Abstract: The seismic responses of steel buildings with semirigid
post-tensioned connections (PC) are estimated and compared
with those of steel buildings with typical rigid (welded) connections
(RC). The comparison is made in terms of global and local response
parameters. The results indicate that the seismic responses in terms of
interstory shears, roof displacements, axial load and bending
moments are smaller for the buildings with PC connection. The
difference is larger for global than for local parameters, which in turn
varies from one column location to another. The reason for this
improved behavior is that the buildings with PC dissipate more
hysteretic energy than those with RC. In addition, unlike the case of
buildings with WC, for the PC structures the hysteretic energy is
mostly dissipated at the connections, which implies that structural
damage in beams and columns is not significant. According to these
results, steel buildings with PC are a viable option in high seismicity
areas because of their smaller response and self-centering connection
capacity as well as the fact that brittle failure is avoided.
Abstract: The paper presents a practical three-phase PWM
inverter suitable for low voltage, low rating energy efficient systems.
The work in the paper is conducted with the view to establishing the
significance of the loss contribution from the PWM inverter in the
determination of the complete losses of a photovoltaic (PV) arraypowered
induction motor drive water pumping system. Losses
investigated include; conduction and switching loss of the devices
and gate drive losses. It is found that the PWM inverter operates at a
reasonable variable efficiency that does not fall below 92%
depending on the load. The results between the simulated and
experimental results for the system with or without a maximum
power tracker (MPT) compares very well, within an acceptable range
of 2% margin.
Abstract: In this paper 3D FEM analysis was carried out on
double lap bonded joint with composite adherents subjected to
dynamic shear. The adherents are made of Carbon/Epoxy while the
adhesive is epoxy Araldite 2031. The maximum average shear stress
and the stress homogeneity in the adhesive layer were examined.
Three fibers textures were considered: UD; 2.5D and 3D with same
volume fiber then a parametric study based on changing the thickness
and the type of fibers texture in 2.5D was accomplished. Moreover,
adherents’ dissimilarity was also investigated. It was found that the
main parameter influencing the behavior is the longitudinal stiffness
of the adherents. An increase in the adherents’ longitudinal stiffness
induces an increase in the maximum average shear stress in the
adhesive layer and an improvement in the shear stress homogeneity
within the joint. No remarkable improvement was observed for
dissimilar adherents.
Abstract: Polycyclic aromatic hydrocarbons (PAHs) are formed
during the pyrolysis of scrap tyres to produce tyre pyrolytic oil
(TPO). Due to carcinogenic, mutagenic, and toxic properties PAHs
are priority pollutants. Hence it is essential to remove PAHs from
TPO before utilising TPO as a petroleum fuel alternative (to run the
engine). Agricultural wastes have promising future to be utilized as
biosorbent due to their cost effectiveness, abundant availability, high
biosorption capacity and renewability. Various low cost adsorbents
were prepared from natural sources. Uptake of PAHs present in tyre
pyrolytic oil was investigated using various low-cost adsorbents of
natural origin including sawdust (shisham), coconut fiber, neem bark,
chitin, activated charcoal. Adsorption experiments of different PAHs
viz. naphthalene, acenaphthalene, biphenyl and anthracene have been
carried out at ambient temperature (25°C) and at pH 7. It was
observed that for any given PAH, the adsorption capacity increases
with the lignin content. Freundlich constant Kf and 1/n have been
evaluated and it was found that the adsorption isotherms of PAHs
were in agreement with a Freundlich model, while the uptake
capacity of PAHs followed the order: activated charcoal> saw dust
(shisham) > coconut fiber > chitin. The partition coefficients in
acetone-water, and the adsorption constants at equilibrium, could be
linearly correlated with octanol–water partition coefficients. It is
observed that natural adsorbents are good alternative for PAHs
removal. Sawdust of Dalbergia sissoo, a by-product of sawmills was
found to be a promising adsorbent for the removal of PAHs present in
TPO. It is observed that adsorbents studied were comparable to those
of some conventional adsorbents.
Abstract: This work introduces a simple device designed to
perform in-situ direct shear and sinkage tests on granular materials
as sand, clays, or regolith. It consists of a box nested within a larger
box. Both have open bottoms, allowing them to be lowered into the
material. Afterwards, two rotating plates on opposite sides of the
outer box will rotate outwards in order to clear regolith on either
side, providing room for the inner box to move relative to the plates
and perform a shear test without the resistance of the surrounding
soil. From this test, Coulomb parameters, including cohesion and
internal friction angle, as well as, Bekker parameters can be inferred.
This device has been designed for a laboratory setting, but with few
modifications, could be put on the underside of a rover for use in
a remote location. The goal behind this work is to ultimately create
a compact, but accurate measuring tool to put onto a rover or any
kind of exploratory vehicle to test for regolith properties of celestial
bodies.
Abstract: This paper proposes a rotational invariant texture
feature based on the roughness property of the image for psoriasis
image analysis. In this work, we have applied this feature for image
classification and segmentation. The fuzzy concept is employed to
overcome the imprecision of roughness. Since the psoriasis lesion is
modeled by a rough surface, the feature is extended for calculating
the Psoriasis Area Severity Index value. For classification and
segmentation, the Nearest Neighbor algorithm is applied. We have
obtained promising results for identifying affected lesions by using
the roughness index and severity level estimation.
Abstract: Ti6Al4V alloy is highly used in the automotive and
aerospace industry due to its good machining characteristics. Micro
EDM drilling is commonly used to drill micro hole on extremely hard
material with very high depth to diameter ratio. In this study, the
parameters of micro-electrical discharge machining (EDM) in drilling
of Ti6Al4V alloy is optimized for higher machining accuracy with
less hole-dilation and hole taper ratio. The micro-EDM machining
parameters includes, peak current and pulse on time. Fuzzy analysis
was developed to evaluate the machining accuracy. The analysis
shows that hole-dilation and hole-taper ratio are increased with the
increasing of peak current and pulse on time. However, the surface
quality deteriorates as the peak current and pulse on time increase.
The combination that gives the optimum result for hole dilation is
medium peak current and short pulse on time. Meanwhile, the
optimum result for hole taper ratio is low peak current and short pulse
on time.
Abstract: Blueberries are widely valued for their high content in
phenolic compounds with antioxidant activity, and hence beneficial
for the human health. In this way, a study was done to determine the
phenolic composition (total phenols, anthocyanins and tannins) and
antioxidant activity of blueberries from three cultivars (Duke,
Bluecrop, and Ozarkblue) grown in two different Portuguese farms.
Initially two successive extractions were done with methanol
followed by two extractions with aqueous acetone solutions. These
extracts obtained were then used to evaluate the amount of phenolic
compounds and the antioxidant activity. The total phenols were
observed to vary from 4.9 to 8.2 mg GAE/g fresh weight, with
anthocyanin’s contents in the range 1.5-2.8 mg EMv3G/g and tannins
contents in the range 1.5- 3.8 mg/g. The results for antioxidant
activity ranged from 9.3 to 23.2 molTE/g and from 24.7 to 53.4molTE/g, when measured, respectively, by DPPH and ABTS
methods. In conclusion it was observed that, in general, the cultivar
had a visible effect on the phenols present, and furthermore, the
geographical origin showed relevance either in the phenols contents
or the antioxidant activity.
Abstract: In this paper, groundwater seepage into Amirkabir
tunnel has been estimated using analytical and numerical methods for
14 different sections of the tunnel. Site Groundwater Rating (SGR)
method also has been performed for qualitative and quantitative
classification of the tunnel sections. The obtained results of above
mentioned methods were compared together. The study shows
reasonable accordance with results of the all methods unless for two
sections of tunnel. In these two sections there are some significant
discrepancies between numerical and analytical results mainly
originated from model geometry and high overburden. SGR and the
analytical and numerical calculations, confirm high concentration of
seepage inflow in fault zones. Maximum seepage flow into tunnel has
been estimated 0.425 lit/sec/m using analytical method and 0.628
lit/sec/m using numerical method occured in crashed zone. Based on
SGR method, six sections of 14 sections in Amirkabir tunnel axis are
found to be in "No Risk" class that is supported by the analytical and
numerical seepage value of less than 0.04 lit/sec/m.
Abstract: The implementation of e-assessment as tool to support
the process of teaching and learning in university has become a
popular technological means in universities. E-Assessment provides
many advantages to the users especially the flexibility in teaching and
learning. The e-assessment system has the capability to improve its
quality of delivering education. However, there still exists a
drawback in terms of security which limits the user acceptance of the
online learning system. Even though there are studies providing
solutions for identified security threats in e-learning usage, there is no
particular model which addresses the factors that influences the
acceptance of e-assessment system by lecturers from security
perspective. The aim of this study is to explore security aspects of eassessment
in regard to the acceptance of the technology. As a result
a conceptual model of secure acceptance of e-assessment is proposed.
Both human and security factors are considered in formulation of this
conceptual model. In order to increase understanding of critical issues
related to the subject of this study, interpretive approach involving
convergent mixed method research method is proposed to be used to
execute the research. This study will be useful in providing more
insightful understanding regarding the factors that influence the user
acceptance of e-assessment system from security perspective.
Abstract: This experimental study evaluates the effect of using
Cognitive-Behavioral Therapy (CBT) and Multidimensional Self-
Concept Model (MSCM) in a drug prevention programme to increase
resiliency and reduce aggression among at-risk youth in Malaysia. A
number of 60 (N=60) university students who were at-risk of taking
drugs were involved in this study. Participants were identified with
self-rating scales, Adolescent Resilience Attitude Scale (ARAS) and
Aggression Questionnaire. Based on the mean score of these
instruments, the participants were divided into the treatment group,
and the control group. Data were analyzed using t-test. The finding
showed that the mean score of resiliency was increased in the
treatment group compared to the control group. It also shows that the
mean score of aggression was reduced in the treatment group
compared to the control group. Drug Prevention Programme was
found to help in enhancing resiliency and reducing aggression among
participants in the treatment group compared to the controlled group.
Implications were given regarding the preventive actions on drug
abuse among youth in Malaysia.
Abstract: China is currently the world's largest producer and distributor of electric bicycle (e-bike). The increasing number of e-bikes on the road is accompanied by rising injuries and even deaths of e-bike drivers. Therefore, there is a growing need to improve the safety structure of e-bikes. This 3D frictionless contact analysis is a preliminary, but necessary work for further structural design improvement of an e-bike. The contact analysis between e-bike and the ground was carried out as follows: firstly, the Penalty method was illustrated and derived from the simplest spring-mass system. This is one of the most common methods to satisfy the frictionless contact case; secondly, ANSYS static analysis was carried out to verify finite element (FE) models with contact pair (without friction) between e-bike and the ground; finally, ANSYS transient analysis was used to obtain the data of the penetration p(u) of e-bike with respect to the ground. Results obtained from the simulation are as estimated by comparing with that from theoretical method. In the future, protective shell will be designed following the stability criteria and added to the frame of e-bike. Simulation of side falling of the improvedsafety structure of e-bike will be confirmed with experimental data.
Abstract: Wind energy offers a significant advantage such as no
fuel costs and no emissions from generation. However, wind energy
sources are variable and non-dispatchable. The utility grid is able to
accommodate the variability of wind in smaller proportion along with
the daily load. However, at high penetration levels, the variability can
severely impact the utility reserve requirements and the cost
associated with it. In this paper the impact of wind energy is
evaluated in detail in formulating the total utility cost. The objective
is to minimize the overall cost of generation while ensuring the
proper management of the load. Overall cost includes the curtailment
cost, reserve cost and the reliability cost, as well as any other penalty
imposed by the regulatory authority. Different levels of wind
penetrations are explored and the cost impacts are evaluated. As the
penetration level increases significantly, the reliability becomes a
critical question to be answered. Here we increase the penetration
from the wind yet keep the reliability factor within the acceptable
limit provided by NERC. This paper uses an economic dispatch (ED)
model to incorporate wind generation into the power grid. Power
system costs are analyzed at various wind penetration levels using
Linear Programming. The goal of this study is show how the
increases in wind generation will affect power system economics.
Abstract: Standard processes, similar and limited production
lines, the production of high direct costs will be more accurate than
the use of parts of the traditional cost systems in the literature.
However, direct costs, overhead expenses, in turn, decrease the
burden of increasingly sophisticated production facilities, a situation
that led the researchers to look for the cost of traditional systems of
alternative techniques. Variety cost management approaches for
example Total quality management (TQM), just-in-time (JIT),
benchmarking, kaizen costing, targeting cost, life cycle costs (LLC),
activity-based costing (ABC) value engineering have been
introduced. Management and cost applications have changed over the
past decade and will continue to change. Modern cost systems can
provide relevant and accurate cost information. These methods
provide the decisions about customer, product and process
improvement. The aim of study is to describe and explain the
adoption and application of costing systems in SME. This purpose
reports on a survey conducted during 2014 small and medium sized
enterprises (SME) in Ankara. The survey results were evaluated
using SPSS18 package program.
Abstract: Mechanical stress has a strong effect on the magnitude
of the Barkhausen-noise in structural steels. Because the
measurements are performed at the surface of the material, for a
sample sheet, the full effect can be described by a biaxial stress field.
The measured Barkhausen-noise is dependent on the orientation of
the exciting magnetic field relative to the axis of the stress tensor.
The sample inhomogenities including the residual stress also
modifies the angular dependence of the measured Barkhausen-noise.
We have developed a laboratory device with a cross like specimen
for bi-axial bending. The measuring head allowed performing
excitations in two orthogonal directions. We could excite the two
directions independently or simultaneously with different amplitudes.
The simultaneous excitation of the two coils could be performed in
phase or with a 90 degree phase shift. In principle this allows to
measure the Barkhausen-noise at an arbitrary direction without
moving the head, or to measure the Barkhausen-noise induced by a
rotating magnetic field if a linear superposition of the two fields can
be assumed.
Abstract: This study aims to investigate the possibility of crime
prevention through CCTV by analyzing the appropriateness of the
CCTV location, whether it is installed in the hotspot of crime-prone
areas, and exploring the crime prevention effect and transition effect.
The real crime and CCTV locations of case city were converted into
the spatial data by using GIS. The data was analyzed by hotspot
analysis and weighted displacement quotient (WDQ). As study
methods, it analyzed existing relevant studies for identifying the trends
of CCTV and crime studies based on big data from 1800 to 2014 and
understanding the relation between CCTV and crime. Second, it
investigated the current situation of nationwide CCTVs and analyzed
the guidelines of CCTV installation and operation to draw attention to
the problems and indicating points of CCTV use. Third, it investigated
the crime occurrence in case areas and the current situation of CCTV
installation in the spatial aspects, and analyzed the appropriateness and
effectiveness of CCTV installation to suggest a rational installation of
CCTV and the strategic direction of crime prevention. The results
demonstrate that there was no significant effect in the installation of
CCTV on crime prevention in the case area. This indicates that CCTV
should be installed and managed in a more scientific way reflecting
local crime situations. In terms of CCTV, the methods of spatial
analysis such as GIS, which can evaluate the installation effect, and the
methods of economic analysis like cost-benefit analysis should be
developed. In addition, these methods should be distributed to local
governments across the nation for the appropriate installation of
CCTV and operation. This study intended to find a design guideline of
the optimum CCTV installation. In this regard, this study is
meaningful in that it will contribute to the creation of a safe city.
Abstract: It has become an increasing evident that large
development influences the climate. There are concerns that rising
temperature over developed areas could have negative impact and
increase living discomfort within city boundaries. Temperature trends
in Ibadan city have received little attention, yet the area has
experienced heavy urban expansion between 1972 and 2014. This
research aims at examining the impact of landuse change on surface
temperature knowing that the built-up environment absorb and store
solar energy, resulting into the Urban Heat Island (UHI) effect. The
Landsat imagery was used to examine the landuse change for a
period of 42 years (1972-2014). Land Surface Temperature (LST)
was obtained by converting the thermal band to a surface temperature
map and zonal statistic analyses was used to examine the relationship
between landuse and temperature emission. The results showed that
the settlement area increased to a large extent while the area covered
by vegetation reduced during the study period. The spatial and
temporal trends of surface temperature are related to the gradual
change in urban landuse/landcover and the settlement area has the
highest emission. This research provides useful insight into the
temporal behavior of the Ibadan city.
Abstract: Development of a method to estimate gene functions is
an important task in bioinformatics. One of the approaches for the
annotation is the identification of the metabolic pathway that genes are
involved in. Since gene expression data reflect various intracellular
phenomena, those data are considered to be related with genes’
functions. However, it has been difficult to estimate the gene function
with high accuracy. It is considered that the low accuracy of the
estimation is caused by the difficulty of accurately measuring a gene
expression. Even though they are measured under the same condition,
the gene expressions will vary usually. In this study, we proposed a
feature extraction method focusing on the variability of gene
expressions to estimate the genes' metabolic pathway accurately. First,
we estimated the distribution of each gene expression from replicate
data. Next, we calculated the similarity between all gene pairs by KL
divergence, which is a method for calculating the similarity between
distributions. Finally, we utilized the similarity vectors as feature
vectors and trained the multiclass SVM for identifying the genes'
metabolic pathway. To evaluate our developed method, we applied the
method to budding yeast and trained the multiclass SVM for
identifying the seven metabolic pathways. As a result, the accuracy
that calculated by our developed method was higher than the one that
calculated from the raw gene expression data. Thus, our developed
method combined with KL divergence is useful for identifying the
genes' metabolic pathway.
Abstract: The Cone Penetration Test (CPT) is a common in-situ
test which generally investigates a much greater volume of soil more
quickly than possible from sampling and laboratory tests. Therefore,
it has the potential to realize both cost savings and assessment of soil
properties rapidly and continuously. The principle objective of this
paper is to demonstrate the feasibility and efficiency of using
artificial neural networks (ANNs) to predict the soil angle of internal
friction (Φ) and the soil modulus of elasticity (E) from CPT results
considering the uncertainties and non-linearities of the soil. In
addition, ANNs are used to study the influence of different
parameters and recommend which parameters should be included as
input parameters to improve the prediction. Neural networks discover
relationships in the input data sets through the iterative presentation
of the data and intrinsic mapping characteristics of neural topologies.
General Regression Neural Network (GRNN) is one of the powerful
neural network architectures which is utilized in this study. A large
amount of field and experimental data including CPT results, plate
load tests, direct shear box, grain size distribution and calculated data
of overburden pressure was obtained from a large project in the
United Arab Emirates. This data was used for the training and the
validation of the neural network. A comparison was made between
the obtained results from the ANN's approach, and some common
traditional correlations that predict Φ and E from CPT results with
respect to the actual results of the collected data. The results show
that the ANN is a very powerful tool. Very good agreement was
obtained between estimated results from ANN and actual measured
results with comparison to other correlations available in the
literature. The study recommends some easily available parameters
that should be included in the estimation of the soil properties to
improve the prediction models. It is shown that the use of friction
ration in the estimation of Φ and the use of fines content in the
estimation of E considerable improve the prediction models.
Abstract: Concrete is found to undergo degradation when
subjected to elevated temperatures and loose substantial amount of its
strength. The loss of strength in concrete is mainly attributed to
decomposition of C-S-H and release of physically and chemically
bound water, which begins when the exposure temperature exceeds
100°C. When such a concrete comes in contact with moisture, the
cement paste is found rehydrate and considerable amount of strength
lost is found to recover. This paper presents results of an
experimental program carried out to investigate the effect of recuring
on strength gain of OPC concrete specimens subjected to elevated
temperatures from 200°C to 800°C, which were subjected to
retention time of two hours and four hours at the designated
temperature. Strength recoveries for concrete subjected to 7
designated elevated temperatures are compared. It is found that the
efficacy of recuring as a measure of strength recovery reduces with
increase in exposure temperature.