailand during summer
of 2012. A total of 200 respondents were elicited as data input for,
and one way ANOVA test. The findings revealed that the overall
citizen participation was in the level of medium. The mean score
showed that benefit from the program was ranked as the highest and
the decision to participate was ranked as second while the follow-up
of the program was ranked as the lowest.
In terms of the difference in demographic such as gender, age,
level of education, income, and year of residency, the hypothesis
testing’s result disclosed that there were no difference in their level
of participation. However, difference in occupation showed a
difference in their level of participation and concern which was
significant at the 0.05 confidence level.
Abstract: Cosmic showers, from their places of origin in space,
after entering earth generate secondary particles called Extensive Air
Shower (EAS). Detection and analysis of EAS and similar High
Energy Particle Showers involve a plethora of experimental setups
with certain constraints for which soft-computational tools like
Artificial Neural Network (ANN)s can be adopted. The optimality
of ANN classifiers can be enhanced further by the use of Multiple
Classifier System (MCS) and certain data - dimension reduction
techniques. This work describes the performance of certain data
dimension reduction techniques like Principal Component Analysis
(PCA), Independent Component Analysis (ICA) and Self Organizing
Map (SOM) approximators for application with an MCS formed
using Multi Layer Perceptron (MLP), Recurrent Neural Network
(RNN) and Probabilistic Neural Network (PNN). The data inputs are
obtained from an array of detectors placed in a circular arrangement
resembling a practical detector grid which have a higher dimension
and greater correlation among themselves. The PCA, ICA and SOM
blocks reduce the correlation and generate a form suitable for real
time practical applications for prediction of primary energy and
location of EAS from density values captured using detectors in a
circular grid.
Abstract: The fixed partial dentures are mainly used in the frontal
part of the dental arch because of their great esthetics. There are
several factors that are associated with the stress state created in
ceramic restorations, including: thickness of ceramic layers,
mechanical properties of the materials, elastic modulus of the
supporting substrate material, direction, magnitude and frequency of
applied load, size and location of occlusal contact areas, residual
stresses induced by processing or pores, restoration-cement
interfacial defects and environmental defects. The purpose of this
study is to evaluate the capability of Polarization Sensitive Optical
Coherence Tomography (PSOCT) in detection and analysis of
possible material defects in metal-ceramic and integral ceramic fixed
partial dentures. As a conclusion, it is important to have a non
invasive method to investigate fixed partial prostheses before their
insertion in the oral cavity in order to satisfy the high stress
requirements and the esthetic function.
Abstract: This paper reports on the enhanced photoluminescence
(PL) of nanocomposites through the layered structuring of phosphor
and quantum dot (QD). Green phosphor of Sr2SiO4:Eu, red QDs of
CdSe/CdS/CdZnS/ZnS core-multishell, and thermo-curable resin
were used for this study. Two kinds of composite (layered and mixed)
were prepared, and the schemes for optical energy transfer between
QD and phosphor were suggested and investigated based on PL decay
characteristics. It was found that the layered structure is more effective
than the mixed one in the respects of PL intensity, PL decay and
thermal loss. When this layered nanocomposite (QDs on phosphor) is
used to make white light emitting diode (LED), the brightness is
increased by 37 %, and the color rendering index (CRI) value is raised
to 88.4 compared to the mixed case of 80.4.
Abstract: In the present study, the incorporation of graphene
into blends of acrylonitrile-butadiene-styrene terpolymer with
polypropylene (ABS/PP) was investigated focusing on the
improvement of their thermomechanical characteristics and the effect
on their rheological behavior. The blends were prepared by melt
mixing in a twin-screw extruder and were characterized by measuring
the MFI as well as by performing DSC, TGA and mechanical tests.
The addition of graphene to ABS/PP blends tends to increase their
melt viscosity, due to the confinement of polymer chains motion.
Also, graphene causes an increment of the crystallization temperature
(Tc), especially in blends with higher PP content, because of the
reduction of surface energy of PP nucleation, which is a consequence
of the attachment of PP chains to the surface of graphene through the
intermolecular CH-π interaction. Moreover, the above nanofiller
improves the thermal stability of PP and increases the residue of
thermal degradation at all the investigated compositions of blends,
due to the thermal isolation effect and the mass transport barrier
effect. Regarding the mechanical properties, the addition of graphene
improves the elastic modulus, because of its intrinsic mechanical
characteristics and its rigidity, and this effect is particularly strong in
the case of pure PP.
Abstract: This paper presents an integrated model that
automatically measures the change of rivers, damage area of bridge
surroundings, and change of vegetation. The proposed model is on the
basis of a neurofuzzy mechanism enhanced by SOM optimization
algorithm, and also includes three functions to deal with river imagery.
High resolution imagery from FORMOSAT-2 satellite taken before
and after the invasion period is adopted. By randomly selecting a
bridge out of 129 destroyed bridges, the recognition results show that
the average width has increased 66%. The ruined segment of the
bridge is located exactly at the most scour region. The vegetation
coverage has also reduced to nearly 90% of the original. The results
yielded from the proposed model demonstrate a pinpoint accuracy rate
at 99.94%. This study brings up a successful tool not only for
large-scale damage assessment but for precise measurement to
disasters.
Abstract: This research aimed to modify pineapple leaf paper
(PALP) for using as wet media in the evaporation cooling system by
improving wet mechanical property (tensile strength) without
compromising water absorption property. Polyamideamineepichorohydrin
resin (PAE) and carboxymethylcellulose (CMC)
were used to strengthen the paper, and the PAE and CMC ratio of
80:20 showed the optimum wet and dry tensile index values, which
were higher than those of the commercial cooling pad (CCP).
Compared with CCP, PALP itself and all the PAE/CMC modified
PALP possessed better water absorption. The PAE/CMC modified
PALP had potential to become a new type of wet media.
Abstract: This paper presents a new method for estimating the mean curve of impulse voltage waveforms that are recorded during impulse tests. In practice, these waveforms are distorted by noise, oscillations and overshoot. The problem is formulated as an estimation problem. Estimation of the current signal parameters is achieved using a fast and accurate technique. The method is based on discrete dynamic filtering algorithm (DDF). The main advantage of the proposed technique is its ability in producing the estimates in a very short time and at a very high degree of accuracy. The algorithm uses sets of digital samples of the recorded impulse waveform. The proposed technique has been tested using simulated data of practical waveforms. Effects of number of samples and data window size are studied. Results are reported and discussed.
Abstract: Human genome is not only the evolutionary
summation of all advantageous events, but also houses lesions of
deleterious foot prints. A single gene mutation sometimes may
express multiple consequences in numerous tissues and a linear
relationship of the genotype and the phenotype may often be obscure.
ß Thalassemia minor, a transfusion independent mild anaemia,
coupled with environment among other factors may articulate into
phenotypic pleotropy with Hypocholesterolemia, Vitamin D
deficiency, Tissue hypoxia, Hyper-parathyroidism and Psychological
alterations. Occurrence of Pancreatic insufficiency, resultant
steatorrhoea, Vitamin-D (25-OH) deficiency (13.86 ngm/ml) with
Hypocholesterolemia (85mg/dl) in a 30 years old male ß Thal-minor
patient (Hemoglobin 11mg/dl with Fetal Hemoglobin 2.10%, Hb A2
4.60% and Hb Adult 84.80% and altered Hemogram) with increased
Para thyroid hormone (62 pg/ml) & moderate Serum Ca+2
(9.5mg/ml) indicate towards a cascade of phenotypic pleotropy
where the ß Thalassemia mutation ,be it in the 5’ cap site of the
mRNA , differential splicing etc in heterozygous state is effecting
several metabolic pathways. Compensatory extramedulary
hematopoiesis may not coped up well with the stressful life style of
the young individual and increased erythropoietic stress with high
demand for cholesterol for RBC membrane synthesis may have
resulted in Hypocholesterolemia.Oxidative stress and tissue hypoxia
may have caused the pancreatic insufficiency, leading to Vitamin D
deficiency. This may in turn have caused the secondary
hyperparathyroidism to sustain serum Calcium level. Irritability and
stress intolerance of the patient was a cumulative effect of the vicious
cycle of metabolic compromises. From these findings we propose
that the metabolic deficiencies in the ß Thalassemia mutations may
be considered as the phenotypic display of the pleotropy to explain
the genetic epidemiology.
According to the recommendations from the NIH Workshop on
Gene-Environment Interplay in Common Complex Diseases: Forging
an Integrative Model, study design of observations should be
informed by gene-environment hypotheses and results of a study
(genetic diseases) should be published to inform future hypotheses.
Variety of approaches is needed to capture data on all possible
aspects, each of which is likely to contribute to the etiology of
disease. Speakers also agreed that there is a need for development of
new statistical methods and measurement tools to appraise
information that may be missed out by conventional method where
large sample size is needed to segregate considerable effect.
A meta analytic cohort study in future may bring about significant
insight on to the title comment.
Abstract: This paper aims to study decomposition behavior in
pyrolytic environment of four lignocellulosic biomass (oil palm shell,
oil palm frond, rice husk and paddy straw), and two commercial
components of biomass (pure cellulose and lignin), performed in a
thermogravimetry analyzer (TGA). The unit which consists of a
microbalance and a furnace flowed with 100 cc (STP) min-1 Nitrogen,
N2 as inert. Heating rate was set at 20⁰C min-1 and temperature
started from 50 to 900⁰C. Hydrogen gas production during the
pyrolysis was observed using Agilent Gas Chromatography Analyzer
7890A. Oil palm shell, oil palm frond, paddy straw and rice husk
were found to be reactive enough in a pyrolytic environment of up to
900°C since pyrolysis of these biomass starts at temperature as low as
200°C and maximum value of weight loss is achieved at about
500°C. Since there was not much different in the cellulose,
hemicelluloses and lignin fractions between oil palm shell, oil palm
frond, paddy straw and rice husk, the T-50 and R-50 values obtained
are almost similar. H2 productions started rapidly at this temperature
as well due to the decompositions of biomass inside the TGA.
Biomass with more lignin content such as oil palm shell was found to
have longer duration of H2 production compared to materials of high
cellulose and hemicelluloses contents.
Abstract: In wireless communication system, a Decision Feedback Equalizer (DFE) to cancel the intersymbol interference (ISI) is required. In this paper, an exact convergence analysis of the (DFE) adapted by the Least Mean Square (LMS) algorithm during the training phase is derived by taking into account the finite alphabet context of data transmission. This allows us to determine the shortest training sequence that allows to reach a given Mean Square Error (MSE). With the intention of avoiding the problem of ill-convergence, the paper proposes an initialization strategy for the blind decision directed (DD) algorithm. This then yields a semi-blind DFE with high speed and good convergence.
Abstract: the data quality is a kind of complex and unstructured concept, which is concerned by information systems managers. The reason of this attention is the high amount of Expenses for maintenance and cleaning of the inefficient data. Such a data more than its expenses of lack of quality, cause wrong statistics, analysis and decisions in organizations. Therefor the managers intend to improve the quality of their information systems' data. One of the basic subjects of quality improvement is the evaluation of the amount of it. In this paper, we present a precautionary method, which with its application the data of information systems would have a better quality. Our method would cover different dimensions of data quality; therefor it has necessary integrity. The presented method has tested on three dimensions of accuracy, value-added and believability and the results confirm the improvement and integrity of this method.
Abstract: Solution to unsteady Navier-Stokes equation by Splitting method in physical orthogonal algebraic curvilinear coordinate system, also termed 'Non-linear grid system' is presented. The linear terms in Navier-Stokes equation are solved by Crank- Nicholson method while the non-linear term is solved by the second order Adams-Bashforth method. This work is meant to bring together the advantage of Splitting method as pressure-velocity solver of higher efficiency with the advantage of consuming Non-linear grid system which produce more accurate results in relatively equal number of grid points as compared to Cartesian grid. The validation of Splitting method as a solution of Navier-Stokes equation in Nonlinear grid system is done by comparison with the benchmark results for lid driven cavity flow by Ghia and some case studies including Backward Facing Step Flow Problem.
Abstract: Through a proper analysis of residual strain and stress
distributions obtained at the surface of high speed milled specimens
of AA 6082–T6 aluminium alloy, the performance of an improved
indentation method is evaluated. This method integrates a special
device of indentation to a universal measuring machine. The
mentioned device allows introducing elongated indents allowing to
diminish the absolute error of measurement. It must be noted that the
present method offers the great advantage of avoiding both the
specific equipment and highly qualified personnel, and their inherent
high costs. In this work, the cutting tool geometry and high speed
parameters are selected to introduce reduced plastic damage.
Through the variation of the depth of cut, the stability of the shapes
adopted by the residual strain and stress distributions is evaluated.
The results show that the strain and stress distributions remain
unchanged, compressive and small. Moreover, these distributions
reveal a similar asymmetry when the gradients corresponding to
conventional and climb cutting zones are compared.
Abstract: This paper presents the work of signal discrimination
specifically for Electrocardiogram (ECG) waveform. ECG signal is
comprised of P, QRS, and T waves in each normal heart beat to
describe the pattern of heart rhythms corresponds to a specific
individual. Further medical diagnosis could be done to determine any
heart related disease using ECG information. The emphasis on QRS
Complex classification is further discussed to illustrate the
importance of it. Pan-Tompkins Algorithm, a widely known
technique has been adapted to realize the QRS Complex
classification process. There are eight steps involved namely
sampling, normalization, low pass filter, high pass filter (build a band
pass filter), derivation, squaring, averaging and lastly is the QRS
detection. The simulation results obtained is represented in a
Graphical User Interface (GUI) developed using MATLAB.
Abstract: A major part of the flow field involves no complicated
turbulent behavior in many turbulent flows. In this research work, in
order to reduce required memory and CPU time, the flow field was
decomposed into several blocks, each block including its special
turbulence. A two dimensional backward facing step was considered
here. Four combinations of the Prandtl mixing length and standard k-
E models were implemented as well. Computer memory and CPU
time consumption in addition to numerical convergence and accuracy
of the obtained results were mainly investigated. Observations
showed that, a suitable combination of turbulence models in different
blocks led to the results with the same accuracy as the high order
turbulence model for all of the blocks, in addition to the reductions in
memory and CPU time consumption.
Abstract: This research aimed to study on the potential of
recycling organic waste in Suan Sunandha Rajabhat University as
compost. In doing so, the composition of solid waste generated in the
campus was investigated while physical and chemical properties of
organic waste were analyzed in order to evaluate the portion of waste
suitable for recycling as compost. As a result of the study, it was
found that (1) the amount of organic waste was averaged at 299.8
kg/day in which mixed food wastes had the highest amount of 191.9
kg/day followed by mixed leave & yard wastes and mixed fruit &
vegetable wastes at the amount of 66.3 and 41.6 kg/day respectively;
(2) physical and chemical properties of organic waste in terms of
moisture content was between 69.54 to 78.15%, major elements for
plant as N, P and K were 0.14 to 0.17%, 0.46 to 0.52% and 0.16 to
0.18% respectively, and carbon/nitrogen ratio (C/N) was about 15:1
to 17.5:1; (3) recycling organic waste as compost was designed by
aerobic decomposition using mixed food wastes : mixed leave & yard
wastes : mixed fruit & vegetable wastes at the portion of 3:2:1 by
weight in accordance with the potential of their amounts and their
physical and chemical properties.