Abstract: The development of an low cost acquisition system of S-EMG signals which are reliable, comfortable for the user and with high mobility shows to be a relevant proposition in modern biomedical engineering scenario. In the study, the sampling capacity of the Arduino microcontroller Atmel Atmega328 with an A / D converter with 10-bit resolution and its reconstructing capability of a signal of surface electromyography is analyzed. An electronic circuit to capture the signal through two differential channels was designed, signals from Biceps Brachialis of a healthy man of 21 years was acquired to test the system prototype. ARV, MDF, MNF and RMS estimators were used to compare de acquired signals with physiological values. The Arduino was configured with a sampling frequency of 1.5kHz for each channel, and the tests with the circuit designed offered a SNR of 20.57dB.
Abstract: The calcarenites carbonate rocks of the Quaternary ridges, which extend along the northwestern Mediterranean coastal plain of Egypt, represent an excellent model for the transformation of loose sediments to real sedimentary rocks by the different stages of meteoric diagenesis. The depositional and diagenetic fabrics of the rocks, in addition to the strata orientation, highly affect their ultimate compressive strength and other geotechnical properties.
There is a marked increase in the compressive strength (UCS) from the first to the fourth ridge rock samples. The lowest values are related to the loose packing, weakly cemented aragonitic ooid sediments with high porosity, besides the irregularly distributed of cement, which result in decreasing the ability of these rocks to withstand crushing under direct pressure. The high (UCS) values are attributed to the low porosity, the presence of micritic cement, the reduction in grain size and the occurrence of micritization and calcretization processes.
The strata orientation has a notable effect on the measured (UCS). The lowest values have been recorded for the samples cored in the inclined direction; whereas the highest values have been noticed in most samples cored in the vertical and parallel directions to bedding plane. In case of the inclined direction, the bedding planes were oriented close to the plane of maximum shear stress. The lowest and highest anisotropy values have been recorded for the first and the third ridges rock samples, respectively, which may attributed to the relatively homogeneity and well sorted grainstone of the first ridge rock samples, and relatively heterogeneity in grain and pore size distribution and degree of cementation of the third ridge rock samples, besides, the abundance of shell fragments with intraparticle pore spaces, which may produce lines of weakness within the rock.
Abstract: The knowledge about rock layers thickness,especially above drilled mining pavements is crucial for workers safety. The measuring systems used nowadays are generally imperfect and there is a strong demand for improvement. The application of a new type of a measurement system called Self-excited Acoustical System is presentedin the paper. The system was applied until now to monitor stress changes in metal and concrete constructions. The change in measurement methodology resulted in possibility of measuring the thickness of the rocks above the tunnels as well as thickness of a singular rocklayer. The idea is to find two resonance frequencies of the self-exited system,which consists of a vibration exciter and vibration receiver placed at a distance, which are coupled with a proper power amplifier, and which operate in a closed loop with a positive feedback. The resonance with the higher amplitude determines thickness of the whole rock, whereas the lower amplitude resonance indicates thickness of a singular layer. The results of the laboratory tests conducted on a group of different rock materials are also presented.
Abstract: Ground Coupled Heat Pumps (GCHPs) exploit effectively the heat capacity of the ground, with the use of Ground Heat Exchangers (GHE). Depending on the mode of operation of the GCHPs, GHEs dissipate or absorb heat from the ground. For sizing the GHE the thermal properties of the ground need to be known. This paper gives information about the density, thermal conductivity, specific heat and thermal diffusivity of various lithologies encountered in Cyprus with various relations between these properties being examined through comparison and modeling. The results show that the most important correlation is the one encountered between thermal conductivity and thermal diffusivity with both properties showing similar response to the inlet and outlet flow temperature of vertical and horizontal heat exchangers.
Abstract: Vacant City of Cape Town-owned land lying unutilized and -productive could be developed for land uses such as urban agriculture that may improve the livelihoods of low income families. The new City of Cape Town zoning scheme includes an Urban Agriculture zoning for the first time. Unstructured qualitative interviews among town planners revealed their optimism about this inclusion as it will provide low-income residents with opportunities to generate an income. An existing farming community at Philippi, located within the municipal boundary of the city, was approached and empirical data obtained through questionnaires provided proof that urban agriculture could be viable in a coastal metropolitan city such as Cape Town even if farmers only produce for their own households. The lease method proposed for urban agriculture is a usufruct agreement conferring the right to another party, other than the legal owner, to enjoy the use and advantages of the property.
Abstract: As internet continues to expand its usage with an
enormous number of applications, cyber-threats have significantly
increased accordingly. Thus, accurate detection of malicious traffic in
a timely manner is a critical concern in today’s Internet for security.
One approach for intrusion detection is to use Machine Learning (ML)
techniques. Several methods based on ML algorithms have been
introduced over the past years, but they are largely limited in terms of
detection accuracy and/or time and space complexity to run. In this
work, we present a novel method for intrusion detection that
incorporates a set of supervised learning algorithms. The proposed
technique provides high accuracy and outperforms existing techniques
that simply utilizes a single learning method. In addition, our
technique relies on partial flow information (rather than full
information) for detection, and thus, it is light-weight and desirable for
online operations with the property of early identification. With the
mid-Atlantic CCDC intrusion dataset publicly available, we show that
our proposed technique yields a high degree of detection rate over 99%
with a very low false alarm rate (0.4%).
Abstract: Numerical study of heat transfer and fluid flow over vertical double forward facing step were presented. The k-w model with finite volume method was employed to solve continuity, momentum, and energy equations. Different step heights were adopted for range of Reynolds number varied from 10000 to 40000, and range of temperature varied from 310K to 340 K. The straight side of duct is insulated while the side of double forward facing step is heated. The result shows augmentation of heat transfer due to the recirculation region created after and before steps. Effect of step length and Reynolds number observed on increase of local Nusselt number particularly at recirculation regions. Contour of streamline velocity is plotted to show recirculation regions after and before steps. Numerical simulation in this paper done by used ANSYS FLUENT 14.
Abstract: Heat transfer and laminar fluid flow over backward facing step with and without obstacle numerically studied in this paper. The finite volume method adopted to solve continuity, momentum and energy equations in two dimensions. Backward facing step without obstacle and with different dimension of obstacle were presented. The step height and expansion ratio of channel were 4.8mm and 2 respectively, the range of Reynolds number varied from 75 to 225, constant heat flux subjected on downstream of wall was 2000W/m2, and length of obstacle was 1.5, 3, and 4.5mm with width 1.5mm. The separation length noticed increase with increase Reynolds number and height of obstacle. The result shows increase of heat transfer coefficient for backward facing step with obstacle in compared to those without obstacle. The maximum enhancement of heat transfer observed at 4.5mm of height obstacle due to increase recirculation flow after the obstacle in addition that at backward. Streamline of velocity showing the increase of recirculation region with used obstacle in compared without obstacle and highest recirculation region observed at obstacle height 4.5mm. The amount of enhancement heat transfer was varied between 3-5% compared to backward without obstacle.
Abstract: The results of the study on the project evaluation to
develop the competencies, capabilities, and skills in repairing
computers of people in Jompluak Local Municipality, Bang Khonthi
District, Samut Songkram Province showed that the overall result
was good (4.33). When considering on each aspect, it was found that
the highest one was on process evaluation (4.60) followed by product
evaluation (4.50) and the least one was on feeding factor (3.97).
When considering in details, it was found that: 1) the context aspect
was high (4.23) with the highest item on the arrangement of the
training situation (4.67) followed by the appropriateness of the target
(4.30) and the least aspect was on the project cooperation (3.73). 2)
The evaluation of average overall primary factor or feeding factor
showed high value (4.23) while the highest aspect was on the
capability of the trainers (4.47) followed by the suitable venue (4.33)
while the least aspect was on the insufficient budget (3.47). 3) The
average result of process evaluation was very high (4.60). The
highest aspect was on the follow-op supervision (4.70) followed by
responsibility of each project staffs (4.50) while the least aspect was
on the present situation and the problems of the community (4.40). 4)
The overall result of the product evaluation was very high (4.50). The
highest aspect was on the diversity of the activities and the
community integration (4.67) followed by project target achievement
(4.63) while the least aspect was on continuation and regularity of the
activities (4.33). The trainees reported high satisfaction on the project
management at very high level (43.33%) while 40% reported high
level and 16.67% reported moderate level. Suggestions for the project
were on the additional number of the computer sets (37.78%)
followed by longer training period especially on computer skills
(43.48%).
Abstract: A thin gold metal layer was deposited on the top of
silicon oxide films containing embedded Si nanocrystals (Si-nc). The
sample was annealed in a gas containing nitrogen, and subsequently
characterized by photoluminescence. We obtained 3-fold
enhancement of photon emission from the Si-nc embedded in silicon
dioxide covered with a Gold layer as compared with an uncovered
sample. We attribute this enhancement to the increase of the
spontaneous emission rate caused by the coupling of the Si-nc
emitters with the surface plasmons (SP). The evolution of PL
emission with laser irradiated time was also collected from covered
samples, and compared to that from uncovered samples. In an
uncovered sample, the PL intensity decreases with time,
approximately with two decay constants. Although the decrease of
the initial PL intensity associated with the increase of sample
temperature under CW pumping is still observed in samples covered
with a gold layer, this film significantly contributes to reduce the
permanent deterioration of the PL intensity. The resistance to
degradation of light-emitting silicon nanocrystals can be increased by
SP coupling to suppress the permanent deterioration. Controlling the
permanent photodeterioration can allow to perform a reliable optical
gain measurement.
Abstract: The objectives of this research were to study the management of local towns and to develop a better model of town management according to the Philosophy of Sufficiency Economy. This study utilized qualitative research, field research, as well as documentary research at the same time. A total of 10 local towns or Tambons of Supanburi province, Thailand were selected for an in-depth interview. The findings revealed that the model of local town management according to Philosophy of Sufficient Economy was in a level of “good” and the model of management has the five basic guidelines: 1) ability to manage budget information and keep it up-to-date, 2) ability to decision making according to democracy rules, 3) ability to use check and balance system, 4) ability to control, follow, and evaluation, and 5) ability to allow the general public to participate. In addition, the findings also revealed that the human resource management according to Philosophy of Sufficient Economy includes obeying laws, using proper knowledge, and having integrity in five areas: plan, recruit, select, train, and maintain human resources.
Abstract: Recently, ‘play of learning’ becomes important and is
emphasized as a useful learning tool. Therefore, interest in
edutainment contents is growing. Storytelling is considered first as a
method that improves the transmission of information and learner's
interest when planning edutainment contents. In this study, we
designed edutainment contents in the form of an adventure game that
applies the storytelling method. This content provides questions and
items constituted dynamically and reorganized learning contents
through analysis of test results. It allows learners to solve various
questions through effective iterative learning. As a result, the learners
can reach mastery learning.
Abstract: The paper presents an analysis of the innovation performance of small and medium-sized furniture enterprises in Bulgaria, accounting for over 97% of the companies in the sector. It contains advanced features of innovation in enterprises, specific features of the furniture industry in Bulgaria and analysis of the results of studies on the topic. The results from studies of three successive periods - 2006-2008; 2008-2010; 2010-2012, during which were studied 594 small and medium-sized furniture enterprises. There are commonly used in the EU definitions and indicators (European Commission, OECD, Oslo Manual), which allows for the comparability of results.
Abstract: Patients under health treatments that involve long
stays at a hospital or health center (e.g. cancer, organ transplants and
severe burns), tend to get bored or depressed because of the lack of
social interaction with family and friends. Such a situation also
affects the evolution and effectiveness of their treatments. In many
cases, the solution to this problem involves extra challenges, since
many patients need to rest quietly (or remain in bed) to their being
contagious. Considering the weak health condition in which usually
are these kinds, keeping them motivated and quiet represents an
important challenge for nurses and caregivers. This article presents a
mobile ubiquitous game called MagicRace, which allows hospitalized
kinds to interact socially with one another without putting to risk
their sensitive health conditions. The game does not require a
communication infrastructure at the hospital, but instead, it uses a
mobile ad hoc network composed of the handheld devices used by
the kids to play. The usability and performance of this application
was tested in two different sessions. The preliminary results show
that users experienced positive feelings from this experience.
Abstract: This paper proposes a novel e-learning model that is
based on a dynamic formative evaluation. On evaluating the existing
format of e-learning, conditions regarding repetitive learning to
achieve mastery, causes issues for learners to lose tension and become
neglectful of learning. The dynamic formative evaluation proposed is
able to supplement limitation of the existing approaches. Since a
repetitive learning method does not provide a perfect feedback, this
paper puts an emphasis on the dynamic formative evaluation that is
able to maximize learning achievement. Through the dynamic
formative evaluation, the instructor is able to refer to the evaluation
result when making an estimation about the learner. To show the flow
chart of learning, based on the dynamic formative evaluation, the
model proves its effectiveness and validity.
Abstract: The main aim of the current work is to examine if 14N
is candidate to be clusterized nuclei or not. In order to check this
attendance, we have measured the angular distributions for 14N ion
beam elastically scattered on 12C target nuclei at different low
energies; 17.5, 21, and 24.5MeV which are close to the Coulomb
barrier energy for 14N+12C nuclear system. Study of various transfer
reactions could provide us with useful information about the
attendance of nuclei to be in a composite form (core + valence). The
experimental data were analyzed using two approaches;
Phenomenological (Optical Potential) and semi-microscopic (Double
Folding Potential). The agreement between the experimental data and
the theoretical predictions is fairly good in the whole angular range.
Abstract: Waste of certain process can be the input source of
other sectors in order to reduce environmental pollution. Today there
are more and more solid wastes are generated, but only very small
amount of those are recycled. So, the threatening of environmental
pressure to public health is very serious. The methods considered for
the treatment of solid waste are biogas tanks or processing to make
animal feed and fertilizer, however, they did not perform well. An
alternative approach is growing mushrooms on waste residues. This
is regarded as an environmental friendly solution with potential
economical benefit. The substrate producers do their best to produce
quality substrate at low cost. Apart from other methods, this can be
achieved by employing biologically degradable wastes used as the
resource material component of the substrate. Mushroom growing is
a significant tool for the restoration, replenishment and remediation
of Earth’s overburdened ecosphere. One of the rational methods of
waste utilization involves locally available wastes. The present study
aims to find out the yield of mushroom grown on locally available
waste for free and to conserve our environment by recycling wastes.
Abstract: The Proton Exchange Membranes (PEM) are largely studied because they operate at low temperatures and they are suitable for mobile applications. However, there are some deficiencies in their operation, mainly those that use ethanol as a hydrogen source, that require a certain attention. Therefore, this research aimed to develop Nafion® composite membranes, mixing clay minerals, kaolin and halloysite to the polymer matrix in order to improve the ethanol molecule retentions and, at the same time, to keep the system’s protonic conductivity. The modified Nafion/Kaolin, Nafion/Halloysite composite membranes were prepared in weight proportion of 0.5, 1.0 and 1.5. The membranes obtained were characterized as to their ethanol permeability, protonic conductivity and water absorption. The composite morphology and structure are characterized by SEM and EDX and the thermal behavior is determined by TGA and DSC. The analysis of the results shows ethanol permeability reduction from 48% to 63%. However, the protonic conductivity results are lower in relation to pure Nafion®. As to the thermal behavior, the Nafion® composite membranes were stable up to a temperature of 325ºC.
Abstract: The application of data mining to environmental monitoring has become crucial for a number of tasks related to emergency management. Over recent years, many tools have been developed for decision support system (DSS) for emergency management. In this article a graphical user interface (GUI) for environmental monitoring system is presented. This interface allows accomplishing (i) data collection and observation and (ii) extraction for data mining. This tool may be the basis for future development along the line of the open source software paradigm.
Abstract: Measuring the reusability of Object-Oriented (OO) program code is important to ensure a successful and timely adaptation and integration of the reused code in new software projects. It has become even more relevant with the availability of huge amounts of open-source projects. Reuse saves cost, increases the speed of development and improves software reliability. Measuring this reusability is not s straight forward process due to the variety of metrics and qualities linked to software reuse and the lack of comprehensive empirical studies to support the proposed metrics or models. In this paper, a conceptual model is proposed to measure the reusability of OO program code. A comprehensive set of metrics is used to compute the most significant factors of reusability and an empirical investigation is conducted to measure the reusability of the classes of randomly selected open-source Java projects. Additionally, the impact of using inner and anonymous classes on the reusability of their enclosing classes is assessed. The results obtained are thoroughly analyzed to identify the factors behind lack of reusability in open-source OO program code and the impact of nesting on it.