Abstract: A fast settling multipath CMOS OTA for high speed
switched capacitor applications is presented here. With the basic
topology similar to folded-cascode, bandwidth and DC gain of the
OTA are enhanced by adding extra paths for signal from input to
output. Designed circuit is simulated with HSPICE using level 49
parameters (BSIM 3v3) in 0.35mm standard CMOS technology. DC
gain achieved is 56.7dB and Unity Gain Bandwidth (UGB) obtained
is 1.15GHz. These results confirm that adding extra paths for signal
can improve DC gain and UGB of folded-cascode significantly.
Abstract: Securing instream flows for aquatic ecosystems is
critical for sustainable water management and the promotion of
human and environmental health. Using a case study from the semiarid
region of southern Alberta (Canada) this paper considers how
the determination of instream flow standards requires judgments with
respect to: (1) The relationship between instream flow indicators and
assessments of overall environmental health; (2) The indicators used
to determine adequate instream flows, and; (3) The assumptions
underlying efforts to model instream flows given data constraints. It
argues that judgments in each of these areas have an inherently
ethical component because instream flows have direct effects on the
water(s) available to meet obligations to humans and non-humans.
The conclusion expands from the case study to generic issues
regarding instream flows, the growing water ethics literature and
prospects for linking science to policy.
Abstract: Deep Brain Stimulation or DBS is the second solution
for Parkinson's Disease. Its three parameters are: frequency, pulse
width and voltage. They must be optimized to achieve successful
treatment. Nowadays it is done clinically by neurologists and there is
not certain numerical method to detect them. The aim of this research
is to introduce simulation and modeling of Parkinson's Disease
treatment as a computational procedure to select optimum voltage.
We recorded finger tremor signals of some Parkinsonian patients
under DBS treatment at constant frequency and pulse width but
variable voltages; then, we adapted a new model to fit these data. The
optimum voltages obtained by data fitting results were the same as
neurologists- commented voltages, which means modeling can be
used as an engineering method to select optimum stimulation
voltages.
Abstract: Theexperiment was carried out with 2x5 male Merino
lambs raised under intensive conditions to investigate the effect of
dietary calcium soap of linseed oil on the color and fatty acid
composition of longissimusdorsi muscle. Control lambs fed a basal
diet and the experimental lambs consumed a diet supplemented with
3% calcium soap of linseed oil. The color values (L*, a*, b* a*/b*
and chroma) were not influenced by dietary treatment. The MUFA
proportion reduced, SFA and PUFA content did not alter. As
expected, the linolenic (C18:3 n3) and thusthe n-3 content
significantly improved by linseed supplement (0.47 and 0.81; 0.78
and 1.16 in control and in experimental samples, respectively). Other
n-3 and n-6 fatty acids had similar valuestocontrol samples. The n-
6/n-3 ratio was significantly narrower in the experimental group (6.31
vs. 9.38) but the P/S ratio did not differ betweenthe two groups.In
conclusion calcium soap of linseed oil seems to be a suitable
supplement form of n-3 fatty acids to improve the nutritive value of
lamb meat.
Abstract: Application-Specific Instruction (ASI ) set Processors
(ASIP) have become an important design choice for embedded
systems due to runtime flexibility, which cannot be provided by
custom ASIC solutions. One major bottleneck in maximizing ASIP
performance is the limitation on the data bandwidth between the
General Purpose Register File (GPRF) and ASIs. This paper presents
the Implicit Registers (IRs) to provide the desirable data bandwidth.
An ASI Input/Output model is proposed to formulate the overheads of
the additional data transfer between the GPRF and IRs, therefore,
an IRs allocation algorithm is used to achieve the better performance
by minimizing the number of extra data transfer instructions. The
experiment results show an up to 3.33x speedup compared to the
results without using IRs.
Abstract: Study on suppression of interference in time domain equalizers is attempted for high data rate impulse radio (IR) ultra wideband communication system. The narrow band systems may cause interference with UWB devices as it is having very low transmission power and the large bandwidth. SRAKE receiver improves system performance by equalizing signals from different paths. This enables the use of SRAKE receiver techniques in IRUWB systems. But Rake receiver alone fails to suppress narrowband interference (NBI). A hybrid SRake-MMSE time domain equalizer is proposed to overcome this by taking into account both the effect of the number of rake fingers and equalizer taps. It also combats intersymbol interference. A semi analytical approach and Monte-Carlo simulation are used to investigate the BER performance of SRAKEMMSE receiver on IEEE 802.15.3a UWB channel models. Study on non-line of sight indoor channel models (both CM3 and CM4) illustrates that bit error rate performance of SRake-MMSE receiver with NBI performs better than that of Rake receiver without NBI. We show that for a MMSE equalizer operating at high SNR-s the number of equalizer taps plays a more significant role in suppressing interference.
Abstract: Reliable secure multicast communication in mobile
adhoc networks is challenging due to its inherent characteristics of
infrastructure-less architecture with lack of central authority, high
packet loss rates and limited resources such as bandwidth, time and
power. Many emerging commercial and military applications require
secure multicast communication in adhoc environments. Hence key
management is the fundamental challenge in achieving reliable
secure communication using multicast key distribution for mobile
adhoc networks. Thus in designing a reliable multicast key
distribution scheme, reliability and congestion control over
throughput are essential components. This paper proposes and
evaluates the performance of an enhanced optimized multicast cluster
tree algorithm with destination sequenced distance vector routing
protocol to provide reliable multicast key distribution. Simulation
results in NS2 accurately predict the performance of proposed
scheme in terms of key delivery ratio and packet loss rate under
varying network conditions. This proposed scheme achieves
reliability, while exhibiting low packet loss rate with high key
delivery ratio compared with the existing scheme.
Abstract: The increasing demand for higher data rates in wireless communication systems has led to the more effective and efficient use of all allocated frequency bands. In order to use the whole bandwidth at maximum efficiency, one needs to have RF power amplifiers with a higher linear level and memory-less performance. This is considered to be a major challenge to circuit designers. In this thesis the linearity and memory are studied and examined via the behavior of the intermodulation distortion (IMD). A major source of the in-band distortion can be shown to be influenced by the out-of-band impedances presented at either the input or the output of the device, especially those impedances terminated the low frequency (IF) components. Thus, in order to regulate the in-band distortion, the out of-band distortion must be controllable. These investigations are performed on a 12W LDMOS device characterised at 2.1 GHz within a purpose built, high-power measurement system.
Abstract: Gas Metal Arc Welding (GMAW) processes is an
important joining process widely used in metal fabrication
industries. This paper addresses modeling and optimization of this
technique using a set of experimental data and regression analysis.
The set of experimental data has been used to assess the influence
of GMAW process parameters in weld bead geometry. The
process variables considered here include voltage (V); wire feed
rate (F); torch Angle (A); welding speed (S) and nozzle-to-plate
distance (D). The process output characteristics include weld bead
height, width and penetration. The Taguchi method and regression
modeling are used in order to establish the relationships between
input and output parameters. The adequacy of the model is
evaluated using analysis of variance (ANOVA) technique. In the
next stage, the proposed model is embedded into a Simulated
Annealing (SA) algorithm to optimize the GMAW process
parameters. The objective is to determine a suitable set of process
parameters that can produce desired bead geometry, considering
the ranges of the process parameters. Computational results prove
the effectiveness of the proposed model and optimization
procedure.
Abstract: In this paper, a planar antenna for UWB applications
has been proposed. The antenna consists of a square patch, a partial
ground plane and a slot on the ground plane. The proposed antenna is
easy to be integrated with microwave circuitry for low manufacturing
cost. The flat type antenna has a compact structure and the total size
is 14.5×14.5mm2. The result shows that the impedance bandwidth
(VSWR≤ 2) of the proposed antenna is 12.49 GHz (2.95 to 15.44
GHz), which is equivalent to 135.8%. Details of the proposed
compact planar UWB antenna design is presented and discussed.
Abstract: Currently, there are many local area industrial networks
that can give guaranteed bandwidth to synchronous traffic, particularly
providing CBR channels (Constant Bit Rate), which allow
improved bandwidth management. Some of such networks operate
over Ethernet, delivering channels with enough capacity, specially
with compressors, to integrate multimedia traffic in industrial monitoring
and image processing applications with many sources. In
these industrial environments where a low latency is an essential
requirement, JPEG is an adequate compressing technique but it
generates VBR traffic (Variable Bit Rate). Transmitting VBR traffic
in CBR channels is inefficient and current solutions to this problem
significantly increase the latency or further degrade the quality. In
this paper an R(q) model is used which allows on-line calculation of
the JPEG quantification factor. We obtained increased quality, a lower
requirement for the CBR channel with reduced number of discarded
frames along with better use of the channel bandwidth.
Abstract: In this report, an OTA which is used in fully
differential pipelined ADC was described. Using gain-boost
architecture with difference-ended amplifier, this OTA achieve
high-gain and high-speed. Besides, the CMFB circuit is also used, and
some methods are concerned to improve the performance. Then, by
optimization the layout design, OTA-s mismatch was reduced. This
design was using TSMC 0.18um CMOS process and simulation both
schematic and layout in Cadence. The result of the simulation shows
that the OTA has a gain up to 80dB,a unity gain bandwidth of about
1.437GHz for a 2pF load, a slew rate is about 428V/μs, a output swing
is 0.2V~1.35V, with the power supply of 1.8V, the power
consumption is 88mW. This amplifier was used in a 10bit 150MHz
pipelined ADC.
Abstract: Wavelength multiplexing (WDM) technology along
with optical amplifiers is used for optical communication systems in
S-band, C-band and L-band. To improve the overall system
performance Hybrid amplifiers consisting of cascaded TDFA and
EDFA with different gain bandwidths are preferred for long haul
wavelength multiplexed optical communication systems. This paper
deals with statistical analysis of different configuration of hybrid
amplifier i.e. analysis of TDFA-EDFA configuration and EDFA –
TDFA configuration. In this paper One-Way ANOVA method is used
for statistical analysis.
Abstract: A proposed small-signal model parameters for a pseudomorphic high electron mobility transistor (PHEMT) is presented. Both extrinsic and intrinsic circuit elements of a smallsignal model are determined using genetic algorithm (GA) as a stochastic global search and optimization tool. The parameters extraction of the small-signal model is performed on 200-μm gate width AlGaAs/InGaAs PHEMT. The equivalent circuit elements for a proposed 18 elements model are determined directly from the measured S- parameters. The GA is used to extract the parameters of the proposed small-signal model from 0.5 up to 18 GHz.
Abstract: Image compression is one of the most important
applications Digital Image Processing. Advanced medical imaging
requires storage of large quantities of digitized clinical data. Due to
the constrained bandwidth and storage capacity, however, a medical
image must be compressed before transmission and storage. There
are two types of compression methods, lossless and lossy. In Lossless
compression method the original image is retrieved without any
distortion. In lossy compression method, the reconstructed images
contain some distortion. Direct Cosine Transform (DCT) and Fractal
Image Compression (FIC) are types of lossy compression methods.
This work shows that lossy compression methods can be chosen for
medical image compression without significant degradation of the
image quality. In this work DCT and Fractal Compression using
Partitioned Iterated Function Systems (PIFS) are applied on different
modalities of images like CT Scan, Ultrasound, Angiogram, X-ray
and mammogram. Approximately 20 images are considered in each
modality and the average values of compression ratio and Peak
Signal to Noise Ratio (PSNR) are computed and studied. The quality
of the reconstructed image is arrived by the PSNR values. Based on
the results it can be concluded that the DCT has higher PSNR values
and FIC has higher compression ratio. Hence in medical image
compression, DCT can be used wherever picture quality is preferred
and FIC is used wherever compression of images for storage and
transmission is the priority, without loosing picture quality
diagnostically.
Abstract: Bangla Vowel characterization determines the spectral properties of Bangla vowels for efficient synthesis as well as recognition of Bangla vowels. In this paper, Bangla vowels in isolated word have been analyzed based on speech production model within the framework of Analysis-by-Synthesis. This has led to the extraction of spectral parameters for the production model in order to produce different Bangla vowel sounds. The real and synthetic spectra are compared and a weighted square error has been computed along with the error in the formant bandwidths for efficient representation of Bangla vowels. The extracted features produced good representation of targeted Bangla vowel. Such a representation also plays essential role in low bit rate speech coding and vocoders.
Abstract: Checkpointing is one of the commonly used techniques to provide fault-tolerance in distributed systems so that the system can operate even if one or more components have failed. However, mobile computing systems are constrained by low bandwidth, mobility, lack of stable storage, frequent disconnections and limited battery life. Hence, checkpointing protocols having lesser number of synchronization messages and fewer checkpoints are preferred in mobile environment. There are two different approaches, although not orthogonal, to checkpoint mobile computing systems namely, time-based and index-based. Our protocol is a fusion of these two approaches, though not first of its kind. In the present exposition, an index-based checkpointing protocol has been developed, which uses time to indirectly coordinate the creation of consistent global checkpoints for mobile computing systems. The proposed algorithm is non-blocking, adaptive, and does not use any control message. Compared to other contemporary checkpointing algorithms, it is computationally more efficient because it takes lesser number of checkpoints and does not need to compute dependency relationships. A brief account of important and relevant works in both the fields, time-based and index-based, has also been included in the presentation.
Abstract: We examined whether children ( < 18 years old) had risk of intra-thoracic trauma during 'one-handed' chest compressions through MDCT images. We measured the length of the lower half of the sternum (Stotal/2~X). We also measured the distance from the diaphragm to the midpoint of the sternum (Stotal/2~D) and half the width of an adult hand (Wtotal/2). All the 1 year-old children had Stotal/2~X and Stotal/2~D less than Wtotal/2. Among the children aged 2 years, 6 (60.0%) had Stotal/2~X and Stotal/2~D less than Wtotal/2. Among those aged 3 years, 4 (26.7%) had Stotal/2~X and Stotal/2~D less than Wtotal/2, and among those aged 4 years, 2 (13.3%) had Stotal/2~X and Stotal/2~D less than Wtotal/2. However, Stotal/2~X and Stotal/2~D were greater than Wtotal/2 in children aged 5 years or more. We knew that small children may be at an increased risk of intra-thoracic trauma during 'one-handed' chest compressions.
Abstract: This paper presented a theoretical and numerical investigation of the Compact Antenna Test Range (CATR) equipped with Super Hybrid Modulated Segmented Exponential Serrations (SHMSES). The investigation was based on diffraction theory and, more specifically, the Fresnel diffraction formulation. The CATR provides uniform illumination within the Fresnel region to test antenna. Application of serrated edges has been shown to be a good method to control diffraction at the edges of the reflectors. However, in order to get some insight into the positive effect of serrated edges a less rigorous analysis technique known as Physical Optics (PO) may be used. Ripple free and enhanced quiet zone width are observed for specific values of width and height modulation factors per serrations. The performance of SHMSE serrated reflector is evaluated in order to observe the effects of edge diffraction on the test zone fields.
Abstract: Middle-gate is located in Hasankeyf, Batman dating
back to 1800 BC and is one of the important historical structures in
Turkey. The ancient structure has suffered major structural cracks
due to aging as well as lateral pressure of a cracked rock which is
predicted to be about 100 tons. The existing support system was
found to be inadequate to support the load especially after a recent
rock fall in the close vicinity. Concerns were increased since the
existing support system that is integral with a damaged and cracked
gate wall needed to be replaced by a new support system. The
replacement process must be carefully monitored by crackmeters and
control mechanisms should be integrated to prevent cracks to expand
while the same crack width needs to be maintained after the
operation. The control system and actions taken during the
intervention are explained in this paper.