Abstract: In the present study, Convective heat transfer
coefficient and pressure drop of Al2O3/water nanofluid in laminar
flow regime under constant heat flux conditions inside a circular tube
were experimentally investigated. Al2O3/water nanofluid with 0.5%
and 1% volume concentrations with 15 nm diameter nanoparticles
were used as working fluid. The effect of different volume
concentrations on convective heat transfer coefficient and friction
factor was studied. The results emphasize that increasing of particle
volume concentration leads to enhance convective heat transfer
coefficient. Measurements show the average heat transfer coefficient
enhanced about 11-20% with 0.5% volume concentration and
increased about 16-27% with 1% volume concentration compared to
distilled water. In addition, the convective heat transfer coefficient of
nanofluid enhances with increase in heat flux. From the results, the
average ratio of (fnf/fbf) was about 1.10 for 0.5% volume
concentration. Therefore, there is no significant increase in friction
factor for nanofluids.
Abstract: Automatic keyphrase extraction is useful in efficiently
locating specific documents in online databases. While several
techniques have been introduced over the years, improvement on
accuracy rate is minimal. This research examines attribute scores for
author-supplied keyphrases to better understand how the scores affect
the accuracy rate of automatic keyphrase extraction. Five attributes
are chosen for examination: Term Frequency, First Occurrence, Last
Occurrence, Phrase Position in Sentences, and Term Cohesion
Degree. The results show that First Occurrence is the most reliable
attribute. Term Frequency, Last Occurrence and Term Cohesion
Degree display a wide range of variation but are still usable with
suggested tweaks. Only Phrase Position in Sentences shows a totally
unpredictable pattern. The results imply that the commonly used
ranking approach which directly extracts top ranked potential phrases
from candidate keyphrase list as the keyphrases may not be reliable.
Abstract: In this paper, we propose the pre-processor based on
the Evidence Supporting Measure of Similarity (ESMS) filter and also
propose the unified fusion approach (UFA) based on the general
fusion machine coupled with ESMS filter, which improve the
correctness and precision of information fusion in any fields of
application. Here we mainly apply the new approach to Simultaneous
Localization And Mapping (SLAM) of Pioneer II mobile robots. A
simulation experiment was performed, where an autonomous virtual
mobile robot with sonar sensors evolves in a virtual world map with
obstacles. By comparing the result of building map according to the
general fusion machine (here DSmT-based fusing machine and
PCR5-based conflict redistributor considereded) coupling with ESMS
filter and without ESMS filter, it shows the benefit of the selection of
the sources as a prerequisite for improvement of the information
fusion, and also testifies the superiority of the UFA in dealing with
SLAM.
Abstract: Acoustic Imaging based sound localization using microphone
array is a challenging task in digital-signal processing.
Discrete Fourier transform (DFT) based near-field acoustical holography
(NAH) is an important acoustical technique for sound source
localization and provide an efficient solution to the ill-posed problem.
However, in practice, due to the usage of small curtailed aperture
and its consequence of significant spectral leakage, the DFT could
not reconstruct the active-region-of-sound (AROS) effectively, especially
near the edges of aperture. In this paper, we emphasize the
fundamental problems of DFT-based NAH, provide a solution to
spectral leakage effect by the extrapolation based on linear predictive
coding and 2D Tukey windowing. This approach has been tested to
localize the single and multi-point sound sources. We observe that
incorporating extrapolation technique increases the spatial resolution,
localization accuracy and reduces spectral leakage when small curtail
aperture with a lower number of sensors accounts.
Abstract: In this paper we use data mining techniques to investigate factors that contribute significantly to enhancing the risk of acute coronary syndrome. We assume that the dependent variable is diagnosis – with dichotomous values showing presence or absence of disease. We have applied binary regression to the factors affecting the dependent variable. The data set has been taken from two different cardiac hospitals of Karachi, Pakistan. We have total sixteen variables out of which one is assumed dependent and other 15 are independent variables. For better performance of the regression model in predicting acute coronary syndrome, data reduction techniques like principle component analysis is applied. Based on results of data reduction, we have considered only 14 out of sixteen factors.
Abstract: The enthusiasm for gluten avoidance in a growing
market is met by improvements in sensitive detection methods for
analysing gluten content. Paradoxically, manufacturers employ no
such systems in the production process but continue to market their
product as gluten free, a significant risk posed to an undetermined
coeliac population. This paper resonates with an immunological
response that causes gastrointestinal scarring and villous atrophy with
the conventional description of personal injury. This thesis divulges
into evaluating potential inadequacies of gluten labelling laws which
not only present a diagnostic challenge for general practitioners in the
UK but it also exposes a less than adequate form of available legal
protection to those who suffer adverse reactions as a result of gluten
digestion. Central to this discussion is whether a claim brought in
misrepresentation, negligence and/or under the Consumer Protection
Act 1987 could be sustained. An interesting comparison is then made
with the legal regimes of neighboring jurisdictions furthering the
theme of a legally un-catered for gluten kingdom.
Abstract: The paper provides biomasses characteristics by
proximate analysis (volatile matter, fixed carbon and ash) and
ultimate analysis (carbon, hydrogen, nitrogen and oxygen) for the
prediction of the heating value equations. The heating value
estimation of various biomasses can be used as an energy evaluation.
Thirteen types of biomass were studied. Proximate analysis was
investigated by mass loss method and infrared moisture analyzer.
Ultimate analysis was analyzed by CHNO analyzer. The heating
values varied from 15 to 22.4MJ kg-1. Correlations of the calculated
heating value with proximate and ultimate analyses were undertaken
using multiple regression analysis and summarized into three and two
equations, respectively. Correlations based on proximate analysis
illustrated that deviation of calculated heating values from
experimental heating values was higher than the correlations based
on ultimate analysis.
Abstract: Text categorization is the problem of classifying text
documents into a set of predefined classes. After a preprocessing
step, the documents are typically represented as large sparse vectors.
When training classifiers on large collections of documents, both the
time and memory restrictions can be quite prohibitive. This justifies
the application of feature selection methods to reduce the
dimensionality of the document-representation vector. In this paper,
three feature selection methods are evaluated: Random Selection,
Information Gain (IG) and Support Vector Machine feature selection
(called SVM_FS). We show that the best results were obtained with
SVM_FS method for a relatively small dimension of the feature
vector. Also we present a novel method to better correlate SVM
kernel-s parameters (Polynomial or Gaussian kernel).
Abstract: The main purpose of this research was to study how to communicate the identity of the Bangpoo, Samu tPrakan province for ecotourism. The qualitative data was collected through studying related materials, exploring the area, in-depth interviews with three groups of people: three directly responsible officers who were key informants of the district, twenty foreign tourists and five Thai tourist guides. A content analysis was used to analyze the qualitative data. The two main findings of the study were as follows:
The identity of Bangpoo, Samut Prakan province. This establishment was near the Mouth of the Gulf of Thailand for normal people and tourists, consisting of rest accommodations. There are restaurants where food and drinks are served, rich mangrove forests, Banpoo seaside resort and mangrove trees. Bangpoo seaside resort is characterized by muddy beacheswhere the greatest number of seagulls can be seen from March to May each year.
The communication of the identity of Bangpoo, Samut Prakan province which the researcher could find and design to present in English materials can be summed up in 3 items: 1) The history of Bangpoo, Samut Prakan province 2) The Learning center of Ecotourism: Seagulls and Mangrove forest 3) How to keep Banpoo, Samut Prakran province for ecotourism.
Abstract: Surface roughness (Ra) is one of the most important requirements in machining process. In order to obtain better surface roughness, the proper setting of cutting parameters is crucial before the process take place. This research presents the development of mathematical model for surface roughness prediction before milling process in order to evaluate the fitness of machining parameters; spindle speed, feed rate and depth of cut. 84 samples were run in this study by using FANUC CNC Milling α-Τ14ιE. Those samples were randomly divided into two data sets- the training sets (m=60) and testing sets(m=24). ANOVA analysis showed that at least one of the population regression coefficients was not zero. Multiple Regression Method was used to determine the correlation between a criterion variable and a combination of predictor variables. It was established that the surface roughness is most influenced by the feed rate. By using Multiple Regression Method equation, the average percentage deviation of the testing set was 9.8% and 9.7% for training data set. This showed that the statistical model could predict the surface roughness with about 90.2% accuracy of the testing data set and 90.3% accuracy of the training data set.
Abstract: On a such wide-area environment as a Grid, data
placement is an important aspect of distributed database systems. In
this paper, we address the problem of initial placement of database
no-replicated fragments in Grid architecture. We propose a graph
based approach that considers resource restrictions. The goal is to
optimize the use of computing, storage and communication
resources. The proposed approach is developed in two phases: in the
first phase, we perform fragment grouping using knowledge about
fragments dependency and, in the second phase, we determine an
efficient placement of the fragment groups on the Grid. We also
show, via experimental analysis that our approach gives solutions
that are close to being optimal for different databases and Grid
configurations.
Abstract: Artificial Neural Network (ANN)s are best suited for
prediction and optimization problems. Trained ANNs have found
wide spread acceptance in several antenna design systems. Four
parameters namely antenna radiation resistance, loss resistance, efficiency,
and inductance can be used to design an antenna layout though
there are several other parameters available. An ANN can be trained
to provide the best and worst case precisions of an antenna design
problem defined by these four parameters. This work describes the
use of an ANN to generate the four mentioned parameters for a loop
antenna for the specified frequency range. It also provides insights
to the prediction of best and worst-case design problems observed
in applications and thereby formulate a model for physical layout
design of a loop antenna.
Abstract: This paper presents a novel method for remaining
useful life prediction using the Elliptical Basis Function (EBF)
network and a Markov chain. The EBF structure is trained by a
modified Expectation-Maximization (EM) algorithm in order to take
into account the missing covariate set. No explicit extrapolation is
needed for internal covariates while a Markov chain is constructed to
represent the evolution of external covariates in the study. The
estimated external and the unknown internal covariates constitute an
incomplete covariate set which are then used and analyzed by the EBF
network to provide survival information of the asset. It is shown in the
case study that the method slightly underestimates the remaining
useful life of an asset which is a desirable result for early maintenance
decision and resource planning.
Abstract: In this longitudinal study, we examined the moderating role of personality in the relationship between communication behaviors and long-term dyadic adjustment. A sample of 82 couples completed the NEO Five-Factor Inventory and the Dyadic Adjustment Scale. These couples were also videotaped during a 15-minute problem-solving discussion. Approximately 2.5 years later, these couples completed again the Dyadic Adjustment Scale. Results show that personality of both men and women moderates the relationship between communication behaviors of the partner and long-term dyadic adjustment of the individual. Women-s openness and men-s extraversion moderate the relationship between some communication behaviors and long-term dyadic adjustment
Abstract: Time series forecasting is an important and widely
popular topic in the research of system modeling. This paper
describes how to use the hybrid PSO-RLSE neuro-fuzzy learning
approach to the problem of time series forecasting. The PSO
algorithm is used to update the premise parameters of the
proposed prediction system, and the RLSE is used to update the
consequence parameters. Thanks to the hybrid learning (HL)
approach for the neuro-fuzzy system, the prediction performance
is excellent and the speed of learning convergence is much faster
than other compared approaches. In the experiments, we use the
well-known Mackey-Glass chaos time series. According to the
experimental results, the prediction performance and accuracy in
time series forecasting by the proposed approach is much better
than other compared approaches, as shown in Table IV. Excellent
prediction performance by the proposed approach has been
observed.
Abstract: This paper presents the methodology from machine
learning approaches for short-term rain forecasting system. Decision
Tree, Artificial Neural Network (ANN), and Support Vector Machine
(SVM) were applied to develop classification and prediction models
for rainfall forecasts. The goals of this presentation are to
demonstrate (1) how feature selection can be used to identify the
relationships between rainfall occurrences and other weather
conditions and (2) what models can be developed and deployed for
predicting the accurate rainfall estimates to support the decisions to
launch the cloud seeding operations in the northeastern part of
Thailand. Datasets collected during 2004-2006 from the
Chalermprakiat Royal Rain Making Research Center at Hua Hin,
Prachuap Khiri khan, the Chalermprakiat Royal Rain Making
Research Center at Pimai, Nakhon Ratchasima and Thai
Meteorological Department (TMD). A total of 179 records with 57
features was merged and matched by unique date. There are three
main parts in this work. Firstly, a decision tree induction algorithm
(C4.5) was used to classify the rain status into either rain or no-rain.
The overall accuracy of classification tree achieves 94.41% with the
five-fold cross validation. The C4.5 algorithm was also used to
classify the rain amount into three classes as no-rain (0-0.1 mm.),
few-rain (0.1- 10 mm.), and moderate-rain (>10 mm.) and the overall
accuracy of classification tree achieves 62.57%. Secondly, an ANN
was applied to predict the rainfall amount and the root mean square
error (RMSE) were used to measure the training and testing errors of
the ANN. It is found that the ANN yields a lower RMSE at 0.171 for
daily rainfall estimates, when compared to next-day and next-2-day
estimation. Thirdly, the ANN and SVM techniques were also used to
classify the rain amount into three classes as no-rain, few-rain, and
moderate-rain as above. The results achieved in 68.15% and 69.10%
of overall accuracy of same-day prediction for the ANN and SVM
models, respectively. The obtained results illustrated the comparison
of the predictive power of different methods for rainfall estimation.
Abstract: The mechanical properties of blends consisting of
plasticized poly(vinyl butyral) (PVB) and plasticized poly(vinyl
chloride) (PVC) are studied, in order to evaluate the possibility of
using recycled PVB waste derived from windshields. PVC was
plasticized with 38% of diisononyl phthalate (DINP), while PVB was
plasticized with 28% of triethylene glycol, bis(2-ethylhexanoate)
(3GO). The optimal process conditions for the PVB/PVC blend in 1:1
ratio were determined. Entropy was used in order to theoretically
predict the blends miscibility. The PVB content of each blend
composition used was ranging from zero to 100%. Tensile strength
and strain were tested. In addition, a comparison between recycled
and original PVB, used as constituents of the blend, was performed.
Abstract: Tool wear and surface roughness prediction plays a
significant role in machining industry for proper planning and control
of machining parameters and optimization of cutting conditions. This
paper deals with developing an artificial neural network (ANN)
model as a function of cutting parameters in turning steel under
minimum quantity lubrication (MQL). A feed-forward
backpropagation network with twenty five hidden neurons has been
selected as the optimum network. The co-efficient of determination
(R2) between model predictions and experimental values are 0.9915,
0.9906, 0.9761 and 0.9627 in terms of VB, VM, VS and Ra
respectively. The results imply that the model can be used easily to
forecast tool wear and surface roughness in response to cutting
parameters.
Abstract: The aim of study was to evaluate pressure distribution characteristics of the elastic textile bandages using two instrumental techniques: a prototype Instrument and a load Transference. The prototype instrument which simulates shape of real leg has pressure sensors which measure bandage pressure. Using this instrument, the results show that elastic textile bandages presents different pressure distribution characteristics and none produces a uniform distribution around lower limb.
The load transference test procedure is used to determine whether a relationship exists between elastic textile bandage structure and pressure distribution characteristics. The test procedure assesses degree of load, directly transferred through a textile when loads series are applied to bandaging surface. A range of weave fabrics was produced using needle weaving machine and a sewing technique. A textile bandage was developed with optimal characteristics far superior pressure distribution than other bandages. From results, we find that theoretical pressure is not consistent exactly with practical pressure. It is important in this study to make a practical application for specialized nurses in order to verify the results and draw useful conclusions for predicting the use of this type of elastic band.
Abstract: The purpose of determining impact significance is to
place value on impacts. Environmental impact assessment review is a
process that judges whether impact significance is acceptable or not in
accordance with the scientific facts regarding environmental,
ecological and socio-economical impacts described in environmental
impact statements (EIS) or environmental impact assessment reports
(EIAR). The first aim of this paper is to summarize the criteria of
significance evaluation from the past review results and accordingly
utilize fuzzy logic to incorporate these criteria into scientific facts. The
second aim is to employ data mining technique to construct an EIS or
EIAR prediction model for reviewing results which can assist
developers to prepare and revise better environmental management
plans in advance. The validity of the previous prediction model
proposed by authors in 2009 is 92.7%. The enhanced validity in this
study can attain 100.0%.