Abstract: The central recirculation zone (CRZ) in a swirl
stabilized gas turbine combustor has a dominant effect on the fuel air
mixing process and flame stability. Most of state of the art swirlers
share one disadvantage; the fixed swirl number for the same swirler
configuration. Thus, in a mathematical sense, Reynolds number
becomes the sole parameter for controlling the flow characteristics
inside the combustor. As a result, at low load operation, the
generated swirl is more likely to become feeble affecting the flame
stabilization and mixing process. This paper introduces a new swirler
concept which overcomes the mentioned weakness of the modern
configurations. The new swirler introduces air tangentially and
axially to the combustor through tangential vanes and an axial vanes
respectively. Therefore, it provides different swirl numbers for the
same configuration by regulating the ratio between the axial and
tangential flow momenta. The swirler aerodynamic performance was
investigated using four CFD simulations in order to demonstrate the
impact of tangential to axial flow rate ratio on the CRZ. It was found
that the length of the CRZ is directly proportional to the tangential to
axial air flow rate ratio.
Abstract: Natural fibres have emerged as the potential reinforcement material for composites and thus gain attraction by many researchers. This is mainly due to their applicable benefits as they offer low density, low cost, renewable, biodegradability and environmentally harmless and also comparable mechanical properties with synthetic fibre composites. The properties of hybrid composites highly depends on several factors, including the interaction of fillers with the polymeric matrix, shape and size (aspect ratio), and orientation of fillers [1]. In this study, natural fibre kenaf composites and kenaf/fibreglass hybrid composites were fabricated by a combination of hand lay-up method and cold-press method. The effect of different fibre types (powder, short and long) on the tensile properties of composites is investigated. The kenaf composites with and without the addition of fibreglass were then characterized by tensile testing and scanning electron microscopy. A significant improvement in tensile strength and modulus were indicated by the introduction of long kenaf/woven fibreglass hybrid composite. However, the opposite trends are observed in kenaf powder composite. Fractographic observation shows that fibre/matrix debonding causes the fibres pull out. This phenomenon results in the fibre and matrix fracture.
Abstract: Enzymatic hydrolysis is one of the major steps involved in the conversion from sugarcane bagasse to yield ethanol. This process offers potential for yields and selectivity higher, lower energy costs and milder operating conditions than chemical processes. However, the presence of some factors such as lignin content, crystallinity degree of the cellulose, and particle sizes, limits the digestibility of the cellulose present in the lignocellulosic biomasses. Pretreatment aims to improve the access of the enzyme to the substrate. In this study sugarcane bagasse was submitted chemical pretreatment that consisted of two consecutive steps, the first with dilute sulfuric acid (1 % (v/v) H2SO4), and the second with alkaline solutions with different concentrations of NaOH (1, 2, 3 and 4 % (w/v)). Thermal Analysis (TG/ DTG and DTA) was used to evaluate hemicellulose, cellulose and lignin contents in the samples. Scanning Electron Microscopy (SEM) was used to evaluate the morphological structures of the in natura and chemically treated samples. Results showed that pretreatments were effective in chemical degradation of lignocellulosic materials of the samples, and also was possible to observe the morphological changes occurring in the biomasses after pretreatments.
Abstract: This study uses a simulation to establish a realistic
environment for laboratory research on Accountable Care
Organizations. We study network attributes in order to gain insights
regarding healthcare providers- conduct and performance. Our
findings indicate how network structure creates significant
differences in organizational performance. We demonstrate how
healthcare providers positioning themselves at the central, pivotal
point of the network while maintaining their alliances with their
partners produce better outcomes.
Abstract: This work presents a methodology for the selection
and design of propeller oriented to the experimental verification of
theoretical results. The problem of propeller selection and design
usually present itself in the following manner: a certain air volume
and static pressure are required for a certain system. Once the
necessity of fan design on a theoretical basis has been recognized, it
is possible to determinate the dimensions for a fan unit so that it will
perform in accordance with a certain set of specifications. The same
procedures in this work then can be applied in other propeller
selection.
Abstract: A Space Vector based Pulse Width Modulation
control technique for the three-phase PWM converter is proposed in
this paper. The proposed control scheme is based on a synchronous
reference frame model. High performance and efficiency is obtained
with regards to the DC bus voltage and the power factor
considerations of the PWM rectifier thus leading to low losses.
MATLAB/SIMULINK are used as a platform for the simulations and
a SIMULINK model is presented in the paper. The results show that
the proposed model demonstrates better performance and properties
compared to the traditional SPWM method and the method improves
the dynamic performance of the closed loop drastically.
For the Space Vector based Pulse Width Modulation, Sine signal
is the reference waveform and triangle waveform is the carrier
waveform. When the value sine signal is large than triangle signal,
the pulse will start produce to high. And then when the triangular
signals higher than sine signal, the pulse will come to low. SPWM
output will changed by changing the value of the modulation index
and frequency used in this system to produce more pulse width. The
more pulse width produced, the output voltage will have lower
harmonics contents and the resolution increase.
Abstract: Any use of energy in industrial productive activities is combined with various environment impacts. Withintransportation,
this fact was not only found among land transport, railways and maritime transport, but also in the air transport industry. An effective climate protection requires strategies and measures for reducing all
greenhouses gas emissions, in particular carbon dioxide, and must
take into account the economic, ecologic and social aspects. It seem simperative now to develop and manufacture environmentally
friendly products and systems, to reduce consumption and use less
resource, and to save energy and power. Today-sproducts could
better serve these requirements taking into account the integration of
a power management system into the electrical power system.This
paper gives an overview of an approach ofpower management with
load prioritization in modernaircraft. Load dimensioning and load
management strategies on current civil aircraft will be presented and
used as a basis for the proposed approach.
Abstract: This paper presents design and implements a voltage
source inverter type space vector pulse width modulation (SVPWM)
for control a speed of induction motor. This scheme leads to be able
to adjust the speed of the motor by control the frequency and
amplitude of the stator voltage, the ratio of stator voltage to
frequency should be kept constant. The fuzzy logic controller is also
introduced to the system for keeping the motor speed to be constant
when the load varies. The experimental results in testing the 0.22 kW
induction motor from no-load condition to rated condition show the
effectiveness of the proposed control scheme.
Abstract: The robustness of color-based signatures in the presence of a selection of representative distortions is investigated. Considered are five signatures that have been developed and evaluated within a new modular framework. Two signatures presented in this work are directly derived from histograms gathered from video frames. The other three signatures are based on temporal information by computing difference histograms between adjacent frames. In order to obtain objective and reproducible results, the evaluations are conducted based on several randomly assembled test sets. These test sets are extracted from a video repository that contains a wide range of broadcast content including documentaries, sports, news, movies, etc. Overall, the experimental results show the adequacy of color-histogram-based signatures for video fingerprinting applications and indicate which type of signature should be preferred in the presence of certain distortions.
Abstract: One of the major pollutants in the environment is arsenic (As). Due to the toxic effects of As to all organisms, its remediation is necessary. Conventional technologies used in the remediation of As contaminated soils are expensive and may even compromise the structure of the soil. An attractive alternative is phytoremediation, which is the use of plants which can take up the contaminant in their tissues. Plant growth promoting bacteria (PGPB) has been known to enhance growth of plants through several mechanisms such as phytohormone production, phosphate solubilization, siderophore production and 1-aminocyclopropane-1- carboxylate (ACC) deaminase production, which is an essential trait that aids plants especially under stress conditions such as As stress. Twenty one bacteria were isolated from As-contaminated soils in the vicinity of the Janghang Smelter in Chungnam Province, South Korea. These exhibited high tolerance to either arsenite (As III) or arsenate (As V) or both. Most of these isolates possess several plant growth promoting traits which can be potentially exploited to increase phytoremediation efficiency. Among the identified isolates is Pseudomonas sp. JS1215, which produces ACC deaminase, indole acetic acid (IAA), and siderophore. It also has the ability to solubilize phosphate. Inoculation of JS1215 significantly enhanced root and shoot length and biomass accumulation of maize under normal conditions. In the presence of As, particularly in lower As level, inoculation of JS1215 slightly increased root length and biomass. Ethylene increased with increasing As concentration, but was reduced by JS1215 inoculation. JS1215 can be a potential bioinoculant for increasing phytoremediation efficiency.
Abstract: Decentralized Tuple Space (DTS) implements tuple
space model among a series of decentralized hosts and provides the
logical global shared tuple repository. Replication has been introduced
to promote performance problem incurred by remote tuple access. In
this paper, we propose a replication approach of DTS allowing
replication policies self-adapting. The accesses from users or other
nodes are monitored and collected to contribute the decision making.
The replication policy may be changed if the better performance is
expected. The experiments show that this approach suitably adjusts the
replication policies, which brings negligible overhead.
Abstract: Vortices can develop in intakes of turbojet and turbo
fan aero engines during high power operation in the vicinity of solid
surfaces. These vortices can cause catastrophic damage to the engine.
The factors determining the formation of the vortex include both
geometric dimensions as well as flow parameters. It was shown that
the threshold at which the vortex forms or disappears is also
dependent on the initial flow condition (i.e. whether a vortex forms
after stabilised non vortex flow or vice-versa). A computational fluid
dynamics study was conducted to determine the difference in
thresholds between the two conditions. This is the first reported
numerical investigation of the “memory effect". The numerical
results reproduce the phenomenon reported in previous experimental
studies and additional factors, which had not been previously studied,
were investigated. They are the rate at which ambient velocity
changes and the initial value of ambient velocity. The former was
found to cause a shift in the threshold but not the later. It was also
found that the varying condition thresholds are not symmetrical about
the neutral threshold. The vortex to no vortex threshold lie slightly
further away from the neutral threshold compared to the no vortex to
vortex threshold. The results suggests that experimental investigation
of vortex formation threshold performed either in vortex to no vortex
conditions, or vice versa, solely may introduce mis-predictions
greater than 10%.
Abstract: Software Reusability is primary attribute of software
quality. There are metrics for identifying the quality of reusable
components but the function that makes use of these metrics to find
reusability of software components is still not clear. These metrics if
identified in the design phase or even in the coding phase can help us
to reduce the rework by improving quality of reuse of the component
and hence improve the productivity due to probabilistic increase in
the reuse level. In this paper, we have devised the framework of
metrics that uses McCabe-s Cyclometric Complexity Measure for
Complexity measurement, Regularity Metric, Halstead Software
Science Indicator for Volume indication, Reuse Frequency metric
and Coupling Metric values of the software component as input
attributes and calculated reusability of the software component. Here,
comparative analysis of the fuzzy, Neuro-fuzzy and Fuzzy-GA
approaches is performed to evaluate the reusability of software
components and Fuzzy-GA results outperform the other used
approaches. The developed reusability model has produced high
precision results as expected by the human experts.
Abstract: L-asparaginase was extracted from pathogenic
Escherichia coli which was isolated from urinary tract infection
patients. L-asparaginase was purified 96-fold by ultrafiltration, ion
exchange and gel filtration giving 39.19% yield with final specific
activity of 178.57 IU/mg. L-asparaginase showed 138,356±1,000
Dalton molecular weight with 31024±100 Dalton molecular mass.
Kinetic properties of enzyme resulting 1.25×10-5 mM Km and
2.5×10-3 M/min Vmax. L-asparaginase showed a maximum activity
at pH 7.5 when incubated at 37 ºC for 30 min and illustrated its full
activity (100%) after 15 min incubation at 20-37 ºC, while 70% of its
activity was lost when incubated at 60 ºC. L-asparaginase showed
cytotoxicity to U937 cell line with IC50 0.5±0.19 IU/ml, and
selectivity index (SI=7.6) about 8 time higher selectivity over the
lymphocyte cells. Therefore, the local pathogenic E. coli strains may
be used as a source of high yield of L-asparaginase to produce anti
cancer agent with high selectivity.
Abstract: In the 1980s, companies began to feel the effect of three major influences on their product development: newer and innovative technologies, increasing product complexity and larger organizations. And therefore companies were forced to look for new product development methods. This paper tries to focus on the two of new product development methods (DFM and CE). The aim of this paper is to see and analyze different product development methods specifically on Design for Manufacturability and Concurrent Engineering. Companies can achieve and be benefited by minimizing product life cycle, cost and meeting delivery schedule. This paper also presents simplified models that can be modified and used by different companies based on the companies- objective and requirements. Methodologies that are followed to do this research are case studies. Two companies were taken and analysed on the product development process. Historical data, interview were conducted on these companies in addition to that, Survey of literatures and previous research works on similar topics has been done during this research. This paper also tries to show the implementation cost benefit analysis and tries to calculate the implementation time. From this research, it has been found that the two companies did not achieve the delivery time to the customer. Some of most frequently coming products are analyzed and 50% to 80 % of their products are not delivered on time to the customers. The companies are following the traditional way of product development that is sequentially design and production method, which highly affect time to market. In the case study it is found that by implementing these new methods and by forming multi disciplinary team in designing and quality inspection; the company can reduce the workflow steps from 40 to 30.
Abstract: This paper has, as its point of departure, the foundational
axiomatic theory of E. De Giorgi (1996, Scuola Normale
Superiore di Pisa, Preprints di Matematica 26, 1), based on two
primitive notions of quality and relation. With the introduction of
a unary relation, we develop a system totally based on the sole
primitive notion of relation. Such a modification enables a definition
of the concept of dynamic unary relation. In this way we construct a
simple language capable to express other well known theories such
as Robinson-s arithmetic or a piece of a theory of concatenation. A
key role in this system plays an abstract relation designated by “( )",
which can be interpreted in different ways, but in this paper we will
focus on the case when we can perform computations and obtain
results.
Abstract: Mostly transforms are used for speech data
compressions which are lossy algorithms. Such algorithms are
tolerable for speech data compression since the loss in quality is not
perceived by the human ear. However the vector quantization (VQ)
has a potential to give more data compression maintaining the same
quality. In this paper we propose speech data compression algorithm
using vector quantization technique. We have used VQ algorithms
LBG, KPE and FCG. The results table shows computational
complexity of these three algorithms. Here we have introduced a new
performance parameter Average Fractional Change in Speech
Sample (AFCSS). Our FCG algorithm gives far better performance
considering mean absolute error, AFCSS and complexity as
compared to others.
Abstract: A packet analyzer is a tool for debugging sensor
network systems and is convenient for developers. In this paper, we
introduce a new packet analyzer based on an embedded system. The
proposed packet analyzer is compatible with IEEE 802.15.4, which is
suitable for the wireless communication standard for sensor networks,
and is available for remote control by adopting a server-client scheme
based on the Ethernet interface. To confirm the operations of the
packet analyzer, we have developed two types of sensor nodes based
on PIC4620 and ATmega128L microprocessors and tested the
functions of the proposed packet analyzer by obtaining the packets
from the sensor nodes.
Abstract: In this paper, several improvements are proposed to
previous work of automated classification of alcoholics and nonalcoholics.
In the previous paper, multiplayer-perceptron neural
network classifying energy of gamma band Visual Evoked Potential
(VEP) signals gave the best classification performance using 800
VEP signals from 10 alcoholics and 10 non-alcoholics. Here, the
dataset is extended to include 3560 VEP signals from 102 subjects:
62 alcoholics and 40 non-alcoholics. Three modifications are
introduced to improve the classification performance: i) increasing
the gamma band spectral range by increasing the pass-band width of
the used filter ii) the use of Multiple Signal Classification algorithm
to obtain the power of the dominant frequency in gamma band VEP
signals as features and iii) the use of the simple but effective knearest
neighbour classifier. To validate that these two modifications
do give improved performance, a 10-fold cross validation
classification (CVC) scheme is used. Repeat experiments of the
previously used methodology for the extended dataset are performed
here and improvement from 94.49% to 98.71% in maximum
averaged CVC accuracy is obtained using the modifications. This
latest results show that VEP based classification of alcoholics is
worth exploring further for system development.
Abstract: The ionization energy in semiconductor
systems in nano scale was investigated by using effective mass
approximation. By introducing the Hamiltonian of the system, the
variational technique was employed to calculate the ground state and
the ionization energy of a donor at the center and in the case that the
impurities are randomly distributed inside a cubic quantum well. The
numerical results for GaAs/GaAlAs show that the ionization energy
strongly depends on the well width for both cases and it decreases as
the well width increases. The ionization energy of a quantum wire
was also calculated and compared with the results for the well.