Abstract: Nowadays, quasi-continuous wave diode lasers are
used in a widespread variety of applications. Temperature effects in
these lasers can strongly influence their performance. In this paper,
the effects of temperature have been experimentally investigated on
different features of a 60W-QCW diode laser. The obtained results
indicate that the conversion efficiency and operation voltage of diode
laser decrease with the augmentation of the working temperature
associated with a redshift in the laser peak wavelength. Experimental
results show the emission peak wavelength of laser shifts 0.26 nm
and the conversion efficiency decreases 1.76 % with the increase of
temperature from 40 to 50 ̊C. Present study also shows the slope
efficiency decreases gradually at low temperatures and rapidly at
higher temperatures. Regarding the close dependence of the
mentioned parameters to the operating temperature, it is of great
importance to carefully control the working temperature of diode
laser, particularly for medical applications.
Abstract: The effect of thermally induced stress on the modal
properties of highly elliptical core optical fibers is studied in this
work using a finite element method. The stress analysis is carried out
and anisotropic refractive index change is calculated using both the
conventional plane strain approximation and the generalized plane
strain approach. After considering the stress optical effect, the modal
analysis of the fiber is performed to obtain the solutions of
fundamental and higher order modes. The modal effective index,
modal birefringence, group effective index, group birefringence, and
dispersion of different modes of the fiber are presented. For
propagation properties, it can be seen that the results depend much on
the approach of stress analysis.
Abstract: Films of pure tin oxide SnO2 and in presence of
antimony atoms (SnO2-Sb) deposited onto glass substrates have
shown a sufficiently high energy gap to be transparent in the visible
region, a high electrical mobility and a carrier concentration which
displays a good electrical conductivity [1]. In this work, the effects of
polycrystalline silicon substrate on the optical properties of pure and
Sb doped tin oxide is investigated.
We used the APCVD (atmospheric pressure chemical vapour
deposition) technique, which is a low-cost and simple technique,
under nitrogen ambient, for growing this material. A series of SnO2
and SnO2-Sb have been deposited onto polycrystalline silicon
substrates with different contents of antimony atoms at the same
conditions of deposition (substrate temperature, flow oxygen,
duration and nitrogen atmosphere of the reactor). The effect of the
substrate in terms of morphology and nonlinear optical properties,
mainly the reflectance, was studied. The reflectance intensity of the
device, compared to the reflectance of tin oxide films deposited
directly on glass substrate, is clearly reduced on the overall
wavelength range. It is obvious that the roughness of the poly-c
silicon plays an important role by improving the reflectance and
hence the optical parameters.
A clear shift in the minimum of the reflectance upon doping level
is observed. This minimum corresponds to strong free carrier
absorption, resulting in different plasma frequency. This effect is
followed by an increase in the reflectance depending of the antimony
doping. Applying the extended Drude theory to the combining
optical and electrical obtained results these effects are discussed.
Abstract: The design of a steam turbine is a very complex
engineering operation that can be simplified and improved thanks to
computer-aided multi-objective optimization. This process makes use
of existing optimization algorithms and losses correlations to identify
those geometries that deliver the best balance of performance (i.e.
Pareto-optimal points).
This paper deals with a one-dimensional multi-objective and
multi-point optimization of a single-stage steam turbine. Using a
genetic optimization algorithm and an algebraic one-dimensional
ideal gas-path model based on loss and deviation correlations, a code
capable of performing the optimization of a predefined steam turbine
stage was developed. More specifically, during this study the
parameters modified (i.e. decision variables) to identify the best
performing geometries were solidity and angles both for stator and
rotor cascades, while the objective functions to maximize were totalto-
static efficiency and specific work done.
Finally, an accurate analysis of the obtained results was carried
out.
Abstract: It is hard to percept the interaction process with machines when visual information is not available. In this paper, we have addressed this issue to provide interaction through visual techniques. Posture recognition is done for American Sign Language to recognize static alphabets and numbers. 3D information is exploited to obtain segmentation of hands and face using normal Gaussian distribution and depth information. Features for posture recognition are computed using statistical and geometrical properties which are translation, rotation and scale invariant. Hu-Moment as statistical features and; circularity and rectangularity as geometrical features are incorporated to build the feature vectors. These feature vectors are used to train SVM for classification that recognizes static alphabets and numbers. For the alphabets, curvature analysis is carried out to reduce the misclassifications. The experimental results show that proposed system recognizes posture symbols by achieving recognition rate of 98.65% and 98.6% for ASL alphabets and numbers respectively.
Abstract: Since the 1940s, many promising telepresence
research results have been obtained. However, telepresence
technology still has not reached industrial usage. As human
intelligence is necessary for successful execution of most manual
assembly tasks, the ability of the human is hindered in some cases,
such as the assembly of heavy parts of small/medium lots or
prototypes. In such a case of manual assembly, the help of industrial
robots is mandatory. The telepresence technology can be considered
as a solution for performing assembly tasks, where the human
intelligence and haptic sense are needed to identify and minimize the
errors during an assembly process and a robot is needed to carry
heavy parts. In this paper, preliminary steps to integrate the
telepresence technology into industrial robot systems are introduced.
The system described here combines both, the human haptic sense
and the industrial robot capability to perform a manual assembly task
remotely using a force feedback joystick. Mapping between the
joystick-s Degrees of Freedom (DOF) and the robot-s ones are
introduced. Simulation and experimental results are shown and future
work is discussed.
Abstract: This paper concerns a formal model to help the
simulation of agent societies where institutional roles and
institutional links can be specified operationally. That is, this paper
concerns institutional roles that can be specified in terms of a minimal behavioral capability that an agent should have in order to
enact that role and, thus, to perform the set of institutional functions that role is responsible for. Correspondingly, the paper concerns
institutional links that can be specified in terms of a minimal
interactional capability that two agents should have in order to, while
enacting the two institutional roles that are linked by that institutional
link, perform for each other the institutional functions supported by
that institutional link. The paper proposes a cognitive architecture
approach to institutional roles and institutional links, that is, an approach in which a institutional role is seen as an abstract cognitive
architecture that should be implemented by any concrete agent (or set of concrete agents) that enacts the institutional role, and in which
institutional links are seen as interactions between the two abstract
cognitive agents that model the two linked institutional roles. We
introduce a cognitive architecture for such purpose, called the
Institutional BCC (IBCC) model, which lifts Yoav Shoham-s BCC
(Beliefs-Capabilities-Commitments) agent architecture to social
contexts. We show how the resulting model can be taken as a means
for a cognitive architecture account of institutional roles and
institutional links of agent societies. Finally, we present an example
of a generic scheme for certain fragments of the social organization
of agent societies, where institutional roles and institutional links are
given in terms of the model.
Abstract: This study developed a high efficient and combined
biological and chemical filter treatment process. This process used
PAC (Powder Activated Carbon), Alum and attached growth
treatment process. The system removals of total nitrogen and total
phosphorus ratio of two were as high as 70% and 73%, moreover, the
effluent water was suitable to urban and agricultural water. Also the
advantages of this process are not only occupies small place but is
simple, economic and easy operating. Besides, our developed process
can keep stable process efficiency even in relative low load level.
Therefore, this study judges that use of the high efficient and
combined biological and chemical filter treatment process, it is
expected that the effluent water in this system can be reused as urban
and agricultural water.
Abstract: Estimating the lifetime distribution of computer networks in which nodes and links exist in time and are bound for failure is very useful in various applications. This problem is known to be NP-hard. In this paper we present efficient combinatorial approaches to Monte Carlo estimation of network lifetime distribution. We also present some simulation results.
Abstract: The general global behavior of particle S a non-linear (Q - xy)2 potential cannot be revealed a Poincare surface of section method (PSS) because inost trajectories take practically infinitely long time to integrate numerically before they come back to the surface. In this study as an alternative to PSS, a multiple scale perturbation is applied to analyze global adiabatic, non-adiabatic and chaotic behavior of particles in this potential. It was found that the results can be summarized as a form of a Fermi-like map. Additionally, this method gives a variation of global stochasticity criteria with Q.
Abstract: This paper reports on the theoretical performance
analysis of the 1.3 μm In0.42Ga0.58As /In0.26Ga0.74As multiple quantum
well (MQW) vertical cavity surface emitting laser (VCSEL) on the
ternary In0.31Ga0.69As substrate. The output power of 2.2 mW has
been obtained at room temperature for 7.5 mA injection current. The
material gain has been estimated to be ~3156 cm-1 at room
temperature with the injection carrier concentration of 2×1017 cm-3.
The modulation bandwidth of this laser is measured to be 9.34 GHz
at room temperature for the biasing current of 2 mA above the
threshold value. The outcomes reveal that the proposed InGaAsbased
MQW laser is the promising one for optical communication
system.
Abstract: Oral health is particular important to the hospitalized
patients with chronic schizophrenia for an extreme high potential of the respiratory infections. Due to the degeneration of physical capability, patients of this kind typically fall dependent in the activity of daily living (ADL). A very high percentage of patients had dental
problems of which mostly could be easily avoid by easy regular tooth brushing. Purpose of the project is to develop a mechanism in helping the schizophrenia patients in rebuilding a tooth-cleaning habit. The
project observed and evaluated the tooth-cleaning behavior of 100
male patients in a psychiatric hospital, and found the majority of them
ignored such an activity in a three-month period of time. In the meantime, the primary care-givers were not aware or not convinced
the importance of such a need of dental hygiene, and thus few if any
tooth cleaning training or knowledge on dental hygiene were given to
the patients. The project then developed a program based on the numerous observations and discussions. The improvement program
included patients- group education, care-givers- training, and a
tool-kit for tooth-brush holding was erected. The project launched
with some incentive package. The outcomes were encouraging with
87% of the patients had rebuilt their tooth-brushing habits against
previous 22%, and the tooth cleaning kits were 100% kept against 22%
in the past. This project had significantly improved the oral health of
the patients. The project, included the procedure and the tool-kit
holder specific for this purpose, was a good examples for psychiatric
hospitals.
Abstract: This article presents the boundary conditions for the problem of turbulent supersonic gas flow in a plane channel with a perpendicular injection jets. The non-reflection boundary conditions for direct modeling of compressible viscous gases are studied. A formulation using the NSCBC (Navier- Stocks characteristic boundary conditions) through boundaries is derived for the subsonic inflow and subsonic non-reflection outflow situations. Verification of the constructed algorithm of boundary conditions is carried out by solving a test problem of perpendicular sound of jets injection into a supersonic gas flow in a plane channel.
Abstract: Environment today is featured with aging population,
increasing prevalence of chronic disease and complex of medical
treatment. Safe use of pharmaceutics relied very much on the efforts
made by both the health- related organizations and as well as the
government agencies. As far as the specialization concern in providing
health services to the patients, the government actively issued and
implemented the divisions of medical treatment and pharmaceutical to
improve the quality of care and to reduce medication errors and ensure
public health. Pharmaceutical sub-sector policy has been implemented
for 13 years. This study attempts to explore the factors that affect the
patients- behavior intention of refilling a prescription from a NHIB
pharmacy. Samples were those patients refilling their prescriptions
with the case NHIB pharmacies. A self-administered questionnaire
was used to collect respondents- information while the patients or
family members visit the pharmacy for the refilling. 1,200
questionnaires were dispatched in 37 pharmacies that randomly
selected from Pingtung City, Dongkang, Chaozhou, Hengchun areas.
732 responses were gained with 604 valid samples for further analyses.
Results of data analyses indicated that respondents- attitude,
subjective norm, perceived behavior control and behavior intentions
toward refilling behavior varied from some demographic variables to
another. This research also suggested adding actual behavior, either by
a self-report or observed, into the research.
Abstract: Privacy issues commonly discussed among
researchers, practitioners, and end-users in pervasive healthcare.
Pervasive healthcare systems are applications that can support
patient-s need anytime and anywhere. However, pervasive healthcare
raises privacy concerns since it can lead to situations where patients
may not be aware that their private information is being shared and
becomes vulnerable to threat. We have systematically analyzed the
privacy issues and present a summary in tabular form to show the
relationship among the issues. The six issues identified are medical
information misuse, prescription leakage, medical information
eavesdropping, social implications for the patient, patient difficulties
in managing privacy settings, and lack of support in designing
privacy-sensitive applications. We narrow down the issues and chose
to focus on the issue of 'lack of support in designing privacysensitive
applications' by proposing a privacy-sensitive architecture
specifically designed for pervasive healthcare monitoring systems.
Abstract: Lutein is a dietary oxycarotenoid which is found
to reduce the risks of Age-related Macular Degeneration
(AMD). Supercritical fluid extraction of lutein esters from
marigold petals was carried out and was found to be much
effective than conventional solvent extraction. The
saponification of pre-concentrated lutein esters to produce free
lutein was studied which showed a composition of about 88%
total carotenoids (UV-VIS spectrophotometry) and 90.7%
lutein (HPLC). The lipase catalyzed hydrolysis of lutein esters
in conventional medium was investigated. The optimal
temperature, pH, enzyme concentration and water activity
were found to be 50°C, 7, 15% and 0.33 respectively and the
activity loss of lipase was about 25% after 8 times re-use in at
50°C for 12 days. However, the lipase catalyzed hydrolysis of
lutein esters in conventional media resulted in poor
conversions (16.4%).
Abstract: Comparison of two approaches for the simulation of
the dynamic behaviour of a permanent magnet linear actuator is
presented. These are full coupled model, where the electromagnetic
field, electric circuit and mechanical motion problems are solved
simultaneously, and decoupled model, where first a set of static
magnetic filed analysis is carried out and then the electric circuit and
mechanical motion equations are solved employing bi-cubic spline
approximations of the field analysis results. The results show that the
proposed decoupled model is of satisfactory accuracy and gives more
flexibility when the actuator response is required to be estimated for
different external conditions, e.g. external circuit parameters or
mechanical loads.
Abstract: Multi-energy systems will enhance the system
reliability and power quality. This paper presents an integrated
approach for the design and operation of distributed energy resources
(DER) systems, based on energy hub modeling. A multi-objective
optimization model is developed by considering an integrated view of
electricity and natural gas network to analyze the optimal design and
operating condition of DER systems, by considering two conflicting
objectives, namely, minimization of total cost and the minimization
of environmental impact which is assessed in terms of CO2
emissions. The mathematical model considers energy demands of the
site, local climate data, and utility tariff structure, as well as technical
and financial characteristics of the candidate DER technologies. To
provide energy demands, energy systems including photovoltaic, and
co-generation systems, boiler, central power grid are considered. As
an illustrative example, a hotel in Iran demonstrates potential
applications of the proposed method. The results prove that
increasing the satisfaction degree of environmental objective leads to
increased total cost.
Abstract: Echocardiography imaging is one of the most common diagnostic tests that are widely used for assessing the abnormalities of the regional heart ventricle function. The main goal of the image enhancement task in 2D-echocardiography (2DE) is to solve two major anatomical structure problems; speckle noise and low quality. Therefore, speckle noise reduction is one of the important steps that used as a pre-processing to reduce the distortion effects in 2DE image segmentation. In this paper, we present the common filters that based on some form of low-pass spatial smoothing filters such as Mean, Gaussian, and Median. The Laplacian filter was used as a high-pass sharpening filter. A comparative analysis was presented to test the effectiveness of these filters after being applied to original 2DE images of 4-chamber and 2-chamber views. Three statistical quantity measures: root mean square error (RMSE), peak signal-to-ratio (PSNR) and signal-tonoise ratio (SNR) are used to evaluate the filter performance quantitatively on the output enhanced image.
Abstract: Falling has been one of the major concerns and threats
to the independence of the elderly in their daily lives. With the
worldwide significant growth of the aging population, it is essential
to have a promising solution of fall detection which is able to operate
at high accuracy in real-time and supports large scale implementation
using multiple cameras. Field Programmable Gate Array (FPGA) is a
highly promising tool to be used as a hardware accelerator in many
emerging embedded vision based system. Thus, it is the main
objective of this paper to present an FPGA-based solution of visual
based fall detection to meet stringent real-time requirements with
high accuracy. The hardware architecture of visual based fall
detection which utilizes the pixel locality to reduce memory accesses
is proposed. By exploiting the parallel and pipeline architecture of
FPGA, our hardware implementation of visual based fall detection
using FGPA is able to achieve a performance of 60fps for a series of
video analytical functions at VGA resolutions (640x480). The results
of this work show that FPGA has great potentials and impacts in
enabling large scale vision system in the future healthcare industry
due to its flexibility and scalability.