Abstract: In this study, several crossplots of the P-impedance
with the lithology logs (gamma ray, neutron porosity, deep resistivity,
water saturation and Vp/Vs curves) were made in three available
wells, which were drilled in central part of the Blue Nile basin in
depths varies from 1460m to 1600m. These crossplots were
successful to discriminate between sand and shale when using PImpedance
values, and between the wet sand and the pay sand when
using both P-impedance and Vp/Vs together. Also some impedance
sections were converted to porosity sections using linear formula to
characterize the reservoir in terms of porosity. The used crossplots
were created on log resolution, while the seismic resolution can
identify only the reservoir, unless a 3D seismic angle stacks were
available; then it would be easier to identify the pay sand with great
confidence; through high resolution seismic inversion and
geostatistical approach when using P-impedance and Vp/Vs volumes.
Abstract: The objective of this study was to evaluate the
physical and chemical characteristics of Serra da Estrela cheese and
compare these results with those of the sensory analysis. For the
study were taken six samples of Serra da Estrela cheese produced
with 6 different ecotypes of thistle in a dairy situated in Penalva do
Castelo. The chemical properties evaluated were moisture content,
protein, fat, ash, chloride and pH; the physical properties studied
were color and texture; and finally a sensory evaluation was
undertaken. The results showed moisture varying in the range 40-
48%, protein in the range 15-20%, fat between 41-45%, ash between
3.9-5.0% and chlorides varying from 1.2 to 3.0%. The pH varied
from 4.8 to 5.4. The textural properties revealed that the crust
hardness is relatively low (maximum 7.3 N), although greater than
flesh firmness (maximum 1.7 N), and also that these cheeses are in
fact soft paste type, with measurable stickiness and intense
adhesiveness. The color analysis showed that the crust is relatively
light (L* over 50), and with a predominant yellow coloration (b*
around 20 or over) although with a slight greenish tone (a* negative).
The results of the sensory analysis did not show great variability for
most of the attributes measured, although some differences were
found in attributes such as crust thickness, crust uniformity, and
creamy flesh.
Abstract: Emissions of atmospheric pollutants from ships and
harbour activities are a growing concern at international level given
their potential impacts on air quality and climate. These close-to-land
emissions have potential impact on local communities in terms of air
quality and health. Recent studies show that the impact of maritime
traffic to atmospheric particulate matter concentrations in several
coastal urban areas is comparable with the impact of road traffic of a
medium size town. However, several different approaches have been
used for these estimates making difficult a direct comparison of
results. In this work, an integrated approach based on emission
inventories and dedicated measurement campaigns has been applied
to give a comparable estimate of the impact of maritime traffic to
PM2.5 and particle number concentrations in three major harbours of
the Adriatic/Ionian Seas. The influences of local meteorology and of
the logistic layout of the harbours are discussed.
Abstract: Epidermal Growth Factor (EGF, Mw=6,045) has been
reported to have high efficiency of wound repair and anti-wrinkle
effect. However, the half-life of EGF in the body is too short to exert
the biological activity effectively when applied in free form. Growth
Factors can be stabilized by immobilization with carbohydrates from
thermal and proteolytic degradation. Low molecular weight chitosan
(LMCS) and its derivate prepared by hydrogen peroxide has high
solubility. LM6A6DC was successfully prepared as a reactive
carbohydrate for the stabilization of EGF by the reactions of LMCS
with alkalization, tosylation, azidation and reduction. The structure of
LM6A6DC was confirmed by FT-IR, 1H NMR and elementary
analysis. For enhancing the stability of free EGF, EGF was attached
with LM6A6DC by using water-soluble carbodiimide.
EGF-LM6A6DC conjugates did not show any cytotoxicity on the
Normal Human Dermal Fibroblast (NHDF) 3T3 proliferation at least
under 100 μg/ml. In the result, it was considered that LM6A6DC is
suitable to immobilize of growth factor.
Abstract: In this study, we compare the profiles of transitory
hybrid entrepreneurs and persistent hybrid entrepreneurs to determine
how they differ. Hybrid entrepreneurs (HEs) represent a significant
share of entrepreneurial activity yet little is known about them. We
define HEs as individuals who are active as entrepreneurs but do no
support themselves primarily by their enterprise. Persistent HEs
(PHEs) are not planning to transition to fulltime entrepreneurship
whereas transitory HEs (THEs) consider it probable. Our results
show that THEs and PHEs are quite similar in background. THEs are
more interested in increasing their turnover than PHEs, as expected,
but also emphasize self-fulfillment as a motive for entrepreneurship
more than PHEs. The clearest differences between THEs and PHEs
are found in their views on how well their immediate circle supports
full-time entrepreneurship, and their views of their own
entrepreneurial abilities and the market potential of their firm. Our
results support earlier arguments that hybrids should be considered
separately in research on entrepreneurial entry and self-employment.
Abstract: Natural hydrocarbon seepage has helped petroleum
exploration as a direct indicator of gas and/or oil subsurface
accumulations. Surface macro-seeps are generally an indication of a
fault in an active Petroleum Seepage System belonging to a Total
Petroleum System. This paper describes a case study in which
multiple analytical techniques were used to identify and characterize
trace petroleum-related hydrocarbons and other volatile organic
compounds in groundwater samples collected from Sousse aquifer
(Central Tunisia). The analytical techniques used for analyses of
water samples included gas chromatography-mass spectrometry (GCMS),
capillary GC with flame-ionization detection, Compound
Specific Isotope Analysis, Rock Eval Pyrolysis. The objective of the
study was to confirm the presence of gasoline and other petroleum
products or other volatile organic pollutants in those samples in order
to assess the respective implication of each of the potentially
responsible parties to the contamination of the aquifer. In addition,
the degree of contamination at different depths in the aquifer was also
of interest. The oil and gas seeps have been investigated using
biomarker and stable carbon isotope analyses to perform oil-oil and
oil-source rock correlations. The seepage gases are characterized by
high CH4 content, very low δ13CCH4 values (-71,9 ‰) and high
C1/C1–5 ratios (0.95–1.0), light deuterium–hydrogen isotope ratios (-
198 ‰) and light δ13CC2 and δ13CCO2 values (-23,8‰ and-23,8‰
respectively) indicating a thermogenic origin with the contribution of
the biogenic gas. An organic geochemistry study was carried out on
the more ten oil seep samples. This study includes light hydrocarbon
and biomarkers analyses (hopanes, steranes, n-alkanes, acyclic
isoprenoids, and aromatic steroids) using GC and GC-MS. The
studied samples show at least two distinct families, suggesting two
different types of crude oil origins: the first oil seeps appears to be
highly mature, showing evidence of chemical and/or biological
degradation and was derived from a clay-rich source rock deposited
in suboxic conditions. It has been sourced mainly by the lower
Fahdene (Albian) source rocks. The second oil seeps was derived
from a carbonate-rich source rock deposited in anoxic conditions,
well correlated with the Bahloul (Cenomanian-Turonian) source rock.
Abstract: Today, the pollution due to non-degradable material
such as plastics, has led to studies about the development of
environmental-friendly material. Because of biodegradability
obtained from natural sources, polylactid acid (PLA) and ijuk fiber
are interesting to modify into a composite. This material is also
expected to reduce the impact of environmental pollution. Surface
modification of ijuk fiber through alkalinization with 0.25 M NaOH
solution for 30 minutes was aimed to enhance its compatibility to
PLA, in order to improve properties of the composite such as the
mechanical properties. Alkalinization of the ijuk fibers annihilates
some surface components such as lignin, wax and hemicelloluse, so
the pore on the surface clearly appeared, decreasing of the density
and diameter of the ijuk fibers. The change of the ijuk fiber properties
leads to increase the mechanical properties of PLA composites
reinforced the ijuk fibers through strengthening of the mechanical
interlocking with the PLA matrix. An addition to enhance the
distribution of the fibers in the PLA matrix, the stirring during DCM
solvent evaporation from the mixture of the ijuk fibers and the
dissolved-PLA can reduce amount of the trapped-voids and fibers
pull-out phenomena, which can decrease the mechanical properties of
the composite.
Abstract: The paper deals with behaviour of the segment 50+ in
the financial market in the Czech Republic. This segment could be
said as the strong market power and it can be a crucial business
potential for financial business units. The main defined objective of
this paper is analysis of the customers´ behaviour of the segment 50-
60 years in the financial market in the Czech Republic and proposal
making of the suitable marketing approach to satisfy their demands in
the area of product, price, distribution and marketing communication
policy. This paper is based on data from one part of primary
marketing research. Paper determinates the basic problem areas as
well as definition of financial services marketing, defining the
primary research problem, hypothesis and primary research
methodology. Finally suitable marketing approach to selected sub
segment at age of 50-60 years is proposed according to marketing
research findings.
Abstract: Content Based Image Retrieval (CBIR) coupled with
Case Based Reasoning (CBR) is a paradigm that is becoming
increasingly popular in the diagnosis and therapy planning of medical
ailments utilizing the digital content of medical images. This paper
presents a survey of some of the promising approaches used in the
detection of abnormalities in retina images as well in
mammographic screening and detection of regions of interest
in MRI scans of the brain. We also describe our proposed
algorithm to detect hard exudates in fundus images of the
retina of Diabetic Retinopathy patients.
Abstract: The present work analyses different parameters of end
milling to minimize the surface roughness for AISI D2 steel. D2 Steel
is generally used for stamping or forming dies, punches, forming
rolls, knives, slitters, shear blades, tools, scrap choppers, tyre
shredders etc. Surface roughness is one of the main indices that
determines the quality of machined products and is influenced by
various cutting parameters. In machining operations, achieving
desired surface quality by optimization of machining parameters, is a
challenging job. In case of mating components the surface roughness
become more essential and is influenced by the cutting parameters,
because, these quality structures are highly correlated and are
expected to be influenced directly or indirectly by the direct effect of
process parameters or their interactive effects (i.e. on process
environment). In this work, the effects of selected process parameters
on surface roughness and subsequent setting of parameters with the
levels have been accomplished by Taguchi’s parameter design
approach. The experiments have been performed as per the
combination of levels of different process parameters suggested by
L9 orthogonal array. Experimental investigation of the end milling of
AISI D2 steel with carbide tool by varying feed, speed and depth of
cut and the surface roughness has been measured using surface
roughness tester. Analyses of variance have been performed for mean
and signal-to-noise ratio to estimate the contribution of the different
process parameters on the process.
Abstract: Iron is an essential nutrient with limited
bioavailability. Nutritional anemia caused mainly by iron deficiency
is the most recognized nutritional problem in both countries as well
as affluent societies. Rice (Oryza sativa L.) has become the most
important cereal crop for the improvement of human health due to the
starch, protein, oil, and the majority of micronutrients, particularly in
Asian countries. In this study, the iron availability and profile lipid
were evaluated for the extracts from Cibeusi varieties (black rices) of
ancient rice brans.
Results: The quality of K, B, R, E diets groups shows the same
effect on the growth of rats. Hematocrit and MCHC levels of rats fed
K, B, R and E diets were not significantly (P
Abstract: This study estimates the seismic demands of tall
buildings with central symmetric setbacks by using nonlinear time
history analysis. Three setback structures, all 60-story high with
setback in three levels, are used for evaluation. The effects of
irregularities occurred by setback are evaluated by determination of
global-drift, story-displacement and story drift. Story-displacement is
modified by roof displacement and first story displacement and story
drift is modified by global drift. All results are calculated at the
center of mass and in x and y direction. Also the absolute values of
these quantities are determined. The results show that increasing of
vertical irregularities increases the global drift of the structure and
enlarges the deformations in the height of the structure. It is also
observed that the effects of geometry irregularity in the seismic
deformations of setback structures are higher than those of mass
irregularity.
Abstract: Flow blockages referring to the increase in flow are
being considered as a vital equipment for marine current energy
conversion. However, the shape of these devices will result in
extracted energy under the operation. The present work investigates
the effect of two configurations of a grating, convergent and
divergent that located upstream, to the water flow velocity. The flow
characteristics are studied by Computational Fluid Dynamic
simulation by using the ANSYS Fluent solver for these specified
arrangements of the grating. The results indicate that distinguished
characteristics of flow velocity between “convergent” and
“divergent” grating placements is up to 10% in confined conditions.
Furthermore, the velocity in case of convergent grating is higher
than that of divergent grating.
Abstract: This research aimed to study the characteristics of a
community in the social, economic and cultural context. This
research used interviews and surveys of the members in the Patthana
Soi Ranongklang community, Dusit District, Bangkok. The results
are as follows: In terms of overall conditions and characteristics, the
Patthana Soi Ranongklang community is located on the property of
the Treasury Department. 50 years ago, the location of this
community consisted of paddy fields with limited convenience in
terms of transportation. Rama V Road was only a small narrow road
accessed only by three-wheelers there were no buses. The majority of
community members moved in from Mak Khawan Rangsan Bridge.
Thus, most community members were either workers or government
officials as they were routers not the owners of the land. Therefore,
there were no primary occupations within the 7 acres of this
community. The development of the community started in 1981. At
present, the community is continuously being developed and
modernization is rapidly flowing in. One of the reasons was because
the main roads were widened, especially Rama V Road that allows
more convenient transportation, leading to heightened citizens’
convenience. In terms of the economy and society, Rama V Road
causes the research to find out the development and expansion of
change in the conditions of the area and buildings. Some buildings
were improved and changed along the time, as well as the
development of new facilities that caused the community members to
continually become more materialistic. In the community, it has well
organized and managed jobs to each part of community members,
and areas were improved to allow the new buildings and apartments.
The trend of jobs became more varied, in terms of both jobs at home,
such as workers, merchandizing and small own businesses, and the
community jobs outside, which became much more convenient to car
drivers as they got used to the narrow roads inside the community.
The location of the community next to Rama V Road also allows
assistance from government agencies to reach the community with
ease. Moreover, the welfare of the community was well taken care of
by the community committee. In terms of education, the research
found that there are two schools: Wat Pracharabuedham School and
Wat Noi Noppakun School that are providing education within the
community. The majority in the community have received Bachelor
degrees. In areas of culture, the research found that the culture,
traditions and beliefs of people in the community were mainly
transferred from the old community: the majorities are Buddhists, so
especially beliefs in Buddhism; the main reason for this is because
the old community was situated near Wat Makut Kasattriyaram.
Therefore, the community members have always had Buddhist
temples as the centre of the community. Later years, more citizens
moved along culture in and bring traditions and beliefs with them.
The community members also took part in building a Dharma hall
named Wat Duang Jai which is 72 year old.
Abstract: Evaluated nuclear decay data for the 217Po nuclide is
presented in the present work. These data include recommended
values for the half-life T1/2, α-, β-- and γ-ray emission energies and
probabilities. Decay data from 221Rn α and 217Bi β—decays are
presented. Q(α) has been updated based on the recent published work
of the Atomic Mass Evaluation AME2012. In addition, the logft
values were calculated using the Logft program from the ENSDF
evaluation package. Moreover, the total internal conversion electrons
and the K-shell to L-shell and L-shell to M-shell and to N-shell
conversion electrons ratios K/L, L/M and L/N have been calculated
using Bricc program. Meanwhile, recommendation values or the
multi-polarities have been assigned based on recently measurement
yield a better intensity balance at the 254 keV and 264 keV gamma
transitions.
Abstract: Planning of infrastructure and processes in logistic
center within the frame of various kinds of logistic hubs and
technological activities in them represent quite complex problem.
The main goal is to design appropriate layout, which enables to
realize expected operation on the desired levels. The simulation
software represents progressive contemporary experimental
technique, which can support complex processes of infrastructure
planning and all of activities on it. It means that simulation
experiments, reflecting various planned infrastructure variants,
investigate and verify their eligibilities in relation with corresponding
expected operation. The inducted approach enables to make qualified
decisions about infrastructure investments or measures, which derive
benefit from simulation-based verifications. The paper represents
simulation software for simulation infrastructural layout and
technological activities in marshalling yard, intermodal terminal,
warehouse and combination between them as the parts of logistic
center.
Abstract: The aim of this paper is to select the most accurate
forecasting method for predicting the future values of the
unemployment rate in selected European countries. In order to do so,
several forecasting techniques adequate for forecasting time series
with trend component, were selected, namely: double exponential
smoothing (also known as Holt`s method) and Holt-Winters` method
which accounts for trend and seasonality. The results of the empirical
analysis showed that the optimal model for forecasting
unemployment rate in Greece was Holt-Winters` additive method. In
the case of Spain, according to MAPE, the optimal model was double
exponential smoothing model. Furthermore, for Croatia and Italy the
best forecasting model for unemployment rate was Holt-Winters`
multiplicative model, whereas in the case of Portugal the best model
to forecast unemployment rate was Double exponential smoothing
model. Our findings are in line with European Commission
unemployment rate estimates.
Abstract: Diminished antioxidant defense or increased
production of reactive oxygen species in the biological system can
result in oxidative stress which may lead to various
neurodegenerative diseases including Alzheimer’s disease (AD).
Microglial activation also contributes to the progression of AD by
producing several proinflammatory cytokines, nitric oxide (NO) and
prostaglandin E2 (PGE2). Oxidative stress and inflammation have
been reported to be possible pathophysiological mechanisms
underlying AD. In addition, the cholinergic hypothesis postulates that
memory impairment in patient with AD is also associated with the
deficit of cholinergic function in the brain. Although a number of
drugs have been approved for the treatment of AD, most of these
synthetic drugs have diverse side effects and yield relatively modest
benefits. Marine algae have great potential in pharmaceutical and
biomedical applications as they are valuable sources of bioactive
properties such as anticoagulation, antimicrobial, antioxidative,
anticancer and anti-inflammatory. Hence, this study aimed to provide
an overview of the properties of Malaysian seaweeds (Padina
australis, Sargassum polycystum and Caulerpa racemosa) in
inhibiting oxidative stress, neuroinflammation and cholinesterase
enzymes. These seaweeds significantly exhibited potent DPPH and
moderate superoxide anion radical scavenging ability (P
Abstract: Due to the rapid increase of Internet, web opinion
sources dynamically emerge which is useful for both potential
customers and product manufacturers for prediction and decision
purposes. These are the user generated contents written in natural
languages and are unstructured-free-texts scheme. Therefore, opinion
mining techniques become popular to automatically process customer
reviews for extracting product features and user opinions expressed
over them. Since customer reviews may contain both opinionated and
factual sentences, a supervised machine learning technique applies
for subjectivity classification to improve the mining performance. In
this paper, we dedicate our work is the task of opinion
summarization. Therefore, product feature and opinion extraction is
critical to opinion summarization, because its effectiveness
significantly affects the identification of semantic relationships. The
polarity and numeric score of all the features are determined by
Senti-WordNet Lexicon. The problem of opinion summarization
refers how to relate the opinion words with respect to a certain
feature. Probabilistic based model of supervised learning will
improve the result that is more flexible and effective.
Abstract: Zinc oxide (ZnO) is one of the light emitting materials in ultraviolet (UV) region. In addition, ZnO nanostructures are also attracting increasing research interest as buildingblocks for UV optoelectronic applications. We have succeeded in synthesizing vertically-aligned ZnO nanostructures by laser interference patterning, which is catalyst-free and non-contact technique. In this study, vertically-aligned ZnO nanowall arrays were synthesized using two-beam interference. The maximum height and average thickness of the ZnO nanowalls were about 4.5µm and 200 nm, respectively.UV lasing from a piece of the ZnO nanowall was obtained under the third harmonic of a Q-switched Nd:YAG laser excitation, and the estimated threshold power density for lasing was about 150 kW/cm2. Furthermore, UV lasing from the vertically-aligned ZnO nanowall was also achieved. The results indicate that ZnO nanowalls can be applied to random laser.