Abstract: Interactive push VOD system is a new kind of system
that incorporates push technology and interactive technique. It can
push movies to users at high speeds at off-peak hours for optimal
network usage so as to save bandwidth. This paper presents effective
software-based solution for processing mass downstream data at
terminals of interactive push VOD system, where the service can
download movie according to a viewer-s selection. The downstream
data is divided into two catalogs: (1) the carousel data delivered
according to DSM-CC protocol; (2) IP data delivered according to
Euro-DOCSIS protocol. In order to accelerate download speed and
reduce data loss rate at terminals, this software strategy introduces
caching, multi-thread and resuming mechanisms. The experiments
demonstrate advantages of the software-based solution.
Abstract: In this work, the precipitation of asphaltene from a Malaysian light oil reservoir was studies. A series of experiments were designed and carried out to examine the effect of CO2 injection on asphaltene precipitation. Different pressures of injections were used in Dynamic flooding experiment in order to investigate the effect of pressure versus injection pore volume of CO2. These dynamic displacement tests simulate reservoir condition. Results show that by increasing the pore volume of injected gas asphaltene precipitation will increases, also rise in injection pressure causes less precipitation. Sandstone core plug was used to represent reservoir formation during displacement test; therefore it made it possible to study the effect of present of asphaltene on formation. It is found out that the precipitated asphaltene can reduce permeability and porosity which is not favorable during oil production.
Abstract: Diabetes mellitus (DM) is frequently characterized by
autonomic nervous dysfunction. Analysis of heart rate variability
(HRV) has become a popular noninvasive tool for assessing the
activities of autonomic nervous system (ANS). In this paper, changes
in ANS activity are quantified by means of frequency and time
domain analysis of R-R interval variability. Electrocardiograms
(ECG) of 16 patients suffering from DM and of 16 healthy volunteers
were recorded. Frequency domain analysis of extracted normal to
normal interval (NN interval) data indicates significant difference in
very low frequency (VLF) power, low frequency (LF) power and
high frequency (HF) power, between the DM patients and control
group. Time domain measures, standard deviation of NN interval
(SDNN), root mean square of successive NN interval differences
(RMSSD), successive NN intervals differing more than 50 ms (NN50
Count), percentage value of NN50 count (pNN50), HRV triangular
index and triangular interpolation of NN intervals (TINN) also show
significant difference between the DM patients and control group.
Abstract: A kinetic model for propane dehydrogenation in an
industrial moving bed reactor is developed based on the reported
reaction scheme. The kinetic parameters and activity constant are
fine tuned with several sets of balanced plant data. Plant data at
different operating conditions is applied to validate the model and
the results show a good agreement between the model
predictions and plant observations in terms of the amount of main
product, propylene produced. The simulation analysis of key
variables such as inlet temperature of each reactor (Tinrx) and
hydrogen to total hydrocarbon ratio (H2/THC) affecting process
performance is performed to identify the operating condition to
maximize the production of propylene. Within the range of operating
conditions applied in the present studies, the operating condition to
maximize the propylene production at the same weighted average
inlet temperature (WAIT) is ΔTinrx1= -2, ΔTinrx2= +1, ΔTinrx3= +1 ,
ΔTinrx4= +2 and ΔH2/THC= -0.02. Under this condition, the surplus
propylene produced is 7.07 tons/day as compared with base case.
Abstract: A series of experiments were carried out to study
unsteady behavior of the flow field as well as the boundary layer of
an airfoil oscillating in plunging motion in a subsonic wind tunnel.
The measurements involved surface pressure distribution
complimented with surface-mounted hot-films. The effect of leadingedge
roughness that simulates surface irregularities on the wind
turbine blades was also studied on variations of aerodynamic loads
and boundary layer behavior.
Abstract: Insufficient Quality of Service (QoS) of Voice over
Internet Protocol (VoIP) is a growing concern that has lead the need
for research and study. In this paper we investigate the performance
of VoIP and the impact of resource limitations on the performance of
Access Networks. The impact of VoIP performance in Access
Networks is particularly important in regions where Internet
resources are limited and the cost of improving these resources is
prohibitive. It is clear that perceived VoIP performance, as measured
by mean opinion score [2] in experiments, where subjects are asked
to rate communication quality, is determined by end-to-end delay on
the communication path, delay variation, packet loss, echo, the
coding algorithm in use and noise. These performance indicators can
be measured and the affect in the Access Network can be estimated.
This paper investigates the congestion in the Access Network to the
overall performance of VoIP services with the presence of other
substantial uses of internet and ways in which Access Networks can
be designed to improve VoIP performance. Methods for analyzing
the impact of the Access Network on VoIP performance will be
surveyed and reviewed. This paper also considers some approaches
for improving performance of VoIP by carrying out experiments
using Network Simulator version 2 (NS2) software with a view to
gaining a better understanding of the design of Access Networks.
Abstract: In the present paper, a numerical investigation has
been carried out to classify and clarify the effects of paramount
parameters on turbulent impinging slot jets. The effects of nozzle-s
exit turbulent intensity, distance between nozzle and impinging plate
are studied at Reynolds number 5000 and 20000. In addition, the
effect of Mach number that is varied between 0.3-0.8 at a constant
Reynolds number 133000 is investigated to elucidate the effect of
compressibility in impinging jet upon a flat plate. The wall that is
located at the same level with nozzle-s exit confines the flow. A
compressible finite volume solver is implemented for simulation the
flow behavior. One equation Spalart-Allmaras turbulent model is
used to simulate turbulent flow at this study. Assessment of the
Spalart-Allmaras turbulent model at high nozzle to plate distance,
and giving enough insights to characterize the effect of Mach number
at high Reynolds number for the complex impinging jet flow are the
remarkable results of this study.
Abstract: Studies regarding the determination of population
trend of Lipaphis erysimi (kalt.) and its associated natural enemies in
different Brassica lines along with the effect of gamma radiation on
their population were conducted at Agricultural Research Farm,
Malakandher, Khyber Pakhtunkhwa Agricultural University
Peshawar during spring 2006. Three different Brassica lines F6B3,
F6B6 and F6B7 were used, which were replicated four times in
Randomized Complete Block Design. The data revealed that aphid
infestation invariably stated in all three varieties during last week of
February 2006 (1st observation). The peak population of 4.39 aphids
leaf-1 was s recorded during 2nd week of March and lowest population
of 1.02 aphids leaf-1 was recorded during 5th week of March. The
species of lady bird beetle (Coccinella septempunctata) and Syrphid
fly (Syrphus balteatus) first appeared on 24th February with a mean
number of 0.40 lady bird beetle leaf-1 and 0.87 Syrphid fly leaf-1,
respectively. At the time when aphid population started to increase
the peak population of C. septempunctata (0.70 lady bird beetle leaf-
1) and S. balteatus (1.04 syrphid fly leaf-1) was recorded on the 2nd
week of March. Chrysoperla carnea appeared in the 1st week of
March and their peak population was recorded during the 3rd week of
March with mean population of 1.46 C. carnea leaf-1. Among all the
Brassica lines, F6B7 showed comparatively more resistance as
compared to F6B3 F6B6. F6B3 showed least resistance against L.
erysimi, which was found to be the most susceptible cultivar. F6B7
was also found superior in terms of natural enemies. Maximum
number of all natural enemies was recorded on this variety followed
by F6B6. Lowest number of natural enemies was recorded in F6B3.
No significant effect was recorded for the effect of gamma radiation
on the population of aphids, natural enemies and on the varieties.
Abstract: This paper studies stability of homogeneous beams
with piezoelectric layers subjected to axial load that is simply
supported at both ends lies on a continuous elastic foundation. The
displacement field of beam is assumed based on first order shear
deformation beam theory. Applying the Hamilton's principle, the
governing equation is established. The influences of applied voltage,
dimensionless geometrical parameter and foundation coefficient on
the stability of beam are presented. To investigate the accuracy of the
present analysis, a compression study is carried out with a known
data.
Abstract: The advancement of smartphones, wireless
networking and Near Field Communication (NFC) technology have
opened up a new approach to indoor navigation. Although NFC
technology has been used to support electronic commerce, access
control, and ticketing, there is a lack of research work on building
NFC-based indoor navigation system for smartphone users. This
paper presents an indoor interactive navigation system (named
I2Navi) based on NFC technology for users to navigate within a
building with ease using their smartphones. The I2Navi system has
been implemented at the Faculty of Engineering (FOE), Multimedia
University (MMU) to enable students, parents, visitors who own
NFC-enabled Android smartphones to navigate themselves within the
faculty. An evaluation is carried out and the results show positive
response to the proposed indoor navigation system using NFC and
smartphone technologies.
Abstract: Resistance spot welding process comprises of electric,
thermal and mechanical phenomenon, which makes this process
complex and highly non-linear and thus, it becomes difficult to model
it. In order to obtain good weld nugget during spot welding, hit and
trial welds are usually done which is very costly. Therefore the
numerical simulation research has been conducted to understand the
whole process. In this paper three different cases were analyzed by
varying the tip contact area and it was observed that, with the
variation of tip contact area the nugget formation at the faying
surface is affected. The tip contact area of the welding electrode
becomes large with long welding cycles. Therefore in order to
maintain consistency of nugget formation during the welding process,
the current compensation in control feedback is required. If the
contact area of the welding electrode tip is reduced, a large amount of
current flows through the faying surface, as a result of which
sputtering occurs.
Abstract: In this paper, the local grid refinement is focused by
using a nested grid technique. The Cartesian grid numerical method is
developed for simulating unsteady, viscous, incompressible flows
with complex immersed boundaries. A finite volume method is used in
conjunction with a two-step fractional-step procedure. The key aspects
that need to be considered in developing such a nested grid solver are
imposition of interface conditions on the inter-block and accurate
discretization of the governing equation in cells that are with the
inter-block as a control surface. A new interpolation procedure is
presented which allows systematic development of a spatial
discretization scheme that preserves the spatial accuracy of the
underlying solver. The present nested grid method has been tested by
two numerical examples to examine its performance in the two
dimensional problems. The numerical examples include flow past a
circular cylinder symmetrically installed in a Channel and flow past
two circular cylinders with different diameters. From the numerical
experiments, the ability of the solver to simulate flows with
complicated immersed boundaries is demonstrated and the nested grid
approach can efficiently speed up the numerical solutions.
Abstract: The dominant judgment for earthquake damaged reinforced concrete (RC) structures is to rebuild them with the new ones. Consequently, this paper estimates if there is chance to repair earthquake RC beams and obtain economical contribution to modern day society. Therefore, the totally damaged (damaged in shear under cyclic load) reinforced concrete (RC) beams repaired and strengthened by externally bonded carbon fibre reinforced polymer (CFRP) strips in this study. Four specimens, apart from the reference beam, were separated into two distinct groups. Two experimental beams in the first group primarily tested up to failure then appropriately repaired and strengthened with CFRP strips. Two undamaged specimens from the second group were not repaired but strengthened by the identical strengthening scheme as the first group for comparison. This study studies whether earthquake damaged RC beams that have been repaired and strengthened will validate similar strength and behavior to equally strengthened, undamaged RC beams. Accordingly, a strength correspondence according to strengthened specimens was acquired for the repaired and strengthened specimens. Test results confirmed that repair and strengthening, which were estimated in the experimental program, were effective for the specimens with the cracking patterns considered in the experimental program.
Abstract: In high powered dense wavelength division
multiplexed (WDM) systems with low chromatic dispersion,
four-wave mixing (FWM) can prove to be a major source of noise.
The MultiCanonical Monte Carlo Method (MCMC) and the Split
Step Fourier Method (SSFM) are combined to accurately evaluate the
probability density function of the decision variable of a receiver,
limited by FWM. The combination of the two methods leads to more
accurate results, and offers the possibility of adding other optical
noises such as the Amplified Spontaneous Emission (ASE) noise.
Abstract: The aged are faced with increasing risk for falls. The
aged have the easily fragile bones than others. When falls have
occurred, it is important to detect this emergency state because such
events often lead to more serious illness or even death. A
implementation of PDA system, for detection of emergency situation,
was developed using 3-axis accelerometer in this paper as follows.
The signals were acquired from the 3-axis accelerometer, and then
transmitted to the PDA through Bluetooth module. This system can
classify the human activity, and also detect the emergency state like
falls. When the fall occurs, the system generates the alarm on the
PDA. If a subject does not respond to the alarm, the system determines
whether the current situation is an emergency state or not, and then
sends some information to the emergency center in the case of urgent
situation. Three different studies were conducted on 12 experimental
subjects, with results indicating a good accuracy. The first study was
performed to detect the posture change of human daily activity. The
second study was performed to detect the correct direction of fall. The
third study was conducted to check the classification of the daily
physical activity. Each test was lasted at least 1 min. in third study.
The output of acceleration signal was compared and evaluated by
changing a various posture after attaching a 3-axis accelerometer
module on the chest. The newly developed system has some important
features such as portability, convenience and low cost. One of the
main advantages of this system is that it is available at home
healthcare environment. Another important feature lies in low cost to
manufacture device. The implemented system can detect the fall
accurately, so will be widely used in emergency situation.
Abstract: The crystallization kinetics and phase transformation
of SiO2.Al2O3.0,56P2O5.1,8CaO.0,56CaF2 glass have been
investigated using differential thermal analysis (DTA), x-ray
diffraction (XRD), and scanning electron microscopy (SEM). Glass
samples were obtained by melting the glass mixture at 14500С/120
min. in platinum crucibles. The mixture were prepared from
chemically pure reagents: SiO2, Al(OH)3, H3PO4, CaCO3 and CaF2.
The non-isothermal kinetics of crystallization was studied by
applying the DTA measurements carried out at various heating rates.
The activation energies of crystallization and viscous flow were
measured as 348,4 kJ.mol–1 and 479,7 kJ.mol–1 respectively. Value of
Avrami parameter n ≈ 3 correspond to a three dimensional of crystal
growth mechanism. The major crystalline phase determined by XRD
analysis was fluorapatite (Ca(PO4)3F) and as the minor phases –
fluormargarite (CaAl2(Al2SiO2)10F2) and vitlokite (Ca9P6O24). The
resulting glass-ceramic has a homogeneous microstructure, composed
of prismatic crystals, evenly distributed in glass phase.
Abstract: The concentrations of As, Hg, Co, Cr and Cd were
tested for each soil sample, and their spatial patterns were analyzed
by the semivariogram approach of geostatistics and geographical
information system technology. Multivariate statistic approaches
(principal component analysis and cluster analysis) were used to
identify heavy metal sources and their spatial pattern. Principal
component analysis coupled with correlation between heavy metals
showed that primary inputs of As, Hg and Cd were due to
anthropogenic while, Co, and Cr were associated with pedogenic
factors. Ordinary kriging was carried out to map the spatial patters of
heavy metals. The high pollution sources evaluated was related with
usage of urban and industrial wastewater. The results of this study
helpful for risk assessment of environmental pollution for decision
making for industrial adjustment and remedy soil pollution.
Abstract: Following harvest, fresh produce needs to be cooled
immediately in a room where the air temperature and the relative air
humidity are controlled to maintain the produce quality. In this paper,
an experimental study for forced air cooling of fresh produce
(cauliflower) is performed using a pilot developed within our
laboratory. Furthermore, a numerical simulation of spherical
produces, taking into account the aerodynamic aspect and also the
heat transfer in the produce and in the air, was carried out using a
finite element method. At the end of this communication,
experimental results are presented and compared with the simulation.
Abstract: The work reported in this paper is motivated by the fact that there is a need to apply autonomic computing concepts to parallel computing systems. Advancing on prior work based on intelligent cores [36], a swarm-array computing approach, this paper focuses on 'Intelligent agents' another swarm-array computing approach in which the task to be executed on a parallel computing core is considered as a swarm of autonomous agents. A task is carried to a computing core by carrier agents and is seamlessly transferred between cores in the event of a predicted failure, thereby achieving self-ware objectives of autonomic computing. The feasibility of the proposed swarm-array computing approach is validated on a multi-agent simulator.
Abstract: In the present study, a steady-state simulation model
has been developed to evaluate the system performance of a
transcritical carbon dioxide heat pump system for simultaneous water
cooling and heating. Both the evaporator (including both two-phase
and superheated zone) and gas cooler models consider the highly
variable heat transfer characteristics of CO2 and pressure drop. The
numerical simulation model of transcritical CO2 heat pump has been
validated by test data obtained from experiments on the heat pump
prototype. Comparison between the test results and the model
prediction for system COP variation with compressor discharge
pressure shows a modest agreement with a maximum deviation of
15% and the trends are fairly similar. Comparison for other operating
parameters also shows fairly similar deviation between the test
results and the model prediction. Finally, the simulation results are
presented to study the effects of operating parameters such as,
temperature of heat exchanger fluid at the inlet, discharge pressure,
compressor speed on system performance of CO2 heat pump, suitable
in a dairy plant where simultaneous cooling at 4oC and heating at
73oC are required. Results show that good heat transfer properties of
CO2 for both two-phase and supercritical region and efficient
compression process contribute a lot for high system COPs.