Abstract: Treatment of tar-containing wastewater is necessary
for the successful operation of biomass gasification plants (BGPs). In
the present study, tar-containing wastewater was treated using lime
and alum for the removal of in-organics, followed by adsorption on
powdered activated carbon (PAC) for the removal of organics. Limealum
experiments were performed in a jar apparatus and activated
carbon studies were performed in an orbital shaker. At optimum
concentrations, both lime and alum individually proved to be capable
of removing color, total suspended solids (TSS) and total dissolved
solids (TDS), but in both cases, pH adjustment had to be carried out
after treatment. The combination of lime and alum at the dose ratio
of 0.8:0.8 g/L was found to be optimum for the removal of inorganics.
The removal efficiency achieved at optimum
concentrations were 78.6, 62.0, 62.5 and 52.8% for color, alkalinity,
TSS and TDS, respectively. The major advantages of the lime-alum
combination were observed to be as follows: no requirement of pH
adjustment before and after treatment and good settleability of
sludge. Coagulation-precipitation followed by adsorption on PAC
resulted in 92.3% chemical oxygen demand (COD) removal and
100% phenol removal at equilibrium. Ammonia removal efficiency
was found to be 11.7% during coagulation-flocculation and 36.2%
during adsorption on PAC. Adsorption of organics on PAC in terms
of COD and phenol followed Freundlich isotherm with Kf = 0.55 &
18.47 mg/g and n = 1.01 & 1.45, respectively. This technology may
prove to be one of the fastest and most techno-economically feasible
methods for the treatment of tar-containing wastewater generated
from BGPs.
Abstract: The major source of allergy in home is the house dust
mite (Dematophagoides farina, Dermatophagoides pteronyssinus)
causing allergic symptom include atopic dermatitis, asthma, perennial
rhinitis and even infant death syndrome.
Control of this mite species is dependent on the use of chemical
methods such as fumigation treatments with methylene bromide,
spraying with organophosphates such as pirimiphos-methyl, or
treatments with repellents such as DEET and benzyl benzoate.
Although effective, their repeated use for decades has sometimes
resulted in development of resistance and fostered environmental and
human health concerns. Both decomposing animal parts and the
protein that surrounds mite fecal pellets cause mite allergy. So it is
more effective to repel than to kill them because allergen is not living
house dust mite but dead body or fecal particles of house dust mite.
It is important to find out natural repellent material against house
dust mite to control them and reduce the allergic reactions. Plants may
be an alternative source for dust mite control because they contain a
range of bioactive chemicals.
The research objectives of this paper were to verify the acaricidal
and repellent effects of cinnamon essential oil and to find out it-s most
effective concentrations. We could find that cinnamon bark essential
oil was very effective material to control the house dust mite.
Furthermore, it could reduce chemical resistance and danger for
human health.
Abstract: The alternative technique for sterilization of culture
medium to replace autoclaving was carried out. For sterilization of
culture medium without autoclaving, some commercial pure essential
oils, bergamot oil, betel oil, cinnamon oil, lavender oil and turmeric
oil, were tested alone or in combinations with some disinfectants,
10% povidone-iodine and 2% iodine + 2.4% potassium iodide. Each
essential oil or combination was added to 25-mL Murashige and
Skoog (MS) medium before medium was solidified in a 120-mL
container, kept for 2 weeks before evaluating sterile conditions.
Treated media, supplemented with essential oils, were compared to
control medium, autoclaved at 121 degree Celsius for 15 min. In
vitro sterile conditions were found 20 – 100% from these treated
media compared to 100% sterile condition from autoclaved medium.
Treated media obtained 100% sterile conditions were chosen for
culturing chrysanthemum shoots. It was found that 10% povidoneiodine
in combination with cinnamon oil (3:1) and 2% iodine + 2.4%
potassium iodide in combination with lavender oil (1:3) at the
concentration of 36 3L/25 mL medium provided the promising
growth of shoot explants.
Abstract: Cabbage seedlings grown in vitro were exposed to
excess levels of heavy metals, including Cd, Mo, and Zn. High metal
levels affected plant growth at cotyledonary stage. Seedlings under
Cd, Mo, and Zn treatments could not produce root hairs and true
leaves. Under stress conditions, seedlings accumulated a higher
amount of anthocyanins in their cotyledons than those in the control.
The pigments isolated from Cd and Zn stressed seedling cotyledons
appeared as pink, while under Mo stress, was dark pink or purple.
Moreover, excess Mo stress increased antioxidant enzyme activities
of APX, CAT, SOD. These results suggest that, under excess Mo
stress, the induced antioxidant enzyme activity of cabbage seedlings
may function as a protective mechanism to shield the plants from
toxicity and exacerbated growth.
Abstract: Phytophthora cinnamomi (P. c) is a plant pathogenic
oomycete that is capable of damaging plants in commercial production
systems and natural ecosystems worldwide. The most common
methods for the detection and diagnosis of P. c infection are
expensive, elaborate and time consuming. This study was carried out
to examine whether species specific and life cycle specific volatile
organic compounds (VOCs) can be absorbed by solid-phase
microextraction fibers and detected by gas chromatography that are
produced by P. c and another oomycete Pythium dissotocum. A
headspace solid-phase microextraction (HS-SPME) together with gas
chromatography (GC) method was developed and optimized for the
identification of the VOCs released by P. c. The optimized parameters
included type of fiber, exposure time, desorption temperature and
desorption time. Optimization was achieved with the analytes of P.
c+V8A and V8A alone. To perform the HS-SPME, six types of fiber
were assayed and compared: 7μm Polydimethylsiloxane (PDMS),
100μm Polydimethylsiloxane (PDMS), 50/30μm
Divinylbenzene/CarboxenTM/Polydimethylsiloxane
DVB/CAR/PDMS), 65μm Polydimethylsiloxane/Divinylbenzene
(PDMS/DVB), 85μm Polyacrylate (PA) fibre and 85μm CarboxenTM/
Polydimethylsiloxane (Carboxen™/PDMS). In a comparison of the
efficacy of the fibers, the bipolar fiber DVB/CAR/PDMS had a higher
extraction efficiency than the other fibers. An exposure time of 16h
with DVB/CAR/PDMS fiber in the sample headspace was enough to
reach the maximum extraction efficiency. A desorption time of 3min
in the GC injector with the desorption temperature of 250°C was
enough for the fiber to desorb the compounds of interest. The chromatograms and morphology study confirmed that the VOCs from
P. c+V8A had distinct differences from V8A alone, as did different
life cycle stages of P. c and different taxa such as Pythium dissotocum.
The study proved that P. c has species and life cycle specific VOCs,
which in turn demonstrated the feasibility of this method as means of
Abstract: The effect of plant growth-promoting rhizobacteria
(PGPR) on seed germination, seedling growth and yield of field
grown maize were evaluated in three experiments. In these
experiments six bacterial strains include P.putida strain R-168,
P.fluorescens strain R-93, P.fluorescens DSM 50090, P.putida
DSM291, A.lipoferum DSM 1691, A.brasilense DSM 1690 were
used. Results of first study showed seed Inoculation significantly
enhanced seed germination and seedling vigour of maize. In second
experiment, leaf and shoot dry weight and also leaf surface area
significantly were increased by bacterial inoculation in both sterile
and non-sterile soil. The results showed that inoculation with
bacterial treatments had a more stimulating effect on growth and
development of plants in nonsterile than sterile soil. In the third
experiment, Inoculation of maize seeds with all bacterial strains
significantly increased plant height, 100 seed weight, number of seed
per ear and leaf area .The results also showed significant increase in
ear and shoot dry weight of maize.
Abstract: Higher capacities of power plants together with
increased awareness on environmental considerations have led to
taller height of stacks. It is seen that strong wind can result in falling
of stacks. So, aerodynamic consideration of stacks is very important
in order to save the falling of stacks. One stack is not enough in
industries and power sectors and two or three stacks are required for
proper operation of the unit. It is very important to arrange the stacks
in proper way to resist their downfall. The present experimental
study concentrates on the mutual effect of three nearby stacks on
each other at three different arrangements, viz. linear, side-by-side
and triangular. The experiments find out the directions of resultant
forces acting on the stacks in different configurations so that proper
arrangement of supports can be made with respect to the wind
directionality obtained from local meteorological data. One can also
easily ascertain which stack is more vulnerable to wind in
comparison to the others for a particular configuration. Thus, this
study is important in studying the effect of wind force on three stacks
in different arrangements and is very helpful in placing the supports
in proper places in order to avoid failing of stack-like structures due
to wind.
Abstract: Currently, a large number of license activities (Early
Site Permits, Combined Operating License, reactor certifications,
etc.), are pending for review before the United States Nuclear
Regulatory Commission (US NRC). Much of the senior staff at the
NRC is now committed to these review and licensing actions. To
address this additional workload, the NRC has recruited a large
number of new Regulatory Staff for dealing with these and other
regulatory actions such as the US Fleet of Research and Test Reactors
(RTRs). These reactors pose unusual demands on Regulatory Staff
since the US Fleet of RTRs, although few (32 Licensed RTRs as of
2010), they represent a broad range of reactor types, operations, and
research and training aspects that nuclear reactor power plants (such
as the 104 LWRs) do not pose. The NRC must inspect and regulate
all these facilities. This paper addresses selected training topics and
regulatory activities providedNRC Inspectors for RTRs.
Abstract: In order to evaluate the Effects of dual inoculation of
Azotobacter and Mycorrhiza with Nitrogen and Phosphorus levels on
yield and yield components of spring safflower, this study was
carried out in field of Farahan university in Markazi province in
2007. A factorial in a randomized complete block design with three
replications was used inoculation of Azotobacter (with inoculation
and without inoculation) and Mycorrhiza (with inoculation and
without inoculation ) with Nitrogen and Phosphorus levels [F0= N0+
P0 (kg.ha-1), F1= N50+ P25(kg.ha-1), F2= N100+ P50(kg.ha-1) and
F3= N150+ P75 (kg.ha-1)] on spring safflower (cultivar IL-111). In
this study characteristics such as: Harvest index, Hectolitre weight,
Root dry weight, Seed yield, Mycorrhizal Colonization Root,
Number of days to maturity were assessed. Results indicated that
treatment (A0M1F3) with grain yield (1556 kg.ha-1) and treatment
(A0M1F0) with grain yield (918 kg.ha-1) were significantly superior
to the other treatments and according to calculated, inoculation seeds
in plantig date with Azotobacter and Mycorrhiza to cause increase
grain yield about 5/38 percentage. we can by inoculation safflower
seeds with Azotobacter and Mycorrhiza too easily at the time sowing
date. The purpose of this research, study and evaluation the role of
biological fixation N and P, to provide for feeds plants.
Abstract: Green Roofs offers numerous advantages, including lowering ambient temperature, which is of increasing interest due to global warming concerns. However, there are technical problems pertaining to waterproofing to be resolved. Currently, the only recognized green roof waterproofing test is the German standard FLL. This paper examines the potential of replicating the test in tropical climate and reducing the test duration by using pre-grown plants. A three year old sample and a new setup were used for this experimental study. The new setup was prepared with close reference to the FLL standards and was compared against the three year old sample. Results showed that the waterproofing membrane was damaged by plant roots in both setups. Joints integrity was also challenged.
Abstract: Carbon steel is used in boilers, pressure vessels, heat
exchangers, piping, structural elements and other moderatetemperature
service systems in which good strength and ductility are
desired. ASME Boiler and Pressure Vessel Code, Section II Part A
(2004) provides specifications of ferrous materials for construction of
pressure equipment, covering wide range of mechanical properties
including high strength materials for power plants application.
However, increased level of springback is one of the major problems
in fabricating components of high strength steel using bending.
Presented work discuss the springback simulations for five different
steels (i.e. SA-36, SA-299, SA-515 grade 70, SA-612 and SA-724
grade B) using finite element analysis of air V-bending. Analytical
springback simulations of hypothetical layered materials are
presented. Result shows that; (i) combination of the material property
parameters controls the springback, (ii) layer of the high ductility
steel on the high strength steel greatly suppresses the springback.
Abstract: A pot experiment was carried out under controlled
conditions to evaluate the residual effects of different doses of
atrazine+alachlor and foramsulfuron used in corn fields on the
growth and physiology of rapeseed (Brassica napus L.). A split-plot
experiment in CRD with 4 replications was used. The main plots
consisted of herbicide type (atrazine+alachlor mixture and
foramsulfuron) and the sub-plots were different residual doses of the
herbicides (0, 1%, 5%, 10%, 20%, 40%, 50% and 100%). 7 cm
diameter pots were filled with a virgin soil and seeds of rapeseed cv.
Hayola were planted in them. The pots were kept under controlled
conditions for 8 weeks after germination. At harvest, the growth
parameters and the chlorophyll contents of the leaves were
determined. The results showed that the growth of rapeseed plants
was completely prevented at the highest residual doses of the
herbicides (50 and 100 %). The growth parameters of rapeseed plants
were affected by all doses of both types of the herbicide as compared
to the controls. The residual effects of atrazine+alachlor mixture in
reducing the growth parameters of rapeseed were more pronounced
as compared to the residual effects of foramsulfuron alone.
Abstract: In Algeria, now, the oil pumping plants are fed with electric power by independent local sources. This type of feeding has many advantages (little climatic influence, independent operation). However it requires a qualified maintenance staff, a rather high frequency of maintenance and repair and additional fuel costs. Taking into account the increasing development of the national electric supply network (Sonelgaz), a real possibility of transfer of the local sources towards centralized sources appears.These latter cannot only be more economic but more reliable than the independent local sources as well. In order to carry out this transfer, it is necessary to work out an optimal strategy to rebuilding these networks taking in account the economic parameters and the indices of reliability.
Abstract: Compost manufacturing plants are one of units where
wastewater is produced in significantly large amounts. Wastewater
produced in these plants contains high amounts of substrate (organic
loads) and is classified as stringent waste which creates significant
pollution when discharged into the environment without treatment. A
compost production plant in the one of the Iran-s province treating
200 tons/day of waste is one of the most important environmental
pollutant operations in this zone. The main objectives of this paper
are to investigate the compost wastewater treatability in hybrid
anaerobic reactors with an upflow-downflow arrangement, to
determine the kinetic constants, and eventually to obtain an
appropriate mathematical model. After starting the hybrid anaerobic
reactor of the compost production plant, the average COD removal
rate efficiency was 95%.
Abstract: This study was conducted to determine effect of water stress on chlorophyll content and chlorophyll fluorescence parameter in young `Dezful- olive trees. Three irrigation regimes (40% ETcrop, 65% ETcrop and 100% ETcrop) were used. After irrigation treatments were applied, some of biochemical parameters including chlorophyll a, b, total chlorophyll, chlorophyll fluorescence and also chlorophyll content index (C.C.I) were measured. Results of Analysis of variance showed that irrigation treatments had significant effect on chlorophylla, total chlorophyll (chl a+b), C.C.I and Fv/Fm ratio. The amount of decreased chlorophyll a and total chlorophyll in plants were received 40% ETcrop were 51.55% and 46.86%, respectively, compared with 100% ETcrop.
Abstract: Oxide scale thickness measurements are used in assessing the life of different components operating at high temperature environment. Such measurements provide an approximation for the temperature inside components such as reheater and superheater tubes. A number of failures were encountered in one of the boilers in one of Kuwaiti power plants. These failure were mainly in the first row of the primary super heater tubes, therefore, the specialized engineer decide to replace them during the annual shutdown. As a tool for failure analysis, oxide scale thickness measurement were used to investigate the temperature distribution in these tubes. In this paper, the oxide scale thickness of these tubes were measured and used for analysis. The measurements provide an illustration of the distribution of heat transfer of the primary superheater tubes in the boiler system. Remarks and analysis about the design of the boiler are also provided.
Abstract: The present disposal routes of sewage sludge represent a critical environmental issue in Egypt. Recently, there has been an increasing concern about sewage sludge management due to the environmental risks, which resulted from the fast expansion of wastewater treatment plants without equal attention in dealing with the produced sludge. This paper discusses the current situation of sewage sludge management in Egypt presenting a brief overview of the existing wastewater treatment plants, sludge production and characteristics as well as options of beneficial use and potential demand of sewage sludge under Egyptian conditions. The characteristics of sewage sludge are discussed considering the results of own sampling and analysis as well as previous studies. Furthermore, alternative treatment scenarios for sewage sludge, which have been recently developed in Egypt, are discussed and perspectives for a sustainable agricultural use are outlined.
Abstract: Most parts of the world such as Iran are facing the excessive consumption of fertilizers, that are used to achieve high yield, but increase the cost of production of fertilizer and degradation of soil and water resources. This experiment was carried out to study the effect of PGPR and planting pattern on yield and yield components of rice (Oryza sativa L.) using split plot based on randomized complete block design with three replications in Ilam province, Iran. Bio-fertilizer including Azotobacter, Nitroxin and control treatment (without consumption) were designed as a main plot and planting pattern including 15 × 10, 15 × 15 and 15 × 20 and the number of plant in hill including 3, 4 and 5 plants in hill were considered as a sub-plots. The results showed that the effect of bio-fertilizers, planting pattern and the number of plants in hill were significant affect on yield and yield components. Interaction effect between bio-fertilizer and planting pattern had important difference on the number spikelet of panicle and harvest index. Interaction effect between bio-fertilizer and the number of plants in hill were significant affect on the number of spikelet per panicle. The maximum grain yield was obtained by inoculation with Nitroxin, planting pattern of 15 × 15 and 4 plants in hill with mean of 1110.6 g.m-2, 959.9 g.m-2 and 928.4 g.m-2, respectively.
Abstract: Macrophomina phaseolina is a devastating soil-borne
fungal plant pathogen that causes charcoal rot disease in many
economically important crops worldwide. So far, no registered
fungicide is available against this plant pathogen. This study was
planned to examine the antifungal activity of an allelopathic grass
Cenchrus pennisetiformis (Hochst. & Steud.) Wipff. for the
management of M. phaseolina isolated from cowpea [Vigna
unguiculata (L.) Walp.] plants suffering from charcoal rot disease.
Different parts of the plants viz. inflorescence, shoot and root were
extracted in methanol. Laboratory bioassays were carried out using
different concentrations (0, 0.5, 1.0, …, 3.0 g mL-1) of methanolic
extracts of the test allelopathic grass species to assess the antifungal
activity against the pathogen. In general, extracts of all parts of the
grass exhibited antifungal activity. All the concentrations of
methanolic extracts of shoot and root significantly reduced fungal
biomass by 20–73% and 40–80%, respectively. Methanolic shoot
extract was fractionated using n-hexane, chloroform, ethyl acetate
and n-butanol. Different concentrations of these fractions (3.125,
6.25, …, 200 mg mL-1) were analyzed for their antifungal activity.
All the concentrations of n-hexane fraction significantly reduced
fungal biomass by 15–96% over corresponding control treatments.
Higher concentrations (12.5–200 mg mL-1) of chloroform, ethyl
acetate and n-butanol also reduced the fungal biomass significantly
by 29–100%, 46–100% and 24–100%, respectively.
Abstract: Trends in business intelligence, e-commerce and
remote access make it necessary and practical to store data in
different ways on multiple systems with different operating systems.
As business evolve and grow, they require efficient computerized
solution to perform data update and to access data from diverse
enterprise business applications. The objective of this paper is to
demonstrate the capability of DTS [1] as a database solution for
automatic data transfer and update in solving business problem. This
DTS package is developed for the sales of variety of plants and
eventually expanded into commercial supply and landscaping
business. Dimension data modeling is used in DTS package to
extract, transform and load data from heterogeneous database
systems such as MySQL, Microsoft Access and Oracle that
consolidates into a Data Mart residing in SQL Server. Hence, the
data transfer from various databases is scheduled to run automatically
every quarter of the year to review the efficient sales analysis.
Therefore, DTS is absolutely an attractive solution for automatic data
transfer and update which meeting today-s business needs.