Abstract: The effect of carbon nanofibers (CNFs) on the
electrical properties of Poly(vinylidene fluoride-hexafluoropropylene)
(P(VdF-HFP)) based gel polymer electrolytes has been investigated
in the present work. The length and diameter ranges of CNFs used in
the present work are 5-50 μm and 200-600 nm respectively. The
nanocomposite gel polymer electrolytes have been synthesized by
solution casting technique with varying CNFs content in terms of
weight percentage. Electrochemical impedance analysis demonstrates
that the reinforcement of carbon nanofibers significantly enhances the
ionic conductivity of the polymer electrolyte. The decrease of
crystallinity of P(VdF-HFP) due the addition of CNFs has been
confirmed by X-ray diffraction (XRD). The interaction of CNFs with
various constituents of nanocomposite gel polymer electrolytes has
been assessed by Fourier Transform Infrared (FTIR) spectroscopy.
Moreover CNFs added gel polymer electrolytes offer superior
thermal stability as compared to that of CNFs free electrolytes as
confirmed by Thermogravimetric analysis (TGA).
Abstract: This paper considers the design of Dual Proportional-
Integral (DPI) Load Frequency Control (LFC), using gravitational
search algorithm (GSA). The design is carried out for nonlinear
hydrothermal power system where generation rate constraint (GRC)
and governor dead band are considered. Furthermore, time delays
imposed by governor-turbine, thermodynamic process, and
communication channels are investigated. GSA is utilized to search
for optimal controller parameters by minimizing a time-domain based
objective function. GSA-based DPI has been compared to Ziegler-
Nichols based PI, and Genetic Algorithm (GA) based PI controllers
in order to demonstrate the superior efficiency of the proposed
design. Simulation results are carried for a wide range of operating
conditions and system parameters variations.
Abstract: Carefully scheduling the operations of pumps can be
resulted to significant energy savings. Schedules can be defined
either implicit, in terms of other elements of the network such as tank
levels, or explicit by specifying the time during which each pump is
on/off. In this study, two new explicit representations based on timecontrolled
triggers were analyzed, where the maximum number of
pump switches was established beforehand, and the schedule may
contain fewer switches than the maximum. The optimal operation of
pumping stations was determined using a Jumping Particle Swarm
Optimization (JPSO) algorithm to achieve the minimum energy cost.
The model integrates JPSO optimizer and EPANET hydraulic
network solver. The optimal pump operation schedule of VanZyl
water distribution system was determined using the proposed model
and compared with those from Genetic and Ant Colony algorithms.
The results indicate that the proposed model utilizing the JPSO
algorithm is a versatile management model for the operation of realworld
water distribution system.
Abstract: The moisture content of densified biomass is a
limiting parameter influencing the quality of this solid biofuel. It
influences its calorific value, density, mechanical strength and
dimensional stability as well as affecting its production process. This
paper deals with experimental research into the effect of moisture
content of the densified material on the final quality of biofuel in the
form of logs (briquettes or pellets). Experiments based on the singleaxis
densification of the spruce sawdust were carried out with a
hydraulic piston press (piston and die), where the densified logs were
produced at room temperature. The effect of moisture content on the
qualitative properties of the logs, including density, change of
moisture, expansion and physical changes, and compressive and
impact resistance were studied. The results show the moisture ranges
required for producing good-quality logs. The experiments were
evaluated and the moisture content of the tested material was
optimized to achieve the optimum value for the best quality of the
solid biofuel. The dense logs also have high-energy content per unit
volume. The research results could be used to develop and optimize
industrial technologies and machinery for biomass densification to
achieve high quality solid biofuel.
Abstract: The current study aims to highlight the loading
characteristics impact on the time evolution (focusing particularly on
long term effects) of the deformation of realized reinforced concrete
beams. Namely the tension stiffening code provisions (i.e. within
Eurocode 2) are reviewed with a clear intention to reassess their
operational value and predicting capacity. In what follows the
experimental programme adopted along with some preliminary
findings and numerical modeling attempts are presented. For a range of long slender reinforced concrete simply supported
beams (4200 mm) constant static sustained and repeated cyclic
loadings were applied mapping the time evolution of deformation.
All experiments were carried out at the Heavy Structures Lab of the
University of Leeds. During tests the mid-span deflection, creep
coefficient and shrinkage strains were monitored for duration of 90
days. The obtained results are set against the values predicted by
Eurocode 2 and the tools within an FE commercial package (i.e.
Midas FEA) to yield that existing knowledge and practise is at times
over-conservative.
Abstract: In VLSI, testing plays an important role. Major
problem in testing are test data volume and test power. The important
solution to reduce test data volume and test time is test data
compression. The Proposed technique combines the bit maskdictionary
and 2n pattern run length-coding method and provides a
substantial improvement in the compression efficiency without
introducing any additional decompression penalty. This method has
been implemented using Mat lab and HDL Language to reduce test
data volume and memory requirements. This method is applied on
various benchmark test sets and compared the results with other
existing methods. The proposed technique can achieve a compression
ratio up to 86%.
Abstract: This paper seeks to assess the implications of bank
consolidation on lending, which largely determine the survival and
performance of small and medium scale enterprises and in turn the
development of the Nigerian economy. Ordinary least square
technique, correlation matrix test and Granger –causality test were
employed to measure the extent to which lending to small and
medium scale enterprises were influenced. The result showed that
bank deposit (BD) impacted on lending to small and medium scale
enterprises. Commercial and merchant bank lending rate had
statistically insignificant effect on the dependent variable. There is a
shift of focus by commercial banks from small and medium scale
enterprises (small customers) to major investors (big customers).
While micro finance banks work hard at providing funds to small and
medium scale entrepreneurs, their capacity to meet the needs of these
entrepreneurs is constrained. The capital and deposits of micro
finance bank should be boosted in order to effectively support small
and medium scale enterprises through loans.
Abstract: Drought is one of the most serious problems posing a
grave threat to cereals production including maize. Maize
improvement in drought-stress tolerance poses a great challenge as
the global need for food and bio-energy increases. Thus, the current
study was planned to explore the variations and determine the
performance of target traits of maize hybrids at grain growth stage
under drought conditions during 2014 under Adana, Mediterranean
climate conditions, Turkey. Maize hybrids (Sancia, Indaco,
71May69, Aaccel, Calgary, 70May82, 72May80) were evaluated
under (irrigated and water stress). Results revealed that, grain yield
and yield traits had a negative effects because of water stress
conditions compared with the normal irrigation. As well as, based on
the result under normal irrigation, the maximum biological yield and
harvest index were recorded. According to the differences among
hybrids were found that, significant differences were observed among
hybrids with respect to yield and yield traits under current research. Based on the results, grain weight had more effect on grain yield
than grain number during grain filling growth stage under water
stress conditions. In this concern, according to low drought
susceptibility index (less grain yield losses), the hybrid (Indaco) was
more stable in grain number and grain weight. Consequently, it may
be concluded that this hybrid would be recommended for use in the
future breeding programs for production of drought tolerant hybrids.
Abstract: Tamil handwritten document is taken as a key source
of data to identify the writer. Tamil is a classical language which has
247 characters include compound characters, consonants, vowels and
special character. Most characters of Tamil are multifaceted in
nature. Handwriting is a unique feature of an individual. Writer may
change their handwritings according to their frame of mind and this
place a risky challenge in identifying the writer. A new
discriminative model with pooled features of handwriting is proposed
and implemented using support vector machine. It has been reported
on 100% of prediction accuracy by RBF and polynomial kernel based
classification model.
Abstract: Oxygen Reduction Reaction (ORR) performance of
iron and nitrogen co-doped porous carbon nanoparticles (Fe-NPC)
with various physical and (electro) chemical properties have been
investigated. Fe-NPC nanoparticles are synthesized via a facile
soft-templating procedure by using Iron (III) chloride hexa-hydrate as
iron precursor and aminophenol-formaldehyde resin as both carbon
and nitrogen precursor. Fe-NPC nanoparticles shows high surface area
(443.83 m2g-1), high pore volume (0.52 m3g-1), narrow mesopore size
distribution (ca. 3.8 nm), high conductivity (IG/ID=1.04), high kinetic
limiting current (11.71 mAcm-2) and more positive onset potential
(-0.106 V) compared to metal-free NPC nanoparticles (-0.295V)
which make it high efficient ORR metal-free catalysts in alkaline
solution. This study may pave the way of feasibly designing iron and
nitrogen containing carbon materials (Fe-N-C) for highly efficient
oxygen reduction electro-catalysis.
Abstract: One of the most important challenging factors in
medical images is nominated as noise. Image denoising refers to the
improvement of a digital medical image that has been infected by
Additive White Gaussian Noise (AWGN). The digital medical image
or video can be affected by different types of noises. They are
impulse noise, Poisson noise and AWGN. Computed tomography
(CT) images are subjects to low quality due to the noise. Quality of
CT images is dependent on absorbed dose to patients directly in such
a way that increase in absorbed radiation, consequently absorbed
dose to patients (ADP), enhances the CT images quality. In this
manner, noise reduction techniques on purpose of images quality
enhancement exposing no excess radiation to patients is one the
challenging problems for CT images processing. In this work, noise
reduction in CT images was performed using two different
directional 2 dimensional (2D) transformations; i.e., Curvelet and
Contourlet and Discrete Wavelet Transform (DWT) thresholding
methods of BayesShrink and AdaptShrink, compared to each other
and we proposed a new threshold in wavelet domain for not only
noise reduction but also edge retaining, consequently the proposed
method retains the modified coefficients significantly that result good
visual quality. Data evaluations were accomplished by using two
criterions; namely, peak signal to noise ratio (PSNR) and Structure
similarity (Ssim).
Abstract: This paper describes how to dimension the electric
components of a 48V hybrid system considering real customer use.
Furthermore, it provides information about savings in energy and
CO2 emissions by a customer-tailored 48V hybrid. Based on measured customer profiles, the electric units such as the
electric motor and the energy storage are dimensioned. Furthermore,
the CO2 reduction potential in real customer use is determined
compared to conventional vehicles. Finally, investigations are carried
out to specify the topology design and preliminary considerations in
order to hybridize a conventional vehicle with a 48V hybrid system.
The emission model results from an empiric approach also taking into
account the effects of engine dynamics on emissions. We analyzed
transient engine emissions during representative customer driving
profiles and created emission meta models. The investigation showed
a significant difference in emissions when simulating realistic
customer driving profiles using the created verified meta models
compared to static approaches which are commonly used for vehicle
simulation.
Abstract: A sliding door system is used in commercial vehicles
and passenger cars to allow a larger unobstructed access to the
interior for loading and unloading. The movement of a sliding door
on vehicle body is ensured by mechanisms and tracks having special
cross-section which is manufactured by roll forming and stretch
bending process. There are three tracks and three mechanisms which
are called upper, central and lower on a sliding door system. There
are static requirements as strength on different directions, rigidity for
mechanisms, door drop off, door sag; dynamic requirements as high
energy slam opening-closing and durability requirement to validate
these products. In addition, there is a kinematic requirement to find
out force values from door handle during manual operating. In this
study, finite element analysis and physical test results which are
realized for sliding door systems will be shared comparatively.
Abstract: Ultraviolet photocatalytic oxidation (UV-PCO)
technology has been recommended as a green approach to health
indoor environment when it is integrated into mechanical ventilation
systems for inorganic and organic compounds removal as well as
energy saving due to less outdoor air intakes. Although much research
has been devoted to UV-PCO, limited information is available on the
UV-PCO behavior tested by the mixtures in literature. This project
investigated UV-PCO performance and by-product generation using a
single and a mixture of acetone and MEK at 100 ppb each in a
single-pass duct system in an effort to obtain knowledge associated
with competitive photochemical reactions involved in. The
experiments were performed at 20 % RH, 22 °C, and a gas flow rate of
128 m3/h (75 cfm). Results show that acetone and MEK mutually
reduced each other’s PCO removal efficiency, particularly negative
removal efficiency for acetone. These findings were different from
previous observation of facilitatory effects on the adsorption of
acetone and MEK on photocatalyst surfaces.
Abstract: In Automotive Industry, sliding door systems that are
also used as body closures are safety members. Extreme product tests
are realized to prevent failures in design process, but these tests
realized experimentally result in high costs. Finite element analysis is
an effective tool used for design process. These analyses are used
before production of prototype for validation of design according to
customer requirement. In result of this, substantial amount of time
and cost is saved. Finite element model is created for geometries that are designed in
3D CAD programs. Different element types as bar, shell and solid,
can be used for creating mesh model. Cheaper model can be created
by selection of element type, but combination of element type that
was used in model, number and geometry of element and degrees of
freedom affects the analysis result. Sliding door system is a good
example which used these methods for this study. Structural analysis
was realized for sliding door mechanism by using FE models. As
well, physical tests that have same boundary conditions with FE
models were realized. Comparison study for these element types,
were done regarding test and analyses results then optimum
combination was achieved.
Abstract: Damaturu is the capital of Yobe State in northeastern
Nigeria where civic amenities and facilities are not adequate even
after 24 years of its existence. The volatile security and political
situations are most significant causes for the same. The basic facility
for the citizens in terms of drinking water and electricity are not
available. For the drinking water, they have to rely on personal
boreholes or the filtered borehole waters available in packaged
sachets in market. The present study is concerned with environmental
impact of indiscriminate disposal of drinking synthetic polythene
water sachets in Damaturu. The sachet water is popularly called as
“pure water”, but its purity is questionable. Increased production and
consumption of sachet water has led to indiscriminate dumping and
disposal of empty sachets leading to serious environmental threat.
The evidence of this is seen for sachets littering the streets and the
drainages blocked by ‘blocks’ of water sachet waste. Sachet water
gained much popularity in Nigeria because the product is convenient
for use, affordable and economically viable. The present study aims
to find out the solution to this environmental problem. The fieldbased
study has found some significant factors that cause
environmental and socio economic effect due to this. Some
recommendations have been made based on research findings
regarding sustainable waste management, recycling and re-use of the
non-biodegradable products in society.
Abstract: In this study, failure analysis of pipe system at a micro
hydroelectric power plant is investigated. Failure occurred at the pipe
system in the powerhouse during shut down operation of the water
flow by a valve. This locking had caused a sudden shock wave, also
called “Water-hammer effect”, resulting in noise and inside pressure
increase. After visual investigation of the effect of the shock wave on
the system, a circumference crack was observed at the pipe flange
weld region. To establish the reason for crack formation, calculations
of pressure and stress values at pipe, flange and welding seams were
carried out and concluded that safety factor was high (2.2), indicating
that no faulty design existed. By further analysis, pipe system and
hydroelectric power plant was examined. After observations it is
determined that the plant did not include a ventilation nozzle (air
trap), that prevents the system of sudden pressure increase inside the
pipes which is caused by water-hammer effect. Analyses were carried
out to identify the influence of water-hammer effect on inside
pressure increase and it was concluded that, according Jowkowsky’s
equation, shut down time is effective on inside pressure increase. The
valve closing time was uncertain but by a shut down time of even one
minute, inside pressure would increase by 7.6 bar (working pressure
was 34.6 bar). Detailed investigations were also carried out on the
assembly of the pipe-flange system by considering technical
drawings. It was concluded that the pipe-flange system was not
installed according to the instructions. Two of five weld seams were
not applied and one weld was carried out faulty. This incorrect and
inadequate weld seams resulted in; insufficient connection of the pipe
to the flange constituting a strong notch effect at weld seam regions,
increase in stress values and the decrease of strength and safety
factor.
Abstract: Nitrification is essential to biological processes
designed to remove ammonia and/or total nitrogen. It removes excess
nitrogenous compound in wastewater which could be very toxic to
the aquatic fauna or cause serious imbalance of such aquatic
ecosystem. Efficient nitrification is linked to an in-depth knowledge
of the structure and dynamics of the nitrifying community structure
within the wastewater treatment systems. In this study, molecular
technique was employed for characterizing the microbial structure of
activated sludge [ammonia oxidizing bacteria (AOB) and nitrite
oxidizing bacteria (NOB)] in a municipal wastewater treatment with
intention of linking it to the plant efficiency. PCR based phylogenetic
analysis was also carried out. The average operating and
environmental parameters as well as specific nitrification rate of plant
was investigated during the study. During the investigation the average temperature was 23±1.5oC.
Other operational parameters such as mixed liquor suspended solids
and chemical oxygen demand inversely correlated with ammonia
removal. The dissolved oxygen level in the plant was constantly
lower than the optimum (between 0.24 and 1.267 mg/l) during this
study. The plant was treating wastewater with influent ammonia
concentration of 31.69 and 24.47 mg/L. The influent flow rates
(ML/Day) was 96.81 during period. The dominant nitrifiers include:
Nitrosomonas spp. Nitrobacter spp. and Nitrospira spp. The AOB
had correlation with nitrification efficiency and temperature. This
study shows that the specific ammonia oxidizing rate and the specific
nitrate formation rates can serve as good indicator of the plant overall
nitrification performance.
Abstract: This study aims to increase understanding of the
transition of business models in servitization. The significance of
service in all business has increased dramatically during the past
decades. Service-dominant logic (SDL) describes this change in the
economy and questions the goods-dominant logic on which business
has primarily been based in the past. A business model canvas is one
of the most cited and used tools in defining end developing business
models. The starting point of this paper lies in the notion that the
traditional business model canvas is inherently goods-oriented and
best suits for product-based business. However, the basic differences
between goods and services necessitate changes in business model
representations when proceeding in servitization. Therefore, new
knowledge is needed on how the conception of business model and
the business model canvas as its representation should be altered in
servitized firms in order to better serve business developers and interfirm
co-creation. That is to say, compared to products, services are
intangible and they are co-produced between the supplier and the
customer. Value is always co-created in interaction between a
supplier and a customer, and customer experience primarily depends
on how well the interaction succeeds between the actors. The role of
service experience is even stronger in service business compared to
product business, as services are co-produced with the customer. This paper provides business model developers with a service
business model canvas, which takes into account the intangible,
interactive, and relational nature of service. The study employs a
design science approach that contributes to theory development via
design artifacts. This study utilizes qualitative data gathered in
workshops with ten companies from various industries. In particular,
key differences between Goods-dominant logic (GDL) and SDLbased
business models are identified when an industrial firm
proceeds in servitization. As the result of the study, an updated version of the business
model canvas is provided based on service-dominant logic. The
service business model canvas ensures a stronger customer focus and
includes aspects salient for services, such as interaction between
companies, service co-production, and customer experience. It can be
used for the analysis and development of a current service business
model of a company or for designing a new business model. It
facilitates customer-focused new service design and service
development. It aids in the identification of development needs, and
facilitates the creation of a common view of the business model.
Therefore, the service business model canvas can be regarded as a
boundary object, which facilitates the creation of a common
understanding of the business model between several actors involved.
The study contributes to the business model and service business
development disciplines by providing a managerial tool for
practitioners in service development. It also provides research insight
into how servitization challenges companies’ business models.
Abstract: This paper aims to study the heat transfer and fluid
flow characteristics of nanofluids used in spray cooling systems. The
effect of spray height, type of nanofluids and concentration of
nanofluids are numerically investigated. Five different nanofluids
such as AgH2O, Al2O3, CuO, SiO2 and TiO2 with volume fraction
range of 0.5% to 2.5% are used. The results revealed that the heat
transfer performance decreases as spray height increases. It is found
that TiO2 has the highest transfer coefficient among other nanofluids.
In dilute spray conditions, low concentration of nanofluids is
observed to be more effective in heat removal in a spray cooling
system.