Abstract: Edge is variation of brightness in an image. Edge
detection is useful in many application areas such as finding forests,
rivers from a satellite image, detecting broken bone in a medical
image etc. The paper discusses about finding edge of multiple aerial
images in parallel. The proposed work tested on 38 images 37
colored and one monochrome image. The time taken to process N
images in parallel is equivalent to time taken to process 1 image in
sequential. Message Passing Interface (MPI) and Open Computing
Language (OpenCL) is used to achieve task and pixel level
parallelism respectively.
Abstract: All current experimental methods for determination of
stress intensity factors are based on the assumption that the state of
stress near the crack tip is plane stress. Therefore, these methods rely
on strain and displacement measurements made outside the near
crack tip region affected by the three-dimensional effects or by
process zone. In this paper, we develop and validate an experimental
procedure for the evaluation of stress intensity factors from the
measurements of the out-of-plane displacements in the surface area
controlled by 3D effects. The evaluation of stress intensity factors is
possible when the process zone is sufficiently small, and the
displacement field generated by the 3D effects is fully encapsulated
by K-dominance region.
Abstract: Due to the increasing efforts on saving our natural
environment a change in the structure of energy resources can be
observed - an increasing fraction of a renewable energy sources.
In many countries traditional underground coal mining loses its
significance but there are still countries, like Poland or Germany, in
which the coal based technologies have the greatest fraction in a total
energy production. This necessitates to make an effort to limit the
costs and negative effects of underground coal mining. The longwall
complex is as essential part of the underground coal mining. The
safety and the effectiveness of the work is strongly dependent of the
diagnostic state of powered roof supports.
The building of a useful and reliable diagnostic system requires
a lot of data. As the acquisition of a data of any possible operating
conditions it is important to have a possibility to generate a demanded
artificial working characteristics. In this paper a new approach of
modelling a leg pressure in the single unit of powered roof support.
The model is a result of the analysis of a typical working cycles.
Abstract: Margin-Based Principle has been proposed for a long
time, it has been proved that this principle could reduce the
structural risk and improve the performance in both theoretical
and practical aspects. Meanwhile, feed-forward neural network is
a traditional classifier, which is very hot at present with a deeper
architecture. However, the training algorithm of feed-forward neural
network is developed and generated from Widrow-Hoff Principle that
means to minimize the squared error. In this paper, we propose
a new training algorithm for feed-forward neural networks based
on Margin-Based Principle, which could effectively promote the
accuracy and generalization ability of neural network classifiers
with less labelled samples and flexible network. We have conducted
experiments on four UCI open datasets and achieved good results
as expected. In conclusion, our model could handle more sparse
labelled and more high-dimension dataset in a high accuracy while
modification from old ANN method to our method is easy and almost
free of work.
Abstract: In this paper the problem of the application of
temporal reasoning and case-based reasoning in intelligent decision
support systems is considered. The method of case-based reasoning
with temporal dependences for the solution of problems of real-time
diagnostics and forecasting in intelligent decision support systems is
described. This paper demonstrates how the temporal case-based
reasoning system can be used in intelligent decision support systems
of the car access control. This work was supported by RFBR.
Abstract: The changes of the optical and structural properties of
Bismuth-Boro-Tellurite glasses pre and post gamma irradiation were
studied. Six glass samples, with different composition [(TeO2)0.7
(B2O3)0.3]1-x (Bi2O3)x prepared by melt quenching method were
irradiated with 25kGy gamma radiation at room temperature. The
Fourier Transform Infrared Spectroscopy (FTIR) was used to explore
the structural bonding in the prepared glass samples due to exposure,
while UV-VIS Spectrophotometer was used to evaluate the changes
in the optical properties before and after irradiation. Gamma
irradiation causes profound changes in the peak intensity as shown by
FTIR spectra which is due to the breaking of the network bonding.
Before gamma irradiation, the optical band gap, Eg value decreased
from 2.44 eV to 2.15 eV with the addition of Bismuth content. The
value kept decreasing (from 2.18 eV to 2.00 eV) following exposure
to gamma radiation due to the increase of non-bridging oxygen
(NBO) and the increase of defect in the glass. In conclusion, the glass
with high content of Bi2O3 (0.30Bi) give smallest Eg and show less
changes in FTIR spectra after gamma irradiation which indicate that
this glass is more resistant to gamma radiation compared to other
glasses.
Abstract: The atmospheres in many cities along the coastal lines
in the world have been rapidly changed to coastal-industrial
atmosphere. Hence, it is vital to investigate the corrosion behavior of
steel exposed to this kind of environment. In this present study,
Electrochemical Impedance Spectrography (EIS) and film thickness
measurement were applied to monitor the corrosion behavior of
weathering steel covered with a thin layer of the electrolyte in a
wet-dry cyclic condition, simulating a coastal-industrial environment
at 25oC and 60% RH. The results indicate that in all cycles, the
corrosion rate increases during the drying process due to an increase in
anion concentration and an acceleration of oxygen diffusion enhanced
by the effect of the thinning out of the electrolyte. During the wet-dry
cyclic corrosion test, the long-term corrosion behavior of this steel
depends on the periods of exposure. Corrosion process is first
accelerated and then decelerated. The decelerating corrosion process is
contributed to the formation of the protective rust, favored by the
wet-dry cycle and the acid regeneration process during the rusting
process.
Abstract: In Hungary, the society has changed a lot for the past
25 years, and these changes could be detected in educational
situations as well. The number and the intensity of conflicts have
been increased in most fields of life, as well as at schools. Teachers
have difficulties to be able to handle school conflicts. What is more,
the new net generation, generation Z has values and behavioural
patterns different from those of the previous one, which might
generate more serious conflicts at school, especially with teachers
who were mainly socialising in a traditional teacher – student
relationship.
In Hungary, the bill CCIV of 2011 declared the foundation of
Institutes of Teacher Training in higher education institutes. One of
the tasks of the Institutes is to survey the competences and needs of
teachers working in public education and to provide further trainings
and services for them according to their needs and requirements. This
job is supported by the Social Renewal Operative Programs 4.1.2.B.
The professors of a college carried out a questionnaire and surveyed
the needs and the requirements of teachers working in the region.
Based on the results, the professors of the Institute of Teacher
Training decided to meet the requirements of teachers and to launch
short teacher further training courses in spring 2015. One of the
courses is going to focus on school conflict management through
mediation.
The aim of the pilot course is to provide conflict management
techniques for teachers and to present different mediation techniques
to them. The theoretical part of the course (5 hours) will enable
participants to understand the main points and the advantages of
mediation, while the practical part (10 hours) will involve teachers in
role plays to learn how to cope with conflict situations applying
mediation. We hope if conflicts could be reduced, it would influence
school atmosphere in a positive way and the teaching – learning
process could be more successful and effective.
Abstract: In this work, we explore the capability of the mean
shift algorithm as a powerful preprocessing tool for improving the
quality of spatial data, acquired from airborne scanners, from densely
built urban areas. On one hand, high resolution image data corrupted
by noise caused by lossy compression techniques are appropriately
smoothed while at the same time preserving the optical edges and, on
the other, low resolution LiDAR data in the form of normalized
Digital Surface Map (nDSM) is upsampled through the joint mean
shift algorithm. Experiments on both the edge-preserving smoothing
and upsampling capabilities using synthetic RGB-z data show that the
mean shift algorithm is superior to bilateral filtering as well as to
other classical smoothing and upsampling algorithms. Application of
the proposed methodology for 3D reconstruction of buildings of a
pilot region of Athens, Greece results in a significant visual
improvement of the 3D building block model.
Abstract: Networking is important among students to achieve
better understanding. Social networking plays an important role in the
education. Realizing its huge potential, various organizations,
including institutions of higher learning have moved to the area of
social networks to interact with their students especially through
Facebook. Therefore, measuring the effectiveness of Facebook as a
learning tool has become an area of interest to academicians and
researchers. Therefore, this study tried to integrate and propose new
theoretical and empirical evidences by linking the western idea of
adopting Facebook as an alternative learning platform from a
Malaysian perspective. This study, thus, aimed to fill a gap by being
among the pioneering research that tries to study the effectiveness of
adopting Facebook as a learning platform across other cultural
settings, namely Malaysia. Structural equation modeling was
employed for data analysis and hypothesis testing. This study finding
has provided some insights that would likely affect students’
awareness towards using Facebook as an alternative learning
platform in the Malaysian higher learning institutions. At the end,
future direction is proposed.
Abstract: A comprehensive CFD model is developed to
represent heterogeneous combustion and two burner designs of
supply sugar-cane bagasse into a furnace. The objective of this work
is to compare the insertion and burning of a Brazilian south-eastern
sugar-cane bagasse using a new swirl burner design against an actual
geometry under operation. The new design allows control the
particles penetration and scattering inside furnace by adjustment of
axial/tangential contributions of air feed without change their mass
flow. The model considers turbulence using RNG k-, combustion
using EDM, radiation heat transfer using DTM with 16 ray directions
and bagasse particle tracking represented by Schiller-Naumann
model. The obtained results are favorable to use of new design swirl
burner because its axial/tangential control promotes more penetration
or more scattering than actual design and allows reproduce the actual
design operation without change the overall mass flow supply.
Abstract: Prosperity of electronic equipment in photocopying
environment not only has improved work efficiency, but also has
changed indoor air quality. Considering the number of photocopying
employed, indoor air quality might be worse than in general office
environments. Determining the contribution from any type of
equipment to indoor air pollution is a complex matter. Non-methane
hydrocarbons are known to have an important role on air quality due
to their high reactivity. The presence of hazardous pollutants in
indoor air has been detected in one photocopying shop in Novi Sad,
Serbia. Air samples were collected and analyzed for five days, during
8-hr working time in three time intervals, whereas three different
sampling points were determined. Using multiple linear regression
model and software package STATISTICA 10 the concentrations of
occupational hazards and microclimates parameters were mutually
correlated. Based on the obtained multiple coefficients of
determination (0.3751, 0.2389 and 0.1975), a weak positive
correlation between the observed variables was determined. Small
values of parameter F indicated that there was no statistically
significant difference between the concentration levels of nonmethane
hydrocarbons and microclimates parameters. The results
showed that variable could be presented by the general regression
model: y = b0 + b1xi1+ b2xi2. Obtained regression equations allow to
measure the quantitative agreement between the variables and thus
obtain more accurate knowledge of their mutual relations.
Abstract: This paper deals with various questions related to
functionality and providing banking services in the European union
on the Internet. Due to the fact that we live in the information
technologies era, the Internet become a new space for doing
economic and business activities in all areas, and especially important
in banking. Accepting the busy tempo of life, in the past several years
electronic banking has become necessity and a must for most users of
banking services. On a sample of 300 web sites of the banks
operating in European Union (EU) we conduct the research on the
functionality of e-banking services offered through banks web sites
with the key objective to reveal to what extent the information
technologies are used in their business operations. Characteristics of
EU banks websites will be examined and compared to the basic
groups of business activities on the web. Also some
recommendations for the successful bank web sites will be provided.
Abstract: The purpose of this study was to develop a descriptive
profile of the adapted physical activity research using single subject
experimental designs. All research articles using single subject
experimental designs published in the journal of Adapted Physical
Activity Quarterly from 1984 to 2013 were employed as the data
source. Each of the articles was coded in a subcategory of seven
categories: (a) the size of sample; (b) the age of participants; (c) the
type of disabilities; (d) the type of data analysis; (e) the type of
designs, (f) the independent variable, and (g) the dependent variable.
Frequencies, percentages, and trend inspection were used to analyze
the data and develop a profile. The profile developed characterizes a
small portion of research articles used single subject designs, in
which most researchers used a small sample size, recruited children
as subjects, emphasized learning and behavior impairments, selected
visual inspection with descriptive statistics, preferred a multiple
baseline design, focused on effects of therapy, inclusion, and
strategy, and measured desired behaviors more often, with a
decreasing trend over years.
Abstract: The aim of this exploratory research is to understand
further how organisations can evaluate their activities, which
generate knowledge creation, to meet changing stakeholder
expectations. A Scale of Knowledge (SoK) Framework is proposed
which links knowledge management and organisational activities to
changing stakeholder expectations. The framework was informed by
the knowledge management literature, as well as empirical work
conducted via a single case study of a multi-site hospital organisation
in Saudi Arabia. Eight in-depth semi-structured interviews were
conducted with managers from across the organisation regarding
current and future stakeholder expectations, organisational
strategy/activities and knowledge management. Data were analysed
using thematic analysis and a hierarchical value map technique to
identify activities that can produce further knowledge and
consequently impact on how stakeholder expectations are met.
The SoK Framework developed may be useful to practitioners as
an analytical aid to determine if current organisational activities
produce organisational knowledge which helps them meet
(increasingly higher levels of) stakeholder expectations. The
limitations of the research and avenues for future development of the
proposed framework are discussed.
Abstract: High density electrical prospecting has been widely
used in groundwater investigation, civil engineering and
environmental survey. For efficient inversion, the forward modeling
routine, sensitivity calculation, and inversion algorithm must be
efficient. This paper attempts to provide a brief summary of the past
and ongoing developments of the method. It includes reviews of the
procedures used for data acquisition, processing and inversion of
electrical resistivity data based on compilation of academic literature.
In recent times there had been a significant evolution in field survey
designs and data inversion techniques for the resistivity method. In
general 2-D inversion for resistivity data is carried out using the
linearized least-square method with the local optimization technique
.Multi-electrode and multi-channel systems have made it possible to
conduct large 2-D, 3-D and even 4-D surveys efficiently to resolve
complex geological structures that were not possible with traditional
1-D surveys. 3-D surveys play an increasingly important role in very
complex areas where 2-D models suffer from artifacts due to off-line
structures. Continued developments in computation technology, as
well as fast data inversion techniques and software, have made it
possible to use optimization techniques to obtain model parameters to
a higher accuracy. A brief discussion on the limitations of the
electrical resistivity method has also been presented.
Abstract: In order to produce lead free piezoceramics with
optimum piezoelectric and dielectric properties, KNN modified with
Li+ (as an A site dopant) and Sb5+ (as a B site dopant)
(K0.49Na0.49Li0.02) (Nb0.96Sb0.04) O3 (referred as KNLNS in this paper)
have been synthesized using solid state reaction method and
conventional sintering technique. The ceramics were sintered in the
narrow range of 1050°C-1090°C for 2-3 h to get precise information
about sintering parameters. Detailed study of dependence of
microstructural, dielectric and piezoelectric properties on sintering
conditions was then carried out. The study suggests that the volatility
of the highly hygroscopic KNN ceramics is not only sensitive to
sintering temperatures but also to sintering durations. By merely
reducing the sintering duration for a given sintering temperature we
saw an increase in the density of the samples which was supported by
the increase in dielectric constants of the ceramics. And since density
directly or indirectly affects almost all the associated properties, other
dielectric and piezoelectric properties were also enhanced as we
approached towards the most suitable sintering temperature and
duration combination. The detailed results are reported in this paper.
Abstract: Quick adoption of e-business and emerging influence
of “Electronic Word of Mouth e-WOM” communication on guests
made leading hotel brands successful examples of electronic guest
relationship management. Main reasons behind such success are well
established procedures in collection, analysis and usage of highly
valuable data available on the Internet, generated through some form
of e-GRM programme. E-GRM is more than just a technology
solution. It’s a system which balance respective guest demands, hotel
technological capabilities and organizational culture of employees,
discharging the universal approach in guest relations “same for all”.
The purpose of this research derives from the necessity of
determining the importance of monitoring and applying e-WOM
communication as one of the methods used in managing guest
relations. This paper analyses and compares different hotelier’s
opinions on e-WOM communication.
Abstract: In this work, two fermentations at different
temperatures (25 and 30ºC), with cell recycling, were accomplished
to produce ethanol, using a mix of commercial substrates, xylose
(70%) and glucose (30%), as organic source for Scheffersomyces
stipitis. Five consecutive fermentations of 80 g L-1 (1º, 2º and 3º
recycles), 96 g L-1 (4º recycle) and 120 g L-1 (5º recycle)reduced
sugars led to a final maximum ethanol concentration of 17.2 and 34.5
g L-1, at 25 and 30ºC, respectively. Glucose was the preferred
substrate; moreover xylose startup degradation was initiated after a
remaining glucose presence in the medium. Results showed that yeast
acid treatment, performed before each cycle, provided improvements
on cell viability, accompanied by ethanol productivity of 2.16 g L-1 h-
1 at 30ºC. A maximum 36% of xylose was retained in the
fermentation medium and after five-cycle fermentation an ethanol
yield of 0.43 g ethanol/g sugars was observed. S. stipitis fermentation
capacity and tolerance showed better results at 30ºC with 83.4% of
theoretical yield referenced on initial biomass.
Abstract: The use of engineered nanomaterials has increased as
a result of their positive impact on many sectors of the economy,
including agriculture. Silver nanoparticles (AgNPs) are now used to
enhance seed germination, plant growth, and photosynthetic quantum
efficiency and as antimicrobial agents to control plant diseases. In
this study, we examined the effect of AgNP dosage on the seed
germination of three plant species: corn (Zea mays L.), watermelon
(Citrullus lanatus [Thunb.] Matsum. & Nakai) and zucchini
(Cucurbita pepo L.). This experiment was designed to study the
effect of AgNPs on germination percentage, germination rate, mean
germination time, root length and fresh and dry weight of seedlings
for the three species. Seven concentrations (0.05, 0.1, 0.5, 1, 1.5, 2
and 2.5 mg/ml) of AgNPs were examined at the seed germination
stage. The three species had different dose responses to AgNPs in
terms of germination parameters and the measured growth
characteristics. The germination rates of the three plants were
enhanced in response to AgNPs. Significant enhancement of the
germination percentage values was observed after treatment of the
watermelon and zucchini plants with AgNPs in comparison with
untreated seeds. AgNPs showed a toxic effect on corn root
elongation, whereas watermelon and zucchini seedling growth were
positively affected by certain concentrations of AgNPs. This study
showed that exposure to AgNPs caused both positive and negative
effects on plant growth and germination.