Abstract: It is known that residual welding deformations give
negative effect to processability and operational quality of welded
structures, complicating their assembly and reducing strength.
Therefore, selection of optimal technology, ensuring minimum
welding deformations, is one of the main goals in developing a
technology for manufacturing of welded structures.
Through years, JSC SSTC has been developing a theory for
estimation of welding deformations and practical activities for
reducing and compensating such deformations during welding
process. During long time a methodology was used, based on analytic
dependence. This methodology allowed defining volumetric changes
of metal due to welding heating and subsequent cooling. However,
dependences for definition of structures deformations, arising as a
result of volumetric changes of metal in the weld area, allowed
performing calculations only for simple structures, such as units, flat
sections and sections with small curvature. In case of complex 3D
structures, estimations on the base of analytic dependences gave
significant errors.
To eliminate this shortage, it was suggested to use finite elements
method for resolving of deformation problem. Here, one shall first
calculate volumes of longitudinal and transversal shortenings of
welding joints using method of analytic dependences and further,
with obtained shortenings, calculate forces, which action is
equivalent to the action of active welding stresses. Further, a finiteelements
model of the structure is developed and equivalent forces
are added to this model. Having results of calculations, an optimal
sequence of assembly and welding is selected and special measures to
reduce and compensate welding deformations are developed and
taken.
Abstract: This paper proposes a cooperative Alamouti space time
transmission scheme with low relay complexity for the cooperative
communication systems. In the proposed scheme, the source node
combines the data symbols to construct the Alamouti-coded form at
the destination node, while the conventional scheme performs the
corresponding operations at the relay nodes. In simulation results,
it is shown that the proposed scheme achieves the second order
cooperative diversity while maintaining the same bit error rate (BER)
performance as that of the conventional scheme.
Abstract: In this paper, GSM signal strength was measured in
order to detect the type of the signal fading phenomenon using onedimensional
multilevel wavelet residual method and neural network
clustering to determine the average GSM signal strength received in
the study area. The wavelet residual method predicted that the GSM
signal experienced slow fading and attenuated with MSE of 3.875dB.
The neural network clustering revealed that mostly -75dB, -85dB and
-95dB were received. This means that the signal strength received in
the study is a weak signal.
Abstract: The fight against climate change and the replacement
of fossil energies nearing exhaustion gradually emerge as major
societal and economic challenges. It is possible to develop common
dates of low commercial value, and put on the local and international
market a new generation of products with high added values such as
bio ethanol. Besides its use in chemical synthesis, bio ethanol can be
blended with gasoline to produce a clean fuel while improving the
octane.
Abstract: The following case study presents the management of
stage III Differentiated Thyroid Cancer (DTC) patient in an NHS
hospital in London, UK during period of 2004-2005.
Abstract: Disasters are quite experienced in our days. They are
caused by floods, landslides, and building fires that is the main
objective of this study. To cope with these unexpected events,
precautions must be taken to protect human lives. The emphasis on
disposal work focuses on the resolution of the evacuation problem in
case of no-notice disaster. The problem of evacuation is listed as a
dynamic network flow problem. Particularly, we model the
evacuation problem as an earliest arrival flow problem with load
dependent transit time. This problem is classified as NP-Hard. Our
challenge here is to propose a metaheuristic solution for solving the
evacuation problem. We define our objective as the maximization of
evacuees during earliest periods of a time horizon T. The objective
provides the evacuation of persons as soon as possible. We
performed an experimental study on emergency evacuation from the
tunisian children’s hospital. This work prompts us to look for
evacuation plans corresponding to several situations where the
network dynamically changes.
Abstract: This paper presents the application of finite dynamic
programming, specifically the "Markov Chain" model, as part of the
decision making process of a company in the cosmetics sector located
in the vicinity of Bogota DC. The objective of this process was to
decide whether the company should completely reconstruct its
wastewater treatment plant or instead optimize the plant through the
addition of equipment. The goal of both of these options was to make
the required improvements in order to comply with parameters
established by national legislation regarding the treatment of waste
before it is released into the environment. This technique will allow
the company to select the best option and implement a solution for
the processing of waste to minimize environmental damage and the
acquisition and implementation costs.
Abstract: Because of high thermal efficiency and low CO2
emission, diesel engines are being used widely in many industrial
fields although it makes many PM and NOx which give both human
health and environment a negative effect. NOx regulations for diesel
engines, however, are being strengthened and it is impossible to meet
the emission standard without NOx reduction devices such as SCR
(Selective Catalytic Reduction), LNC (Lean NOx Catalyst), and LNT
(Lean NOx Trap). Among the NOx reduction devices, urea-SCR
system is known as the most stable and efficient method to solve the
problem of NOx emission. But this device has some issues associated
with the ammonia slip phenomenon which is occurred by shortage of
evaporation and thermolysis time, and that makes it difficult to achieve
uniform distribution of the injected urea in front of monolith.
Therefore, this study has focused on the mixing enhancement between
urea and exhaust gases to enhance the efficiency of the SCR catalyst
equipped in catalytic muffler by changing inlet gas temperature and
spray conditions to improve the spray uniformity of the urea water
solution. Finally, it can be found that various parameters such as inlet
gas temperature and injector and injection angles significantly affect
the evaporation and mixing of the urea water solution with exhaust
gases, and therefore, optimization of these parameters are required.
Abstract: A methodology is proposed for estimating the optical
attenuation and proportional depth variation of shallow inland water.
The process is demonstrated with EO-1 Hyperion hyperspectral and
IRS-P6 LISS-3 multispectral images of Kolkata city nearby area
centered around 22º33′ N 88º26′ E. The attenuation coefficient of
water was found to change with fine resolution of wavebands and in
presence of suspended organic matter in water.
Abstract: We present our approach on using continuous delivery
pattern for release management. One of the key practices of agile and
lean teams is the continuous delivery of new features to stakeholders.
The main benefits of this approach lie in the ability to release new
applications rapidly which has real strategic impact on the
competitive advantage of an organization. Organizations that
successfully implement Continuous Delivery have the ability to
evolve rapidly to support innovation, provide stable and reliable
software in more efficient ways, decrease the amount of resources
need for maintenance, and lower the software delivery time and costs.
One of the objectives of this paper is to elaborate a case study where
IT division of Central Securities Depository Institution (MKK) of
Turkey apply Continuous Delivery pattern to improve release
management process.
Abstract: Artificial Neural Networks (ANN) trained using backpropagation
(BP) algorithm are commonly used for modeling
material behavior associated with non-linear, complex or unknown
interactions among the material constituents. Despite multidisciplinary
applications of back-propagation neural networks
(BPNN), the BP algorithm possesses the inherent drawback of
getting trapped in local minima and slowly converging to a global
optimum. The paper present a hybrid artificial neural networks and
genetic algorithm approach for modeling slump of ready mix
concrete based on its design mix constituents. Genetic algorithms
(GA) global search is employed for evolving the initial weights and
biases for training of neural networks, which are further fine tuned
using the BP algorithm. The study showed that, hybrid ANN-GA
model provided consistent predictions in comparison to commonly
used BPNN model. In comparison to BPNN model, the hybrid ANNGA
model was able to reach the desired performance goal quickly.
Apart from the modeling slump of ready mix concrete, the synaptic
weights of neural networks were harnessed for analyzing the relative
importance of concrete design mix constituents on the slump value.
The sand and water constituents of the concrete design mix were
found to exhibit maximum importance on the concrete slump value.
Abstract: The study examines the influence of marital status on
consumers of products and services using blogs as a source of
information. A pre-designed questionnaire was used to collect the
primary data from the respondents (experiences). Data were collected
from one hundred and eighty seven respondents residing in and
around the Emirates of Sharjah and Dubai of the United Arab
Emirates. The collected data was analyzed with the help of statistical
tools such as averages, percentages, factor analysis, Student’s t-test
and Structural Equation Modelling Technique.
Objectives of the study are to know the reasons how married and
unmarried or single consumers of products and services are
motivated to use blogs as a source of information, to know whether
the consumers of products and services irrespective of their marital
status share their views and experiences with other bloggers and to
know the respondents’ future intentions towards blogging.
The study revealed the following: Majority of the respondents
have the motivation to blog because they are willing to receive
comments on what they post about services, convenience of blogs to
search for information about services and products, by blogging
respondents share information on the symptoms of a disease/ disorder
that may be experienced by someone, helps to share information
about ready to cook mix products and are keen to spend more time
blogging in the future.
Abstract: A simple multi-wavelength passively Q-switched
Erbium-doped fiber laser (EDFL) is demonstrated using low cost
multi-walled carbon nanotubes (MWCNTs) based saturable absorber
(SA), which is prepared using polyvinyl alcohol (PVA) as a host
polymer. The multi-wavelength operation is achieved based on
nonlinear polarization rotation (NPR) effect by incorporating 50 m
long photonic crystal fiber (PCF) in the ring cavity. The EDFL
produces a stable multi-wavelength comb spectrum for more than 14
lines with a fixed spacing of 0.48 nm. The laser also demonstrates a
stable pulse train with the repetition rate increases from 14.9 kHz to
25.4 kHz as the pump power increases from the threshold power of
69.0 mW to the maximum pump power of 133.8 mW. The minimum
pulse width of 4.4 μs was obtained at the maximum pump power of
133.8 mW while the highest energy of 0.74 nJ was obtained at pump
power of 69.0 mW.
Abstract: The biomass-based fuels have become great concern in order to replace the petroleum-based fuels. Biofuels are a wide range of fuels referred to liquid, gas and solid fuels produced from biomass. Recently, higher chain alcohols such as 3-methyl-1-butanol and isobutanol have become a better candidate compared to bioethanol in order to replace gasoline as transportation fuel. Therefore, in this study, 3-methyl-1-butanol was produced through a fermentation process by yeast. Several types of yeast involved in this research including Saccharomyces cerevisiae, Kluyveromyces lactis GG799 and Pichia pastoris (KM71H, GS115 and X33). The result obtained showed that K. lactis GG799 gave the highest concentration of 3-methyl-1-butanol at 274 mg/l followed by S. cerevisiae, P. pastoris GS115, P. pastoris KM71H and P. pastoris X33 at 265 mg/l, 190 mg/l, 182 mg/l and 174 mg/l respectively. Based on the result, it proved that yeast have a potential in producing 3-methyl-1-butanol naturally.
Abstract: In the present work, detailed analysis on flow characteristics of a pair of immiscible liquids through horizontal pipeline is simulated by using ANSYS FLUENT 6.2. Moderately viscous oil and water (viscosity ratio = 107, density ratio = 0.89 and interfacial tension = 0.024 N/m) have been taken as system fluids for the study. Volume of Fluid (VOF) method has been employed by assuming unsteady flow, immiscible liquid pair, constant liquid properties, and co-axial flow. Meshing has been done using GAMBIT. Quadrilateral mesh type has been chosen to account for the surface tension effect more accurately. From the grid independent study, we have selected 47037 number of mesh elements for the entire geometry. Simulation successfully predicts slug, stratified wavy, stratified mixed and annular flow, except dispersion of oil in water, and dispersion of water in oil. Simulation results are validated with horizontal literature data and good conformity is observed. Subsequently, we have simulated the hydrodynamics (viz., velocity profile, area average pressure across a cross section and volume fraction profile along the radius) of stratified wavy and annular flow at different phase velocities. The simulation results show that in the annular flow, total pressure of the mixture decreases with increase in oil velocity due to the fact that pipe cross section is completely wetted with water. Simulated oil volume fraction shows maximum at the centre in core annular flow, whereas, in stratified flow, maximum value appears at upper side of the pipeline. These results are in accord with the actual flow configuration. Our findings could be useful in designing pipeline for transportation of crude oil.
Abstract: Attractive and creative advertisement displays are
often in high demand as they are known to have profound impact on
the commercial market. In the fast advancement of technology,
advertising trend has taken a great leap in attracting more and more
demanding consumers. A low-cost and low-power consumption
flipping advertisement board has been developed in this paper. The
design of the electrical circuit and the controller of the advertisement
board are presented. A microcontroller, a Darlington Pair driver and a
unipolar stepper motor were used to operate the electrical flipping
advertisement board. The proposed system has been implemented
and the hardware has been tested to demonstrate the capability of
displaying multiple advertisements in a panel.
Abstract: Fluid rheology may have essential impact on sound propagation in a liquid-filled pipe, especially, in a low frequency range. Rheological parameters of liquid are temperature-sensitive, which ultimately results in a temperature dependence of the wave speed and attenuation in the waveguide. The study is devoted to modeling of this effect at sound propagation in an elastic pipe with polymeric liquid, described by generalized Maxwell model with non-zero high-frequency viscosity. It is assumed that relaxation spectrum is distributed according to the Spriggs law; temperature impact on the liquid rheology is described on the basis of the temperature-superposition principle and activation theory. The dispersion equation for the waveguide, considered as a thin-walled tube with polymeric solution, is obtained within a quasi-one-dimensional formulation. Results of the study illustrate the influence of temperature on sound propagation in the system.
Abstract: This paper presents the electrical effect of two neighboring distribution substation during the construction phase. The size of auxiliary grounding grid have an effect on entire grounding system. The bigger the size of auxiliary grounding grid, the lower the GPR and maximum touch voltage, with the exception that when the two grids are unconnected, i.e. the bigger the size of auxiliary grounding grid, the higher the maximum step voltage. The results in this paper could be served as design guideline of grounding system, and perhaps remedy of some troublesome grounding grids in power distribution’s system. Modeling and simulation is carried out on the Current Distribution Electromagnetic interference Grounding and Soil structure (CDEGS) program. The simulation results exhibit the design and analysis of power system grounding and perhaps could be set as a standard in grounding system design and modification in distribution substations.
Abstract: This work studied the ability of adipose tissue-derived
mesenchymal stromal cells (MSCs) to form stroma for expansion of
cord blood hematopoietic cells. We showed that 72-hour interaction
of MSCs with cord blood mononuclear cells (MNCs) in vitro at
atmospheric (20%) and low (5%) O2 conditions increased the
expression of ICAM-1, HCAM (at the beginning of interaction) on
MSCs. Viability of MSCs and MNCs were maintained at high level.
Adhesion of MNCs to MSCs was faster at 20% O2. MSCs promoted
the proliferation of adhered MNCs to form the suspension containing
great number of hematopoietic colony-forming units, and this effect
was more pronounced at 5% O2. Thus, adipose-derived MSCs
supplied sufficient stromal support to cord blood MNCs both at 20%
and 5% О2, providing their adhesion with further expansion of new
generation of different hematopoietic lineages.
Abstract: A theoretical study has been presented to describe the boundary layer flow and heat transfer on an exponentially shrinking sheet with a variable wall temperature and suction, in the presence of magnetic field. The governing nonlinear partial differential equations are converted into ordinary differential equations by similarity transformation, which are then solved numerically using the shooting method. Results for the skin friction coefficient, local Nusselt number, velocity profiles as well as temperature profiles are presented through graphs and tables for several sets of values of the parameters. The effects of the governing parameters on the flow and heat transfer characteristics are thoroughly examined.