Abstract: In this study, the evaluation of thermal stability of the
micrometer-sized silica particle reinforced epoxy composite was
carried out through the measurement of thermal expansion coefficient
and Young’s modulus of the specimens. For all the specimens in this
study from the baseline to those containing 50 wt% silica filler, the
thermal expansion coefficients and the Young’s moduli were
gradually decreased down to 20% and increased up to 41%,
respectively. The experimental results were compared with fillervolume-
based simple empirical relations. The experimental results of
thermal expansion coefficients correspond with those of Thomas’s
model which is modified from the rule of mixture. However, the
measured result for Young’s modulus tends to be increased slightly.
The differences in increments of the moduli between experimental and
numerical model data are quite large.
Abstract: The mineral bioflotation represents a viable
alternative for the evaluation of new processes benefit alternative.
The adsorption bacteria on minerals surfaces will depend mainly on
the type of the microorganism as well as of the studied mineral
surface. In the current study, adhesion of S. carnosus on coal was
studied. Several methods were used as: DRX, Fourier Transform
Infra-Red (FTIR) adhesion isotherms and kinetic. The main goal is to
recovery of organic matter by the microflotation process on coal
particles with biological reagent (S. carnosus). Adhesion tests
revealed that adhesion took place after of 8 h at pH 9. The results
suggest that the adhesion of bacteria to solid substrates can be
considered an abiotic physicochemical process that is consequently
governed by bacterial surface properties such as their specific surface
area, hydrophobicity and surface functionalities. The greatest coal
fine flotability was of 75%, after 5 min of flotation.
Abstract: In this paper, strontium ferrite (SrO.6Fe2O3) was
synthesized by the sol-gel auto-combustion process. The thermal
behavior of powder obtained from self-propagating combustion of
initial gel was evaluated by simultaneous differential thermal analysis
(DTA) and thermo gravimetric (TG), from room temperature to
1200°C. The as-burnt powder was calcined at various temperatures
from 700-900°C to achieve the single-phase Sr-ferrite. Phase
composition, morphology and magnetic properties were investigated
using X-ray diffraction (XRD), transmission electron microscopy
(TEM) and vibrating sample magnetometry (VSM) techniques.
Results showed that the single-phase and nano-sized hexagonal
strontium ferrite particles were formed at calcination temperature of
800°C with crystallite size of 27 nm and coercivity of 6238 Oe.
Abstract: The effect of various humidities on process yields and
degrees of crystallinity for spray-dried powders from spray drying of
lactose with humid air in a straight-through system have been
studied. It has been suggested by Williams–Landel–Ferry kinetics
(WLF) that a higher particle temperature and lower glass-transition
temperature would increase the crystallization rate of the particles
during the spray-drying process. Freshly humidified air produced by
a Buchi-B290 spray dryer as a humidifier attached to the main spray
dryer decreased the particle glass-transition temperature (Tg), while
allowing the particle temperature (Tp) to reach higher values by using
an insulated drying chamber. Differential scanning calorimetry
(DSC) and moisture sorption analysis were used to measure the
degree of crystallinity for the spray-dried lactose powders. The
results showed that higher Tp-Tg, as a result of applying humid air,
improved the process yield from 21 ± 4 to 26 ± 2% and crystallinity
of the particles by decreasing the latent heat of crystallization from
43 ± 1 to 30 ± 11 J/g and the sorption peak height from 7.3 ± 0.7% to
6 ± 0.7%.
Abstract: This paper presents a new meta-heuristic bio-inspired
optimization algorithm which is called Cuttlefish Algorithm (CFA).
The algorithm mimics the mechanism of color changing behavior of
the cuttlefish to solve numerical global optimization problems. The
colors and patterns of the cuttlefish are produced by reflected light
from three different layers of cells. The proposed algorithm considers
mainly two processes: reflection and visibility. Reflection process
simulates light reflection mechanism used by these layers, while
visibility process simulates visibility of matching patterns of the
cuttlefish. To show the effectiveness of the algorithm, it is tested with
some other popular bio-inspired optimization algorithms such as
Genetic Algorithms (GA), Particle Swarm Optimization (PSO) and
Bees Algorithm (BA) that have been previously proposed in the
literature. Simulations and obtained results indicate that the proposed
CFA is superior when compared with these algorithms.
Abstract: Phase equilibria of AZ91D Mg alloys for
nonflammable use, containing Ca and Y, were carried out by using
FactSage® and FTLite database, which revealed that solid solution
treatment could be performed at temperatures from 400 to 450oC.
Solid solution treatment of AZ91D Mg alloy without Ca and Y was
successfully conducted at 420oC and supersaturated microstructure
with all beta phase resolved into matrix was obtained. In the case of
AZ91D Mg alloy with some Ca and Y; however, a little amount of
intermetallic particles were observed after solid solution treatment.
After solid solution treatment, each alloy was annealed at temperatures
of 180 and 200oC for time intervals from 1 min to 48 hrs and hardness
of each condition was measured by micro-Vickers method. Peak aging
conditions were deduced as at the temperature of 200oC for 10 hrs.
Abstract: Biological conversion of biomass to methane has
received increasing attention in recent years. Grasses have been
explored for their potential anaerobic digestion to methane. In this
review, extensive literature data have been tabulated and classified.
The influences of several parameters on the potential of these
feedstocks to produce methane are presented. Lignocellulosic
biomass represents a mostly unused source for biogas and ethanol
production. Many factors, including lignin content, crystallinity of
cellulose, and particle size, limit the digestibility of the hemicellulose
and cellulose present in the lignocellulosic biomass. Pretreatments
have used to improve the digestibility of the lignocellulosic biomass.
Each pretreatment has its own effects on cellulose, hemicellulose and
lignin, the three main components of lignocellulosic biomass. Solidstate
anaerobic digestion (SS-AD) generally occurs at solid
concentrations higher than 15%. In contrast, liquid anaerobic
digestion (AD) handles feedstocks with solid concentrations between
0.5% and 15%. Animal manure, sewage sludge, and food waste are
generally treated by liquid AD, while organic fractions of municipal
solid waste (OFMSW) and lignocellulosic biomass such as crop
residues and energy crops can be processed through SS-AD. An
increase in operating temperature can improve both the biogas yield
and the production efficiency, other practices such as using AD
digestate or leachate as an inoculant or decreasing the solid content
may increase biogas yield but have negative impact on production
efficiency. Focus is placed on substrate pretreatment in anaerobic
digestion (AD) as a means of increasing biogas yields using today’s
diversified substrate sources.
Abstract: The emergence of the Semantic Web technology
increases day by day due to the rapid growth of multiple web pages.
Many standard formats are available to store the semantic web data.
The most popular format is the Resource Description Framework
(RDF). Querying large RDF graphs becomes a tedious procedure
with a vast increase in the amount of data. The problem of query
optimization becomes an issue in querying large RDF graphs.
Choosing the best query plan reduces the amount of query execution
time. To address this problem, nature inspired algorithms can be used
as an alternative to the traditional query optimization techniques. In
this research, the optimal query plan is generated by the proposed
SAPSO algorithm which is a hybrid of Simulated Annealing (SA)
and Particle Swarm Optimization (PSO) algorithms. The proposed
SAPSO algorithm has the ability to find the local optimistic result
and it avoids the problem of local minimum. Experiments were
performed on different datasets by changing the number of predicates
and the amount of data. The proposed algorithm gives improved
results compared to existing algorithms in terms of query execution
time.
Abstract: Turbulent flow in complex geometries receives considerable attention due to its importance in many engineering applications. It has been the subject of interest for many researchers. Some of these interests include the design of storm water channels. The design of these channels requires testing through physical models. The main practical limitation of physical models is the so called “scale effect”, that is, the fact that in many cases only primary physical mechanisms can be correctly represented, while secondary mechanisms are often distorted. These observations form the basis of our study, which centered on problems associated with the design of storm water channels near the Dead Sea, in Israel. To help reach a final design decision we used different physical models. Our research showed good coincidence with the results of laboratory tests and theoretical calculations, and allowed us to study different effects of fluid flow in an open channel. We determined that problems of this nature cannot be solved only by means of theoretical calculation and computer simulation. This study demonstrates the use of physical models to help resolve very complicated problems of fluid flow through baffles and similar structures. The study applies these models and observations to different construction and multiphase water flows, among them, those that include sand and stone particles, a significant attempt to bring to the testing laboratory a closer association with reality.
Abstract: This paper deals with advanced state estimation algorithms for estimation of biomass concentration and specific growth rate in a typical fed-batch biotechnological process. This biotechnological process was represented by a nonlinear mass-balance based process model. Extended Kalman Filter (EKF) and Particle Filter (PF) was used to estimate the unmeasured state variables from oxygen uptake rate (OUR) and base consumption (BC) measurements. To obtain more general results, a simplified process model was involved in EKF and PF estimation algorithms. This model doesn’t require any special growth kinetic equations and could be applied for state estimation in various bioprocesses. The focus of this investigation was concentrated on the comparison of the estimation quality of the EKF and PF estimators by applying different measurement noises. The simulation results show that Particle Filter algorithm requires significantly more computation time for state estimation but gives lower estimation errors both for biomass concentration and specific growth rate. Also the tuning procedure for Particle Filter is simpler than for EKF. Consequently, Particle Filter should be preferred in real applications, especially for monitoring of industrial bioprocesses where the simplified implementation procedures are always desirable.
Abstract: A new algorithm based on the lattice Boltzmann method (LBM) is proposed as a potential solver for one-dimensional heat and mass transfer for isothermal carbonization of wood particles. To check the validity of this algorithm, the LBM results have been compared with the published data and a good agreement is obtained. Then, the model is used to study the effect of reactor temperature and particle size on the evolution of the local temperature and mass loss inside the wood particle.
Abstract: Sustainability, being the urgent issue of our time, is
closely related with the innovations in technology. Nanotechnology
(NT), although not a new science, can be regarded relatively a new
science for buildings with brand new materials and applications. This
paper tends to give a research review of current and near future
applications of nanotechnology (NT) for achieving high-performance
and healthy buildings for a sustainable future. In the introduction, the
driving forces for the sustainability of construction industry are
explained. Then, the term NT is defined, and significance of
innovations in NT for a sustainable construction industry is revealed.
After presenting the application areas of NT and nanomaterials for
buildings with a number of cases, challenges in the adoption of this
technology are put forward, and finally the impacts of nanoparticles
and nanomaterials on human health and environment are discussed.
Abstract: Solid lipid nanoparticles (SLNs) have gained great attention for the topical treatment of skin associated fungal infection as they facilitate the skin penetration of loaded drugs. Our work deals with the preparation of nystatin loaded solid lipid nanoparticles (NystSLNs) using the hot homogenization and ultrasonication method. The prepared NystSLNs were characterized in terms of entrapment efficiency, particle size, zeta potential, transmission electron microscopy, differential scanning calorimetry, rheological behavior and in vitro drug release. A stability study for 6 months was performed. A microbiological study was conducted in male rats infected with Candida albicans, by counting the colonies and examining the histopathological changes induced on the skin of infected rats. The results showed that SLNs dispersions are spherical in shape with particle size ranging from 83.26±11.33 to 955.04±1.09 nm. The entrapment efficiencies are ranging from 19.73±1.21 to 72.46±0.66% with zeta potential ranging from -18.9 to -38.8 mV and shear-thinning rheological Behavior. The stability studies done for 6 months showed that nystatin (Nyst) is a good candidate for topical SLN formulations. A least number of colony forming unit/ ml (cfu/ml) was recorded for the selected NystSLN compared to the drug solution and the commercial Nystatin® cream present in the market. It can be fulfilled from this work that SLNs provide a good skin targeting effect and may represent promising carrier for topical delivery of Nyst offering the sustained release and maintaining the localized effect, resulting in an effective treatment of cutaneous fungal infection.
Abstract: DC-DC converters are widely used as reliable power source for many industrial and military applications, computers and electronic devices. Several control methods were developed for DC-DC converters control mostly with asymptotic convergence. Synergetic control (SC) is a proven robust control approach and will be used here in a so called terminal scheme to achieve finite time convergence. Lyapounov synthesis is adopted to assure controlled system stability. Furthermore particle swarm optimization (PSO) algorithm, based on an integral time absolute of error (ITAE) criterion will be used to optimize controller parameters. Simulation of terminal synergetic control of a DC-DC converter is carried out for different operating conditions and results are compared to classic synergetic control performance, that which demonstrate the effectiveness and feasibility of the proposed control method.
Abstract: Polymer composite nano-fibers including (1, 3 wt %)
silver nano-particles have been produced by electrospinning method.
Polyacrylonitrile/N,N-dimethylformamide (PAN/DMF) solution have
been prepared and the amount of silver nitrate have been adjusted to
PAN weight. Silver nano-particles were obtained from reduction of
silver ions into silver nano-particles by chemical reduction by
hydrazine hydroxide (N2H5OH). The different amount of silver salt
was loaded into polymer matrix to obtain polyacrylonitrile composite
nano-fiber containing silver nano-particles. The effect of the amount
of silver nano-particles on the properties of composite nano-fiber web
was investigated. Electrical conductivity, mechanical properties,
thermal properties were examined by Microtest LCR Meter 6370
(0.01 mΩ-100 MΩ), Tensile tester, Differential scanning calorimeter
DSC (Q10) and SEM respectively. Also antimicrobial efficiency test
(ASTM E2149-10) was done against to Staphylococcus aureus
bacteria. It has been seen that breaking strength, conductivity,
antimicrobial effect, enthalpy during cyclization increase by use of
silver nano-particles while the diameter of nano-fiber decreases.
Abstract: In this paper, we present a neural-network (NN) based
approach to represent a nonlinear Tagagi-Sugeno (T-S) system. A
linear differential inclusion (LDI) state-space representation is utilized
to deal with the NN models. Taking advantage of the LDI
representation, the stability conditions and controller design are
derived for a class of nonlinear structural systems. Moreover, the
concept of utilizing the Parallel Particle Swarm Optimization (PPSO)
algorithm to solve the common P matrix under the stability criteria is
given in this paper.
Abstract: In this paper, an analytical study is made for the dynamic behavior of human brain tissue under transient loading. In this analytical model the Mooney-Rivlin constitutive law is coupled with visco-elastic constitutive equations to take into account both the nonlinear and time-dependent mechanical behavior of brain tissue. Five ordinary differential equations representing the relationships of five main parameters (radial stress, circumferential stress, radial strain, circumferential strain, and particle velocity) are obtained by using the characteristic method to transform five partial differential equations (two continuity equations, one motion equation, and two constitutive equations). Analytical expressions of the attenuation properties for spherical wave in brain tissue are analytically derived. Numerical results are obtained based on the five ordinary differential equations. The mechanical responses (particle velocity and stress) of brain are compared at different radii including 5, 6, 10, 15 and 25 mm under four different input conditions. The results illustrate that loading curves types of the particle velocity significantly influences the stress in brain tissue. The understanding of the influence by the input loading cures can be used to reduce the potentially injury to brain under head impact by designing protective structures to control the loading curves types.
Abstract: Nanoscale thermites such as the composite mixture of
nano-sized aluminum and molybdenum trioxide powders possess
several technical advantages such as much higher reaction rate and
shorter ignition delay, when compared to the conventional energetic
formulations made of micron-sized metal and oxidizer particles. In this
study, the self-propagation of combustion wave in compacted pellets
of nanoscale thermite composites is modeled and computationally
investigated by utilizing the activation energy reduction of aluminum
particles due to nanoscale particle sizes. The present computational
model predicts the speed of combustion wave propagation which is
good agreement with the corresponding experiments of thermite
reaction. Also, several characteristics of thermite reaction in nanoscale
composites are discussed including the ignition delay and combustion
wave structures.
Abstract: Ni-based catalysts with different amounts of Na as
promoter from 2 to 6 wt % were prepared by solution combustion
method. The catalytic activity was investigated in syngas methanation
reaction. Carbon oxides conversion and methane selectivity are greatly
influenced by sodium loading. Adding 2 wt% Na remarkably improves
catalytic activity and long-term stability, attributed to its smaller mean
NiO particle size, better distribution, and milder metal-support
interaction. However, excess addition of Na results in deactivation
distinctly due to the blockage of active sites.
Abstract: This work investigates the wear of a steam turbine blade coated with titanium nitride (TiN), and compares to the wear of uncoated blades. The coating is deposited on by physical vapor deposition (PVD) method. The working conditions of the blade were simulated and surface temperature and pressure values as well as flow velocity and flow direction were obtained. This data was used in the finite element wear model developed here in order to predict the wear of the blade. The wear mechanisms considered are erosive wear due to particle impingement and fluid jet, and fatigue wear due to repeated impingement of particles and fluid jet. Results show that the life of the TiN-coated blade is approximately 1.76 times longer than the life of the uncoated one.