Abstract: At present, it is very common to find renewable
energy resources, especially wind power, connected to distribution
systems. The impact of this wind power on voltage distribution levels
has been addressed in the literature. The majority of this works deals
with the determination of the maximum active and reactive power
that is possible to be connected on a system load bus, until the
voltage at that bus reaches the voltage collapse point. It is done by the
traditional methods of PV curves reported in many references.
Theoretical expression of maximum power limited by voltage
stability transfer through a grid is formulated using an exact
representation of distribution line with ABCD parameters. The
expression is used to plot PV curves at various power factors of a
radial system. Limited values of reactive power can be obtained. This
paper presents a method to study the relationship between the active
power and voltage (PV) at the load bus to identify the voltage
stability limit. It is a foundation to build a permitted working
operation region in complying with the voltage stability limit at the
point of common coupling (PCC) connected wind farm.
Abstract: An attempt has been made to investigate the
machinability of zirconia toughened alumina (ZTA) inserts while
turning AISI 4340 steel. The insert was prepared by powder
metallurgy process route and the machining experiments were
performed based on Response Surface Methodology (RSM) design
called Central Composite Design (CCD). The mathematical model of
flank wear, cutting force and surface roughness have been developed
using second order regression analysis. The adequacy of model has
been carried out based on Analysis of variance (ANOVA) techniques.
It can be concluded that cutting speed and feed rate are the two most
influential factor for flank wear and cutting force prediction. For
surface roughness determination, the cutting speed & depth of cut
both have significant contribution. Key parameters effect on each
response has also been presented in graphical contours for choosing
the operating parameter preciously. 83% desirability level has been
achieved using this optimized condition.
Abstract: In this paper a computer system for electromagnetic
properties measurements is designed. The system employs Agilent
4294A precision impedance analyzer to measure the amplitude and
the phase of a signal applied over a tested biological tissue sample.
Measured by the developed computer system data could be used for
tissue characterization in wide frequency range from 40Hz to
110MHz. The computer system can interface with output devices
acquiring flexible testing process.
Abstract: True stress-strain curve of railhead steel is required to
investigate the behaviour of railhead under wheel loading through elasto-plastic Finite Element (FE) analysis. To reduce the rate of wear, the railhead material is hardened through annealing and
quenching. The Australian standard rail sections are not fully hardened and hence suffer from non-uniform distribution of the
material property; usage of average properties in the FE modelling can potentially induce error in the predicted plastic strains. Coupons
obtained at varying depths of the railhead were, therefore, tested under axial tension and the strains were measured using strain gauges as well as an image analysis technique, known as the Particle Image Velocimetry (PIV). The head hardened steel exhibit existence of three distinct zones of yield strength; the yield strength as the ratio of the average yield strength provided in the standard (σyr=780MPa) and
the corresponding depth as the ratio of the head hardened zone along
the axis of symmetry are as follows: (1.17 σyr, 20%), (1.06 σyr, 20%-80%) and (0.71 σyr, > 80%). The stress-strain curves exhibit limited plastic zone with fracture occurring at strain less than 0.1.
Abstract: The experimental design was 4 x 5 factorial with three
replications in fully controlled research greenhouse in Department of
Soil Sciences and Plant Nutrition, Faculty of Agriculture, University
of Selcuk in the year of 2009. Determination of tolerant chickpea
genotypes to drought was made in the research. Additionally,
sophisticated effects of drought on plant growth and development,
biochemical and physical properties or physical defense mechanisms
were presented. According to the results, the primary genotypes were
Ilgın YP (0.0063 g/gh) for leaf water capacity, 22235 70.44(%) for
relative water content, 22159 (82.47%) for real water content,
22159 (5.03 mg/l) for chlorophyll a+b, Ilgın YP (125.89 nmol
H2O2.dak-1/ mg protein-1) for peroxidase, Yunak YP (769.67
unit/ mg protein-1) for superoxide dismutase, Seydişehir YP
(16.74 μg.TA-1) for proline, Gökçe (80.01 nmol H2O2.dak-1/ mg
protein-1) for catalase. Consequently, all the genotypes
increased their enzyme activity depending on the increasing of
drought stress consider with the effects of drought stress on leaf
enzyme activity. Chickpea genotypes are increasing enzyme
activity against to drought stress.
Abstract: Phytophthora cinnamomi (P. c) is a plant pathogenic
oomycete that is capable of damaging plants in commercial production
systems and natural ecosystems worldwide. The most common
methods for the detection and diagnosis of P. c infection are
expensive, elaborate and time consuming. This study was carried out
to examine whether species specific and life cycle specific volatile
organic compounds (VOCs) can be absorbed by solid-phase
microextraction fibers and detected by gas chromatography that are
produced by P. c and another oomycete Pythium dissotocum. A
headspace solid-phase microextraction (HS-SPME) together with gas
chromatography (GC) method was developed and optimized for the
identification of the VOCs released by P. c. The optimized parameters
included type of fiber, exposure time, desorption temperature and
desorption time. Optimization was achieved with the analytes of P.
c+V8A and V8A alone. To perform the HS-SPME, six types of fiber
were assayed and compared: 7μm Polydimethylsiloxane (PDMS),
100μm Polydimethylsiloxane (PDMS), 50/30μm
Divinylbenzene/CarboxenTM/Polydimethylsiloxane
DVB/CAR/PDMS), 65μm Polydimethylsiloxane/Divinylbenzene
(PDMS/DVB), 85μm Polyacrylate (PA) fibre and 85μm CarboxenTM/
Polydimethylsiloxane (Carboxen™/PDMS). In a comparison of the
efficacy of the fibers, the bipolar fiber DVB/CAR/PDMS had a higher
extraction efficiency than the other fibers. An exposure time of 16h
with DVB/CAR/PDMS fiber in the sample headspace was enough to
reach the maximum extraction efficiency. A desorption time of 3min
in the GC injector with the desorption temperature of 250°C was
enough for the fiber to desorb the compounds of interest. The chromatograms and morphology study confirmed that the VOCs from
P. c+V8A had distinct differences from V8A alone, as did different
life cycle stages of P. c and different taxa such as Pythium dissotocum.
The study proved that P. c has species and life cycle specific VOCs,
which in turn demonstrated the feasibility of this method as means of
Abstract: Higher capacities of power plants together with
increased awareness on environmental considerations have led to
taller height of stacks. It is seen that strong wind can result in falling
of stacks. So, aerodynamic consideration of stacks is very important
in order to save the falling of stacks. One stack is not enough in
industries and power sectors and two or three stacks are required for
proper operation of the unit. It is very important to arrange the stacks
in proper way to resist their downfall. The present experimental
study concentrates on the mutual effect of three nearby stacks on
each other at three different arrangements, viz. linear, side-by-side
and triangular. The experiments find out the directions of resultant
forces acting on the stacks in different configurations so that proper
arrangement of supports can be made with respect to the wind
directionality obtained from local meteorological data. One can also
easily ascertain which stack is more vulnerable to wind in
comparison to the others for a particular configuration. Thus, this
study is important in studying the effect of wind force on three stacks
in different arrangements and is very helpful in placing the supports
in proper places in order to avoid failing of stack-like structures due
to wind.
Abstract: This paper presents a new study on the applications of
optimization and regression analysis techniques for optimal
calculation of partial ratios of four-step helical gearboxes for getting
minimal gearbox length. In the paper, basing on the moment
equilibrium condition of a mechanic system including four gear units
and their regular resistance condition, models for determination of the
partial ratios of the gearboxes are proposed. In particular, explicit
models for calculation of the partial ratios are proposed by using
regression analysis. Using these models, the determination of the
partial ratios is accurate and simple.
Abstract: In this paper we present a novel error model for
packet loss and subsequent error description. The proposed model
simulates the error performance of wireless communication link. The
model is designed as two independent Markov chains, where the first
one is used for packet generation and the second one generates
correctly and incorrectly transmitted bits for received packets from
the first chain. The statistical analyses of real communication on the
wireless link are used for determination of model-s parameters. Using
the obtained parameters and the implementation of the generator, we
collected generated traffic. The obtained results generated by
proposed model are compared with the real data collection.
Abstract: In Blind Source Separation (BSS) processing, taking
advantage of scaling factor indetermination and based on the floatingpoint
representation, we propose a scaling technique applied to the
separation matrix, to avoid the saturation or the weakness in the
recovered source signals. This technique performs an Automatic Gain
Control (AGC) in an on-line BSS environment. We demonstrate
the effectiveness of this technique by using the implementation of
a division free BSS algorithm with two input, two output. This
technique is computationally cheaper and efficient for a hardware
implementation.
Abstract: In the present paper, Fatigue life assessment of an
anti-roll bar component of a passenger vehicle, is investigated by
ANSYS 11 software. A stress analysis is also carried out by the
finite element technique for the determination of highly stressed
regions on the bar. Anti-roll bar is a suspension element used at the
front, rear, or at both ends of a car that reduces body roll by resisting
any unequal vertical motion between the pair of wheels to which it is
connected. As a first stage, fatigue damage models proposed by some
well-known references and the corresponding assumptions are
discussed and some enhancements are proposed. Then, fracture
analysis of an anti-roll bar of an automobile is carried out. The
analysed type of the anti-roll bar is especially important as many
cases are reported about the fracture after a 100,000 km of travel
fatigue and fracture conditions. This paper demonstrates fatigue life
of an anti-roll bar and then evaluated by experimental analytically
results from other researcher.
Abstract: Industrial robots play a vital role in automation
however only little effort are taken for the application of robots in
machining work such as Grinding, Cutting, Milling, Drilling,
Polishing etc. Robot parallel manipulators have high stiffness,
rigidity and accuracy, which cannot be provided by conventional
serial robot manipulators. The aim of this paper is to perform the
modeling and the workspace analysis of a 3 DOF Parallel
Manipulator (3 DOF PM). The 3 DOF PM was modeled and
simulated using 'ADAMS'. The concept involved is based on the
transformation of motion from a screw joint to a spherical joint
through a connecting link. This paper work has been planned to
model the Parallel Manipulator (PM) using screw joints for very
accurate positioning. A workspace analysis has been done for the
determination of work volume of the 3 DOF PM. The position of the
spherical joints connected to the moving platform and the
circumferential points of the moving platform were considered for
finding the workspace. After the simulation, the position of the joints
of the moving platform was noted with respect to simulation time and
these points were given as input to the 'MATLAB' for getting the
work envelope. Then 'AUTOCAD' is used for determining the work
volume. The obtained values were compared with analytical
approach by using Pappus-Guldinus Theorem. The analysis had been
dealt by considering the parameters, link length and radius of the
moving platform. From the results it is found that the radius of
moving platform is directly proportional to the work volume for a
constant link length and the link length is also directly proportional
to the work volume, at a constant radius of the moving platform.
Abstract: In this research, Forming Limit Diagrams for supertension
sheet metals which are using in automobile industry have
been obtained. The exerted strains to sheet metals have been
measured with four different methods and the errors of each method
have also been represented. These methods have been compared with
together and the most efficient and economic way of extracting of the
exerted strains to sheet metals has been introduced. In this paper total
error and uncertainty of FLD extraction procedures have been
derived. Determination of the measurement uncertainty in extracting
of FLD has a great importance in design and analysis of the sheet
metal forming process.
Abstract: Most fingerprint recognition techniques are based on minutiae matching and have been well studied. However, this technology still suffers from problems associated with the handling of poor quality impressions. One problem besetting fingerprint matching is distortion. Distortion changes both geometric position and orientation, and leads to difficulties in establishing a match among multiple impressions acquired from the same finger tip. Marking all the minutiae accurately as well as rejecting false minutiae is another issue still under research. Our work has combined many methods to build a minutia extractor and a minutia matcher. The combination of multiple methods comes from a wide investigation into research papers. Also some novel changes like segmentation using Morphological operations, improved thinning, false minutiae removal methods, minutia marking with special considering the triple branch counting, minutia unification by decomposing a branch into three terminations, and matching in the unified x-y coordinate system after a two-step transformation are used in the work.
Abstract: Drought is natural and climate phenomenon and in fact server as a part of climate in an area and also it has significant environmental, social ,and economic consequences .drought differs from the other natural disasters from this viewpoint that it s a creeping phenomenon meaning that it progresses little and its difficult to determine the time of its onset and termination .most of the drought definitions are on based on precipitation shortage and consequently ,the shortage of water some of the activities related to the water such as agriculture In this research ,drought condition in Fars province was evacuated using SPI method within a 37 year – statistical –period(1974-2010)and maps related to the drought were prepared for each of the statistical period years. According to the results obtained from this research, the years 1974, 1976, 1975, 1982 with SPI (-1.03, 0.39, -1.05, -1.49) respectively, were the doughiest years and 1996,1997,2000 with SPI (2.49, 1.49, 1.46, 1.04) respectively, the most humid within the studying time series and the rest are in more normal conditions in the term of drought.
Abstract: Tubular process equipment is often damaged in
industrial processes. The damage occurs both on devices working at
high temperatures and also on less exposed devices. In case of sudden
damage of key equipment a shutdown of the whole production unit
and resulting significant economic losses are imminent. This paper
presents a solution of several types of tubular process equipment. The
causes of damage and suggestions of correction actions are discussed
in all cases. Very important part is the analysis of operational
conditions, determination of unfavourable working states decreasing
lifetime of devices and suggestions of correction actions. Lately very
popular numerical methods are used for analysis of the equipment.
Abstract: The aim of this paper is to introduce a parametric
distribution model in fatigue life reliability analysis dealing with
variation in material properties. Service loads in terms of responsetime
history signal of Belgian pave were replicated on a multi-axial
spindle coupled road simulator and stress-life method was used to
estimate the fatigue life of automotive stub axle. A PSN curve was
obtained by monotonic tension test and two-parameter Weibull
distribution function was used to acquire the mean life of the
component. A Pearson system was developed to evaluate the fatigue
life reliability by considering stress range intercept and slope of the
PSN curve as random variables. Considering normal distribution of
fatigue strength, it is found that the fatigue life of the stub axle to
have the highest reliability between 10000 – 15000 cycles. Taking
into account the variation of material properties associated with the
size effect, machining and manufacturing conditions, the method
described in this study can be effectively applied in determination of
probability of failure of mass-produced parts.
Abstract: The paper presents the results of theoretical and
numerical modeling of propagation of shock waves in bubbly liquids
related to nonlinear effects (realistic equation of state, chemical
reactions, two-dimensional effects). On the basis on the Rankine-
Hugoniot equations the problem of determination of parameters of
passing and reflected shock waves in gas-liquid medium for
isothermal, adiabatic and shock compression of the gas component is
solved by using the wide-range equation of state of water in the
analitic form. The phenomenon of shock wave intensification is
investigated in the channel of variable cross section for the
propagation of a shock wave in the liquid filled with bubbles
containing chemically active gases. The results of modeling of the
wave impulse impact on the solid wall covered with bubble layer are
presented.
Abstract: Protein structure determination and prediction has
been a focal research subject in the field of bioinformatics due to the
importance of protein structure in understanding the biological and
chemical activities of organisms. The experimental methods used by
biotechnologists to determine the structures of proteins demand
sophisticated equipment and time. A host of computational methods
are developed to predict the location of secondary structure elements
in proteins for complementing or creating insights into experimental
results. However, prediction accuracies of these methods rarely
exceed 70%.
Abstract: Aldehydes as secondary lipid oxidation products are highly specific to the oxidative degradation of particular polyunsaturated fatty acids present in foods. Gas chromatographic analysis of those volatile compounds has been widely used for monitoring of the deterioration of food products. Developed static headspace gas chromatography method using flame ionization detector (SHS GC FID) was applied to monitor the aldehydes present in processed foods such as bakery, meat and confectionary products.
Five selected aldehydes were determined in samples without any sample preparation, except grinding for bakery and meat products. SHS–GC analysis allows the separation of propanal, pentanal, hexanal, heptanal and octanal, within 15min. Aldehydes were quantified in fresh and stored samples, and the obtained range of aldehydes in crackers was 1.62±0.05 – 9.95±0.05mg/kg, in sausages 6.62±0.46 – 39.16±0.39mg/kg; and in cocoa spread cream 0.48±0.01 – 1.13±0.02mg/kg. Referring to the obtained results, the following can be concluded, proposed method is suitable for different types of samples, content of aldehydes varies depending on the type of a sample, and differs in fresh and stored samples of the same type.