Abstract: Indium-tin oxide films are deposited by low plasma
temperature RF sputtering on highly flexible modification of glycol
polyethyleneterephtalate substrates. The produced layers are
characterized with transparency over 82 % and sheet resistance of
86.9 Ω/square. The film’s conductivity was further improved by
additional UV illumination from light source (365 nm), having power
of 250 W. The influence of the UV exposure dose on the structural
and electro-optical properties of ITO was investigated. It was
established that the optimum time of illumination is 10 minutes and
further UV treatment leads to polymer substrates degradation.
Structural and bonds type analysis show that at longer treatment
carbon atoms release and diffuse into ITO films, which worsen their
electrical behavior. For the optimum UV dose the minimum sheet
resistance was measured to be 19.2 Ω/square, and the maximum
transparency remained almost unchanged – above 82 %.
Abstract: The pulp and paper mill effluent is one of the high
polluting effluent amongst the effluents obtained from polluting
industries. All the available methods for treatment of pulp and paper
mill effluent have certain drawbacks. The coagulation is one of the
cheapest process for treatment of various organic effluents. Thus, the
removal of chemical oxygen demand (COD) and colour of paper mill
effluent is studied using coagulation process. The batch coagulation
process was performed using various coagulants like: aluminium
chloride, poly aluminium chloride and copper sulphate. The initial
pH of the effluent (Coagulation pH) has tremendous effect on COD
and colour removal. Poly aluminium chloride (PAC) as coagulant
reduced COD to 84 % and 92 % of colour was removed at an
optimum pH 5 and coagulant dose of 8 ml l-1. With aluminium
chloride at an optimum pH = 4 and coagulant dose of 5 g l-1, 74 %
COD and 86 % colour removal were observed. The results using
copper sulphate as coagulant (a less commercial coagulant) were
encouraging. At an optimum pH 6 and mass loading of 5 g l-1, 76 %
COD reduction and 78 % colour reduction were obtained. It was also
observed that after addition of coagulant, the pH of the effluent
decreases. The decrease in pH was highest for AlCl3, which was
followed by PAC and CuSO4. Significant amount of COD reductions
was obtained by coagulation process. Since the coagulation process
is the first stage for treatment of effluent and some of the coagulant
cations usually remain in the treated effluents. Thus, cation like
copper may be one of the good catalyst for second stage of treatment
process like wet oxidation. The copper has been found to be good
oxidation catalyst then iron and aluminum.
Abstract: The research was set up on chernozem soil at the Látókép AGTC MÉK research area of the University of Debrecen in Hungary. We examined the yield, the yield production per 1kg NPK fertilizer and the water and nutrient utilization of hybrid PR37N01 and PR37M81 in 2013. We found that PR37N01 produced the most yield at the level of N120+P (17,476kg ha-1) while PR37M81 reached the highest yield at level N150+PK (16,754kg ha-1). Studies related to yield production per 1kg NPK indicated that the best results were achieved at level N30+PK compared to the control treatment. Yield production per 1kg NPK was17.6kg kg-1 by P37N01 and 44.2kg kg-1 by PR37M81. By comparing the water utilization of hybrids we found that the worst water utilization results were reached in the control treatment (PR37N01: 26.2kg mm-1, PR37M81: 19.5kg mm-1). The best water utilization values were produced at level N120+PK in the case of hybrid PR37N01 (32.1kg mm-1) and at N150+PK in the case of hybrid PR37M81 (30.8kg mm-1). We established the values of the nutrient reaction and the fertilizer optimum of hybrids. We discovered a strong relationship between the amount of fertilizer applied and the yield produced (r2= 0.8228–0.9515). The best nutrient response was induced by hybrid PR37N01, while the weakest results were reached by hybrid PR37M81.
Abstract: Simulation accuracy by recent dynamic vehicle
simulation multidimensional expression significantly has progressed
and acceptable results not only for passive vehicles but also for
active vehicles normally equipped with advanced electronic
components is also provided. Recently, one of the subjects that has it
been considered, is increasing the safety car in design. Therefore,
many efforts have been done to increase vehicle stability especially
in the turn. One of the most important efforts is adjusting the camber
angle in the car suspension system. Optimum control camber angle in
addition to the vehicle stability is effective in the wheel adhesion on
road, reducing rubber abrasion and acceleration and braking. Since
the increase or decrease in the camber angle impacts on the stability
of vehicles, in this paper, a car suspension system mechanism is
introduced that could be adjust camber angle and the mechanism is
application and also inexpensive. In order to reach this purpose, in
this paper, a passive double wishbone suspension system with
variable camber angle is introduced and then variable camber
mechanism designed and analyzed for study the designed system
performance, this mechanism is modeled in Visual Nastran software
and kinematic analysis is revealed.
Abstract: This paper introduces a mixed integer programming model to find the optimum development plan for port Anzali. The model minimizes total system costs taking into account both port infrastructure costs and shipping costs. Due to the multipurpose function of the port, the model consists of 1020 decision variables and 2490 constraints. Results of the model determine the optimum number of berths that should be constructed in each period and for each type of cargo. In addition to, the results of sensitivity analysis on port operation quantity provide useful information for managers to choose the best scenario for port planning with the lowest investment risks. Despite all limitations-due to data availability-the model offers a straightforward decision tools to port planners aspiring to achieve optimum port planning steps.
Abstract: An accurate optimal design of laminated composite
structures may present considerable difficulties due to the complexity
and multi-modality of the functional design space. The Big Bang
– Big Crunch (BB-BC) optimization method is a relatively new
technique and has already proved to be a valuable tool for structural
optimization. In the present study the exceptional efficiency of the
method is demonstrated by an example of the lay-up optimization
of multilayered anisotropic cylinders based on a three-dimensional
elasticity solution. It is shown that, due to its simplicity and speed,
the BB-BC is much more efficient for this class of problems when
compared to the genetic algorithms.
Abstract: This study deals with a multi-criteria optimization
problem which has been transformed into a single objective
optimization problem using Response Surface Methodology (RSM),
Artificial Neural Network (ANN) and Grey Relational Analyses
(GRA) approach. Grey-RSM and Grey-ANN are hybrid techniques
which can be used for solving multi-criteria optimization problem.
There have been two main purposes of this research as follows.
1. To determine optimum and robust fiber dyeing process
conditions by using RSM and ANN based on GRA,
2. To obtain the best suitable model by comparing models
developed by different methodologies.
The design variables for fiber dyeing process in textile are
temperature, time, softener, anti-static, material quantity, pH,
retarder, and dispergator. The quality characteristics to be evaluated
are nominal color consistency of fiber, maximum strength of fiber,
minimum color of dyeing solution. GRA-RSM with exact level
value, GRA-RSM with interval level value and GRA-ANN models
were compared based on GRA output value and MSE (Mean Square
Error) performance measurement of outputs with each other. As a
result, GRA-ANN with interval value model seems to be suitable
reducing the variation of dyeing process for GRA output value of the
model.
Abstract: Although lighting systems powered by Photovoltaic
(PV) cells have existed for many years, they are not widely used,
especially in lighting for buildings, due to their high initial cost and
low conversion efficiency. One of the technical challenges facing PV
powered lighting systems has been how to use dc power generated by
the PV module to energize common light sources that are designed to
operate efficiently under ac power. Usually, the efficiency of the dc
light sources is very poor compared to ac light sources. Rapid
developments in LED lighting systems have made this technology a
potential candidate for PV powered lighting systems. This study
analyzed the efficiency of each component of PV powered lighting
systems to identify optimum system configurations for different
applications.
Abstract: In this manuscript, we discuss the problem of determining the optimum stratification of a study (or main) variable based on the auxiliary variable that follows a uniform distribution. If the stratification of survey variable is made using the auxiliary variable it may lead to substantial gains in precision of the estimates. This problem is formulated as a Nonlinear Programming Problem (NLPP), which turn out to multistage decision problem and is solved using dynamic programming technique.
Abstract: In this paper we present a Feed-Foward Neural
Networks Autoregressive (FFNN-AR) model with genetic algorithms
training optimization in order to predict the gross domestic product
growth of six countries. Specifically we propose a kind of weighted
regression, which can be used for econometric purposes, where the
initial inputs are multiplied by the neural networks final optimum
weights from input-hidden layer of the training process. The
forecasts are compared with those of the ordinary autoregressive
model and we conclude that the proposed regression-s forecasting
results outperform significant those of autoregressive model.
Moreover this technique can be used in Autoregressive-Moving
Average models, with and without exogenous inputs, as also the
training process with genetics algorithms optimization can be
replaced by the error back-propagation algorithm.
Abstract: In this research, a systematic investigation was carried out to determine the optimum conditions of HDS reactor. Moreover, a suitable model was developed for a rigorous RTO (real time optimization) loop of HDS (Hydro desulfurization) process. A systematic experimental series was designed based on CCD (Central Composite design) and carried out in the related pilot plant to tune the develop model. The designed variables in the experiments were Temperature, LHSV and pressure. However, the hydrogen over fresh feed ratio was remained constant. The ranges of these variables were respectively equal to 320-380ºC, 1- 21/hr and 50-55 bar. a power law kinetic model was also developed for our further research in the future .The rate order and activation energy , power of reactant concentration and frequency factor of this model was respectively equal to 1.4, 92.66 kJ/mol and k0=2.7*109 .
Abstract: In this paper we are to find the optimum
multiwavelet for compression of electrocardiogram (ECG)
signals. At present, it is not well known which multiwavelet is
the best choice for optimum compression of ECG. In this
work, we examine different multiwavelets on 24 sets of ECG
data with entirely different characteristics, selected from MITBIH
database. For assessing the functionality of the different
multiwavelets in compressing ECG signals, in addition to
known factors such as Compression Ratio (CR), Percent Root
Difference (PRD), Distortion (D), Root Mean Square Error
(RMSE) in compression literature, we also employed the
Cross Correlation (CC) criterion for studying the
morphological relations between the reconstructed and the
original ECG signal and Signal to reconstruction Noise Ratio
(SNR). The simulation results show that the cardbal2 by the
means of identity (Id) prefiltering method to be the best
effective transformation.
Abstract: Antimicrobial (AM) starch-based films were
developed by incorporating chitosan and lauric acid as antimicrobial
agent into starch-based film. Chitosan has wide range of applications
as a biomaterial, but barriers still exist to its broader use due to its
physical and chemical limitations. In this work, a series of
starch/chitosan (SC) blend films containing 8% of lauric acid was
prepared by casting method. The structure of the film was
characterized by Fourier transform infrared spectroscopy (FTIR), Xray
diffraction (XRD), and scanning electron microscopy (SEM).
The results indicated that there were strong interactions were present
between the hydroxyl groups of starch and the amino groups of
chitosan resulting in a good miscibility between starch and chitosan
in the blend films. Physical properties and optical properties of the
AM starch-based film were evaluated. The AM starch-based films
incorporated with chitosan and lauric acid showed an improvement in
water vapour transmission rate (WVTR) and addition of starch
content provided more transparent films while the yellowness of the
film attributed to the higher chitosan content. The improvement in
water barrier properties was mainly attributed to the hydrophobicity
of lauric acid and optimum chitosan or starch content. AM starch
based film also showed excellent oxygen barrier. Obtaining films
with good oxygen permeability would be an indication of the
potential use of these antimicrobial packaging as a natural packaging
and an alternative packaging to the synthetic polymer to protect food
from oxidation reactions
Abstract: Over Current Relays (OCRs) and Directional Over Current Relays (DOCRs) are widely used for the radial protection and ring sub transmission protection systems and for distribution systems. All previous work formulates the DOCR coordination problem either as a Non-Linear Programming (NLP) for TDS and Ip or as a Linear Programming (LP) for TDS using recently a social behavior (Particle Swarm Optimization techniques) introduced to the work. In this paper, a Modified Particle Swarm Optimization (MPSO) technique is discussed for the optimal settings of DOCRs in power systems as a Non-Linear Programming problem for finding Ip values of the relays and for finding the TDS setting as a linear programming problem. The calculation of the Time Dial Setting (TDS) and the pickup current (Ip) setting of the relays is the core of the coordination study. PSO technique is considered as realistic and powerful solution schemes to obtain the global or quasi global optimum in optimization problem.
Abstract: Due to the limited energy resources, energy efficient operation of sensor node is a key issue in wireless sensor networks. Clustering is an effective method to prolong the lifetime of energy constrained wireless sensor network. However, clustering in wireless sensor network faces several challenges such as selection of an optimal group of sensor nodes as cluster, optimum selection of cluster head, energy balanced optimal strategy for rotating the role of cluster head in a cluster, maintaining intra and inter cluster connectivity and optimal data routing in the network. In this paper, we propose a protocol supporting an energy efficient clustering, cluster head selection/rotation and data routing method to prolong the lifetime of sensor network. Simulation results demonstrate that the proposed protocol prolongs network lifetime due to the use of efficient clustering, cluster head selection/rotation and data routing.
Abstract: Owning to the high-speed feed rate and ultra spindle
speed have been used in modern machine tools, the tool-path
generation plays a key role in the successful application of a
High-Speed Machining (HSM) system. Because of its importance in
both high-speed machining and tool-path generation, approximating a
contour by NURBS format is a potential function in CAD/CAM/CNC
systems. It is much more convenient to represent an ellipse by
parametric form than to connect points laboriously determined in a
CNC system. A new approximating method based on optimum
processes and NURBS curves of any degree to the ellipses is presented
in this study. Such operations can be the foundation of tool-radius
compensation interpolator of NURBS curves in CNC system. All
operating processes for a CAD tool is presented and demonstrated by
practical models.
Abstract: This work presents the hydrogen production from
steam gasification of palm kernel shell (PKS) at 700 oC in the
presence of 5% Ni/BEA and 5% Fe/BEA as catalysts. The steam
gasification was performed in two-staged reactors to evaluate the
effect of calcinations temperature and the steam to biomass ratio on
the product gas composition. The catalytic activity of Ni/BEA
catalyst decreases with increasing calcinations temperatures from 500
to 700 oC. The highest H2 concentration is produced by Fe/BEA
(600) with more than 71 vol%. The catalytic activity of the catalysts
tested is found to correspond to its physicochemical properties. The
optimum range for steam to biomass ratio if found to be between 2 to
4. Excess steam content results in temperature drop in the gasifier
which is undesirable for the gasification reactions.
Abstract: For a determined intermediate band position, the effects of electron filling factor and sunlight concentration on the active region thickness and efficiency of the quantum-dot intermediate band solar cell are calculated. For each value of electron filling factor, the maximum point of efficiency obtained and resulted in the optimum thickness of the cell under three different sunlight concentrations. We show the importance of filling factor as a parameter to be more considered. The photon recycling effect eliminated in all calculations.
Abstract: This paper presents performance analysis of the
Evolutionary Programming-Artificial Neural Network (EPANN)
based technique to optimize the architecture and training parameters
of a one-hidden layer feedforward ANN model for the prediction of
energy output from a grid connected photovoltaic system. The ANN
utilizes solar radiation and ambient temperature as its inputs while the
output is the total watt-hour energy produced from the grid-connected
PV system. EP is used to optimize the regression performance of the
ANN model by determining the optimum values for the number of
nodes in the hidden layer as well as the optimal momentum rate and
learning rate for the training. The EPANN model is tested using two
types of transfer function for the hidden layer, namely the tangent
sigmoid and logarithmic sigmoid. The best transfer function, neural
topology and learning parameters were selected based on the highest
regression performance obtained during the ANN training and testing
process. It is observed that the best transfer function configuration for
the prediction model is [logarithmic sigmoid, purely linear].
Abstract: The theatre-auditorium under investigation following
the highly reflective characteristics of materials used in it (marble,
painted wood, smooth plaster, etc), architectural and structural
features of the Protocol and its intended use (very multifunctional:
Auditorium, theatre, cinema, musicals, conference room) from the
analysis of the statement of fact made by the acoustic simulation
software Ramsete and supported by data obtained through a
campaign of acoustic measurements of the state of fact made on the
spot by a Fonomet Svantek model SVAN 957, appears to be
acoustically inadequate. After the completion of the 3D model
according to the specifications necessary software used forecast in
order to be recognized by him, have made three simulations, acoustic
simulation of the state of and acoustic simulation of two design
solutions.
Improved noise characteristics found in the first design solution,
compared to the state in fact consists therefore in lowering
Reverberation Time that you turn most desirable value, while the
Indicators of Clarity, the Baricentric Time, the Lateral Efficiency,
Ratio of Low Tmedia BR and defined the Speech Intelligibility
improved significantly. Improved noise characteristics found instead
in the second design solution, as compared to first design solution, is
finally mostly in a more uniform distribution of Leq and in lowering
Reverberation Time that you turn the optimum values. Indicators of
Clarity, and the Lateral Efficiency improve further but at the expense
of a value slightly worse than the BR. Slightly vary the remaining
indices.