Abstract: The detection of environmental gases, 12CO2, 13CO2,
and CH4, using near-infrared semiconductor lasers with a short
laser path length is studied by means of wavelength-modulation
spectroscopy. The developed system is compact and has high
sensitivity enough to detect the absorption peaks of isotopic 13CO2
of a 3-% CO2 gas at 2 μm with a path length of 2.4 m, where
its peak size is two orders of magnitude smaller than that of the
ordinary 12CO2 peaks. In addition, the detection of 12CO2 peaks of
a 385-ppm (0.0385-%) CO2 gas in the air is made at 2 μm with a
path length of 1.4 m. Furthermore, in pursuing the detection of an
ancient environmental CH4 gas confined to a bubble in ice at the
polar regions, measurements of the absorption spectrum for a trace
gas of CH4 in a small area are attempted. For a 100-% CH4 gas
trapped in a ∼ 1 mm3 glass container, the absorption peaks of CH4
are obtained at 1.65 μm with a path length of 3 mm, and also the
gas pressure is extrapolated from the measured data.
Abstract: Recent advances in wireless networking technologies
introduce several energy aware routing protocols in sensor networks.
Such protocols aim to extend the lifetime of network by reducing the
energy consumption of nodes. Many researchers are looking for
certain challenges that are predominant in the grounds of energy
consumption. One such protocol that addresses this energy
consumption issue is ‘Cluster based hierarchical routing protocol’. In
this paper, we intend to discuss some of the major hierarchical
routing protocols adhering towards sensor networks. Furthermore, we
examine and compare several aspects and characteristics of few
widely explored hierarchical clustering protocols, and its operations
in wireless sensor networks (WSN). This paper also presents a
discussion on the future research topics and the challenges of
hierarchical clustering in WSNs.
Abstract: This research focuses on the optimization of glazed
surfaces and the assessment of possible solar gains in industrial
buildings. Existing window rating methods for single windows were
evaluated and a new method for a simple analysis of energy gains and
losses by single windows was introduced. Furthermore extensive
transient building simulations were carried out to appraise the
performance of low cost polycarbonate multi-cell sheets in
interaction with typical buildings for industrial applications. Mainly
energy saving potential was determined by optimizing the orientation
and area of such glazing systems in dependency on their thermal
qualities. Moreover the impact on critical aspects such as summer
overheating and daylight illumination was considered to ensure the
user comfort and avoid additional energy demand for lighting or
cooling. Hereby the simulated heating demand could be reduced by
up to 1/3 compared to traditional architecture of industrial halls using
mainly skylights.
Abstract: Novel bio-based polymer electrolyte was synthesized
with LiClO4 as the main source of charge carrier. Initially,
polyurethane-LiClO4 polymer electrolytes were synthesized via
prepolymerization method with different NCO/OH ratios and labelled
them as PU1, PU2, PU3 and PU4. Fourier transform infrared (FTIR)
analysis indicates the co-ordination between Li+ ion and polyurethane
in PU1. Differential scanning calorimetry (DSC) analysis indicates
PU1 has the highest glass transition temperature (Tg) corresponds to
the most abundant urethane group which is the hard segment in PU1.
Scanning electron microscopy (SEM) shows the good miscibility
between lithium salt and the polymer. The study found that PU1
possessed the greatest ionic conductivity and the lowest activation
energy, Ea. All the polyurethanes exhibited linear Arrhenius
variations indicating ion transport via simple lithium ion hopping in
polyurethane. This research proves the NCO content in polyurethane
plays an important role in affecting the ionic conductivity of this
polymer electrolyte.
Abstract: Theoretical optimization of a copper-water negative
inclination heat pipe with internal composite wick structure had been
performed, regarding a new introduced parameter: the ratio between
the coarse mesh wraps and the fine mesh wraps of the composite
wick. Since in many cases, the design of a heat pipe matches specific
thermal requirements and physical limitations, this work
demonstrates the optimization of a 1m length, 8mm internal diameter
heat pipe without an adiabatic section, at a negative inclination angle
of -10º. The optimization is based on a new introduced parameter, LR:
the ratio between the coarse mesh wraps and the fine mesh wraps.
Abstract: OEE has been used in many industries as measure of
performance. However due to limitations of original OEE, it has been
modified by various researchers. OEE for mining application is
special version of classic equation, carries these limitation over. In
this paper it has been aimed to modify the OEE for mining
application by introducing the weights to the elements of it and
termed as Mine Production index (MPi). As a special application of
new index MPishovel has been developed by authors. This can be used
for evaluating the shovel effectiveness. Based on analysis, utilization
followed by performance and availability were ranked in this order.
To check the applicability of this index, a case study was done on
four electrical and one hydraulic shovel in a Swedish mine. The
results shows that MPishovel can evaluate production effectiveness of
shovels and can determine effectiveness values in optimistic view
compared to OEE. MPi with calculation not only give the
effectiveness but also can predict which elements should be focused
for improving the productivity.
Abstract: Information and Communication Technologies (ICTs)
are pervasive nowadays, including in education where they are
expected to improve the performance of learners. However, the hope
placed in ICTs to find viable solutions to the problem of poor
academic performance in schools in the developing world has not yet
yielded the expected benefits. This problem serves as a motivation to
this study whose aim is to examine the perceptions of educators on
the advantages and disadvantages of e-learning. This aim will be
subdivided into two types of research objectives. Objectives on the
identification and design of theories and models will be achieved
using content analysis and literature review. However, the objective
on the empirical testing of such theories and models will be achieved
through the survey of educators from different schools in the
Pinetown District of the South African Kwazulu-Natal province.
SPSS is used to quantitatively analyse the data collected by the
questionnaire of this survey using descriptive statistics and Pearson
correlations after assessing the validity and the reliability of the data.
The main hypothesis driving this study is that there is a relationship
between the demographics of educators’ and their adherence to
learning theories on one side, and their perceptions on the advantages
and disadvantages of e-learning on the other side, as argued by
existing research; but this research views these learning theories
under three perspectives: educators’ adherence to self-regulated
learning, to constructivism, and to progressivism. This hypothesis
was fully confirmed by the empirical study except for the
demographic factor where teachers’ level of education was found to
be the only demographic factor affecting the perceptions of educators
on the advantages and disadvantages of e-learning.
Abstract: Ongoing landscape transformation is one of the major
causes behind disappearance of traditional landscapes, and lead to
species and resource loss. Tree in paddy fields in the northeast of
Thailand is one of those traditional landscapes. Using three different
historical time layers, we acknowledged the severe deforestation and
rapid urbanization happened in the region. Despite the general
thinking of decline in tree density as consequences, the heterogeneous
trend of changes in total tree density in three studied landscapes denied
the hypothesis that number of trees in paddy field depend on the length
of land use practice. On the other hand, due to selection of planting
new trees on levees, existence of trees in paddy field now relies on
their values for human use. Besides, changes in land use and landscape
structure had a significant impact on decision of which tree density
level is considered as suitable for the landscape.
Abstract: This paper presents a model predictive control (MPC)
of a utility interactive (UI) single phase inverter (SPI) for a
photovoltaic (PV) system at residential/distribution level. The
proposed model uses single-phase phase locked loop (PLL) to
synchronize SPI with the grid and performs MPC control in a dq
reference frame. SPI model consists of boost converter (BC),
maximum power point tracking (MPPT) control, and a full bridge
(FB) voltage source inverter (VSI). No PI regulators to tune and
carrier and modulating waves are required to produce switching
sequence. Instead, the operational model of VSI is used to synthesize
sinusoidal current and track the reference. Model is validated using a
three kW PV system at the input of UI-SPI in Matlab/Simulink.
Implementation and results demonstrate simplicity and accuracy, as
well as reliability of the model.
Abstract: One- and two-dimensional carbon nanostructures with
sp2 hybridization of carbon atoms (single walled carbon nanotubes
and graphene) are promising materials in future electronic and
spintronics devices due to specific character of their electronic
structure. In this paper we present a comparative study of graphene
and single-wall carbon nanotubes by Raman spectro-microscopy in
strong magnetic field. This unique method allows to study changes in
electronic band structure of the two types of carbon nanostructures
induced by a strong magnetic field.
Abstract: Advances technology in the field of photogrammetry
replaces analog cameras with reflection on aircraft GPS/IMU system
with a digital aerial camera. In this system, when determining the
position of the camera with the GPS, camera rotations are also
determined by the IMU systems. All around the world, digital aerial
cameras have been used for the photogrammetry applications in the
last ten years. In this way, in terms of the work done in
photogrammetry it is possible to use time effectively, costs to be
reduced to a minimum level, the opportunity to make fast and
accurate.
Geo-referencing techniques that are the cornerstone of the GPS /
INS systems, photogrammetric triangulation of images required for
balancing (interior and exterior orientation) brings flexibility to the
process. Also geo-referencing process; needed in the application of
photogrammetry targets to help to reduce the number of ground
control points. In this study, the use of direct and indirect georeferencing
techniques on the accuracy of the points was investigated
in the production of photogrammetric mapping.
Abstract: This article presents summary on preparation and
characterization of zinc, copper, cadmium and cobalt chromite
nanocrystals, embedded in an amorphous silica matrix. The
ZnCr2O4/SiO2, CuCr2O4/SiO2, CdCr2O4/SiO2 and CoCr2O4/SiO2
nanocomposites were prepared by a conventional sol-gel method
under acid catalysis. Final heat treatment of the samples was carried
out at temperatures in the range of 900−1200 ◦C to adjust the
phase composition and the crystallite size, respectively. The resulting
samples were characterized by Powder X-ray diffraction (PXRD),
High Resolution Transmission Electron Microscopy (HRTEM),
Raman/FTIR spectroscopy and magnetic measurements. Formation
of the spinel phase was confirmed in all samples. The average size of
the nanocrystals was determined from the PXRD data and by direct
particle size observation on HRTEM; both results were correlated.
The mean particle size (reviewed by HRTEM) was in the range from
∼4 to 46 nm. The results showed that the sol-gel method can be
effectively used for preparation of the spinel chromite nanoparticles
embedded in the silica matrix and the particle size is driven by the
type of the cation A2+ in the spinel structure and the temperature
of the final heat treatment. Magnetic properties of the nanocrystals
were found to be just moderately modified in comparison to the bulk
phases.
Abstract: This paper attempts to evaluate the effect of fire
damage on concrete by using nonlinear resonance vibration method,
one of the nonlinear nondestructive method. Concrete exhibits not
only nonlinear stress-strain relation but also hysteresis and discrete
memory effect which are contained in consolidated materials.
Hysteretic materials typically show the linear resonance frequency
shift. Also, the shift of resonance frequency is changed according to
the degree of micro damage. The degree of the shift can be obtained
through nonlinear resonance vibration method. Five exposure
scenarios were considered in order to make different internal micro
damage. Also, the effect of post-fire-curing on fire-damaged concrete
was taken into account to conform the change in internal damage.
Hysteretic nonlinearity parameter was obtained by amplitudedependent
resonance frequency shift after specific curing periods. In
addition, splitting tensile strength was measured on each sample to
characterize the variation of residual strength. Then, a correlation
between the hysteretic nonlinearity parameter and residual strength
was proposed from each test result.
Abstract: Diabetes is a growing health problem in worldwide.
Especially, the patients with Type 1 diabetes need strict glycemic
control because they have deficiency of insulin production. This
paper attempts to control blood glucose based on body mathematical
body model. The Bergman minimal mathematical model is used to
develop the nonlinear controller. A novel back-stepping based sliding
mode control (B-SMC) strategy is proposed as a solution that
guarantees practical tracking of a desired glucose concentration. In
order to show the performance of the proposed design, it is compared
with conventional linear and fuzzy controllers which have been done
in previous researches. The numerical simulation result shows the
advantages of sliding mode back stepping controller design to linear
and fuzzy controllers.
Abstract: Due to reduced stiffness, research on second
generation titanium alloys for implant applications, like the
metastable β-titanium alloy Ti-15Mo, become more and more
important in the recent years. The machinability of these alloys is
generally poor leading to problems during implant production and
comparably large production costs. Therefore, in the present study,
Ti-15Mo was alloyed with 0.8 wt.-% of the rare earth metals
lanthanum (Ti-15Mo+0.8La) and neodymium (Ti-15Mo+0.8Nd) to
improve its machinability. Their microstructure consisted of a
titanium matrix and micrometer-size particles of the rare earth metals
and two of their oxides. The particles stabilized the microstructure as
grain growth was minimized. As especially the ductility might be
affected by the precipitates, the behavior of Ti-15Mo+0.8La and Ti-
15Mo+0.8Nd was investigated during static and dynamic
deformation at elevated temperature to develop a processing route.
The resulting mechanical properties (static strength and ductility)
were similar in all investigated alloys.
Abstract: In the present work, the effect of load and sliding
distance on the performance tribology of commercially used
aluminium-silicon engine block and piston was evaluated at ambient
conditions with humidity of 80% under dry sliding conditions using a
pin-on-disc with two different loads of 5N and 20N yielding applied
pressure of 0.30MPa and 1.4MPa, respectively, at sliding velocity of
0.29ms-1 and with varying sliding distance ranging from 260m-
4200m. Factors and conditions that had significant effect were
identified. The results showed that the load and the sliding distance
affect the wear rate of the alloys and the wear rate increased with
increasing load for both the alloys. Wear rate also increases almost
linearly at low loads and increase to a maximum then attain a plateau
with increasing sliding distance. For both applied loads the piston
alloy showed the better performance due to higher Ni and Mg
content. The worn surface and wear debris was characterized by
optical microscope, SEM and EDX analyzer. The worn surface was
characterized by surface with shallow grooves at loads while the
groove width and depth increased as the loads increases. Oxidative
wear was found to be the predominant mechanisms in the dry sliding
of Al-Si alloys at low loads.
Abstract: The aim of the paper was to elaborate a novel calculator BasWilCalc, that allows to estimate the actual amount of biomass on the basket willow plantations. The proposed method is based on the results of field experiment conducted during years 2011-2013 on basket willow plantation in the south-western part of Poland. As input data the results of destructive measurements of the diameter, length and weight of willow stems and non-destructive biometric measurements of diameter in the middle of stems and their length during the growing season performed at weekly intervals were used. Performed analysis enabled to develop the algorithm which, due to the fact that energy plantations are of known and constant planting structure, allows to estimate the actual amount of willow basket biomass on the plantation with a given probability and accuracy specified by the model, based on the number of stems measured and the age of the plantation.
Abstract: The mathematical analysis on radiation obtained and
the development of the solar photovoltaic (PV) array groundwater
pumping is needed in the rural areas of Thohoyandou for sizing and
power performance subject to the climate conditions within the area.
A simple methodology approach is developed for the directed
coupled solar, controller and submersible ground water pump system.
The system consists of a PV array, pump controller and submerged
pump, battery backup and charger controller. For this reason, the
theoretical solar radiation is obtained for optimal predictions and
system performance in order to achieve different design and
operating parameters. Here the examination of the PV schematic
module in a Direct Current (DC) application is used for obtainable
maximum solar power energy for water pumping. In this paper, a
simple efficient photovoltaic water pumping system is presented with
its theoretical studies and mathematical modeling of photovoltaics
(PV) system.
Abstract: Calcium phosphate coating (CaP) has been employed
for protein delivery, but the typical direct protein adsorption on the
coating led to low incorporation content and fast release of the
protein from the coating. By using bovine serum albumin (BSA) as a
model protein, rapid biomimetic co-precipitation between calcium
phosphate and BSA was employed to control the distribution of BSA
within calcium phosphate coating during biomimetic formation on
titanium surface for only 6 h at 50oC in an accelerated calcium
phosphate solution. As a result, the amount of BSA incorporation and
release duration could be increased by using a rapid biomimetic coprecipitation
technique. Up to 43 fold increases in the BSA
incorporation content and the increase from 6 h to more than 360 h in
release duration compared to typical direct adsorption technique were
observed depending on the initial BSA concentration used during coprecipitation
(1, 10 and 100 μg.ml-1). From x-ray diffraction and
Fourier transform infrared spectroscopy studies, the coating
composition was not altered with the incorporation of BSA by this
rapid biomimetic co-precipitation and mainly comprised octacalcium
phosphate and hydroxyapatite. However, the microstructure of
calcium phosphate crystals changed from straight, plate-like units to
curved, plate-like units with increasing BSA content.
Abstract: The article presents the concept of an electromagnetic
circuit generator with permanent magnets mounted on the surface
rotor core designed for single phase work. Computation field-circuit
model was shown. The spectrum of time course of voltages in the
idle work was presented. The cross section with graphically
presentation of magnetic induction in particular parts of
electromagnetic circuits was presented. Distribution of magnetic
induction at the rated load point for each phase was shown. The time
course of voltages and currents for each phases for rated power were
displayed. An analysis of laboratory results and measurement of load
characteristics of the generator was discussed. The work deals with
three electromagnetic circuits of generators with permanent magnet
where output voltage characteristics versus rated power were
expressed.