Abstract: The textile industry produces highly coloured
effluents containing polar and non-polar compounds. The textile mill
run by the Assam Polyester Co-operative Society Limited (APOL) is
situated at Rangia, about 55 km from Guwahati (26011' N, 91047' E)
in the northern bank of the river Brahmaputra, Assam (India). This
unit was commissioned in June 1988 and started commercial
production in November 1988. The installed capacity of the weaving
unit was 8000 m/day and that of the processing unit was 20,000
m/day. The mill has its own dyeing unit with a capacity of 1500-2000
kg/day. The western side of the mill consists of vast agricultural land
and the far northern and southern side of the mill has scattered human
population. The eastern side of the mill has a major road for
thoroughfare. The mill releases its effluents into the agricultural land
in the western side of the mill. The present study was undertaken to
assess the impact of the textile mill on surface soil quality in and
around the mill with particular reference to Cr, Mn, Ni and Zn.
Surface soil samples, collected along different directions at 200, 500
and 1000 m were digested and the metals were estimated with
Atomic Absorption Spectrophotometer. The metals were found in the
range of: Cr 50.9 – 105.0 mg kg-1, Mn 19.2- 78.6 mg kg-1, Ni 41.9 –
50.6 mg kg-1 and Zn 187.8 – 1095.8 mg kg-1. The study reveals
enrichment of Cr, Mn, Ni and Zn in the soil near the textile mill.
Abstract: Trace element speciation of an integrated soil
amendment matrix was studied with a modified BCR sequential
extraction procedure. The analysis included pseudo-total
concentration determinations according to USEPA 3051A and
relevant physicochemical properties by standardized methods. Based
on the results, the soil amendment matrix possessed neutralization
capacity comparable to commercial fertilizers. Additionally, the
pseudo-total concentrations of all trace elements included in the
Finnish regulation for agricultural fertilizers were lower than the
respective statutory limit values. According to chemical speciation,
the lability of trace elements increased in the following order: Hg <
Cr < Co < Cu < As < Zn < Ni < Pb < Cd < V < Mo < Ba. The
validity of the BCR approach as a tool for chemical speciation was
confirmed by the additional acid digestion phase. Recovery of trace
elements during the procedure assured the validity of the approach
and indicated good quality of the analytical work.
Abstract: Tracing and locating the geographical location of users (Geolocation) is used extensively in todays Internet. Whenever we, e.g., request a page from google we are - unless there was a specific configuration made - automatically forwarded to the page with the relevant language and amongst others, dependent on our location identified, specific commercials are presented. Especially within the area of Network Security, Geolocation has a significant impact. Because of the way the Internet works, attacks can be executed from almost everywhere. Therefore, for an attribution, knowledge of the origination of an attack - and thus Geolocation - is mandatory in order to be able to trace back an attacker. In addition, Geolocation can also be used very successfully to increase the security of a network during operation (i.e. before an intrusion actually has taken place). Similar to greylisting in emails, Geolocation allows to (i) correlate attacks detected with new connections and (ii) as a consequence to classify traffic a priori as more suspicious (thus particularly allowing to inspect this traffic in more detail). Although numerous techniques for Geolocation are existing, each strategy is subject to certain restrictions. Following the ideas of Endo et al., this publication tries to overcome these shortcomings with a combined solution of different methods to allow improved and optimized Geolocation. Thus, we present our architecture for improved Geolocation, by designing a new algorithm, which combines several Geolocation techniques to increase the accuracy.
Abstract: Reliable secure multicast communication in mobile
adhoc networks is challenging due to its inherent characteristics of
infrastructure-less architecture with lack of central authority, high
packet loss rates and limited resources such as bandwidth, time and
power. Many emerging commercial and military applications require
secure multicast communication in adhoc environments. Hence key
management is the fundamental challenge in achieving reliable
secure communication using multicast key distribution for mobile
adhoc networks. Thus in designing a reliable multicast key
distribution scheme, reliability and congestion control over
throughput are essential components. This paper proposes and
evaluates the performance of an enhanced optimized multicast cluster
tree algorithm with destination sequenced distance vector routing
protocol to provide reliable multicast key distribution. Simulation
results in NS2 accurately predict the performance of proposed
scheme in terms of key delivery ratio and packet loss rate under
varying network conditions. This proposed scheme achieves
reliability, while exhibiting low packet loss rate with high key
delivery ratio compared with the existing scheme.
Abstract: A feasibility study for the design and construction of a
pilot plant for the extraction of castor oil in South Africa was
conducted. The study emphasized the four critical aspects of project
feasibility analysis, namely technical, financial, market and
managerial aspects. The technical aspect involved research on
existing oil extraction technologies, namely: mechanical pressing and
solvent extraction, as well as assessment of the proposed production
site for both short and long term viability of the project. The site is
on the outskirts of Nkomazi village in the Mpumalanga province,
where connections for water and electricity are currently underway,
potential raw material supply proves to be reliable since the province
is known for its commercial farming. The managerial aspect was
evaluated based on the fact that the current producer of castor oil will
be fully involved in the project while receiving training and technical
assistance from Sasol Technology, the TSC and SEDA. Market and
financial aspects were evaluated and the project was considered
financially viable with a Net Present Value (NPV) of R2 731 687 and
an Internal Rate of Return (IRR) of 18% at an annual interest rate of
10.5%. The payback time is 6years for analysis over the first 10
years with a net income of R1 971 000 in the first year. The project
was thus found to be feasible with high chance of success while
contributing to socio-economic development. It was recommended
for lab tests to be conducted to establish process kinetics that would
be used in the initial design of the plant.
Abstract: Trends in business intelligence, e-commerce and
remote access make it necessary and practical to store data in
different ways on multiple systems with different operating systems.
As business evolve and grow, they require efficient computerized
solution to perform data update and to access data from diverse
enterprise business applications. The objective of this paper is to
demonstrate the capability of DTS [1] as a database solution for
automatic data transfer and update in solving business problem. This
DTS package is developed for the sales of variety of plants and
eventually expanded into commercial supply and landscaping
business. Dimension data modeling is used in DTS package to
extract, transform and load data from heterogeneous database
systems such as MySQL, Microsoft Access and Oracle that
consolidates into a Data Mart residing in SQL Server. Hence, the
data transfer from various databases is scheduled to run automatically
every quarter of the year to review the efficient sales analysis.
Therefore, DTS is absolutely an attractive solution for automatic data
transfer and update which meeting today-s business needs.
Abstract: One of the major disadvantages of the minimally
invasive surgery (MIS) is the lack of tactile feedback to the surgeon.
In order to identify and avoid any damage to the grasped complex
tissue by endoscopic graspers, it is important to measure the local
softness of tissue during MIS. One way to display the measured
softness to the surgeon is a graphical method. In this paper, a new
tactile sensor has been reported. The tactile sensor consists of an
array of four softness sensors, which are integrated into the jaws of a
modified commercial endoscopic grasper. Each individual softness
sensor consists of two piezoelectric polymer Polyvinylidene Fluoride
(PVDF) films, which are positioned below a rigid and a compliant
cylinder. The compliant cylinder is fabricated using a micro molding
technique. The combination of output voltages from PVDF films is
used to determine the softness of the grasped object. The theoretical
analysis of the sensor is also presented.
A method has been developed with the aim of reproducing the
tactile softness to the surgeon by using a graphical method. In this
approach, the proposed system, including the interfacing and the data
acquisition card, receives signals from the array of softness sensors.
After the signals are processed, the tactile information is displayed
by means of a color coding method. It is shown that the degrees of
softness of the grasped objects/tissues can be visually differentiated
and displayed on a monitor.
Abstract: The pulp and paper mill effluent is one of the high
polluting effluent amongst the effluents obtained from polluting
industries. All the available methods for treatment of pulp and paper
mill effluent have certain drawbacks. The coagulation is one of the
cheapest process for treatment of various organic effluents. Thus, the
removal of chemical oxygen demand (COD) and colour of paper mill
effluent is studied using coagulation process. The batch coagulation
process was performed using various coagulants like: aluminium
chloride, poly aluminium chloride and copper sulphate. The initial
pH of the effluent (Coagulation pH) has tremendous effect on COD
and colour removal. Poly aluminium chloride (PAC) as coagulant
reduced COD to 84 % and 92 % of colour was removed at an
optimum pH 5 and coagulant dose of 8 ml l-1. With aluminium
chloride at an optimum pH = 4 and coagulant dose of 5 g l-1, 74 %
COD and 86 % colour removal were observed. The results using
copper sulphate as coagulant (a less commercial coagulant) were
encouraging. At an optimum pH 6 and mass loading of 5 g l-1, 76 %
COD reduction and 78 % colour reduction were obtained. It was also
observed that after addition of coagulant, the pH of the effluent
decreases. The decrease in pH was highest for AlCl3, which was
followed by PAC and CuSO4. Significant amount of COD reductions
was obtained by coagulation process. Since the coagulation process
is the first stage for treatment of effluent and some of the coagulant
cations usually remain in the treated effluents. Thus, cation like
copper may be one of the good catalyst for second stage of treatment
process like wet oxidation. The copper has been found to be good
oxidation catalyst then iron and aluminum.
Abstract: Now a days, a significant part of commercial and governmental organisations like museums, cultural organizations, libraries, commercial enterprises, etc. invest intensively in new technologies for image digitization, digital libraries, image archiving and retrieval. Hence image authorization, authentication and security has become prime need. In this paper, we present a semi-fragile watermarking scheme for color images. The method converts the host image into YIQ color space followed by application of orthogonal dual domains of DCT and DWT transforms. The DCT helps to separate relevant from irrelevant image content to generate silent image features. DWT has excellent spatial localisation to help aid in spatial tamper characterisation. Thus image adaptive watermark is generated based of image features which allows the sharp detection of microscopic changes to locate modifications in the image. Further, the scheme utilises the multipurpose watermark consisting of soft authenticator watermark and chrominance watermark. Which has been proved fragile to some predefined processing like intentinal fabrication of the image or forgery and robust to other incidental attacks caused in the communication channel.
Abstract: Efficient luminescence is reported for the first time in Eu2+ activated double Chlorides A2BCl4 (A=Alkali metal, B=Alkaline earth element). A simple wet-chemical preparation is described. Emission intensities are comparable to that of the commercial phosphor. Excitation covers near UV region. These phosphors may be useful for applications like solid state lighting, scintillation detectors and X-ray storage using photo-stimulable phosphors.
Abstract: Saturated hydraulic conductivity is one of the soil
hydraulic properties which is widely used in environmental studies
especially subsurface ground water. Since, its direct measurement is
time consuming and therefore costly, indirect methods such as
pedotransfer functions have been developed based on multiple linear
regression equations and neural networks model in order to estimate
saturated hydraulic conductivity from readily available soil
properties e.g. sand, silt, and clay contents, bulk density, and organic
matter. The objective of this study was to develop neural networks
(NNs) model to estimate saturated hydraulic conductivity from
available parameters such as sand and clay contents, bulk density,
van Genuchten retention model parameters (i.e. r
θ , α , and n) as well
as effective porosity. We used two methods to calculate effective
porosity: : (1) eff s FC φ =θ -θ , and (2) inf φ =θ -θ eff s , in which s
θ is
saturated water content, FC θ is water content retained at -33 kPa
matric potential, and inf θ is water content at the inflection point.
Total of 311 soil samples from the UNSODA database was divided
into three groups as 187 for the training, 62 for the validation (to
avoid over training), and 62 for the test of NNs model. A commercial
neural network toolbox of MATLAB software with a multi-layer
perceptron model and back propagation algorithm were used for the
training procedure. The statistical parameters such as correlation
coefficient (R2), and mean square error (MSE) were also used to
evaluate the developed NNs model. The best number of neurons in
the middle layer of NNs model for methods (1) and (2) were
calculated 44 and 6, respectively. The R2 and MSE values of the test
phase were determined for method (1), 0.94 and 0.0016, and for
method (2), 0.98 and 0.00065, respectively, which shows that method
(2) estimates saturated hydraulic conductivity better than method (1).
Abstract: This study presents a simulation model for converting coal to methanol, based on gasification technology with the commercial chemical process simulator, Pro/II® V8.1.1. The methanol plant consists of air separation unit (ASU), gasification unit, gas clean-up unit, and methanol synthetic unit. The clean syngas is produced with the first three operating units, and the model has been verified with the reference data from United States Environment Protection Agency. The liquid phase methanol (LPMEOHTM) process is adopted in the methanol synthetic unit. Clean syngas goes through gas handing section to reach the reaction requirement, reactor loop/catalyst to generate methanol, and methanol distillation to get desired purity over 99.9 wt%. The ratio of the total energy combined with methanol and dimethyl ether to that of feed coal is 78.5% (gross efficiency). The net efficiency is 64.2% with the internal power consumption taken into account, based on the assumption that the efficiency of electricity generation is 40%.
Abstract: A number of previous studies were rarely considered
the effects of transient non-uniform balloon expansion on evaluation
of the properties and behaviors of stents during stent expansion, nor
did they determine parameters to maximize the performances driven
by mechanical characteristics. Therefore, in order to fully understand
the mechanical characteristics and behaviors of stent, it is necessary to
consider a realistic modeling of transient non-uniform balloon-stent
expansion. The aim of the study is to propose design parameters
capable of improving the ability of vascular stent through a
comparative study of seven commercial stents using finite element
analyses of a realistic transient non-uniform balloon-stent expansion
process. In this study, seven representative commercialized stents were
evaluated by finite element (FE) analysis in terms of the criteria based
on the itemized list of Food and Drug Administration (FDA) and
European Standards (prEN). The results indicate that using stents
composed of opened unit cells connected by bend-shaped link
structures and controlling the geometrical and morphological features
of the unit cell strut or the link structure at the distal ends of stent may
improve mechanical characteristics of stent. This study provides a
better method at the realistic transient non-uniform balloon-stent
expansion by investigating the characteristics, behaviors, and
parameters capable of improving the ability of vascular stent.
Abstract: The objective of this work was to investigate flow
properties of powdered infant formula samples. Samples were
purchased at a local pharmacy and differed in composition. Lactose
free infant formula, gluten free infant formula and infant formulas
containing dietary fibers and probiotics were tested and compared
with a regular infant formula sample which did not contain any of
these supplements. Particle size and bulk density were determined
and their influence on flow properties was discussed. There were no
significant differences in bulk densities of the samples, therefore the
connection between flow properties and bulk density could not be
determined. Lactose free infant formula showed flow properties
different to standard supplement-free sample. Gluten free infant
formula with addition of probiotic microorganisms and dietary fiber
had the narrowest particle size distribution range and exhibited the
best flow properties. All the other samples exhibited the same
tendency of decreasing compaction coefficient with increasing flow
speed, which means they all become freer flowing with higher flow
speeds.
Abstract: Haptics has been used extensively in many applications especially in human machine interaction and virtual reality systems. Haptic technology allows user to perceive virtual reality as in real world. However, commercially available haptic devices are expensive and may not be suitable for educational purpose. This paper describes the design and development of a low cost haptic knob, with only one degree of freedom, for use in rehabilitation or training hand pronation and supination. End-effectors can be changed to suit different applications or variation in hand sizes and hand orientation.
Abstract: It has been recognized that due to the autonomy and
heterogeneity, of Web services and the Web itself, new approaches
should be developed to describe and advertise Web services. The
most notable approaches rely on the description of Web services
using semantics. This new breed of Web services, termed semantic
Web services, will enable the automatic annotation, advertisement,
discovery, selection, composition, and execution of interorganization
business logic, making the Internet become a common
global platform where organizations and individuals communicate
with each other to carry out various commercial activities and to
provide value-added services. This paper deals with two of the
hottest R&D and technology areas currently associated with the Web
– Web services and the semantic Web. It describes how semantic
Web services extend Web services as the semantic Web improves the
current Web, and presents three different conceptual approaches to
deploying semantic Web services, namely, WSDL-S, OWL-S, and
WSMO.
Abstract: This research work proposed a study of fruit bruise detection by means of a biospeckle method, selecting the papaya fruit (Carica papaya) as testing body. Papaya is recognized as a fruit of outstanding nutritional qualities, showing high vitamin A content, calcium, carbohydrates, exhibiting high popularity all over the world, considering consumption and acceptability. The commercialization of papaya faces special problems which are associated to bruise generation during harvesting, packing and transportation. Papaya is classified as climacteric fruit, permitting to be harvested before the maturation is completed. However, by one side bruise generation is partially controlled once the fruit flesh exhibits high mechanical firmness. By the other side, mechanical loads can set a future bruise at that maturation stage, when it can not be detected yet by conventional methods. Mechanical damages of fruit skin leave an entrance door to microorganisms and pathogens, which will cause severe losses of quality attributes. Traditional techniques of fruit quality inspection include total soluble solids determination, mechanical firmness tests, visual inspections, which would hardly meet required conditions for a fully automated process. However, the pertinent literature reveals a new method named biospeckle which is based on the laser reflectance and interference phenomenon. The laser biospeckle or dynamic speckle is quantified by means of the Moment of Inertia, named after its mechanical counterpart due to similarity between the defining formulae. Biospeckle techniques are able to quantify biological activities of living tissues, which has been applied to seed viability analysis, vegetable senescence and similar topics. Since the biospeckle techniques can monitor tissue physiology, it could also detect changes in the fruit caused by mechanical damages. The proposed technique holds non invasive character, being able to generate numerical results consistent with an adequate automation. The experimental tests associated to this research work included the selection of papaya fruit at different maturation stages which were submitted to artificial mechanical bruising tests. Damages were visually compared with the frequency maps yielded by the biospeckle technique. Results were considered in close agreement.
Abstract: Fluid flow in cylinders of elliptic cross-section was investigated. Fluid used is Liquefied petroleum gas (LPG). LPG found in Nigeria contains majorly butane with percentages of propane. Commercial available code FLUENT which uses finite volume method was used to solve fluid flow governing equations. There has been little attention paid to fluid flow in cylindrical elliptic pipes. The present work aims to predict the LPG gas flow in cylindrical pipes of elliptic cross-section. Results of flow parameters of velocity and pressure distributions are presented. Results show that the pressure drop in elliptic pipes is higher than circular pipe of the same cross-sectional area. This is an important result as the pressure drop is related to the pump power needed to drive the flow. Results show that the velocity increases towards centre of the pipe as the flow moves downstream, and also increases towards the outlet of the pipe.
Abstract: This paper presents a study of laminar to turbulent transition on a profile specifically designed for wind turbine blades, the DU91-W2-250, which belongs to a class of wind turbine dedicated airfoils, developed by Delft University of Technology. A comparison between the experimental behavior of the airfoil studied at Delft wind tunnel and the numerical predictions of the commercial CFD solver ANSYS FLUENT® has been performed. The prediction capabilities of the Spalart-Allmaras turbulence model and of the γ-θ Transitional model have been tested. A sensitivity analysis of the numerical results to the spatial domain discretization has also been performed using four different computational grids, which have been created using the mesher GAMBIT®. The comparison between experimental measurements and CFD results have allowed to determine the importance of the numerical prediction of the laminar to turbulent transition, in order not to overestimate airfoil friction drag due to a fully turbulent-regime flow computation.
Abstract: The strawberry jam is rich in bioactive compounds. It
is economically and commercially important and widely consumed.
Different strawberries cultivars can be used for its preparation,
however, a careful selection should be performed to guarantee the
preservation of bioactive compounds during jam storage. Two
strawberry cultivars (Camarosa and American 13) were analyzed by
HPLC, three anthocyanins: cyanidin-3-glucoside, pelargonidin-3-
glucoside and pelargonidin-3-rutinoside were quantified. Camarosa
strawberries presented significantly higher concentration of
anthocyanins (p